TEAC LR-10 LR-10 firmware version 1.01 release notes

TASCAM LR-10

1

LR-10

Release Notes

Updates

Always use the most recent firmware for this device.

Please visit the TASCAM web site at http://www.tascam.

com to check for the latest firmware.

Maintenance items

V1.01 Fixes

If you pressed and held the

•

Ô

or



button to

search backward or forward at the very beginning or

end of a song, the speed would return to normal. This

issue has been fixed.

If the

•

AREA

item on the

PLAY MODE

screen was

set to

PLAYLIST

, and you set IN (starting) or OUT

(ending) points and then made a move in the playlist

or otherwise edited it, the IN and OUT points would not

be saved correctly. This issue has been fixed.

If the

•

AREA

item on the

PLAY MODE

screen is set to

PLAYLIST

, and you select a file not added on the

PLAYLIST

screen and then use the

LOOP

button to

try to set an IN (starting) or OUT (ending) point, the

following pop-up message will now appear.

File not in PLAYLIST

Note

When operating the unit using USB bus power, if you

output sound from the speaker at near maximum volume,

depending on the computer being used, the power

supply status display might change from the

icon

to the

icon. This is not a problem with the unit, and

battery power is not used.

Confirmation of firmware version

Confirm the firmware version of your LR-10 before

conducting a firmware update.

1

Turn the unit’s power ON.

2

Press the MENU key to open the

MENU

screen.

3

Use the

§

/BROWS or

¶

/MIC button to select

INFORMATION

menu item (highlight the item),

and press the

Á

or

¯

button to open the

INFORMATION

screen.

4

Use the

§

/BROWS or

¶

/MIC button to open the

SYSTEM (3/3)

page and confirm the

System

Ver.

(firmware version) is displayed.

You do not need to update the unit’s firmware if

the version shown is the same as or newer than the

version that you intend to use for the update.

Firmware update procedures

NOTE

When you updated the firmware, make sure that the

batteries have enough remaining power or use an optional

AC adaptor (PS-P520). The program has been set so that the

update will not be conducted if battery power is insufficient.

1

Download the most recent firmware from the

TASCAM web site (http://www.tascam.com).

2

Turn the unit’s power ON and use the included

USB cable to connect it with a computer. This unit

will be recognized as an external drive (external

storage device) by the computer.

3

Copy the downloaded firmware to the

UTILITY

folder on the LR-10.

4

After copying has completed, disconnect the

unit from the computer following the correct

procedures, remove the USB cable and turn the

unit power OFF.

5

While pressing and holding both the

Ô

and

Á

buttons, turn the unit power ON.

The unit starts up in update mode, and the update file

appears on the screen.

NOTE

If this screen does not appear, turn the power OFF. Then

•

while pressing and holding both the

Ô

and

Á

buttons,

turn the unit’s power ON again. Continue to press and

hold the

Ô

and

Á

buttons firmly until this screen

appears.

When firmware has been copied to this unit’s UTILITY

•

folder from a Mac, in addition to the firmware file itself,

another file with “._” added to the beginning of the

firmware name is also shown. Use the file without the “._”

at the beginning of the name.

This screen shows a list of the firmware update files inside

•

the UTILITY folder of the unit. Also, the screen shows the

firmware copied at Step 3 above. “No Update File” appears

if there is no update file in the UTILITY folder.

The screen shown is an example. The actual display differs.

•

6

Select the firmware (highlight the item) then press

Á

button.

The following screen appears.

D01141600A

TEAC LR-10 LR-10 firmware version 1.01 release notes

TEAC LR-10 Manual

TEAC LR-10 manual content summary: