Sony SRG-A40 Users Guide - RM-IP Setup Tool Guide

Sony SRG-A40 Manual

Get Sony SRG-A40 PDF manuals and user guides View all Sony SRG-A40 manuals
Add to My Manuals
Save this manual to your list of manuals

Sony SRG-A40 manual content summary:

  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 1
    C-499-100-12 (1) Remote Controller Setup software RM-IP Setup Tool guide Software Version 1.1 © 2017 Sony Corporation
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 2
    Firewall 11 When using Windows 7 11 When using Windows 8.1 or Windows 10 .......12 NOTICE TO USERS © 2017 Sony Corporation. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 3
    Tool setup software for configuring Sony remote controllers and cameras that support the VISCA over IP protocol connected by LAN connection. Before about connecting devices, refer to the operating instructions of each device. Using This Manual The Operating Instructions is designed to be read on a
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 4
    on the network, click Refresh to update the screen. If the numbers are still different, check the connections by referring to the Operating Instructions of the remote controller and camera. • The message "User Account Control - An unidentified program wants access to your computer" may appear. In
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 5
    9). Tip For details about checking the MAC address, refer to the operating instructions of each device. 3 Set the camera name. Enter the camera name in camera will be marked. Note Subnet mask and Gateway address entry is supported only for BRBK-IP10/IP7Z firmware version 2.1 or higher. 5 Click Apply
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 6
    to the network. Note Enable access to the remote controllers from an external device in order to update settings. For details, refer to the Operating Instructions of each remote controller. 2 Start RM-IP Setup Tool, and click the Controller tab. The detected remote controllers are displayed on the
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 7
    created for each remote controller. Note The number of groups will vary depending on the remote controller model. For details, refer to the operating instructions of each device. 1 Turn on the remote controllers, cameras, and other devices that are connected to the network. Note Enable access to the
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 8
    4 Click the camera name cell in the Camera Name column for the camera group and camera number you want to assign. The camera names specified in "Configuring the Cameras" (page 4) are displayed in the pull-down menu. 5 Select the camera that you want to assign from the pull-down menu. Camera name To
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 9
    To copy the camera table from another remote controller You can copy an existing camera table, or part of an existing camera table, from another remote controller on the same network. 1 Select the destination remote controller, and mark the checkbox of the camera groups and camera numbers you want
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 10
    Precautions when copying a camera table between RM-IP500 and RM-IP10 The RM-IP500 supports ten groups, while the RM-IP10 supports 16 groups. Each group consists of ten cameras on the RM-IP500, and seven on the RM-IP10. Accordingly, some of the camera groups and
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 11
    Configuring Windows Firewall RM-IP Setup Tool may not operate correctly (no cameras are shown in the list even if they are connected and configured correctly), depending on the configuration of Windows Firewall. In this case, check the Windows Firewall settings. When using Windows 7 To turn Windows
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 12
    4 Select Allow another program.... 3 Select Turn Windows Firewall on or off. 5 Add the program. Click Browse... specify the path of RM-IP Setup Tool, then click Add. 4 Select Turn off Windows Firewall. To turn Windows Firewall on 1 Press and hold the Windows key and press the X key on the
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 13
    4 Select Allow another app.... 5 Add the application. Click Browse... specify the path of RM-IP Setup Tool, then click Add. 13
  • Sony SRG-A40 | Users Guide - RM-IP Setup Tool Guide - Page 14
    Sony Corporation
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
Remote Controller
Setup software RM-IP Setup Tool guide
Software Version 1.1
C-499-100-
12
(1)
© 2017 Sony Corporation