Sony PFM-500A2WU Operating Instructions (primary manual)
Sony PFM-500A2WU Manual
View all Sony PFM-500A2WU manuals
Add to My Manuals
Save this manual to your list of manuals |
Sony PFM-500A2WU manual content summary:
- Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 1
3-866-789-02(1) Flat Panel Monitor Operating Instructions EN Mode d'emploi F Bedienungsanleitung D Manual de instrucciones ES Istruzioni per l'uso I J PFM-500A2WU PFM-500A2WE PFM-500A2WJ © 1999 by Sony Corporation - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 2
WARNING Owner's Record The model and serial numbers are located on the rear. Record the model and serial numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. Serial No. To prevent fire or shock hazard, do not - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 3
the AC Power Cord 16 (EN) Connection Example 17 (EN) Using On-screen Menus 18 (EN) Operating Through Menus 18 (EN) Menu Guide 18 (EN) EN Watching the Picture 22 (EN) Switching the Picture 22 (EN) Watching a Still Picture 22 (EN) Input Signal and Monitor Status Information Display 22 (EN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 4
• To disconnect the AC power cord, pull it out Plasma Display Panel) • There may be some tiny black points and/or bright points on the PDP. These points are normal. • Do not display a same still image on the screen for long, consecutive time. Otherwise, the afterimage may appear on a part of a panel - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 5
The PFM-500A2W series are 16:9 42-inch flat panel monitor adopting the PDP (Plasma Display Panel) and accepts various types of signals with the built-in scan converter. Improved image quality Higher image quality is gained with the new PDP - improving brightness more than conventional monitors. An - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 6
. You can install the Remote Commander in the back of this cover. For details on opening the panel cover, see the right on this page. 2 Left connector panel For details on the left connector panel, see "Left Connector Panel" on page 11(EN). 3 Retractable feet Use for setting the monitor on the floor - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 7
Loosen the screws as illustrated below and take off the panel cover. Screws To install the Remote Commander in the panel cover Install the Remote Commander in the back of the left panel cover as illustrated below. Remote Commander Note When housing the Remote Commander, make sure that the top of the - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 8
Parts and Controls Control Panel VOL - VOL + MENU . > ENT RGB1 YUV RGB2 LINE Y/C CTRL u !£ !™ !¡ 0 98765 4 32 1 1 Remote control detector Receives the beam from the Remote Commander. 2 u (standby) switch/u (standby) indicator Press to turn the monitor input from the VIDEO IN connector - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 9
Right Connector Panel RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 RGB1 IN connectors R (R-Y)/G (Y)/B (B-Y) IN (BNC-type): Input the analog RGB signal or component signal. - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 10
. AUDIO OUT (L/R) (phono type): Loop-through outputs of the AUDIO IN jacks. Connect to the audio inputs of another monitor or video equipment. 6 REMOTE (RS-232C) connector (mini DIN 8pin) This connector allows remote control of the monitor using the RS-232C protocol. For details, see your authorized - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 11
not connect the speaker's cord to the monitor and to an amplifier simultaneously, or an excessive electric current might flow from the amplifier and damage the monitor. 4 SERVICE CODE indicator This indicator is only for qualified personnel. 5 ⁄AC IN socket Connect the supplied AC power cord to this - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 12
Location and Function of Parts and Controls Remote Commander RM-921 1 !™ MUTING DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER ON SELECT MENU !¶ 9 !• OFF 0 ENTER !ª ON @º SET VOL CH !¡ OFF @¡ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 13
number appear on the screen. Then press the index number of the monitor you want to operate and press the SET button. After you finish the operation, press the OFF button to return to the normal mode. !™ DISPLAY button Displays to half a year. If the Remote Commander does not operate properly, the - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 14
retractable feet. To fix the retractable feet When the unit is installed on the floor, be sure to fix the retractable feet. Install the foot support brackets as illustrated below. 2 Turn the retractable feet outward. 3 Push in the retractable feet and lock. 14 (EN) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 15
Caution • When you install the monitor, make sure there is more space than that shown in the figure below. • The ambient temperature must be 0°C - +35°C (32°F - 95°F). When using the retractable - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 16
Connections Connecting the AC Power Cord 1 Plug the power cord into the AC IN socket. Then, attach the AC plug holder (supplied) to the AC power cord. AC IN socket AC power cord AC plug holder 2 Slide the AC plug holder over the cord until it connects to the AC IN socket cover. AC IN socket - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 17
Before you get started • First make sure that the power to each piece of equipment is turned off. • cable itself. • Read the instruction manual of the equipment to be connected. Computer Betacam SP video cassette recorder to audio output to video output to video to audio output output VCR, - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 18
Guide Menu operating buttons There are four buttons on the monitor and the Remote Commander for menu operations. Remote Commander SELECT MENU Monitor MENU . > ENT ENTER The buttons on the control panel are used for explanation purpose in this operating instructions on the monitor screen. 3 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 19
The moiré pattern or noise decreases even the screen looks a little blurred. !¶ DISPLAY Select ON to display the input signal information for about five seconds on the top of the monitor screen when turning on the power or switching the input signal. !• POWER SAVE Set the time period to activate the - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 20
Sets the index number of the monitor. Note When you set the number, use the buttons on the monitor. For details on the index number, see "Operating a Specific Monitor With the Remote Commander" on page 32(EN). @£ REMOTE MODE Select the Remote Commander mode. TV: Sony monitors' or TVs' commander PJ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 21
displaying the internal condition of the monitor. @∞ STATUS @§ [ P F M - 5 0 0 A 2WU ] @¶ SER I AL No . OPERA T I ON : 2000001 : 000000H @• SO F TWA R E : Ver 1 . 0 0 @ª T EMPERA TURE : FAN : OK OK #º @∞ Model name Indicates the model name. @§ SERIAL No. Indicates the serial number - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 22
you start • Turn on the monitor. • Turn on the connected equipment and play a video source. • To display the input signal information on the screen when turning on the power or switching the input signal, set "DISPLAY" in the CONFIG menu to ON. • To select the on-screen language used in the menu - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 23
sync signal to the G/Y IN connector. Actual on-screen display of the monitor status On-screen display Significance 31.5kHz / 60Hz (eg.) The selected input signal is computer RGB. 525 / 60 (eg.) The selected input signal is RGB or component video. NTSC The selected input signal is NTSC. PAL - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 24
the adjusted levels in memory. Adjusting the Contrast, Brightness, Chroma, and Phase Press MENU so that the main menu appears on the monitor screen and select the "CONTRAST", "BRIGHTNESS", "CHROMA", or "PHASE" from the PIC CONTROL menu with the >/. buttons. CONTRAST Select the "CONTRAST" with the - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 25
Settings 1 In the PIC CONTROL menu, Press >/. to move the cursor (z) to "RESET" and press ENT. The following menu appears on the monitor screen. RESET : NO 4 Press >/. to set "PICTURE AGC" to ON. 5 Press ENT. The menu returns to the PIC CONTROL menu. S E L E C T ENTER C A N C E L MENU 2 Press - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 26
H SH I FT : 00 4 Press >/. to resize the picture. >: to expand horizontal size .: to reduce horizontal size The horizontal picture size is indicated on the monitor screen in the range from MIN(-50) to MAX(+50). The factory value is 00. 2 Press >/. to shift the picture. >: to shift the picture to - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 27
Picture You can also operate with the ZOOM button on the Remote Commander. 1 In the PIC SIZE menu, press >/. to move the cursor (z) to "ZOOM" and press ENT. The following menu appears on the monitor screen. Z OOM : x1 S E L E C T ENTER C A N C E L MENU 3 Press ENT. The original picture size - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 28
to move the cursor (z) to "MEMORY" and press ENT. The MEMORY menu appears on the monitor screen. MEMOR Y LOAD SAVE S E L E C T ENTER C A N C E L MENU horizontal frequency/vertical frequency are now displayed on the right column next to the selected memory number. Signal type Color system or - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 29
Notes • You cannot recall the memory data if the selected signal is different from the preset signal. • The following items can be memorized: PIC CONTROL menu - CONTRAST - BRIGHTNESS - CHROMA - PHASE - COLOR TEMP - PICTURE AGC PIC SIZE menu - H SIZE - H SHIFT - V SIZE - V SHIFT - ZOOM - ASPECT - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 30
The following menu appears on the monitor screen. P OWE R S A V E : 5m To cancel the power saving function • Input the sync signal again. • Press the u switch on the control panel or the POWER switch on the Remote Commander. Signal specification for using the power saving function RGB1: When the - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 31
monitor screen. CONF I G ENHANCE H F I L TER D I SPLAY P OWE R S A V E L ANGUAGE : H I GH : AUTO : ON : 5m S E L E C T ENTER C A N C E L MENU The unit has a self-diagnosis function. This function displays the monitor's condition with the u indicator flashing and numbers on the SERVICE CODE - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 32
MOD E : TV R EMO T E ON L Y : O F F S E L E C T ENTER C A N C E L MENU 3 Press >/. to move the cursor (z) to "INDEX NO." and press ENT. The following menu appears on the monitor screen. I NDEX NO . : 001 ' 4 Select the index number with >/. and press ENT. The menu returns to the REMOTE menu. - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 33
: contrast, phase and chroma • On-screen display on/off (only for video monitors and TVs) The available operations and the buttons to be used for each operation are limited depending on each Remote Commander. See the table below. Remote Commander model REMOTE MODE setting Input selection RGB1 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 34
Preset signal Input: 12 formats (See page 23(EN)) Video memory 1,152 × 1,152 × 24 bits (RGB total) Sampling rate 14.3 to 50 MHz offset phase max. (equivalent to 100 MHz sampling) Panel system AC-type Plasma Display Panel Display resolution 852 dots × 480 lines Pixel pitch 1.08(horizontal - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 35
45 kg (99 lb 3 oz) Supplied accessories AC power cord (1) AC plug holder (1) Remote Commander RM-921 (1) Size AA (R6) batteries (2) Ferrite core (2) Foot support bracket (2) Screws for foot support bracket (6) Monitor stabilizer (2) Operating instructions (1) Design and specifications are - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 36
amené à prendre des mesures appropriées. Aux utilisateurs de PFM-500A2E CET APPAREIL DOIT ETRE RACCORDE ALA TERRE IMPORTANT Les couleurs des conducteurs de cordon d'alimentation secteur correspondent au code suivant: Vert-et-jaune : Terre Bleu : Neutre Brun : - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 37
de la prise d'alimentation secteur ..... 16 (F) Exemple de raccordement 17 (F) Utilisation des menus d'affichage 18 (F) Exploitation des menus 18 (F) Guide de menu 18 (F) Visualisation de l'image 22 (F) Commutation de l'image 22 (F) F Visualisation d'un arrêt sur image 22 (F) Affichage du - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 38
et faites-le vérifier par un personnel qualifié avant de le remettre en service. • Débranchez le cordon de la prise si vous prévoyez de ne la télécommande, image parasitée, son parasité. PDP (Ecran d'affichage à plasma) • Il se peut qu'il y ait de minuscules points noirs et Sony agréé. 4 (F) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 39
PFM-500A2W sont des moniteurs 16:9e à panneau plat de 42 pouces adoptant le PDP (écran d'affichage à plasma Accepte les signaux des télécommandes infrarouges ou filaires Sony utilisant le code SIRCS. • Trois jeux d'entrée vidéo • Connecteur CONTROL S • Connecteur REMOTE (RS-232C) (mini connecteur - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 40
Emplacement et fonction des pièces et commandes Avant / Côtés Côté gauche Avant Côté droit 6 1 2 3 4 5 1 Couvercle du panneau gauche Ouvrez-le lorsque vous utilisez le panneau du connecteur gauche. Vous pouvez installer la télécommande à l'arrière de ce couvercle. Pour plus de détails sur - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 41
Pour ôter le couvercle du panneau Desserrez les vis comme illustré ci-dessous et retirez le couvercle du panneau. Vis Pour installer la télécommande dans le couvercle du panneau Mettez la télécommande en place à l'arrière du couvercle de panneau gauche comme illustré cidessous. Télécommande Remarque - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 42
l'entrée du signal à partir de la prise Y/C IN dans les connecteurs LINE. 6 Touche LINE Sélectionnez l'entrée de signal à partir du connecteur VIDEO IN dans les connecteurs LINE. 7 Touche RGB2 Sélectionnez l'entrée du signal à partir des connecteurs RGB2. 8 Touche YUV Sélectionnez l'entrée du signal - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 43
Panneau du connecteur droit RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 Connecteurs RGB1 IN R (R-Y)/G (Y)/B (B-Y) IN (type BNC): Entrez le signal RVB analogique ou le signal - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 44
Connecteurs LINE IN VIDEO IN (type VIDEO OUT ou à la prise Y/C OUT, la terminaison à 75 ohms du connecteur VIDEO IN la prise VIDEO IN ou Y/ C IN est émis à partir du connecteur VIDEO OUT ou de la prise Y/C OUT. VIDEO OUT moniteur ou équipement vidéo. 6 Connecteur REMOTE (RS-232C) (mini connecteur DIN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 45
1 VARIABLE CONTROL S IN OUT 2 SPEAKERS (6-16 Ω) + + R- L 3 - SERVICE CODE 8.8. 4 5 AC IN 1 Prises MONITOR OUT AUDIO (L/R) (type phono) Sortez permettra de commander simultanément tous les équipements au départ d'une seule télécommande. Pour commander l'équipement en orientant la - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 46
MUTING DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER SELECT !¶ . 4 Touche LINE Sélectionne l'entrée de signal à partir du connecteur VIDEO IN dans les connecteurs LINE. 12 (F) 5 Touche Y/C Sélectionne le - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 47
moniteurs, vous pouvez utiliser ce commutateur au lieu du commutateur 1 POWER pour ne pas affecter d'autres moniteurs déjà sous tension. !¡ Touches ée, appuyez sur la touche OFF pour revenir au mode normal. !™ Touche DISPLAY Affiche les informations de signal d'entrée en haut de l'écran du moniteur - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 48
les pieds rétractables. Pour fixer les pieds rétractables Si l'appareil est installé sur le sol, fixez les pieds rétractables. Mettez en place les supports de fixation de pied comme illustré ci-dessous. 2 Sortez les pieds rétractables. 3 Enfoncez les pieds rétractables et verrouillez-les. 14 (F) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 49
mur: verticalement Mur 10 (4) 10 (4) Mur Avant Mur 10 (4) Côté Sol 2,5 (1) 5,5 (2 1/4) ,,Mur ,,,,Sol ,, Unité: cm (pouces) Lors de l'utilisation du support de montage Avant Mur 25 (9 7/8) Mur 10 (4) 10 (4) Mur 20 (7 7/8) Mur 25 (9 7/8) Mur Assurez-vous que la section de commande - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 50
de prise AC (fourni) au cordon d'alimentation secteur. Prise AC IN Cordon d'alimentation secteur Support de prise d'alimentation 2 Faites glisser le support de prise d'alimentation secteur par-dessus le cordon jusqu'à ce qu'il s'enclenche dans le logement de la prise d'alimentation secteur - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 51
ou RVB RGB 1 IN OUT R R-Y G Y vers AUDIO IN vers RGB IN vers la sortie vers Y/C ou vidéo VIDEO IN B B-Y HD/ COMP VD SYNC L AUDIO R RGB 2 RGB IN L AUDIO IN R VIDEO Y/C * vers R(R-Y)/G(Y)/ B(B-Y) IN vers AUDIO IN vers AUDIO IN vers la sortie audio vers AUDIO IN L AUDIO R IN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 52
le menu revient au menu précédent. Pour revenir à l'écran normal, appuyez plusieurs fois sur la touche MENU jusqu'à ce que le menu disparaisse. Guide de menu Remarque "- - - -" apparaît en regard de l'option lorsque la fonction n'est pas disponible. La disponibilité dépend du type de signal d'entr - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 53
niveau de correction des contours: BAS: Réglage par défaut pour le signal VIDEO HAUT: Réglage par défaut pour le signal d'ordinateur !§ FILTRE H En moiré ou les parasites diminuent même si l'écran paraît légèrement trouble. !¶ AFFICHAGE Sélectionnez OUI pour afficher les informations du signal d'entr - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 54
spécifique avec la télécommande" à la page 32 (F). @£ MODE TELECOM Sélectionnez le mode de télécommande. TV: Télécommande de moniteurs ou de téléviseurs Sony PROJ: Télécommande de projecteurs Sony NON: Désactive la télécommande. Pour plus de détails, voir "Utilisation de l'autre télécommande" à la - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 55
ne sont pas bloqués et installez le moniteur dans une zone bien aérée. Si le message reste affiché, consultez votre distributeur Sony agréé. Lorsque l'indicateur u clignote ou NG s'affiche, voir "Fonction d'auto-diagnostic" à la page 31 (F). #º VENTILATEUR Des ventilateurs de refroidissement sont - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 56
composante. RGB2:Sélectionne le signal audio et vidéo entré par les connecteurs RGB2. LINE: Sélectionne le signal audio et vidéo entré par le connecteur VIDEO IN et la prise AUDIO IN dans les connecteurs LINE. Y/C: Sélectionne le signal audio et vidéo entré par le connecteur Y/C IN et la prise - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 57
, mettez "AFFICHAGE" sur OUI à l'étape 4 ci-dessus. Remarque Vous pouvez obtenir les informations d'entrée à n'importe quel moment en appuyant sur la touche DISPLAY de la télécommande, quel que soit le réglage ci-dessus. La liste d'information du signal d'entrée Système couleur ou fréquence - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 58
Réglage de l'image Pendant que vous visionnez l'image, vous pouvez régler le contraste, la luminosité, l'intensité des couleurs et la phase à votre gré. Ces réglages peuvent être exécutés séparément pour chacun des signaux d'entrée. Vous pouvez également enregistrer vos réglages dans la mémoire. Ré - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 59
3 Appuyez sur >/. pour déplacer le curseur (z) sur "IMAGE AUTO" et appuyez sur ENT. Le menu suivant apparaît sur l'écran du moniteur. I MAGE AUTO : NON 4 Appuyez sur >/. pour régler "IMAGE AUTO" sur OUI. 5 Appuyez sur ENT. Le menu retourne au menu CTRL IMAGE. Restauration des réglages par dé - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 60
Zoom, redimensionnement et repositionnement de l'image Vous pouvez décaler la position de l'image de manière à ce qu'elle s'adapte à l'écran, ou régler séparément la taille verticale et horizontale de l'image. Vous pouvez zoomer l'image de façon à la rendre deux, trois ou quatre fois plus grande. - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 61
3 Appuyez sur ENT. Le menu retourne au menu TAILLE IMAGE. 4 Appuyez sur >/. pour déplacer le curseur (z) sur "DEPL V" et appuyez sur ENT. Le menu suivant apparaît sur l'écran du moniteur. DEPL V : 00 Restauration de la taille et de la position originales de l'image 1 Dans le menu TAILLE IMAGE, - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 62
Utilisation de la mémoire Vous pouvez sauvegarder les réglages actuels de l'image pour chaque signal d'entrée à l'aide de la fonction MEMOIRE. Les réglages sauvegardés peuvent être rappelés à tout moment. Les options des menus CTRL IMAGE, TAILLE IMAGE et CONFIG (uniquement pour AMPLIF et FILTRE H) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 63
Remarques • Vous ne pouvez pas récupérer les données mémorisées si le signal sélectionné est différent du signal présélectionné. • Les options suivantes peuvent être mémorisées: Menu CTRL IMAGE - CONTRASTE - LUMINOSITE - CHROMA - PHASE - TEMP COULEUR - IMAGE AUTO Menu TAILLE IMAGE - AMPL H - DEPL H - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 64
fonction d'économie d'énergie • Entrez de nouveau un signal de synchro • Appuyez sur le commutateur u du panneau de commande ou sur le commutateur POWER de la télécommande. Spécification de signal pour l'utilisation de la fonction d'économie d'énergie RGB1: Lorsque le signal de synchro est raccord - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 65
normalement, seul le point en bas à droite de l'indicateur SERVICE CODE clignote. Si l'indicateur u clignote, vérifiez le chiffre et contactez votre distributeur Sony agréé. 1 Vérifiez le numéro à 2 chiffres de l'indicateur SERVICE CODE. L'indicateur affiche un numéro ou des numéros multiples - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 66
moniteur spécifié. (Toutes les opérations sont disponibles en mode ID sauf POWER ON/OFF.) 32 (F) 4 Après avoir effectué les réglages nécessaires l'écran du moniteur. T E L E COMMA N D E NO . I NDEX : 001 MOD E T E L E COM : TV T E L E COM I N I Q : NON S E L E C T ENTER A N N U L E R MENU - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 67
Réglage REMOTE MODE TV Sélection de l'entrée RGB1 RGB RGB 2 - LINE LINE1 Exploitation du menu MENU MENU ENTER ENTER + + - - Réglage de l'image Contraste CONTRAST+/- Intensité des couleurs CHROMA+/- Phase PHASE+/- Informations sur écran DISPLAY RM-1271 PJ A B VIDEO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 68
affichage à plasma de type Taille du panneau 42 pouces (diagonale 1. (NTSC, PAL) VIDEO IN Type BNC (×1) MONITOR OUT AUDIO (L, R) Prise phono (×2) Maximum 500 mVrms, haute impédance CONTROL S (IN, OUT) Mini prise (stéréo) (×2) 5 Vcc REMOTE (RS-232C) Miniconnecteur DIN à 8 broches SPEAKERS - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 69
Masse 45 kg (99 lb 3 oz) Accessoires fournis Cordon d'alimentation secteur (1) Support de prise secteur (1) Télécommande RM-921 (1) Piles R6 (AA) (2) Tore de ferrite (2) Support de fixation de pied (2) Vis de support de fixation de pied (6) Stabilisateur de moniteur (2) Mode d'emploi (1) La - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 70
A, es erfüllt nicht die Grenzwerte der Klasse B. HINWEIS Wenn Sie einen Computer an diesen Monitor anschließen, müssen Sie die mitgelieferten Ferritkerne anbringen. Andernfalls entspricht dieser Monitor nicht den obligatorischen FCC/IC/CEStandards (EN55022). Anbringen der Ferritkerne Bringen Sie die - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 71
Anschlußfeld 9 (D) Linkes Anschlußfeld 11 (D) Fernbedienung RM-921 12 (D) Aufstellen des Monitors 14 (D) Die versenkbaren Füße 14 (D) Vorsicht 15 (D) Anschließen des Monitors 16 (D) Anschließen des Netzkabels 16 (D) Anschlußbeispiel 17 (D) Die Bildschirmmenüs 18 (D) Arbeiten - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 72
trennen, ziehen Sie den Netzstecker aus der Netzsteckdose. Ziehen Sie nicht am Kabel. • Wenn der Monitor auf dem Boden aufgestellt wird, verwenden Sie bitte unbedingt die versenkbaren Füße. Aufstellung • Achten Sie zu dem Gerät haben, wenden Sie sich bitte an einen autorisierten Sony-Händler. 4 (D) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 73
PFM-500A2W sind 16:9Flachmonitore (42 Monitor verfügt über einen Hochleistungsbildrasterwandler. Dank eines speziellen Algorithmus kann der Monitor Signale in vielfältigen Formaten verarbeiten - Video Sony eingesetzt werden, sofern diese mit dem SIRCS-Code arbeitet. • Drei Gruppen von Video ß REMOTE ( - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 74
ßfeld Einzelheiten zum linken Anschlußfeld finden Sie unter "Linkes Anschlußfeld" auf Seite 11(D). 3 Versenkbare Füße Dienen zum Aufstellen des Monitors auf dem Boden. Näheres zu den versenkbaren Füßen finden Sie unter "Die versenkbaren Füße" auf Seite 14(D). 4 Bedienfeld Einzelheiten zum Bedienfeld - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 75
So nehmen Sie die Anschlußfeldabdeckung ab Lösen Sie die Schrauben wie in der Abbildung unten dargestellt, und nehmen Sie die Anschlußfeldabdeckung ab. Schrauben So bringen Sie die Fernbedienung in der Anschlußfeldabdeckung an Bringen Sie die Fernbedienung wie in der Abbildung unten dargestellt an - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 76
(Bereitschaft)/Anzeige u (Bereitschaft) Zum Einschalten des Monitors. Durch erneutes Drücken schalten Sie wieder in den Y/C IN eingespeisten Signals. 6 Taste LINE Zum Auswählen des über den LINE-Anschluß VIDEO IN eingespeisten Signals. 7 Taste RGB2 Zum Auswählen des Signals, das über die RGB2Anschl - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 77
Anschlußfeld RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 RGB1 IN-Anschlüsse R (R-Y)/G (Y)/B (B-Y) IN (BNC-Anschlüsse): Eingang für ein analoges RGB- oder Farbdifferenzsignal - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 78
änge für die AUDIO INBuchsen. Zum Anschließen an die Audioeingänge eines anderen Monitors oder Videogeräts. 6 Anschluß REMOTE (RS-232C) (Mini-DIN, 8polig) Mit diesem Anschluß können Sie den Monitor über das RS-232C-Protokoll fernsteuern. Näheres dazu erfahren Sie bei Ihrem autorisierten - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 79
OUT AUDIO R L 1 VARIABLE CONTROL S IN OUT 2 SPEAKERS (6-16 Ω) + + R- L 3 - SERVICE CODE 8.8. 4 5 AC IN 1 Buchsen MONITOR OUT AUDIO (L/R) (Cinchbuchsen) Zum Ausgeben der Signale, die an den Buchsen AUDIO IN eingespeist werden. Zum Anschließen an die Audioeingänge eines Audioverst - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 80
DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER SELECT !¶ ON MENU 9 !• OFF 0 ENTER !ª ON @º SET VOL CH !¡ OFF @¡ ID MODE 1 Netzschalter POWER Zum Einschalten des Monitors Anschluß VIDEO IN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 81
arbeiten und diesen Schalter statt des Netzschalters POWER 1 verwenden, werden andere Monitore, die sich bereits im Bereitschaftsmodus befinden, der Taste OFF wieder in den normalen Modus. !™ Taste DISPLAY Zum Anzeigen von Informationen zum Eingangssignal oben auf dem Monitorbildschirm. Dr - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 82
versenkbaren Füße 1 Ziehen Sie die Knöpfe heraus, und ziehen Sie die versenkbaren Füße nach unten. So stabilisieren Sie die versenkbaren Füße Wenn der Monitor auf dem Boden aufgestellt wird, müssen Sie die versenkbaren Füße stabilisieren. Bringen Sie die Halterungen für die Fußstützen wie in der - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 83
Vorsicht • Achten Sie bei der Installation des Monitors darauf, daß der Abstand größer ist als in der Abbildung unten dargestellt. • Die Umgebungstemperatur muß zwischen 0°C - +35°C betragen. Bei Verwendung der versenkbaren Füße Vorderseite Wand - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 84
Anschließen des Monitors Anschließen des Netzkabels 1 Schließen Sie das Netzkabel an die Buchse AC IN an. Bringen Sie dann den Netzsteckerhalter (mitgeliefert) am Netzkabel an. Buchse - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 85
auch in den Bedienungsanleitungen zu den anzuschließenden Geräten nach. Computer Betacam-SPVideorecorder an Audioausgang an Videoausgang an an Video- Audio- ausgang ausgang Videorecorder, Laser-DiscPlayer, Spielekonsole usw. * an R(R-Y)/G(Y)/ B(B-Y), HD/COMP, VD IN an AUDIO IN an RGB IN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 86
Die Bildschirmmenüs Arbeiten mit den Menüs Menütasten Zur Arbeit mit den Menüs stehen am Monitor und auf der Fernbedienung vier Menütasten zur Verfügung. Fernbedienung SELECT MENU Monitor MENU . > ENT ENTER Soll wieder die normale Bildschirmanzeige zu sehen sein, drücken Sie die Taste MENU - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 87
vergrößert wird, während am Monitor HDTV-Signale eingehen, schaltet der Monitor möglicherweise in den Abtastverschiebungsmodus. können den Korrekturpegel für die Konturen ändern: TIFF: Standardeinstellung für VIDEO-Signal HOCH: Standardeinstellung für Computersignal !§ H FILTER Im Normalfall sollte - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 88
über die Fernbedienung" auf Seite 32(D). @£ ERNBED ART Dient zum Auswählen des Fernbedienungsmodus. TV: Für Monitore oder Fernsehgeräte von Sony PROJ: Für Projektoren von Sony AUS: Deaktiviert die Fernbedienung. Näheres dazu finden Sie unter "Verwenden einer anderen Fernbedienung" auf Seite 33 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 89
dann immer noch angezeigt, wenden Sie sich bitte an Ihren autorisierten Sony-Händler. Wenn die Anzeige u blinkt oder NEGATIV angezeigt wird, schlagen Sie unter "Selbstdiagnosefunktion" auf Seite 31(D) nach. #º LÜFTER Dieser Monitor enthält Ventilatoren. Hier wird angegeben, ob die Ventilatoren - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 90
Auswählen des Bildes 1 Drücken Sie die Taste CTRL am Bedienfeld des Monitors. Die Tasten RGB1, YUV, RGB2, LINE und Y/C leuchten auf. 2 Wählen Audio- und Videosignal wird ausgewählt. LINE: Das über den Anschluß VIDEO IN und die Buchse AUDIO IN (LINE-Anschlüsse) eingespeiste Audio- und Videosignal - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 91
, Inc. c) VESA ist ein eingetragenes Warenzeichen der Video Electronics Standard Association. d) ATI ist ein eingetragenes Warenzeichen Informationen zum Eingangssignal jederzeit abrufen, indem Sie die Taste DISPLAY auf der Fernbedienung drücken. Die Informationsliste zum Eingangssignal Farbsystem - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 92
Y/C-Signal ausgewählt. Das Bild wird als Standbild angezeigt. Hinweis Wenn Computersignale von mehr als 100 kHz eingespeist werden und der Monitor die Signale empfangen kann, wird die Bildschirmanzeige (horizontale Frequenz) auf 99,9 kHz festgelegt. Sie können das Bild anzeigen lassen und dabei - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 93
PHASE Wählen Sie mit den Tasten >/. die Option "PHASE" aus, und drücken Sie ENT. Stellen Sie mit den Tasten >/. für die Phase einen Wert zwischen -50 (Minimum) und +50 (Maximum) ein. >: Der Grünanteil im Bild wird verstärkt. .: Der Rotanteil im Bild wird verstärkt. Hinweise • Für ein RGB-Signal kö - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 94
Einstellen von Zoom, Bildgröße und Bildposition Sie können das Bild verschieben, so daß es auf den Bildschirm paßt, bzw. Bildhöhe und Bildbreite unabhängig voneinander einstellen. Mit der Zoom-Funktion können Sie einen Bildausschnitt auf das Zwei-, Drei- oder Vierfache der ursprünglichen Größe - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 95
4 Stellen Sie den Cursor (z) mit den Tasten >/. auf "V LAGE", und drücken Sie ENT. Das folgende Menü erscheint auf dem Bildschirm. V L AGE : 00 5 Ändern Sie mit >/. die Position des Bildes. >: Das Bild verschiebt sich nach oben. .: Das Bild verschiebt sich nach unten. Die vertikale Lage des - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 96
Der Speicher Mit der Funktion SPEICHERN können Sie die aktuelle Bildeinstellung für die einzelnen Eingangssignale speichern. Die gespeicherten Einstellungen können Sie danach jederzeit abrufen. Die Optionen in den Menüs BILDEINST, BILDGRÖSSE und KONFIG (nur die Optionen ANHEBUNG und H FILTER) kö - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 97
Hinweise • Die Speichereinstellungen können nicht abgerufen werden, wenn das ausgewählte Signal nicht dem voreingestellten Signal entspricht. • Die folgenden Optionen können Sie speichern: Menü BILDEINST - KONTRAST - HELLIGKEIT - FARBE - PHASE - FARBTEMP - BILDVERST Menü BILDGRÖSSE - H GRÖSSE - H - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 98
cken Sie den Schalter u am Bedienfeld oder den Schalter POWER auf der Fernbedienung. Signalspezifikation für die Energiesparfunktion RGB1: Wenn nicht am Anschluß HD/COMP IN eingeht, schaltet sich der Monitor nicht ein, auch wenn ein Synchronisationssignal eingespeist wird. Achten Sie darauf - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 99
der blinkenden Anzeige u und der Zahlen in der Anzeige SERVICE CODE angezeigt. Die Zahlen geben Auskunft über den aktuellen Zustand des Monitors. Wenn das Gerät ordnungsgemäß arbeitet, blinkt nur der Punkt rechts unten in der Anzeige SERVICE CODE. Wenn die Anzeige u blinkt, überprüfen Sie die Nummer - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 100
: 0 0 1 FERNBED ART : TV NUR FERNBED : AUS 3 Drücken Sie ID MODE SET. Die Zeichen auf dem ausgewählten Monitor werden nun blau angezeigt, die auf den ID MODE Sie können nun einen bestimmten Monitor steuern. (Im ID-Modus stehen alle Funktionen außer 32 POWER (D) ON/OFF zur Verfügung.) 4 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 101
Modell der Fernbedienung RM-854 Einstellung der Option FERNBED ART TV Eingangswahl RGB1 RGB RGB 2 - LINE LINE1 Menütasten MENU MENU ENTER ENTER + + - - Bildeinstellung Kontrast CONTRAST+/- Farbe CHROMA+/- Phase PHASE+/- Bildschirminformationen DISPLAY RM-1271 PJ A B VIDEO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 102
horizontal) × 518 (vertikal) mm Bildschirmgröße 42 Zoll, Diagonale 1.056 mm Eingänge hohe Impedanz LINE (NTSC, PAL) VIDEO IN BNC-Anschluß (×1) FBAS-Videosignal, Mittelwert, hohe Impedanz VIDEO OUT BNC-Durchschleifanschluß Cinch-Durchschleifanschlüsse (×2) MONITOR OUT AUDIO (L, R) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 103
SPEAKERS 6 bis 16 Ohm, 7 W + 7 W (bei Impedanz von 8 Ohm) Allgemeines Betriebsspannung 100 bis 120 V Wechselstrom, tzen (2) Schrauben für Halterungen für Fußstützen (6) Stabilisatoren für Monitor (2) Bedienungsanleitung (1) Änderungen, die dem technischen Fortschritt dienen, bleiben vorbehalten - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 104
tomar las medidas adecuadas. Para los usuarios del modelo PFM-500A2WE ESTE APARATO DEBE CONECTARSE A TIERRA IMPORTANTE Los conductores de Nota Al conectar un ordenador a este monitor, instale los núcleos de ferrita suministrados. En caso contrario, el monitor no cumplirá las normas FCC/IC/CE - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 105
controles 6 (ES) Parte frontal / Laterales 6 (ES) Panel de control 8 (ES) Panel de conectores derecho 9 (ES) Panel de conectores izquierdo 11 ES) Visualización de información sobre la señal de entrada y el estado del monitor 22 (ES) Ajuste de la imagen 24 (ES) ES Español Ajuste del - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 106
plasma) • Es posible que aparezcan pequeños puntos negros y/o brillantes en el PDP. Esto es normal. • No muestre la misma imagen fija en la pantalla durante mucho tiempo consecutivo. La imagen residual puede aparecer en parte de un panel, puesto que el brillo de esa parte Sony autorizado. 4 (ES) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 107
la serie PFM-500A2W son monitores de 16:9 de panel plano de 42 pulgadas. Éstos están equipados con el panel PDP (Plasma Display Panel) y ID • Menú en pantalla para realizar distintos ajustes • Conector Control-S • Conector REMOTE (RS-232C) (mini DIN de 8 pines) Advertencia sobre la conexión de - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 108
abrir la cubierta del panel, consulte la parte derecha de esta página. 2 Panel de conectores izquierdo Para obtener más información sobre el panel de conectores izquierdo, consulte "Panel de conectores izquierdo" en la página 11(ES). 3 Pies replegables Utilícelos para colocar el monitor en el suelo - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 109
tal como se muestra en la siguiente ilustración y retire la cubierta del panel. Tornillos Para instalar el mando a distancia en la cubierta del panel Instale el mando a distancia en la parte posterior de la cubierta del panel izquierdo, tal como se ilustra a continuación. Mando a distancia Nota Al - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 110
Panel de control VOL - VOL + MENU . > ENT RGB1 YUV RGB2 LINE Y/C CTRL u !£ !™ !¡ 0 98765 4 32 1 1 Detector de control remoto Recibe el haz del mando a distancia. 2 Interruptor u (de espera) / indicador u (de espera) Pulse este interruptor para encender el monitor conector VIDEO IN de - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 111
Panel de conectores derecho RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 Conectores RGB1 IN R (R-Y)/G (Y)/B (B-Y) IN (tipo BNC): Introduzca la señal RVB o de componente aná - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 112
VIDEO IN o Y/C IN se emite desde el conector VIDEO OUT o la toma Y/C OUT. VIDEO OUT (tipo BNC): Conéctelo a la entrada de señal de vídeo compuesta de otro monitor monitor o equipo de vídeo. 6 Conector REMOTE (RS-232C) (mini DIN de 8 pines) Este conector permite realizar el control remoto del monitor - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 113
Panel de conectores izquierdo MONITOR OUT AUDIO R L 1 VARIABLE CONTROL S IN OUT 2 SPEAKERS (6-16 Ω) + + R- L 3 - SERVICE CODE 8.8. 4 5 AC IN 1 Tomas MONITOR OUT AUDIO (L/R) (tipo fonográfico) Genere la salida de la señal introducida mediante las tomas AUDIO IN. Conéctelas a las - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 114
DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER SELECT !¶ ON MENU 9 !• OFF 0 ENTER !ª ON @º SET VOL CH !¡ OFF @¡ ID MODE 1 Interruptor POWER Púlselo para encender el monitor conector VIDEO IN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 115
ón SET. Después de realizar esta operación, pulse el botón OFF para volver al modo normal. !™ Botón DISPLAY Muestra información sobre la señal de entrada en la parte superior de la pantalla del monitor. Pulse este botón de nuevo para borrarla. !£ Botón YUV Permite seleccionar la señal de componente - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 116
Instalación Uso de los pies replegables 1 Agarre los tiradores y extraiga los pies replegables. Para fijar los pies replegables Si instala la unidad en el suelo, asegúrese de fijar los pies replegables. Instale los soportes de apoyo de los pies como se ilustra a continuación. 2 Gire los pies - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 117
Precaución • Cuando instale el monitor, compruebe que haya más espacio que el mostrado en la siguiente ilustración. • Pared 25 (9 7/8) Pared Compruebe que la sección de control se encuentre en la parte inferior. Lateral ,,,,, 10(4) Pared 5 (2) Pared Unidades: cm (pulgadas) 25 (9 7/8) Pared 15 ( - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 118
se conecte a la cubierta de la toma AC IN. Cubierta de la toma AC IN Para retirar el cable de alimentación de CA Comprima las partes superior e inferior y extraiga el portaenchufe de CA. 16 (ES) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 119
cable, tire del enchufe, nunca del propio cable. • Lea el manual de instrucciones del equipo que vaya a conectar. Ordenador Videograbadora Betacam SP HD/COMP, VD IN a AUDIO IN a RGB IN a salida de vídeo a Y/C o VIDEO IN a salida de audio a AUDIO IN a salida de señal componente o RVB RGB - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 120
Mando a distancia SELECT MENU Monitor MENU . > ENT ENTER Menú guía Nota "- - - -" aparece junto a las opciones cuando la función no está disponible. La disponibilidad depende del tipo de señal de entrada. Menú CONTROL IMAG En este manual, se utilizan los botones del panel de control en los - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 121
de corrección del contorno: BAJO: Ajuste por omisión para la señal de VIDEO ALTO: Ajuste por omisión para la señal de ordenador !§ FILTRO H Seleccione información sobre la señal de entrada en la parte superior de la pantalla del monitor durante unos cinco segundos, al activar la alimentación o cambiar - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 122
modo de mando a distancia. TV: Mando a distancia de monitores o televisores Sony. PROY: Mando a distancia de proyectores Sony. DES: Desactiva el control remoto monitor, de modo que éste sólo puede controlarse con el mando a distancia. Mientras SOLO REMOTO está ACT, se apagan los indicadores del panel - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 123
del panel de control también parpadea. Nota El mensaje "TEMPERATURA MAL" puede aparecer cuando se bloquean los orificios de ventilación o cuando el monitor se e instale el monitor en un lugar bien ventilado. Si el mensaje sigue apareciendo, póngase en contacto con un proveedor Sony autorizado. Si - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 124
la imagen 1 Pulse CTRL en el panel de control del monitor. Se iluminan los botones RGB1, YUV, ñal de audio y vídeo introducida desde el conector VIDEO IN y la toma AUDIO IN de los conectores LINE la indicación "FIJA" en la parte superior del monitor. Para borrar la indicación, ajuste VER MENU en - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 125
el paso 4 anterior. Nota Pulsando el botón DISPLAY del mando a distancia puede obtener información sobre es una marca comercial registrada de Video Electronics Standard Association. d) ATI es IN. Indicaciones en pantalla sobre el estado del monitor Indicaciones Significado en pantalla 31.5kHz / La - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 126
memoria los niveles ajustados. Ajuste del contraste, brillo, crominancia y fase Pulse MENU para que aparezca el menú principal en la pantalla del monitor y seleccione la opción "CONTRASTE", "BRILLO", "CROMA" o "FASE" en el menú CONTROL IMAG con los botones >/.. CONTRASTE >: para que el conjunto de - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 127
3 Pulse >/. para desplazar el cursor (z) hasta "GANANC. AUTO" y pulse ENT. Aparece el siguiente menú en la pantalla del monitor. GANANC . AUTO : DES 4 Pulse >/. para ajustar "GANANC. AUTO" en ACT. 5 Pulse ENT. Vuelve a aparecer el menú CONTROL IMAG. Restauración de los valores originales del men - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 128
ño de la imagen. >: para aumentar el tamaño vertical .: para reducir el tamaño vertical El tamaño vertical de la imagen se indica en la pantalla del monitor en un rango comprendido entre MIN(-50) y MAX(+50). El valor de fábrica es 00. 8 Pulse ENT. Vuelve a aparecer el menú TAMAÑO IMAGEN. Ajuste de - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 129
. >: para desplazar la imagen hacia arriba .: para desplazar la imagen hacia abajo La posición vertical de la imagen se indica en la pantalla del monitor en un rango comprendido entre MIN(-50) y MAX(+50). El valor de fábrica es 00. 6 Pulse ENT. Vuelve a aparecer el menú TAMAÑO IMAGEN. Ampliaci - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 130
cinco señales de entrada. Almacenamiento de la condición actual 1 Pulse MENU. Aparece el menú principal en la pantalla del monitor. MENU PPA L . CONTROL I MAG T AMAÑO IMAGEN CONF I G MEMOR I A R EMO T O ES T ADO S E L E C ENTER A N U L A R MENU 2 Pulse >/. para desplazar el cursor (z) hasta - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 131
Notas • No es posible recuperar los datos de la memoria si la señal seleccionada difiere de la predefinida. • Es posible memorizar las siguientes opciones: Menú CONTROL IMAG - CONTRASTE - BRILLO - CROMA - FASE - TEMP COLOR - GANANC. AUTO Menú TAMAÑO IMAGEN - TAMAÑO H - DESPLAZ H - TAMAÑO V - DESPLAZ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 132
ENT. Aparece el siguiente menú en la pantalla del monitor. AHORRO ENERG : 5m Para cancelar la función de ahorro de energía • Vuelva a introducir la señal de sincronización. • Pulse el interruptor u en el panel de control o el interruptor POWER del mando a distancia. Especificación de señales para - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 133
meros informan sobre el estado actual del monitor. Cuando la unidad funciona correctamente, sólo parpadea el punto situado en la parte derecha inferior del indicador SERVICE CODE. Si parpadea el indicador u, compruebe el número y consulte a un proveedor Sony autorizado. 1 Verifique el número de dos - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 134
monitor especificado (todas las operaciones están disponibles en el modo ID excepto POWER ON/OFF). 32 (ES) 4 Después de realizar los ajustes necesarios, pulse ID MODE OFF. El monitor menú REMOTO aparece en la pantalla del monitor. R EMO T O NUM I ND : 001 MODO R EMO T O : TV SO L O R EMO T O : - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 135
• Activación y desactivación de indicaciones en pantalla (sólo para monitores de vídeo y televisores) Las operaciones disponibles y los botones TV RGB - LINE1 MENU ENTER + - CONTRAST+/- CHROMA+/- PHASE+/- DISPLAY RM-1271 PJ A B VIDEO PAGE o ? / > . CONTR+/- COLOR+/- HUE+/- - RM-PJ1292 PJ A B VIDEO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 136
OUT (L, R) (Salida variable) Toma fonográfica (×2) Derivada MONITOR OUT AUDIO (L, R) Toma fonográfica (×2) Máximo 500 mVrms, alta impedancia CONTROL S (IN, OUT) Minitoma (estéreo) (×2) 5 Vp-p REMOTE (RS-232C) Mini DIN de 8 pines SPEAKERS 6 a 16 ohmios, 7 W + 7 W (cuando la impedancia es - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 137
de ferrita (2) Soporte de apoyo de los pies (2) Tornillos para el soporte de apoyo de los pies (6) Estabilizador del monitor (2) Manual de instrucciones (1) Diseño y especificaciones sujetos a cambios sin previo aviso. Asignación de pines Toma Y/C (mini DIN de 4 pines) Crominancia Luminancia - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 138
che l'utilizzatore adotti gli accorgimenti adeguati. Per gli utenti di PFM-500A2WE QUESTO APPARECCHIO DEVE ESSERE COLLEGATO A MASSA IMPORTANTE I fili di Quando si collega il monitor ad un computer, installare i nuclei di ferrite in dotazione. In caso contrario il monitor non sarà conforme agli - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 139
(I) Posizione e funzione delle parti e dei comandi ......... 6 (I) Parte anteriore / Parti laterali 6 (I) Pannello di controllo 8 (I) Pannello fermo immagine 22 (I) Visualizzazione delle informazioni relative allo stato del monitor e al segnale di ingresso 22 (I) Regolazione dell'immagine - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 140
PDP (Plasma Display Panel) • Sul PDP potrebbero apparire dei puntini neri e/o dei punti luminosi che sono del tutto normali. • Non visualizzare lo stesso fermo immagine sullo schermo per un lungo periodo continuato. Altrimenti l'immagine persistente potrebbe apparire su una parte - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 141
Caratteristiche I monitor della serie PFM-500A2W sono monitor a pannello piatto formato 16:9 da 42 pollici; questi monitor utilizzano il pannello PDP (Plasma Display Panel, pannello al plasma) e accettano vari tipi di segnali grazie al convertitore di scansione incorporato. Migliore qualità dell' - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 142
dei connettori sinistro. È possibile installare il telecomando nella parte posteriore del coperchio. Per maggiori informazioni sull'apertura del " a pagina 11 (I). 3 Piedi estraibili Da usare per sistemare il monitor sul pavimento. Per maggiori informazioni sull'uso dei piedi estraibili, vedere la - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 143
pannello Installare il telecomando nel retro del coperchio del pannello sinistro come illustrato qui sotto. Telecomando Nota Quando si alloggia il telecomando, accertarsi che la parte superiore del telecomando sia rivolta verso l'alto e il retro sia rivolto verso l'esterno. 7 (I) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 144
telecomando. 2 Interruttore u (attesa)/Indicatore u (attesa) Premere per accendere il monitor. Premere di nuovo per tornare al modo di attesa. Nel modo di attesa 6 Tasto LINE Per selezionare l'ingresso del segnale dal connettore VIDEO IN nei connettori LINE. 7 Tasto RGB2 Per selezionare l'ingresso - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 145
dei connettori destro RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 Connettori RGB1 IN R (R-Y)/G (Y)/B (B-Y) IN (tipo BNC): immettono il segnale RGB analogico o il segnale - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 146
(Y/B-Y/R-Y) di un altro monitor. HD/COMP OUT ( composito di un altro monitor. VD OUT (tipo un monitor con un un altro monitor. 5 Connettori monitor o di un'altra apparecchiatura video. 6 Connettore REMOTE (RS-232C) (mini DIN a 8 piedini) Questo connettore consente di controllare il monitor - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 147
VARIABLE CONTROL S IN OUT 2 SPEAKERS (6-16 Ω) + + R- L 3 - SERVICE CODE 8.8. 4 5 AC IN 1 Prese MONITOR OUT AUDIO (L/R) (tipo fono) prese) Collegare alle prese CONTROL S dell'apparecchiatura video o di altri monitor. Sarà così possibile controllare contemporaneamente tutte le - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 148
DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER SELECT !¶ ON MENU 9 !• OFF 0 ENTER !ª ON @º SET VOL CH !¡ OFF @¡ ID MODE 1 Interruttore POWER Premere per accendere il monitor connettore VIDEO IN - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 149
SET. Terminata l'operazione premere il tasto OFF per tornare al modo normale. !™ Tasto DISPLAY Per visualizzare le informazioni relative al segnale di ingresso nella parte superiore dello schermo del monitor. Premere di nuovo per annullare le informazioni. !£ Tasto YUV Per selezionare l'ingresso del - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 150
Installazione Uso dei piedi estraibili 1 Tirare le manopole e tirare verso il basso i piedi estraibili. Per fissare i piedi estraibili Quando l'apparecchio è installato sul pavimento, fissare i piedi estraibili. Installare le staffe supporto piedi come illustrato sotto. 2 Girare i piedi - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 151
Precauzioni • Quando si installa il monitor, assicurarsi che vi sia più spazio di quello indicato nella figura in basso. • La temperatura ambiente deve essere 25 Muro Muro 20 25 Muro Assicurarsi che la sezione dei comandi sia nella parte inferiore. Laterale ,,,,,10 Muro 5 Muro Unità: cm 15 (I) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 152
Collegamenti Collegamento del cavo di alimentazione CA 1 Inserire il cavo di alimentazione nella presa AC IN. Quindi installare il fermaspina CA (in dotazione) sul cavo di alimentazione CA. Presa AC IN Cavo di alimentazione CA Ferma spina CA 2 Far scorrere il fermaspina CA sul cavo fino a - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 153
preliminari • Accertarsi innanzitutto che l'alimentazione in ogni parte dell'apparecchiatura sia disattivata. • Utilizzare cavi di il manuale delle istruzioni dell'apparecchiatura da collegare. Computer Videoregistratore Betacam SP all'uscita audio all'uscita video all'uscita all'uscita video - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 154
di funzionamento dei menu Per il funzionamento dei menu sono disponibili quattro tasti sul monitor e sul telecomando. Telecomando SELECT MENU Monitor MENU . > ENT ENTER Per le spiegazioni in questo manuale vengono usati i tasti sul pannello di controllo. Il tasto ENTER sul telecomando svolge - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 155
Nota Non ingrandire l'immagine mentre il monitor riceve i segnali HDTV, ciò potrebbe fare entrare il monitor nel modo di campionamento offset e l'immagine correzione del contorno: LOW: Impostazione predefinita per il segnale VIDEO HIGH: Impostazione predefinita per il segnale del computer !§ FILTRO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 156
nella parte superiore dello schermo del monitor, quando viene attivata l'alimentazione o commutato il segnale di ingresso. !• POWER SAVE MODO TELEC Selezionare il modo telecomando. TV: telecomando di monitor o TV Sony PROI: telecomando di proiettori Sony NO: per disattivare il telecomando Per - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 157
caso verificare che le prese di ventilazione non siano ostruite e installare il monitor in un luogo ben ventilato. Se il messaggio continua ad essere visualizzato, rivolgersi al rivenditore autorizzato Sony locale. Quando l'indicatore u lampeggia oppure appare NG, vedere la sezione "Funzione di - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 158
(I) Nota Si consiglia di utilizzare come sorgente di ingresso un'apparecchiatura video dotata di TBC (time base corrector). Se si riceve un segnale MENU SCHERMO nel menu CONFIG viene impostata su SI, sulla parte superiore del monitor appare la videata "PAUSA". Per annullare la videata, impostare - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 159
di ingresso in qualsiasi momento premendo il tasto DISPLAY sul telecomando, indipendentemente dalle impostazioni sopra descritte. Y/C L'ingresso video Y/C è selezionato su LINE. PAUSA L'immagine è ferma. Nota Se vengono immessi segnali al computer maggiori di 100 kHz e se il monitor riceve i - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 160
G MEMOR I A T E L E COMA ND STATO S E L ENTER A N N U L L A MENU 2 Premere >/. per spostare il cursore (z) su "CTRL IMMAG" e premere ENT. Sullo schermo del monitor appare il menu CTRL IMMAG. C T R L I MMA G CONTRAS TO : 80 L UM I NOS I T À : 00 CO L OR E : 00 FASE : 00 T EMP COLORE - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 161
del menu CTRL IMMAG 1 Nel menu CTRL IMMAG, premere >/. per spostare il cursore (z) su "RIPRISTINA" e premere ENT. Sullo schermo del monitor appare il menu seguente. R I PR I ST I NA : NO S E L ENTER A N N U L L A MENU 2 Premere >/.. L'impostazione "NO" passa su "SI". R I PR I ST I NA : SI - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 162
'immagine. >: per aumentare la dimensione verticale .: per ridurre la dimensione verticale La dimensione verticale dell'immagine viene indicata sullo schermo del monitor da MIN(-50) a MAX(+50). Il valore di fabbrica è 00. 8 Premere ENT. Si tornerà al menu DIMEN IMMAG. Regolazione della posizione - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 163
3 Premere ENT. Si tornerà al menu DIMEN IMMAG. 4 Premere >/. per spostare il cursore (z) su "SPOST VERT" e premere ENT. Sullo schermo del monitor appare il menu seguente. SPOST VERT : 00 Ripristino delle dimensioni e della posizione originali dell'immagine 1 Nel menu DIMEN IMMAG, premere >/. per - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 164
Richiamo delle condizioni memorizzate 1 Nel menu MEMORIA, premere >/. per spostare il cursore (z) su "CARICA" e premere ENT. Sullo schermo del monitor appare il menu seguente. CAR I CA MEM 1 : RGB 3 1 . 5 kHz 6 0 Hz MEM 2 : VUOT A MEM 3 : VUOT A MEM 4 : VUOT A MEM 5 : VUOT A S E L ENTER - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 165
Note • Non è possibile richiamare i dati della memoria se il segnale selezionato è differente dal segnale preimpostato. • È possibile memorizzare le seguenti voci: Menu CTRL IMMAG - CONTRASTO - LUMINOSITÀ - COLORE - FASE - TEMP COLORE - AGC IMMAGINE Menu DIMEN IMMAG - DIMENSIONE O - SPOST ORIZZ. - - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 166
S CH E RMO : SI P OWE R S A V E : 5M I N . L I NGUA S E L ENTER A N N U L L A MENU 3 Premere >/. per spostare il cursore (z) su "POWER SAVE" e premere ENT. Sullo schermo del monitor appare il menu seguente. P OWE R S A V E : 5M I N . 4 Premere >/. per selezionare il periodo per entrare nel - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 167
sulle condizioni correnti del monitor. Quando l'apparecchio funziona correttamente, lampeggia solo il punto sull'indicatore SERVICE CODE nella posizione in basso a destra. Se lampeggia l'indicatore u, verificare il numero e rivolgersi al rivenditore autorizzato Sony locale. 1 Verificare il numero - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 168
001 : TV : NO 3 Premere ID MODE SET. Il carattere sul monitor selezionato diventa di colore ciano mentre gli altri diventano di colore rosso. ON SET OFF ID MODE È possibile far funzionare solo un monitor specificato. (Nel modo ID sono possibili tutte le operazioni eccetto quelle di POWER ON/OFF - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 169
(solo per monitor e televisori) Le REMOTE MODE Selezione ingresso RGB1 RGB 2 LINE Funzionamento da MENU menu ENTER + - Regolazione immagine Contrasto Colore Fase Indicazioni a schermo RM-854 TV RGB - LINE1 MENU ENTER + - CONTRAST+/- CHROMA+/- PHASE+/- DISPLAY RM-1271 PJ A B VIDEO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 170
Ingresso: 12 formati (Vedere a pagina 23 (I)) Memoria video 1.152 × 1.152 × 24 bit (totale RGB) Valore di campionamento fase di compensazione da 14,3 a 50 MHz massimo (equivalente a campionamento di 100 MHz) Pannello Plasma Display Panel tipo AC Risoluzione dello schermo 852 punti × 480 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 171
× 636 × 152 mm (l/a/p) Peso 45 kg Accessori in dotazione Cavo di alimentazione CA (1) Fermaspina CA staffa supporto piedi (6) Stabilizzatore del monitor (2) Istruzioni per l'uso (1) 8 9 10 11 12 13 14 15 Segnale Video rosso o R-Y Video verde o Y Video blu o B-Y Terra Terra Terra rosso Terra verde - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 172
ࠂܯ u 1 / 2 Λൈ͘ɻ 3 ҙ ҙ Րࡂ ిײ 7 2 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 173
࣍ 4ʢJʣ 6ʢJ 8ʢJʣ 9ʢJʣ 9ʢJʣ 10ʢJʣ 3 19ʢJʣ 21ʢJʣ 23ʢJʣ 27ʢJʣ 29ʢJʣ J ຊ 31ʢJʣ 33ʢJʣ 35ʢJʣ 36ʢJʣ 36ʢJʣ 37ʢJʣ 38ʢJʣ 39ʢJʣ 40ʢJʣ 3 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 174
੍ڧ 4 (J) 7 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 175
ࢭې n Ξʔεઢ 5 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 176
ࢭې 6 (J) ࢭې 2 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 177
ࢭې 2 7 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 178
ࠂܯ ͍͞ɻ ҙ 8 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 179
PDP ಛ 1%1 1%1 57ɺ1 L 54 1 4*3$4 3 3(# 57 8JOEPXT 1O1 4 3&.05& 34$ ʣ8JOEPXT 9 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 180
ࠨଆ໘ લ໘ 1 ӈଆ໘ 6 2 3 4 5 1 2 3 4 5 6 10 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 181
11 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 182
VOL - VOL + MENU . > ENT RGB1 YUV RGB2 LINE Y/C CTRL u !£ !™ !¡ 0 98765 4 32 1 1 2 u u u u 3 6 LINEϘλϯ -*/&ࢠͷ7*%&0 7 RGB2Ϙλϯ 3 8 YUVϘλϯ 3 9 RGB1Ϙλϯ 3 3 0 ENT 4 CTRL u 2 5 Y/CϘλϯ z !™ MENU !£ VOL 12 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 183
RGB 1 IN OUT R R-Y G Y B B-Y 1 HD/ 4 COMP SYNC VD L AUDIO R RGB 2 RGB IN L 2 AUDIO IN R VIDEO Y/C 3 5 L AUDIO R IN OUT LINE 6 REMOTE (RS-232C) 1 RGB1 INʢRGB1 RʢR-Yʣ/GʢYʣ/BʢB-YʣINʢRGB BNC 3 3 3 1#13 1 13 ৴߸Λ 3ʢ3 HD/COMP IN BNC VD IN BNC ೖྗࢠ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 184
OUTʢRGB BNC 3 3 3 HD/COMP OUT BNC 0.1 VD OUT BNC 7%*/ ࢠ ͝ҙ )%$0.1065ࢠͱ7%065 AUDIO OUT L/R 6%*0 */-3 5 LINE OUT 3 7*%&0ɺ:$ 065 7*%&0 VIDEO OUT BNC Y/C OUT DIN4 AUDIO OUT L/R 6%*0 */-3 6 REMOTE(RS-232C DIN8ϐϯʣ 34 14 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 185
L 1 VARIABLE CONTROL S IN OUT 2 SPEAKERS (6-16 Ω) + + R- L 3 - SERVICE CODE 8.8. 4 5 AC IN 1 MONITOR OUT AUDIOʢL/R 6%*0 N7SNT 2 CONTROL S IN/OUT S 0/530-4 0/530-4065 0/530-4 0/530-4 3 SPEAKERS L/R 4 SERVICE CODE 5 ⁄AC IN u 15 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 186
RM-921 1 !™ MUTING DISPLAY POWER 2 3 RGB1 RGB2 YUV !£ 4 LINE Y/C MTS/MPX !¢ 5 123 6 456 789 10/0 CH !∞ 7 STILL ZOOM DEGAUSS 8 !§ POWER ON SELECT MENU !¶ 9 !• OFF 0 ENTER !ª ON @º SET VOL CH !¡ OFF @¡ ID MODE 1 POWER 2 MUTINGϘλϯ 65 70 3 RGB1/ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 187
0 POWER OFFεΠον 108&3εΠον1 !¡ ID MODEʢON/SET/OFFʣϘλϯ 0 4&5 0 ୯ 3 2ݸ } ] ] } !™ DISPLAYϘλϯ !£ YUVϘλϯ 3 !¢ MTS/MPXϘλϯ !∞ CHϘλϯ !§ DEGAUSS !¶ SELECT z u 0/530-4 !• MENU !ª ENTER @º VOL @¡ CHʴ/ʵϘλϯ 17 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 188
18 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 189
ઃஔ ࠂܯ ੍ڧ 3 1 2 ࠂܯ 19 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 190
ઃஔ લ໘ น 20 น 10 10 น ଆ໘ ,,,3.5 น લ໘ น 10 ୯Ґ: cm ଆ໘ চ 2.5 5.5 ,,น ,,,,,,চ ୯Ґ: cm લ໘ น 25 น 10 10 น 25 น 20 น 25 น 10 ଆ໘ ,,,,,น 5 น ୯Ґ: cm 20 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 191
ଓ 1 AC IN ιέοτ ACϓ ϥ ά ϗϧμʔ 1 2 2 AC IN 21 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 192
HD/COMPɺVD IN ө૾ ग़ྗ AUDIO IN RGB IN Y/C·ͨ VIDEO IN AUDIO IN ʢ·ͨ RGBʣ৴ ߸ग़ྗ RGB 1 IN OUT R R-Y G Y B B-Y HD/ COMP VD SYNC L AUDIO R RGB 2 RGB IN L AUDIO IN R VIDEO Y/C L AUDIO R IN OUT LINE * RʢR-Yʣ/GʢYʣ/ BʢB-YʣIN AUDIO IN AUDIO - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 193
SELECT MENU MENU . > ENT ENTER 5&3 5 Ϙλϯ ͱɺ4&-&$5 1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU PIC CONTROLϝχϡʔ 1 P I C CONTROL 2 CONTRAS T : 80 3 BR I GHTNESS : - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 194
!ª S E L E C T ENTER C A N C E L MENU 8 H SIZE 9 H SHIFT 0 V SIZE 57 !¡ V SHIFT !™ ZOOMʢζʔϜʣ 57 !£ ASPECT !¢ RESETʢϦηοτʣ 1*$4 8 !∞ ENHANCEʢӶʣ 7*%&0 08 !§ H FILTER ௨ৗ "650 08 !¶ DISPLAY 0 !• POWER SAVE !ª LANGUAGE 24 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 195
F F S E L E C T ENTER C A N C E L MENU S E L E C T ENTER C A N C E L MENU @º LOAD @¡ SAVE @™ INDEX NO @£ REMOTE MODE TV 57 PJ OFF @¢ REMOTE ONLY ʮ3&.05&0/-:ʯΛ0 3&.05&0/-:ʯ͕ 0 3&.05& 0 3&.05&0/-:ʯΛ 0 u 53 3&.05&0 3&.05&0 25 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 196
STATUSϝχϡʔ @∞ STATUS @§ [ P FM - 5 0 0 A 2WJ ] @¶ SER I AL No . OPERA T I ON : 2000001 : 000000H @• SO F TWA R E : Ver 1 . 0 0 @ª T EMPERA TURE : FAN : OK OK #º #º FAN OK NGɿҟৗ࣌ u @§ SERIAL No @¶ OPERATION 01&3"5*0 u @• SOFTWARE @ª - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 197
0 41-":ʯΛ 0 ͍͞ɻ 1 53 3(#ɺ:67ɺ3 2 RGB1: 3 3(# ৴ YUV: 3 RGB2: 3 ߹ɻ LINE 7*%&0 Y/C PAL L I NE · Y / C 45 45 45 0 41-":ʯΛ0 45 41-":ʯΛ 0 1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 198
3 41 5 D I SPLAY : ON 4 41-":ʯΛ0''ʹ͠ɺ&/5 ϘλϯΛ ৴߸໊শ /54$ /54$ 1"- 1"- 7("B L)[ )[ 7(" ςΩετ L)[ )[ )%57 L)[ )[ .BDC L)[ )[ 7&4"D L)[ )[ 7&4 L)[ )[ .BD Ϟʔυ L)[ )[ "5*E L)[ )[ .BD Ϟʔυ L)[ )[ - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 199
1)"4 5 9 .&/6 1*$$0/530 0/53"45ʯɺ ʮ#3*()5/&44ʯɺʮ$)30."ʯɺʮ1)"4 ίϯτϥετ 0/53"45 5 9 ͝ҙ • 3 Μɻ • 1 54$ɺ1 ͱ͖ɺʮ$)30."ʯͱʮ1)"4&ʯʢ/54 54$ɺ1 54$ɺ1 3*()5/&44 5 9 30 5 9 ʢϐΫνϟʔAGC 1 .&/6 MA I N MENU P I C CONTROL P I C - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 200
2 1*$$0/530 5 Ϙλϯ Λԡ͢ɻ 1*$$0/530 P I C CONTROL CONTRAS T BR I GHTNESS C H R OM A PHASE COLOR T EMP P I CTURE AGC RESET S E L E C T ENTER : 80 : 00 : 00 : 00 : H I GH : ON C A N C E L MENU 1 1*$$0/530 3&4&5ʯΛબ ͼɺ&/5 RESET : NO 3 1*$563 5 ϘλϯΛԡ P I CTURE AGC : - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 201
1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU 2 1*$4 5 ϘλϯΛԡ ͢ɻ 1*$4 P I C S I ZE H S I ZE H SH I FT V S I ZE V SH I FT Z OOM ASPECT RESET S E L E C T ENTER : 00 : 00 : 00 : 00 : x1 : 4x3 C A - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 202
3 &/5 1*$4 4 74)*'5 5 V SH I FT : 00 2 ʷ 1 2 3 4 3 &/5 1*$4 5 5 9 6 &/5 1*$4 1 1*$4 3&4&5ʯΛબͼɺ &/5 RESET : NO S E L E C T ENTER C A N C E L MENU 00 2 ද͕ࣔ :&4 RESET : YES 1 1*$4 00.ʯΛબͼɺ &/5 S E L E C T ENTER C A N C - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 203
1*$ $0/530 1*$ 4 0 5&3 4 5 0.1-&5 1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU 2 03 5 ϘλϯΛԡ ͢ɻ .&.03 MEMOR Y LOAD SAVE S E L E C T ENTER C A N C E L MENU SAVE MEM MEM MEM MEM MEM 1 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 204
PIC CONTROLϝχϡʔ ɹ$0/53"45 ɹ#3*()5/&44 ɹ$)30." ɹ1)"4& ɹ$0-035&.1 ɹ1*$563&"($ PIC SIZEϝχϡʔ ɹ)4*;& ɹ)4)*'5 ɹ74*;& ɹ74)*'5 ɹ;00. ɹ"41&$5 CONFIG ϝχϡʔ 5&3 34 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 205
3(#·ͨ 3 1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU 2 0 5 $0 CONF I G ENHANCE H F I L TER D I SPLAY P OWE R S A V E L ANGUAGE : H I GH : AUTO : ON : 5m S E L E C T ENTER C A N C E L MENU 3 108 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 206
1 .&/6 MA I N MENU P I C CONTROL P I C S I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU 2 0 5 $0 u 4&37*$&$0 4&37*$& $0 u 1 4&37*$&$0 CONF I G ENHANCE H F I L TER D I SPLAY P OWE R S A V E L ANGUAGE : H I GH : AUTO : ON : - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 207
I ZE CONF I G MEMOR Y R EMO T E STATUS S E L E C T ENTER C A N C E L MENU 2 >.ϘλϯͰ3&.05 5 3&.05 R EMO T E I NDEX NO . : 001 R EMO T E MOD E : TV R EMO T E ON L Y : O F F S E L E C T ENTER C A N C E L MENU 3 9/0 5 I NDEX NO . : 001 OFF ID MODE 4 5 3&.05 37 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 208
REMOTE MODE ͷઃఆ 3(# 3(# -*/& .&/6 &/5&3 ʴ ʵ ίϯτϥετ ৭ͷೱ͞ ৭૬ ը໘දࣔ RM-854 TV 3 6 &/5&3 ʴ ʵ $0/53"45 ʴ ʵ $)30." ʴ ʵ 1)"4& ʴ ʵ %*41-": RM-1271 PJ " # 7*%&0 1 0/53 ʴ ʵ $0-03 ʴ ʵ )6& ʴ ʵ ʵ RM-PJ1292 PJ " # 7*%&0 1 0/53 ʴ ʵ $0-03 ʴ ʵ )6& ʴ ʵ 45" - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 209
༷ L)[ 3(# શମʣ ύωϧํࣜ ղ૾ NN NN ը໘αΠζ NNʣ ೖग़ྗ RGB1 3ʢ3 7QQ 7QQ 4:/$*/ʢ)%$0.1ɺ7 TZOD 7TZODɺ ʙ 7QQ "6%*0*/ʢ-ɺ3 N7SNT 3ʢ3 065 4:/$065ʢ)%$0.1ɺ7 TZOD 7TZOD "6%*0065ʢ-ɺ3 RGB2 3(#*/ %TVC "6%*0*/ʢ-ɺ3 - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 210
༷ ଐ 3 ϐϯྻ Y/CࢠʢϛχDIN 4ϐϯʣ ΫϩϚ৴߸ ً৴߸ RGB INࢠʢD-sub 15ϐϯʣ ϐϯNo. 3 (/% (/% 4 4$- อূॻ 40 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 211
41 (J) - Sony PFM-500A2WU | Operating Instructions (primary manual) - Page 212
ʮSony online Printed on recycled paper Sony Corporation Printed in Japan
3-866-789-
02
(1)
Operating Instructions
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Istruzioni per l’uso
EN
F
D
ES
I
J
この取扱説明書には、事故を防ぐための重要な注意事項と製品の取り扱
いかたを示しています。
この取扱説明書をよくお読みのうえ
、製品を安
全にお使いください。お読みになったあとは、いつでも見られるところ
に必ず保管してください。
お買い上げいただきありがとうございます。
警告
電気製品は安全のための注意事項を守らないと、
火災や人身事故になることがあります。
取扱説明書
PFM-500A2WU
PFM-500A2WE
PFM-500A2WJ
Flat Panel Monitor
1999 by Sony Corporation