Sony SS-K70ED Instruction Manual

Sony SS-K70ED Manual

Get Sony SS-K70ED PDF manuals and user guides View all Sony SS-K70ED manuals
Add to My Manuals
Save this manual to your list of manuals

Sony SS-K70ED manual content summary:

  • Sony SS-K70ED | Instruction Manual - Page 1
    Hz, 4,000 Hz Dimensions (w/h/d) Mass Approx. 240 × 990 × 400 mm (9 1/2 × 39 × 15 3/4 inches) Approx. 20.0 kg (44 lb 2 oz) Supplied accessories Pedestal (1) Spike (4) Spike pad (4) Jam nut (4) Washer (2) Screw (2) Wrench (1) SS-K70ED Speaker system Loud speaker units 3-way, magnetically
  • Sony SS-K70ED | Instruction Manual - Page 2
    blage SS-K90ED HIGH Speaker System SS-K90ED/K70ED SS-K90ED HIGH SS-K70ED triangle équilatéral. Mise en place des enceintes Support d'enceintes en option 1 Fixez le socle (A) à Hz - 70 000 Hz Fréquence de recoupement 300 Hz, 4 000Hz Dimensions (l/h/p) Poids Env. 240 × 900 × 400 mm (9 1/2 × 35
  • 1
  • 2
SS-K90ED/K70ED
4-251-798-
11
(2)
2003
Sony Corporation
Printed in China
English
Connections
•Before connection, turn off the amplifier to avoid
damaging the speaker system.
•This speaker system is driven best by an amplifier or
receiver rated as per the wattage indicated in the
specification section.
A low-powered amplifier could result in signal
clipping which could result in tweeter burn-out.
Therefore, it is recommended to use an amplifier or
receiver with sufficient power rating.
Note
Avoid driving the speaker system continuously with a
wattage exceeding the maximum input power of each
speaker.
Precautions
•Do not attempt to open the enclosure or remove
speaker units. There are no user-serviceable parts
inside.
•Keep recorded tapes, watches, and personal credit
cards using magnetic coding away from the speaker
system.
•Periodically wipe the cabinet with a soft cloth.
Do not use any type of scouring powder, abrasive pad
or solvent.
•Be sure to install the grill net in the correct direction.
Speaker Placement
Please note that room acoustics can often produce large
difference in the sound for small changes in speaker
placement.
•Set up your speaker system on a hard, flat floor.
•Place the speaker system against a hard wall with its
back about 10 cm (4 inches) away from a wall. The
proportion of bass increases as you move a speaker
close to intersecting room surfaces (wall and wall,
etc.).
•Place the right and left speakers in a similar acoustic
environment.
•It is recommended that the speaker/listener
relationship be an equilateral triangle.
A
Jumper
B
High band terminals
C
Low band terminals
D
Power amplifier
E
Control amplifier
Bi-Wiring Connection
Speaker System
Remove jumper before connecting
SS-K90ED
HIGH
LOW
L
R
L
R
L
R
Standard Connection
Leave jumper in place when connecting
SS-K70ED
SS-K90ED
HIGH
LOW
Right
Left
A
Jumper
B
Amplifier
Positioning the speaker
The optional speaker stand
1
Secure the pedestal (
A
) to the speaker with the
supplied screws (
E
) and washers (
D
). (
A
)
2
Attach the spikes (
B
) and the jam nuts (
C
) to
the bottom of the pedestal (
A
).
Fully insert the
front spikes (
B
) into the pedestal (
A
). (
A
)
3
Lay the spike pads (
F
) (hollow side up) on the
installation site and install the pedestal and
speaker. Using the supplied wrench (
G
),
adjust the back spikes (
B
) until the speaker is
level. (
B
)
A
B