Sony ZRCT-200 Operating Instructions

Sony ZRCT-200 Manual

Get Sony ZRCT-200 PDF manuals and user guides View all Sony ZRCT-200 manuals
Add to My Manuals
Save this manual to your list of manuals

Sony ZRCT-200 manual content summary:

  • Sony ZRCT-200 | Operating Instructions - Page 1
    4-692-870-16 (1) Display Unit Display Controller Operating Instructions Before operating the unit, please read this manual and the supplied Before Using This Unit document thoroughly and retain it for future reference. ZRD-1/ZRD-2 ZRCT-100/ZRCT-200 © 2016 Sony Corporation
  • Sony ZRCT-200 | Operating Instructions - Page 2
    Manual Structure 3 Licenses 3 Condensation 3 Security 3 Burn-in 3 Defective pixels 3 General Precautions 3 Overview 4 System Configuration Diagram 4 Parts Identification 5 ZRD-1/ZRD-2 Display Unit 5 ZRCT-100/ZRCT-200 17 Troubleshooting 17 Error Inputs 22 Supported Signal Formats
  • Sony ZRCT-200 | Operating Instructions - Page 3
    Please Read This First Manual Structure This product includes the following manuals to be used according to the situation. Before Using This Unit (ZRD-1/ZRD-2, ZRCT-100/ ZRCT-200) This includes important safety precautions, specifications, etc. Installation Manual This includes information on
  • Sony ZRCT-200 | Operating Instructions - Page 4
    details on the number of display units that can be connected, refer to the Installation Manual.) Caution Use the Category 6a cable supplied with the ZRD-2 for the network cable • DisplayPort connector • DVI connector (ZRCT-100 only) • HDMI connector (ZRCT-200 only) Control (LAN) Control (LAN
  • Sony ZRCT-200 | Operating Instructions - Page 5
    . Indicator Status Off The display unit is turned off. Lit yellow The display unit is starting up. Blinking yellow A warning has occurred. For details, see "Troubleshooting" (page 17). Lit red The display unit is in standby mode. Blinking red An error has occurred. For details, see
  • Sony ZRCT-200 | Operating Instructions - Page 6
    display unit in the daisychain connection. ZRCT-100/ZRCT-200 Display Controller Front a b This connector MAINTENANCE connector This connector is used for maintenance servicing. c Intake vent Do not block the when errors occur. For details, see "Troubleshooting" (page 17) and "Error Codes
  • Sony ZRCT-200 | Operating Instructions - Page 7
    Rear ZRCT-100 a b cd e f ZRCT-200 m l a k ji h g b cd e f n m k ji h g Caution Do not connector (BNC) Inputs external reference signals used for synchronization. For details, refer to the Installation Manual. i 3D SYNC IN connector (mini-DIN, 3-pin) Inputs 3D sync signals. j CTRL
  • Sony ZRCT-200 | Operating Instructions - Page 8
    l DVI (video input) connectors 1 to 4 (ZRCT-100 only) Connect these to the video processor. m DisplayPort (video input) connectors 1 and 2 Connect these to the video processor. n HDMI (video input) connectors 1 and 2 (ZRCT200
  • Sony ZRCT-200 | Operating Instructions - Page 9
    Note If you press the power switch only once in the power ON state, the POWER indicator will blink red for 2 seconds, but the standby mode will not be entered. You can enter standby mode by pressing the power switch again while the indicator is still blinking red. 2 Turn on the video source
  • Sony ZRCT-200 | Operating Instructions - Page 10
    channel in [Input Select], and click [OK] or [Apply]. The video input changes. [HDMI1] (ZRCT-200 only): Use HDMI connector 1 to display pictures. [HDMI2] (ZRCT-200 only): Use HDMI connector 2 to display pictures. [DVI] (ZRCT-100 only): Use the DVI connectors to display pictures as large as 4K 50p
  • Sony ZRCT-200 | Operating Instructions - Page 11
    details on the supported video signals for ZRCT-200. 3 Use the sliders and buttons for [H Position] and [V Position] to specify the horizontal and vertical positions. The settings are reflected in the picture immediately after they are configured. For details, refer to the Installation Manual
  • Sony ZRCT-200 | Operating Instructions - Page 12
    Settings] screen closes. Configuring the Input Level and Signal Format for HDMI Inputs (ZRCT-200 Only) 1 Select [HDMI1] or [HDMI2] for [Input Select] in Caution Select [Standard Format] when an input device that does not support HDMI 2.0 is connected. 4 When you are finished configuring settings,
  • Sony ZRCT-200 | Operating Instructions - Page 13
    Adjusting the Picture Quality Adjust the contrast, brightness, and other picture quality settings. The settings configured on the primary controller will be applied to all the other display controllers, including the sub controllers. Sub controllers cannot be configured individually. Caution If the
  • Sony ZRCT-200 | Operating Instructions - Page 14
    D65 Custom (Offset)], or [D50 Custom (Offset)], [DCI Custom (Offset)] (ZRCT-200 version 1.22.0 or later), proceed to step 3 . 3 Configure the respectively. For details, refer to the Installation Manual. Caution 3D video display is not supported for HDMI signals. 3D frame sequential mode: This
  • Sony ZRCT-200 | Operating Instructions - Page 15
    the REF IN (external reference signal input) connector on the primary controller via a BNC cable. Note The following external sync signals are supported. • HD tri-level sync (0.6 Vp-p/75Ω/negative sync) • SD black burst/composite sync (0.286 Vp-p/75Ω/ negative sync) Enabling External Synchronization
  • Sony ZRCT-200 | Operating Instructions - Page 16
    different depending on the model you are using. • Supported Web browsers are Internet Explorer and Safari. • The change the password is displayed. Follow the instructions on the screen to change the password. you forget your password, consult with qualified Sony personnel. At that time, we may
  • Sony ZRCT-200 | Operating Instructions - Page 17
    values will not be applied unless you click on [Apply]. Set ADCP. ADCP Service setting area Troubleshooting Be sure to conduct a check before requesting assistance. If the problem persists, contact your local Sony representative. Checking the status of the system and devices You can check the
  • Sony ZRCT-200 | Operating Instructions - Page 18
    Note You can view information on a display controller by double-clicking its controller number or by rightclicking it and selecting [Controller Info.]. [Array Information] Displays the status of each display unit. (gray): The display unit is turned on. (black): The display unit is turned off. (
  • Sony ZRCT-200 | Operating Instructions - Page 19
    Left): stop / speed-down Check the device environment and remove any obstructions from the fan and intake vent. If the problem persists, contact your local Sony representative. Fan (Left): performance degradation Check the fan status and running time. Board UC Board (Reserved) UP Board (Reserved
  • Sony ZRCT-200 | Operating Instructions - Page 20
    ) 230 System 233 PIF 240 System 1) ZRCT-100 only 2) ZRCT-200 only Description Temperature warning Solution Check the device environment and remove any obstructions from the fan and intake vent. If the problem persists, contact your local Sony representative. Rotation stop warning / speed
  • Sony ZRCT-200 | Operating Instructions - Page 21
    condensation may occur inside the device. Signal Formats The system supports the following video signals. 2D Inputs DisplayPort (single input) Input bit length 8-/10-bit Input color sampling RGB 4:4:4 DVI (1 input) (ZRCT-100 only) Resolution 1920 × 1080 Input frame rate 1) 60p/50p/30p/ 25p
  • Sony ZRCT-200 | Operating Instructions - Page 22
    inputs only). 9) 1,000/1,001 frame rate is also supported for 60p/30p/24p. 10) Use a Premium High Speed HDMI cable when using this input signal. 11) Converted to YCbCr 4:2:2, 10-/12-bit first, and then converted to RGB 4:4:4, 10-bit for display. 12) ZRCT-200 version 1.22.0 or later 3D Inputs Frame
  • Sony ZRCT-200 | Operating Instructions - Page 23
    Supported Signal Formats for a Single Controller Resolution Frequency Color sampling 98 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 RGB 4:4:4 1) ZRCT-100 only 2) ZRCT-200 version 1.22.0 or later DisplayPort input Single input Dual input DP1 or DP2 DP1 and DP2 SST
  • Sony ZRCT-200 | Operating Instructions - Page 24
    YCbCr 4:2:2 RGB 4:4:4/YCbCr 4:4:4 YCbCr 4:2:2 RGB 4:4:4/YCbCr 4:4:4 YCbCr 4:2:2 RGB 4:4:4/YCbCr 4:4:4 YCbCr 4:2:2 RGB 4:4:4/YCbCr 4:4:4 YCbCr 4:2:2 RGB 4:4:4/YCbCr 4:4:4 YCbCr 4:2:2 HDMI input (ZRCT-200 only) Single input HDMI1 or HDMI2 8-bit 12-bit 8-bit 12-bit 8-/10-/12-bit 12-bit 8-/10-/12-bit
  • Sony ZRCT-200 | Operating Instructions - Page 25
    Sony Corporation
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
Display Unit
Display Controller
Operating Instructions
Before operating the unit, please read this manual and the supplied Before Using This
Unit document thoroughly and retain it for future reference.
ZRD-1/ZRD-2
ZRCT-100/ZRCT-200
4-692-870-
16
(1)
© 2016 Sony Corporation