TASCAM Celesonic US-20x20 Software/Firmware Update procedures

TASCAM Celesonic US-20x20 Manual

Get TASCAM Celesonic US-20x20 PDF manuals and user guides View all TASCAM Celesonic US-20x20 manuals
Add to My Manuals
Save this manual to your list of manuals

TASCAM Celesonic US-20x20 manual content summary:

  • TASCAM Celesonic US-20x20 | Software/Firmware Update procedures - Page 1
    • Set the phantom power switch to off. Updating the Windows driver and the Mac Settings Panel 88 For Windows 1. Download the latest driver for the operating system you are using from the TEAC Global Site in "Installing the Settings Panel for Mac OS X" in the Owner's Manual. TASCAM US-20x20 1
  • TASCAM Celesonic US-20x20 | Software/Firmware Update procedures - Page 2
    US-20x20 Procedures for updating the firmware Preparing • Before updating firmware, follow the instructions in the Owner's Manual to install the following. Windows : Windows driver computer are not connected, "Supported hardware is not connected." will appears. 2 TASCAM US-20x20 6. This
  • TASCAM Celesonic US-20x20 | Software/Firmware Update procedures - Page 3
    In this case, click the button to close the updater. • If the unit and computer are not connected, "Supported hardware is not connected." will appear. If this happens, check the following. • Confirm that the power is on firmware and the update might not be able to operate properly. TASCAM US-20x20 3
  • 1
  • 2
  • 3
TASCAM
US-20x20
1
US-20x20
Checking the software/firmware versions
Before beginning to update the software/firmware, check the software/firmware version of the US-20x20 being used.
For details about how to check the software/firmware version, See “INTERFACE page” in “6 – Using the Settings Panel” of the Reference
Manual.
Windows INTERFACE page
Mac INTERFACE page
Procedures for updating the computer software
Preparing
•
If the latest software has already been installed, there is no need to update it. Use it as is.
•
Run Windows Update to use the latest system version.
•
Disconnect all cables from the unit except for the power cord.
•
Set the phantom power switch to off.
Updating the Windows driver and the Mac Settings Panel
8
For Windows
1.
Download the latest driver for the operating system you are
using from the TEAC Global Site (http://teac-global.com/)
and save it on the computer to be used with the unit.
2.
Open the saved driver (zip file) on, for example, the
computer desktop.
3.
After uncompression, double-click the “TASCAM_
US-20x20_x.xx.exe” (“x.xx” is the number of driver version)
file to automatically start the installer software.
4.
After this, follow the installation procedures in “Installing the
dedicated driver for Windows” in the Owner's Manual.
8
For Mac
NOTE
•
Depending on the Gatekeeper setting, a warning message
might appear during installation. For information about
Gatekeeper, see “Note about Gatekeeper” of the Reference
Manual.
1.
Download the latest Settings Panel for the operating system
you are using from the TEAC Global Site (http://teac-global.
com/) and save it on the computer to be used with the unit.
2.
Double-click “US-20x20_x.xx.dmg” (“x.xx” is the number of
software version), which is the saved disk image file for the
Settings Panel, and double-click “US-20x20.pkg” inside the
folder that opens.
NOTE
Depending on the computer’s settings, the downloaded ZIP
file might not have opened automatically. In this case, unzip
the ZIP file to access the disk image file.
3.
When the installer starts, click the “Continue” button.
4.
After this, follow the installation procedures in “Installing the
Settings Panel for Mac OS X” in the Owner's Manual.