TP-Link T1600G-52TSTL-SG2452 T1600G-28TS V1 Installation Guide
TP-Link T1600G-52TSTL-SG2452 Manual
View all TP-Link T1600G-52TSTL-SG2452 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1600G-52TSTL-SG2452 manual content summary:
- TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 1
Business Networking Solution Installation Guide JetStream Gigabit Smart Switch T1600G-28TS (TL-SG2424) T1600G-52TS (TL-SG2452) - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 2
. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 3
of the switch. Chapter 5 Configuration. This chapter instructs you to configure the switch via Web Interface and CLI commands. Appendix A Troubleshooting. Appendix B Hardware Specifications. Audience This Installation Guide is for: Network Engineer Network Administrator Conventions Due to - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 4
16 4.3 Verify Installation 16 4.4 Power On 17 4.5 Initialization 17 Chapter 5 Configuration 18 5.1 Configure the Switch via GUI 18 5.2 Configure the Switch Using CLI 19 Appendix A Troubleshooting----------- 21 Appendix B Hardware Specifications------- 22 III Contents - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 5
for workgroups and departments, provides wire-speed performance and abundant L2 and L2+ management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 6
. Each has a corresponding Link/Act LED and a 1000Mbps LED. SFP Port Designed to install the SFP module. T1600G-28TS features 4 individual SFP ports and supports 1000M SFP module connection only. The front panel of T1600G-52TS is shown as the following figure. RESET LEDs 10/100/1000Mbps RJ45 Port - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 7
or 1000Mbps. Each has a corresponding 1000Mbps LED. SFP Port Designed to install the SFP module. T1600G-52TS features 4 individual SFP ports and supports 1000M SFP module connection only. Port Feature Model T1600G-28TS T1600G-52TS 10/100/1000Mbps RJ45 Port 24 48 SFP Port 4 4 ■■ Rear Panel - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 8
JetStream Gigabit Smart Switch Grounding Terminal The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed information, please refer to Chapter 3 Lightning Protection. Power - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 9
following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Two Mounting Brackets and the One Resource CD Fittings 2.2 Safety Precautions To avoid any device damage and bodily injury caused by improper use - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 10
, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table. Environment Operating Storage - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 11
the device on a rack or a flat workbench, please note the following items: ■■ The rack or workbench is flat and stable, and sturdy enough to support the weight of 5.5kg at least. ■■ The rack or workbench has a good ventilation system. The equipment room is well ventilated. ■■ The rack is well - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 12
the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the grounding and stability of the rack. 2. - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 13
JetStream Gigabit Smart Switch Rack Figure 2-3 Rack Installation Caution: ■■ Please set 5~10cm gaps around the device for air circulation. ■■ Please avoid any heavy thing placed on the device. ■■ Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 14
JetStream Gigabit Smart Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 15
small as possible. ■■ Requirements for the distance between Ethernet cable and other pipelines are shown in the table. Other Pipelines Down-conductor PE Service pipe Compressed air pipe Thermal pipe (not wrapped) Thermal pipe (wrapped) Gas pipe Ethernet Cable Min Parallel Net Length L (mm) 1000 50 - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 16
, which is also a necessary measure to protect the body from electric shock. In different environments, the device may be grounded differently. The following will instruct you to connect the device to the ground in two ways, connecting to the grounding bar or connecting to the ground via the power - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 17
JetStream Gigabit Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■■ Connecting to the Ground via the Power Supply If the device is installed in the normal environment, the device can be grounded via the PE ( - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 18
JetStream Gigabit Smart Switch Grounding Terminal Ground Cable Equipotential Bonding Cable Grounding Bar Figure 3-3 Equipotential Bonding When equipotential bonding, please note that the cable should be copper conductor with a sectional area of 6mm2 at least, wrapped green with yellow stripe. - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 19
JetStream Gigabit Smart Switch When purchasing or using a signal lightning arrester, please observe the following rules: ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work. - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 20
JetStream Gigabit Smart Switch Chapter 4 Connection 4.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable Figure 4-1 Connecting the RJ45 Port 4.2 SFP Port Connect the SFP port to a SFP module as shown below. SFP - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 21
JetStream Gigabit Smart Switch 4.4 Power On Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector into a power outlet as the following figure shown. Figure 4-3 Connecting to Power Supply Note: The figure is to illustrate the - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 22
is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B in the User Guide on the Resource CD. 2. Enter admin for the default User Name and Password, both in lower case letters. Then - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 23
JetStream Gigabit Smart Switch Figure 5-3 Main Page of the Switch 5.2 Configure the Switch Using CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 24
JetStream Gigabit Smart Switch 3. Type cmd in the prompt Run window as Figure 5-5 shows and click OK. Figure 5-5 Run Window 4. Type telnet 192.168.0.1 in the command prompt shown as Figure 5-6, and press the Enter button. Figure 5-6 Connecting to the Switch 20 Configuration - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 25
JetStream Gigabit Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? Press the RESET button for at least 5 seconds address should be set as 192.168.0.x ("x" is any number from 2 to 254) and subnet mask as 255.255.255.0. Troubleshooting 21 - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 26
JetStream Gigabit Smart Switch Appendix B Hardware Specifications Item Standards Transmission Medium LEDs Operating Temperature Storage Temperature Operating Humidity Storage Humidity Content IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3ab 1000Base-T IEEE 802.3z - TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 27
- TP-Link T1600G-52TSTL-SG2452 | T1600G-28TS V1 Installation Guide - Page 28
Website: http://www.tp-link.com E-mail: [email protected] 7106505040 REV1.0.0
Installation Guide
JetStream Gigabit Smart Switch
T1600G-28TS (TL-SG2424)
T1600G-52TS (TL-SG2452)
Business Networking Solution