TEAC HD-P2 HD-P2 Quick Start Guide

»

HD-P2

Quick Start Guide

1

First Recording

Apply power

Connect the AC power adaptor to your HD-P2; turn

it ON by momentarily pressing the spring-loaded

power switch. The HD-P2 will power up

immediately. The HD-P2’s operating system is

stored in internal memory, not the CF card, so you

can turn on the HD-P2 without a CF card inserted.

Adjust the Display

Press the

DISPLAY

key. Turn the

DATA

wheel to

adjust Contrast for optimal viewing. Press the

DISPLAY

key again. Turn the

DATA

wheel to

adjust Brightness. Press the

CANCEL

key to end

adjustments. These settings are remembered when

the unit is power cycled.

Insert Media

Insert a media card into the media slot. The HD-P2

will ask if you would like to format the media. If

this is the first time the media has been used with

the HD-P2 (and it has no other data you wish to

keep) press the

SELECT

key to format the media.

Once formatting is complete the HD-P2 will make

a default project (PROJ0001) and return to the main

screen.

Record Audio

Flip the

LEFT INPUT

and

RIGHT INPUT

switches

(top of unit) to

MIC

. Set the

MIC

switch to

INT

.

Press the

PAUSE

key to enter Monitor mode and

while speaking into the Microphone adjust the input

Levels using the on-screen meters. Press the

REC

key and speak into the microphone for a short test.

Press the

STOP

key when you are done.

Play Audio

Return to the beginning of the audio you just

recorded by pressing the

STOP

+

REW

or

LOCATE

Ô

key

. Press the

PLAY

key

. Adjust the Monitor

(Headset) level control to hear the audio in the

speaker, or headset if one is plugged in. Note that

connecting a headset disables the built-in speaker.

Create a New Project

1. Hold the

MENU

key and press the

PROJECT

key

2. Use the

DATA

wheel to scroll to Create New

Project

3. Press the

SELECT

key

4. Use the

DATA

wheel to scroll to Use Default

�emplate

5. Press the

SELECT

key

6. Press the

SELECT

key again to confirm (or

wait two seconds)

Load A Project

1. Hold the

MENU

key and press the

PROJECT

key

2. Use the

DATA

wheel to scroll to the project to

be loaded

3. Press the

SELECT

key

4. Load Project should already be selected

5. Press the

SELECT

key

Delete A Project

1. Hold the

MENU

key and press the

PROJECT

key

2. Use the

DATA

wheel to scroll to the project to

be deleted

3. Press the

SELECT

key

4. Use the

DATA

wheel to scroll to Delete

5. Press the

SELECT

key

6. Press the

SELECT

key again to confirm this

action cannot be undone

Rename A Project

1. Press the

MENU

key

2. Use the

DATA

wheel to scroll to Project

Menu (this references the currently loaded

project)

3. Press the

SELECT

key

4. Use the

DATA

wheel to scroll to ±ename

5. Press the

SELECT

key to enter the naming

interface

Section	Page
First Recording	1
Apply power	1
Adjust the Display	1
Insert Media	1
Record Audio	1
Play Audio	2
Set Up Default Project Settings	2
Set Up Project Templates	2
Input Settings	2
Top Panel	2
Menus	2
Setting The Clock Source	3
Enabling Time Code Chase	3
Menus	3
Front Panel	3
Immediate Record	3
Reformat Media	3
Transport & Markers	4
Transport Functions	4
Markers	4
FireWire Dock	4
Dock the HD-P2	4

TEAC HD-P2 HD-P2 Quick Start Guide

TEAC HD-P2 Manual

TEAC HD-P2 manual content summary: