TP-Link Archer C1900 Archer C1900 US V1 User Guide
TP-Link Archer C1900 Manual
 |
View all TP-Link Archer C1900 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link Archer C1900 manual content summary:
- TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 1
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router REV1.0.0 1910011429 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 3
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 4
2012 MHz Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 5
used outside own premises General authorization required for network and service supply (not for spectrum) Country Bulgaria Restriction Not implemented of DFS mechanism described in ETSI standard EN 301 893 V1.3.1 and subsequent versions General authorization required if used outside own - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 6
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 7
power source. Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 8
Description: AC1900 High Power Wireless Dual Band Gigabit Router Model No.: Archer C1900 Trademark: TP-LINK We in conformity with the following standards or other normative documents EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1 EN 55022: 2010 + AC: 2011 EN 55024: 2010 EN 60950-1: - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 9
Panel 5 Chapter 2. Connecting the router 7 2.1 System Requirements 7 2.2 Installation Environment Requirements 7 2.3 Connecting the router 7 Chapter 3. Quick Setup 9 Chapter 4. Basic 15 4.1 Network Map ...15 4.2 Internet ...15 4.3 Wireless ...20 4.4 USB Settings ...20 4.4.1 File Sharing 20 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 10
5.10 Forwarding ...67 5.10.1 Virtual Servers 67 5.10.2 Port Triggering 69 5.10.3 DMZ...71 5.10.4 UPnP ...72 5.11 Security ...73 5.11.1 Basic Security 73 5.11.2 Advanced Security 74 5.11.3 Local Management 76 5.11.4 Remote Management 77 5.12 Parental Control ...78 5.13 Access - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 11
DDNS 99 5.18 IPv6 Support ...100 5.18.1 IPv6 Status 101 5.18.2 IPv6 Setup 102 5.19 System Tools ...110 5.19.1 Time Settings 110 5.19.2 Diagnostic 112 5.19.3 Firmware Upgrade 114 5.19.4 Factory Defaults 115 5.19.5 Backup & Restore 115 5.19.6 Reboot ...116 5.19.7 Password...117 5.19.8 System - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 12
should be found in your package: Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router DC Power Adapter for Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Quick Installation Guide Resource CD for Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 13
. Flexible Access Control The Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port Triggering - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 14
in this guide stands for Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router without any explanation. 1.3 Main Features Complies with IEEE 802.11ac. One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation RJ45 Ethernet ports, supporting Auto MDI - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 15
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 1.4 Panel Layout 1.4.1 The Front to the Ethernet (1/2/3/4) port(s). No any device is connected to the Ethernet (1/2/3/4) port. The Internet port is connected, and the Internet is accessible. The Internet port is connected, but the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 16
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router (USB 1) (USB 2) On Off Flashing On Off Flashing On Off The connection via WPS is successful. The connection via WPS fails. The router is identifying the device connected to the USB 2.0 port 2.0: The USB 2.0 port connects to a USB - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 17
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router button to and wait the router to reboot to its factory default settings. Internet: This port is where you will connect the DSL/cable Modem, or Ethernet. Ethernet (1, 2, 3, 4): These ports (1, 2, 3, 4) connect the router to the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 18
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Chapter 2. Connecting the router 2.1 System Requirements Broadband Internet Access Service service successfully. If there is any problem, has one. 3. Connect the modem to the Internet port on your router with an Ethernet cable. 4. Turn - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 19
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 2-1 Hardware Installation Figure 2-2 USB Installation Note: If you want to use the router to share files or printer, plug the USB storage device to the USB port or connect the printer to the router with a matching cable. - 8 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 20
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Chapter 3. Quick Setup 1. Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: Configuring the PC. 2. Open a web-browser (such as - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 21
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 4. Then WAN Connection Type page will appear as shown below. Select your connection type if you know what it is or click Auto Detect button; then follow the instructions to continue. Note: 1) It's likely that you will skip Step 3 and - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 22
Static IP Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 3-6 WAN Connection Type IP Address - Enter the IP address into this field. Subnet Mask - Enter the subnet mask into this field. It is usually 255.255.255.0. Default Gateway - Enter the gateway IP address into - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 23
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 3-8 WAN Connection Type VPN Server IP/ Domain Name - Enter the server IP address/name provided by your ISP. Username - Enter the username provided by your ISP. This field is case-sensitive. Password - Enter the Password - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 24
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 3-9 WAN Connection Type VPN Server IP/Domain Name - Enter the server IP address/name provided by your ISP. Username - Enter the username provided by your ISP. This field is case-sensitive. Password - Enter the Password - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 25
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Wireless 2.4GHz/5GHz - Displays whether the wireless function is enabled or not. Network Name (SSID) - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 26
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Chapter 4. Basic 4.1 Network Map Network Map provides a router-centered dashboard that lets you see the status of your - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 27
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 4-2 Internet 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page as shown below. Figure 4-3 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 28
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Primary/Secondary Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP. Primary/Secondary - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 29
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 4-5 PPPoE User Name/Password - Enter the User Name and Password L2TP VPN Server IP/Domain Name - Enter the IP address or domain name of your VPN server. User Name/Password - Enter the User Name and Password provided by - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 30
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5. If your ISP provides PPTP connection, please select PPTP/Russia PPTP option. And you should enter the following parameters (Figure 5-8). Figure 4-7 PPTP/Russia PPTP VPN service is name and password. Dynamic manually. - 19 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 31
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 4.3 Wireless Choosing menu " of your wireless network will be hidden from the Wi-Fi network. Password - Create a password for your wireless network. The password must have a minimum of 8 characters in length. Click the Save button - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 32
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 4-9 File Sharing used to access the USB device connected to the router. Access Method - Select the check boxes for the access methods that you want. 1) Network Neighborhood: This method is enabled by default. To access the USB - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 33
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router ii. Enter ftp://192.168.0.1:21 in the dialog box and click the OK button. 3) FTP (Remote): This method is disabled by default. If you select this check box, remote users can access the USB drive through FTP over the Internet. This - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 34
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Allow Guest Network Access - If this checkbox is selected, guests are allowed to access the sharing file. Enable Authentication - If this checkbox is selected, then the file sharing is need authentication. Enable Write Access - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 35
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 4-12 Guest Network Allow Guests To See Each Other - If ON is selected, anyone who connects to the guest network can access each other. Allow Guests To Access My Local Network - If ON is selected, anyone who connects to the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 36
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Chapter 5. Advanced 5.1 Status Choose menu "Advanced→Status", you can see the current status information about the router. Figure 5-1 Status - 25 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 37
Archer C1900 AC1900 WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 38
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default few ISPs' DHCP servers do not support the broadcast applications. If you cannot - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 39
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default PPPoE User Name/Password - Enter the User Name and Password provided by your ISP - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 40
Archer C1900 AC1900 number of minutes you want to have elapsed before your Internet access disconnects. Connect Automatically - The connection can be re-established Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 41
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-6 PPPoE Advanced Settings MTU Size - The default MTU size is "1480" bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. Service Name/AC Name - The service - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 42
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-7 WAN - L2TP/Russia L2TP VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP. User Name/Password - Enter the User Name and Password you attempt to access the Internet again - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 43
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Connect Automatically - Connect automatically after the router is disconnected. To use this option, check the radio button. Connect Manually - You can configure the router to make it connect or disconnect manually. After a - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 44
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP. User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 45
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Static IP - Connections which use static IP address assignment. The router cannot detect PPTP/L2TP connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. 5.2.2 MAC - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 46
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-10 LAN MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 47
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.4 Wireless 2.4GHz Figure 5-12 SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be TP-LINK_XXXX. This value is case-sensitive. For example, TEST is NOT the same as test. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 48
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router wireless features of default channel is set to Auto, so the router will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 49
Archer C1900 AC1900 PIN. The default PIN of the router can be found in the label or User Guide. Restore PIN - Restore the PIN of the router to its default value. to the existing network manually by clicking this button. If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 50
Archer C1900 AC1900 not have the WPS button, but has a Wi-Fi Protected Setup PIN number. Step 1: Enable WPS. The default is enabled. Click the Add device button in Figure 5-15, your wireless network. There are five wireless security modes supported by the router: WPA-Personal, WPA2-Personal, WPA-Enterprise, - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 51
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-17 Wireless Security Disable type based on pre-shared passphrase. The router is configured by this security type by default. Version - You can choose the version of the WPA-PSK or WPA2-PSK security on the drop-down list - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 52
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-18 WPA/WPA2 - Personal Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the default PIN code, which is labeled on the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 53
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Group Key Type - you can choose the type for the WEP security on the drop-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 54
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.4.4 Wireless MAC Filtering Choose menu "Advanced→Wireless 2.4GHz→Wireless MAC Filtering", you can control the wireless access a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 55
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 3. Select Enabled or function. 2. Select the radio button "Allow the stations specified by any enabled entries in the list to access" for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 56
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.4.5 Wireless Advanced router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 57
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router broadcast and familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 5.4.6 Wireless Statistics Choose menu - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 58
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router If the numbers of connected wireless stations go beyond one page, click the Next button to go to - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 59
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Wireless Network Name - The wireless network name (SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be TP-LINK_XXXX_5G. This value is case-sensitive. For example, TEST is NOT - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 60
Archer C1900 AC1900 High Power Wireless Dual Band password in this blank. 5.5.2 WPS Choose menu "Advanced→Wireless 5GHz→WPS", you can see the screen as shown in Figure 5-28. This section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi Protected Setup - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 61
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can does not have the WPS button, but has a Wi-Fi Protected Setup PIN number. Step 1: Enable WPS. The default is enabled. Click the Add device button in Figure 5-28, - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 62
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.5.3 Wireless Security Choose menu "Advanced→Wireless 5GHz→Wireless Security", you can configure the security settings of your wireless network. There are five wireless security modes supported by default. Version - You can choose - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 63
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 5-31. Figure 5-31 WPA/WPA2 - Personal Wireless Password - You can enter ASCII characters between 8 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 64
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Radius Server IP - Enter the IP address of the Radius server. Radius Port - Enter the port number of the Radius server. Radius Password - Enter the password on the drop-down list. The default setting is Automatic, which can select - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 65
Archer C1900 AC1900 →Wireless→MAC Filtering", you can control the wireless access by configuring the Wireless MAC Filtering function, shown Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC instructions: - 54 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 66
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 1. Enter the function. 2. Select the radio button "Allow the stations specified by any enabled entries in the list to access" for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 67
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.5.5 Wireless Advanced router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 68
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 69
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: This page will be refreshed automatically every 5 seconds. 5.6 Guest Network Choose menu "Advanced→Guest Network", you can - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 70
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Access And Bandwidth Control Allow Guests to See Each Other - If this checkbox is selected, anyone who connects to the guest network can communicate with each other. Allow Guests To Access My Local Network - If this checkbox is - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 71
Archer C1900 AC1900 within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. Address Lease Time - The Address Lease Time is the amount - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 72
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway - (Optional.) It is suggested to input the IP address of the Ethernet - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 73
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 5-42 Address Reservation MAC Address - The MAC - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 74
Archer C1900 AC1900 the router. Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to safely remove the USB storage device that is connected to USB port. This takes the drive offline. 5.8.2 File Sharing Choose menu - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 75
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-46 File Sharing Sharing Account Use Login Account - Select this radio button, and the sharing account is the same with the login account. Use Following Account - Select this radio button, then you have to specify the new - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 76
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 2) FTP: This method is disabled by default. If you select this check box and click the Save button, the LAN users can access the USB drive through FTP. To access the USB drive for example from a Windows computer: i. Select Start > Run. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 77
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Allow Guest Network Access - If this checkbox is selected, guests are allowed to access the sharing file. Enable Authentication - If this checkbox is selected, then the file sharing is need authentication. Enable Write Access - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 78
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.10 Forwarding Figure 5-49 NAT Boost Figure 5-50 The Forwarding menu There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 79
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Service Port - The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX - YYY; XXX is the Start port and YYY is the End port). Internal Port - The Internal Service Port - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 80
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service Port Triggering Choose menu "Advanced→Forwarding→Port Triggering", you can view and add port - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 81
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either TCP, UDP, or All. 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All. 5. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 82
Archer C1900 AC1900 be refused. 3. Incoming Ports ranges cannot overlap each other. 5.10.3 DMZ Choose menu "Advanced→Forwarding→DMZ", and then you service such as Internet gaming or videoconferencing. The router forwards packets of all services to the DMZ host. Any PC whose port is being forwarded - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 83
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.10.4 UPnP Choose menu "Advanced→Forwarding→UPnP", and then as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 84
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.11 Security Figure 5-57 The Security traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable it. - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 85
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the router. PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point support address and port - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 86
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-59 Advanced Security Packets Statistics Interval (5~60) - The default value Flood, UDP Flood and ICMP-Flood. DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 87
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLOOD Attack Filtering. TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 88
the port number used is 8080, please enter http://202.96.12.8:8080 in your browser. Later, you may be asked for the router's password. After successfully entering the username and password, you will be able to access the router's web-based utility. 2. Be sure to change the router's default password - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 89
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.12 Parental Control Control function can be used to control the internet activities of the child, limit the child to access certain websites and restrict the time of surfing. Figure 5-62 Parental Control Settings Parental Control - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 90
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-63 Add or Modify Parental Control Entry 2. . For example: If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.google.com on Saturday only, while the parent PC with MAC address 00-11-22-33-44-BB is - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 91
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 1. Click "Parental Control" menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field. 2. Click "Advanced→Access Control→Schedule" on - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 92
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.13.1 Rule Choose menu "Advanced→Access Control→Rule", and then you can view and set Access Control rules in the screen as shown in Figure 5-65. Figure 5-65 Access Control Rule Management Enable Internet Access Control - Select the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 93
Archer C1900 AC1900 Method One: 1. Click Setup Wizard button and the next screen will appear as shown in Figure 5-66. Figure 5-66 Quick Setup - Create a Host Entry following item: LAN IP Address - Enter the IP address or address range of the host in dotted-decimal format (e.g. 192.168.0.23). If the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 94
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-67 Quick Setup - Create an Access Target Entry Target Description .0.33). Target Port - Specify the port or port range for the target. For some common service ports, you can make use of the Common Service Port item below. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 95
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-68 Quick Setup deselect the checkbox and specify the Start Time and Stop Time manually. Start Time - Enter the start time in HHMM format Figure 5-69. Figure 5-69 Quick Setup - Create an Internet Access Control Entry Rule Name - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 96
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Target - In this filed, the menu Access Control on the left. Select Enable Internet Access Control and choose "Allow the packets specified by any enabled access control policy to pass through the router". 2. Click Setup Wizard button. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 97
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 4. Add a new target set a Host list in the screen as shown in Figure 5-71. The host list is necessary for the Access Control Rule. Figure 5-71 Host Settings Host Description - Displays the description of the host and this description - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 98
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-72 Add or Modify a Host Entry 2) If you select MAC Address, the screen is shown as Figure 5- - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 99
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.13.3 Target Choose menu "Advanced→Access Control→Target", and then you can view and set a Target list in the screen as shown in Figure 5-74. The target list is necessary for the Access Control Rule. Figure 5-74 Target Settings - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 100
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-76 Add or Modify an Access Target Entry 1) In Target Description Settings page and see the following list. 5.13.4 Schedule Choose menu "Advanced→Access Control→Schedule", and then you can view and set a schedule in the next - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 101
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-77 Schedule Settings Schedule Description - Displays the description of the schedule and this description is unique. Day - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 102
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 103
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router To add static routing which portion of an IP Address is the network portion, and which portion is the host portion. Default Gateway - This is the IP Address of the gateway device that allows for contact between the router and - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 104
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-82 System Routing Table Destination Network - The Destination Network is the address of the network or host - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 105
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-84 Bandwidth Control the information about the rules such as address range. Egress bandwidth - This field displays the max and mix upload bandwidth through the Internet port, the default is 0. Ingress bandwidth - This - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 106
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router To add/modify a Bandwidth Control rule, follow the steps below. 1. Click Add New... shown in Figure 5-85, you - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 107
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-88 Binding Setting MAC Address - The MAC address of the controlled computer in the LAN. IP Address - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 108
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 1. Click the Find button in Figure 5-88. 2. Enter the MAC Address or IP Address. 3. Click the Find button - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 109
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: An instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click the Login button to login the DDNS service. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 110
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service. Note: If you want to login again with another account after a successful login, please click the Logout - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 111
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-94 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 112
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.18.1 IPv6 Status Figure 5-96 IPv6 Status of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400 seconds. IPv6 Address - Displays the LAN IPv6 Address. - 101 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 113
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.18.2 IPv6 Setup Figure 5-97 Enable/Disable IPv6 Enable IPv6 - Tick the checkbox to enable the IPv6 function. It's enabled by default use PPPoEV6 that requires a user name and password. Tunnel 6to4 - Connections which use 6to4 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 114
1) DHCPv6 Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-98 DHCPv6 - SLAAC Figure 5-99 DHCPv6 - DHCPv6 Server Get non-temporary IPv6 address - Get a non-temporary IPv6 address from the ISP. - 103 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 115
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Get IPv6 prefix delegation - Get a temporary IPv6 address and IPv6 prefix from the ISP, the temporary IPv6 address is set to the WAN port, and the LAN port you access a range is 1~691200 seconds. The default value is 86400 seconds. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 116
2) Static IPv6 Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-100 Static IPv6 - SLAAC Figure 5-101 Static IPv6 - DHCPv6 Server IPv6 Address - Enter the IPv6 address in dotted-decimal notation provided by your ISP. Default Gateway - Enter the default gateway in - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 117
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router MTU Size - The Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400 seconds. LAN IPv6 Address - Displays the LAN IPv6 Address. 3) PPPoEv6 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 118
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-103 PPPoEv6 - DHCPv6 Server User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Get IPv6 Address Way Get non-temporary IPv6 address - Get a non-temporary IPv6 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 119
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400 seconds. LAN IPv6 Address - Displays the LAN IPv6 Address. 4) Tunnel 6to4 Figure 5-104 Tunnel 6to4 - SLAAC - 108 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 120
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-105 Tunnel 6to4 - DHCPv6 Server Address/Subnet Mask/Default Gateway - the IPv4 address/ subnet mask/ default gateway assigned, in dotted-decimal notation. MTU Size - The normal MTU (Maximum Transmission Unit) value for - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 121
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Release Time - the length of time a network user will be allowed to keep connecting to the router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~ - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 122
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-107 Time settings field. Daylight Saving Status - Displays the status whether the Daylight Saving is in use. To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 123
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router To set time automatically: be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully; otherwise, these functions will not take effect. 2. The time will be lost if - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 124
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-109 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots a name resolution problem. In this target (destination). The default is 20. Click Start - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 125
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-110 Diagnostic Results hardware version. To upgrade the router's firmware, follow these instructions below: 1. Download a most recent firmware upgrade file from our website (www.tp-link.com). 2. Enter or select the path - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 126
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: 1) New firmware versions are posted at www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 127
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-113 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the router's configuration, follow these instructions. Click the Browse - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 128
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5.19.7 Password Choose menu "Advanced→System Tools→Password", and then you can change the factory default user name and password of the router in the next screen as shown in Figure 5-115. Figure 5-115 Password It is strongly - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 129
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-116 System Log Auto Mail Feature - Indicates whether auto mail feature is . Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need User Name and Password to log in. - 118 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 130
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Note: Only when you select Authentication, do you have to enter the User Name and Password in the following fields. User Name - Your mail account name filled in the From field. The part behind @ is included. Password manually - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 131
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure 5-118 Statistics Current Statistics Status - Enable or Disable. The default value is disabled. To enable it, click the Enable button. If it is disabled, the function of DoS protection in Security settings will be disabled. - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 132
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Statistics Table: IP/MAC Address The IP and MAC address are displayed with related statistics. Total The total - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 133
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the Internet port on the - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 134
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 2. How do I configure the router to access Internet by Ethernet users? 1) Login login to the router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link "Forwarding" "Service Port" blank - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 135
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure A-5 Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the "Status" page. 4) How to enable DMZ Host: Log in to the router, click the "Forwarding" menu on the left of - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 136
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router, you must change the WEB management port default LAN - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 137
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 3) Log in to the router, click the "Forwarding" menu on the left of your browser, and click the "Virtual Servers" submenu. On the "Virtual Servers" page, click Add New..., then on the "Add - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 138
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Appendix B: Configuring the PC In this section, we'll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed. 1. Install TCP/ - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 139
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 6) Select Obtain an IP address automatically and Obtain DNS server automatically, as shown in the Figure below: Figure B-3 - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 140
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router If the result displayed is the router's IP address is 192.168.0.1, your PC's IP address must be within the range of 192.168.0.2 ~ 192.168.0.254. 3. Is the default LAN IP of the router correct? Note: If the LAN IP of the modem - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 141
Archer C1900 AC1900 High Power Wireless Dual Band Gigabit Router Appendix C: Specifications General Standards Protocols Ports Auto-Negotiation Internet RJ45 port; 4 10/100/1000M Auto-Negotiation Ethernet RJ45 ports supporting Auto MDI/MDIX; 2 USB ports supporting storage/FTP/Media/Print Server - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 142
Archer C1900 AC1900 High Power Wireless Dual Band for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding traditional phone lines. ISP (Internet Service Provider) - A company that provides access to the Internet. - 131 - - TP-Link Archer C1900 | Archer C1900 US V1 User Guide - Page 143
Archer C1900 AC1900 Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. SSID - A Service . It corresponds to the ESSID in the wireless Access Point and to the wireless network name. WEP
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
 |
 |
Archer C1900
AC1900 High Power Wireless Dual Band
Gigabit Router
REV1.0.0
1910011429