Sony MFM-HT75W User Manual - Page 38

Trouble symptoms and remedies - mfmht75ws

Get Sony MFM-HT75W PDF manuals and user guides View all Sony MFM-HT75W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Trouble symptoms and remedies If a problem occurs as a result of a connected computer or other equipment, refer to the connected computer/equipment's instruction manual. For PC 1/PC 2 Symptom No picture. If the 1 (power) indicator is not lit, or if the 1 (power) indicator will not light up when the 1 (power) switch is pressed, If "Cable Disconnected" appears on the screen, If "No Input Signal" appears on the screen, or the 1 (power) indicator is orange, If "Out of Range" appears on the screen (page 36), If using Windows, If using a Macintosh system, Check these items • Check that the power cord is properly connected. • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 9). • Check that the video input connector's pins are not bent or pushed in. • Check that the input select setting is correct (page 12). • A non-supplied video signal cable is connected. If you connect a non-supplied video signal cable, "Cable Disconnected" may appear on the screen. This is not a malfunction. • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 9). • Check that the video input connector's pins are not bent or pushed in. • Check that the input select setting is correct (page 12). xProblem caused by a computer or other equipment connected, and not caused by the display • The computer is in the power saving mode. Try pressing any key on the keyboard or moving the mouse. • Check that your graphics board is installed properly. • Check that the computer's power is on. • Restart the computer. xProblem caused by a computer or other equipment connected, and not caused by the display • Check that the video frequency range is within that specified for the display. If you replaced an old display with this display, reconnect the old display and adjust the computer's graphics board within the following ranges: MFM-HT75W Horizontal frequency: 28-69 kHz (Analog RGB), 28-48 kHz (Digital RGB) Vertical frequency: 48-85 Hz (Analog RGB), 60 Hz (Digital RGB) Resolution: 1280 × 768 or less MFM-HT95 Horizontal frequency: 28-86 kHz (Analog RGB), 28-64 kHz (Digital RGB) Vertical frequency: 48-85 Hz (Analog RGB, resolution

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
38
Trouble symptoms and remedies
If a problem occurs as a result of a connected computer or other equipment, refer to the connected computer/equipment’s instruction manual.
For PC 1/PC 2
Symptom
Check these items
No picture.
If the
1
(power) indicator is not lit,
or if the
1
(power) indicator will not
light up when the
1
(power) switch
is pressed,
•
Check that the power cord is properly connected.
If “Cable Disconnected” appears on
the screen,
•
Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 9).
•
Check that the video input connector’s pins are not bent or pushed in.
•
Check that the input select setting is correct (page 12).
•
A non-supplied video signal cable is connected. If you connect a non-supplied video
signal cable, “Cable Disconnected” may appear on the screen. This is not a malfunction.
If “No Input Signal” appears on the
screen, or the
1
(power) indicator is
orange,
•
Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 9).
•
Check that the video input connector’s pins are not bent or pushed in.
•
Check that the input select setting is correct (page 12).
x
Problem caused by a computer or other equipment connected, and not
caused by the display
•
The computer is in the power saving mode. Try pressing any key on the keyboard or
moving the mouse.
•
Check that your graphics board is installed properly.
•
Check that the computer’s power is on.
•
Restart the computer.
If “Out of Range” appears on the
screen (page 36),
x
Problem caused by a computer or other equipment connected, and not
caused by the display
•
Check that the video frequency range is within that specified for the display. If you
replaced an old display with this display, reconnect the old display and adjust the
computer’s graphics board within the following ranges:
MFM-HT75W
Horizontal frequency: 28–69 kHz (Analog RGB), 28–48 kHz (Digital RGB)
Vertical frequency: 48–85 Hz (Analog RGB), 60 Hz (Digital RGB)
Resolution: 1280
×
768 or less
MFM-HT95
Horizontal frequency: 28–86 kHz (Analog RGB), 28–64 kHz (Digital RGB)
Vertical frequency: 48–85 Hz (Analog RGB, resolution<1280
×
1024), 48–75 Hz (Analog
RGB, resolution=1280
×
1024), 60 Hz (Digital RGB)
Resolution:1280
×
1024 or less
For the MFM-HT75W only
•
SXGA picture is displayed with Safe Display Mode but it may be fuzzy. Set the resolution
to 1280
×
768 on your computer.
If using Windows,
•
If you replaced an old display with this display, reconnect the old display and do the
following. Select “SONY” from the “Manufacturers” list and select “MFM-HT75W or
MFM-HT95” from the “Models” list on the Windows device selection screen. If “MFM-
HT75W or MFM-HT95” does not appear in the “Models” list, try “Plug & Play.”
If using a Macintosh system,
•
When connecting a Macintosh computer, use an adapter (not supplied) if necessary.
Connect the adapter to the computer before connecting the video signal cable.