TEAC HS-4000 HS-4000 V1.21 Manual Addendum

X

HS-4000

TASCAM HS-4000

1

D01160320A

The following functions have been added in firmware V1.21.

i

Support for playback of regular WAV files

i

Automatic recognition of external files added

i

Manual locating based on timecode time has been added to take and

playlist modes

i

When a new project or session is created, the take name is reset to the

default

i

Progress bar when recording in take mode added

i

Digital input unlocking no longer mutes the signal

i

Confidence monitoring enabled/disabled/OFF status shown on the Home

Screen

i

Playlist mode changes to ADJUST screen operations and addition of

rehearsal playback function for audio monitoring

i

Assignment changing on the ENTRY list screen added

i

Change BC$STANDBY/END range at once function added

i

Addition of on air mode that plays back files in the root folder

i

BC$END operation mode setting added

i

SONY P2 REC command support

i

System setting backup and preset memory functions added

i

Auto Marker PRE/REC/END ON/OFF settings added

i

Bounce save destination now selectable

i

Take copy function added

i

ETHERNET page added to the REMOTE SETUP screen

i

Network functions (FTP/telnet/VNC) added

Support for playback of regular WAV files

WAV files that are not Broadcast Wave Format (BWF) can now be played

back. In addition, if you edit the playback starting time (Start TC) of a WAV

file, a pop-up message appears explaining that the file will be automatically

converted to BWF format.

External file automatic recognition function

External files read from a CF card will now be recognized automatically.

Manual rebuilding is no longer necessary.

Manual locate function based on timecode added to take

and playlist modes

When the time display mode is

T/C

, you can now locate manually based on

the timecode time in take and playlist modes.

Take name resets when new project/session created

When a new project/session is created, the

NEXT TAKE NAME

page setting of

the Home Screen is now reset to the default

Session Name

value with the

format “session name–T001”. (See “

a

NEXT TAKE NAME button” on page 20

of the Owner's Manual.)

Progress bar when recording in take mode

When recording in take mode, beneath the time display on the Home Screen,

a red progress bar has been added that repeatedly extends from left end to

right end in about 5 seconds (see the illustration below) to make watching

the recording status easy.

Progress bar

Digital input unlocking no longer mutes the signal

Even if digital input is detected as being unlocked, the input signal is no

longer muted.

Confidence monitoring enabled/disabled/OFF status

shown on the Home Screen

A confidence monitoring button (icon) has been added between the trans-

port icon and the time display on the Home Screen to allow its status to be

checked on the Home Screen.

Press this button to open the

REC MODE

page of the

REC SETUP

screen

where you can set confidence monitoring.

The confidence monitoring ON/OFF settings have not changed. See “Record-

ing settings (REC SETUP)” in 10 – Internal settings on page 79 of the Owner's

Manual.

Confidence Monitor enabled

Confidence Monitoring is enabled when the settings are as follows.

i

Confidence Monitor: ON

i

Fs:

44.1, 48, 47.952, 48.048 kHz (48 kHz±0.1%)

i

Record function: Enabled for 2 tracks or less

Confidence Monitor disabled

Even if Confidence Monitor is ON, it will be disabled if either the Fs or Rec

Function is as follows.

i

Confidence Monitor: ON

i

Fs: 88.2, 96 kHz

i

Record function: Enabled for 3 tracks or more

Confidence Monitor OFF

When C

onfidence Monitor is OFF, it is always disabled

.

i

Confidence Monitor: OFF

New functions added in firmware V1.21

TEAC HS-4000 HS-4000 V1.21 Manual Addendum

TEAC HS-4000 Manual

TEAC HS-4000 manual content summary: