TP-Link T2600G-52TS T2600G Series Switches CLI Reference Guide Guide
TP-Link T2600G-52TS Manual
View all TP-Link T2600G-52TS manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T2600G-52TS manual content summary:
- TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 1
CLI Reference Guide T2600G-18TS /T2600G-28TS (TL-SG3424) /T2600G-28TS-DC/ T2600G-28MPS (TL-SG3424P) / T2600G-28SQ/ T2600G-52TS (TL-SG3452) 1910012658 REV4.2.0 December 2019 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 3
2.1 line ...20 2.2 media-type rj45 ...21 Charpter 3. User Interface 22 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 enable...22 service password-encryption ...22 enable password ...23 enable secret ...24 configure...25 exit ...26 end ...26 clipaging...27 history ...27 history clear ...28 Charpter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 4
manual...34 system-time ntp...34 system-time dst predefined...36 system-time dst date...37 system-time dst recurring ...38 hostname...39 location ...40 contact-info ...40 ip address ...41 ip address-alloc...42 reset...43 service reset remove backup-image ...51 firmware upgrade ...51 boot autoinstall - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 5
cable-diagnostics interface 62 show cpu-utilization...62 show memory-utilization ...63 show temperature ...63 show voltage ...64 Charpter 6. EEE Configuration Commands 65 6.1 eee...65 6.2 show interface eee ...65 Charpter 7. SDM Template Commands 67 7.1 sdm prefer ...67 7.2 show sdm prefer - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 6
...94 ddm bias_current_threshold...95 ddm tx_power_threshold ...96 ddm rx_power_threshold ...97 show ddm configuration ...98 show ddm status ...99 Charpter 13. Etherchannel Commands 100 13.1 13 show lacp sys-id ...105 Charpter 14. MAC Address Commands 107 14.1 mac address-table static ...107 V - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 7
count 110 14.7 mac address-table notification (interface 112 14.8 mac address-table security (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 113 14.9 mac address-table vlan-security (For T2600G-18TS 114 14.10 show mac address-table ...115 14.11 clear mac address-table...115 14.12 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 8
Charpter 17. Protocol-based VLAN Commands 132 17.1 17.2 17.3 17.4 17.5 protocol-vlan template...132 protocol-vlan vlan ...133 protocol-vlan group...134 show protocol-vlan template 134 show protocol-vlan vlan...135 Charpter 18. Private VLAN Commands 136 18.1 18.2 18.3 18.4 18.5 18.6 18.7 18.8 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 9
24 21.25 21.26 21.27 ip igmp snooping (global) ...156 ip igmp snooping version ...156 ip igmp snooping drop-unknown 157 ip igmp snooping header-validation 158 ip igmp snooping vlan-config 158 ip igmp snooping vlan-config (immediate-leave 160 ip igmp snooping vlan-config (report-suppression 160 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 10
.10 debug spanning-tree ...203 spanning-tree (global)...204 spanning-tree (interface)...204 spanning-tree common-config 205 spanning-tree mode...206 spanning-tree mst configuration 207 instance...207 name ...208 revision ...209 spanning-tree mst instance ...210 IX - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 11
...223 lldp hold-multiplier ...224 lldp timer ...225 lldp receive...226 lldp transmit ...226 lldp snmp-trap ...227 lldp tlv-select...228 lldp management-address ...228 lldp med-fast-count...229 lldp med-status ...230 lldp med-tlv-select ...230 lldp med-location...231 show lldp ...232 show lldp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 12
ip route...253 show ip route specify...254 show ip route summary...255 show ipv6 interface ...255 show ipv6 route...256 show ipv6 route summary...256 Charpter 29. IPv6 Address Configuration Commands 258 29.1 29.2 29.3 29.4 29.5 ipv6 enable ...258 ipv6 address autoconfig ...259 ipv6 address link - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 13
31.15 31.16 31.17 31.18 service dhcp server ...274 ip dhcp server extend-option capwap-ac-ip 274 ip dhcp server extend-option vendor-class-id 275 ip dhcp server exclude-address 276 ip dhcp server pool ...277 ip dhcp server ping timeout ...277 ip dhcp server ping packets...278 network...279 lease - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 14
server excluded-address 288 show ip dhcp server manual-binding 288 show ip dhcp server binding ...289 clear ip dhcp server statistics 289 clear ip dhcp server binding...290 Charpter 32. DHCP Relay Commands 291 32.1 32.2 32.3 32.4 32.5 32.6 32.7 32.8 32.9 32.10 32.11 32.12 service dhcp relay - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 15
qos cos-map ...313 34.10 show qos dot1p-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 313 34.11 show qos dot1p-remap (For T2600G-18TS 314 34.12 show qos dscp-map interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS 314 34.13 show qos dscp-map (For - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 16
key 349 show ip http configuration ...350 show ip http secure-server ...351 Charpter 40. SSH Commands 352 40.1 40.2 40.3 40.4 40.5 40.6 40.7 ip ssh server ...352 ip ssh port...352 ip ssh version ...353 ip ssh algorithm ...354 ip ssh timeout...354 ip ssh max-client ...355 ip ssh download ...356 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 17
...368 aaa authentication enable...369 aaa authentication dot1x default 370 aaa accounting dot1x default 371 show aaa authentication...371 show aaa accounting ssh) ...377 enable authentication (console 378 ip http login authentication ...378 ip http enable authentication 379 show aaa global... - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 18
Charpter 45. Port Security Commands 398 45.1 45.2 mac address-table max-mac count 398 show mac address-table max-mac-count 398 Charpter 46. Port Mirroring 405 access-list mac ...406 access-list ip ...407 access-list combined ...409 access-list ipv6 ...411 access-list packet-content config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 19
IMPB Commands 422 48.1 48.2 48.3 48.4 48.5 48.6 48.7 ip source binding ...422 ip dhcp snooping ...423 ip dhcp snooping vlan...424 ip dhcp snooping max-entries 424 show ip source binding ...425 show ip dhcp snooping ...426 show ip dhcp snooping interface 426 Charpter 49. IPv6 IMPB Commands 428 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 20
54. DoS Defend Commands 456 54.1 54.2 54.3 ip dos-prevent ...456 ip dos-prevent type ...456 show ip dos-prevent ...458 Charpter 55. sFlow Commands (Only for Certain Devices 460 55.1 55.2 55.3 55.4 55.5 55.6 55.7 sflow address...460 sflow enable...461 sflow collector collector-ID ...461 sflow - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 21
show ethernet-oam configuration 474 show ethernet-oam event-log 475 show ethernet-oam statistics 475 show ethernet-oam status ...476 Charpter 57. DLDP Commands 477 57.1 57.2 57.3 57.4 57.5 57.6 57.7 57.8 dldp (global) ...477 dldp interval ...477 dldp shut-mode...478 dldp reset (global)...479 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 22
snmp-server traps acl ...495 snmp-server traps ip...495 snmp-server traps power...496 snmp-server traps link-status 497 rmon history ...498 rmon event ...499 range ...513 show power inline ...514 show power inline configuration interface 514 show power inline information interface 515 show power - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 23
.7 60.8 60.9 60.10 60.11 60.12 ip arp inspection burst-interval 520 ip arp inspection recover ...521 show ip arp inspection...522 show ip arp inspection interface 522 show ip arp inspection vlan ...523 show ip arp inspection statistics 523 clear ip arp inspection statistics 524 Charpter 61. ND - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 24
models if not specially noted, and T2600G-28TS is taken as an example model in the example commands. Some models featured in this guide may be unavailable in your country or region. For local sales information, visit https://www.tp-link.com. Overview of this Guide Chapter 1: Using the CLI Provide - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 25
Commands Provide information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). Chapter 14: MAC Address Commands Provide information about the commands used for Address configuration. Chapter 15: IEEE 802.1Q VLAN Commands Provide - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 26
Static Routes Commands Provide information about the commands used for configuring the Static Route function. Chapter 29: IPv6 Address Configuration Commands Provide information about the commands used for configuring the System IPv6 addresses. Chapter 30: ARP Commands Provide information about the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 27
. Chapter 47: ACL Commands Provide information about the commands used for configuring the ACL (Access Control List). Chapter 48: IPv4 IMPB Commands Provide information about the commands used for binding the IP address, MAC address, VLAN and the connected Port number of the Host together. Chapter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 28
about the commands used for configuring the DLDP (Device Link Detection Protocol). Chapter 58: SNMP Commands Provide information about the commands used for configuring the SNMP (Simple Network Management Protocol) functions. Chapter 59: PoE Commands (For T2600G-28MPS only) Provide information about - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 29
USB port is required. The USB driver is provided on the resource CD. Follow the InstallSheild Wizard to accomplish the installation. The TP-Link USB Console Driver supports the following Windows operating systems: ■ 32-bit Windows XP SP3 ■ 64-bit Windows XP ■ 32-bit Windows Vista ■ 64-bit Windows - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 30
32-bit Windows 8.1 ■ 64-bit Windows 8.1 After the TP-Link USB Console Driver is installed, the PC's USB port will -> Device Manager -> Ports ->USB Serial Port. Figure 1-1 USB Serial Port Number 4. Configure the terminal emulation program or the terminal to use the following settings: ■ Baud rate: - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 31
and "T2600G-28TS>" will appear indicating that you have successfully logged in to the switch and you can use the CLI now. Figure 1-2 Log in to the Switch Note: The first time you log in, change the password to better protect your network and devices. 1.1.2 Logon by Telnet The switch supports Login - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 32
. Figure 1-4 Connect to the Switch 3. Type the default user name and password (both of them are admin), then press the Enter button so as to enter User EXEC Mode. Figure 1-5 Enter into the User EXEC Mode Note: The first time you log in, change the password to better protect your network and devices - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 33
for detailed commands information of the Telnet connection configuration. 1.1.3 Logon by SSH To log on by username and password, which are both admin by default. Key Authentication Mode: It requires a public key 2. The first time you log in, change the password to better protect your network and devices. - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 34
software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type. Figure 1-8 SSH Connection Configuration 2. Click the Open button in the above figure to log on to the switch. Enter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 35
■ Key Authentication Mode 2. Select the key type and key length, and generate SSH key. Figure 1-10 Generate SSH Key Note: 1. The key length is in the range of 512 to 3072 bits. 2. During the key generation, randomly moving the mouse quickly can accelerate the key generation. 12 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 36
3. After the key is successfully generated, please save the public key and private key to a TFTP server. Figure 1-11 Save the Generated Key 4. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows: Figure 1-12 Download the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 37
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading cannot be interrupted. 5. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login. Figure 1-13 SSH Connection Configuration 14 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 38
downloaded. Figure 1-15 Log on the Switch 1.2 CLI Command Modes The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and VLAN Configuration Mode. 15 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 39
Interface Configuration Mode can also be divided into Interface Ethernet, Interface link-aggregation and some other modes, which command to access interface Configuration mode. Use the vlan vlan-list to access VLAN Configuration mode. T2600G-28TS (config-if)# or T2600G-28TS(config-if -range)# - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 40
mode from Global Configuration mode. T2600G-28TS (config-if)# or T2600G-28TS(config-if -range Configure parameters for several Ethernet ports. c). Interface link-aggregation: Configure parameters for a link-aggregation, such as broadcast storm. d). Interface range link-aggregation: Configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 41
Privileged EXEC mode from User EXEC mode by using the enable command. In default case, no password is needed. In Global Configuration Mode, you can configure password for Admin level by enable password command. Once password is configured, you are required to enter it to access Privileged EXEC mode - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 42
. Otherwise, the words will be identified as several strings. 1.4.3 Parameter Format Some parameters must be entered in special formats which are shown as follows: ■ MAC address must be enter in the format of xx:xx:xx:xx:xx:xx. ■ One or several values can be typed for a port-list or a vlan - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 43
users have access to these commands. Example Enter the Console port configuration mode and configure the console port 0: T2600G-28TS(config)#line console 0 Enter the Virtual Terminal configuration mode so as to prepare further configurations such as password and login mode for virtual terminal 0 to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 44
default configuration, please use no media-type rj45 command. Syntax media-type rj45 no media-type rj45 Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the RJ-45 console input: T2600G-28TS(config)# line console 0 T2600G - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 45
EXEC Mode from User EXEC Mode: T2600G-28TS>enable Enter password: T2600G-28TS# 3.2 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the configuration is written, using the symmetric encryption - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 46
Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the global encryption function: T2600G-28TS(config)# service password-encryption 3.3 enable password Description The enable password command is used to set or change follow. By default, the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 47
EXEC Mode: T2600G-28TS(config)#enable password 0 admin 3.4 enable secret Description The enable secret command is used to set a secret password, which is using an MD5 encryption algorithm, for users to access Privileged EXEC Mode from User EXEC Mode. To return to the default configuration, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 48
. The password will be displayed in the encrypted form. T2600G-28TS(config)#enable secret 0 admin 3.5 configure Description The configure command is used to access Global Configuration Mode from Privileged EXEC Mode. Syntax configure Command Mode Privileged EXEC Mode Privilege Requirement Only Admin - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 49
Mode Privilege Requirement None. Example Return to Global Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: T2600G-28TS(config-if)# exit T2600G-28TS(config)#exit T2600G-28TS# 3.7 end Description The end command is used to return to Privileged - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 50
use no clipaging command. Syntax clipaging no clipaging Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Disable the pause function for the screen display: T2600G-28TS(config)#no clipaging 3.9 history Description The history command is used to show the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 51
command. Syntax history clear Command Mode Privileged EXEC Mode and any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear the commands you have entered in the current mode: T2600G-28TS(config)#history clear 28 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 52
so as to protect the settings of the switch from being randomly changed. 4.1 user name (password) Description The user name command is used the right to edit or modify. It is "admin" by default. For more details about privilege restrictions, please refer to the 's configuration file. After the 29 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 53
configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration configured password will take effect. Example Add and enable a new admin user named "tplink", of which the password is "admin" and unencrypted: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 54
, only the latest configured password will take effect. Example Add and enable a new admin user named "tplink", of which the password is "admin". The password will be displayed in the encrypted form. T2600G-28TS(config)#user name tplink privilege admin secret 0 admin 4.3 service password-recovery - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 55
its startup. Syntax service password-recovery no service password-recovery Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the switch's password-recovery feature: T2600G-28TS(config)# service password-recovery 4.4 show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 56
of the users, including access-control, max-number and the idle-timeout, etc. Syntax show user configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the security configuration information of the users: T2600G-28TS(config)# show user - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 57
the time is 12/20/2010 17:30:35 T2600G-28TS(config)# system-time manual 12/20/2010-17:30:35 5.2 system-time ntp Description The system-time ntp command is used to configure the time zone and the IP address for the NTP Server. The switch will get UTC automatically if it has connected to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 58
Solomon Is., New Caledonia, Vladivostok. UTC+12:00 -- TimeZone for Fiji, Magadan, Auckland, Welington. UTC+13:00 -- TimeZone for Nuku'alofa, Samoa. ntp-server -- The IP address for the Primary NTP Server. 35 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 59
users have access to these commands. Example Configure the system time mode as NTP, the time zone is UTC-12:00, the primary NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163, the fetching-rate is 11 hours: T2600G-28TS(config)# system-time ntp UTC-12:00 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 60
the daylight saving time as USA standard: T2600G-28TS(config)#system-time dst predefined USA 5.4 system-time dst date Description The system-time dst date command is used to configure the one-off daylight saving time. The start date is in the current year by default. The time range of the daylight - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 61
by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the daylight saving time from zero clock, Apr 1st to zero clock Oct 1st and the offset is 30 minutes in 2015: T2600G-28TS(config)# system - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 62
no hostname Parameter hostname -- System Name. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example "T2600G-28TS". Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 63
characters at most. It is "SHENZHEN" by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the system location as SHENZHEN: T2600G-28TS(config)# location SHENZHEN 5.8 contact-info Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 64
the system contact information as www.tp-link.com: T2600G-28TS(config)# contact-info www.tp-link.com 5.9 ip address Description This ip address command is used to configure the IP address and IP subnet mask for the specified interface manually. The interface type includes: routed port, port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 65
interface to obtain IP address from the BOOTP Server. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Client function on the Lay 3 routed port 1/0/1: T2600G-28TS(config)# interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 66
except its IP address: T2600G-28TS# reset except-ip 5.12 service reset-disable Description The service reset-disable command is used to disable the reset function of the console port or reset button. To enable the reset function, use no service reset-disable command. By default, the reset function - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 67
T2600G-28TS(config)# service reset-disable 5.13 reboot Description The reboot command is used to reboot access to these commands. Example Reboot the switch: T2600G-28TS# reboot 5.14 reboot-schedule Description This reboot-schedule command is used to configure the switch to reboot at a certain time - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 68
; otherwise the switch will reboot at the time point the next day. Example Specify the switch to save the configuration files and reboot in 200 minutes, T2600G-28TS(config)# reboot-schedule in 200 save_before_reboot 5.15 copy running-config startup-config Description The copy running-config startup - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 69
148 and name this file config.cfg: T2600G-28TS# copy startup-config tftp ip-address 192.168.0.148 filename config Backup the configuration files to TFTP server with the IP fe80::1234 and name this file config.cfg: T2600G-28TS# copy startup-config tftp ip-address fe80::1234 filename config 5.17 copy - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 70
TFTP server with the IP 192.168.0.148: T2600G-28TS# copy tftp startup-config ip-address 192.168.0.148 filename config Download the configuration file named as config.cfg to the switch from TFTP server with the IP fe80::1234 T2600G-28TS# copy tftp startup-config ip-address fe80::1234 filename config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 71
Admin level users have access to these commands. Example Export the backup configuration file of the switch to the TFTP server with the IP 192.168.0.148 and name the file config.cfg: T2600G-28TS# copy backup-config tftp ip-address 192.168.0.148 filename config 5.19 copy backup-config startup-config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 72
Only Admin level users have access to these commands. Example Download the configuration file named config.cfg from the TFTP server with the IP 192.168.0.148: T2600G-28TS# copy tftp backup-config ip-address 192.168.0.148 filename config 5.22 boot application Description The boot application - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 73
-- Specify the image file to be configured. By default, the image1.bin is the startup image T2600G-28TS(config)# boot application filename image2 startup 5.23 boot config Description The boot config command is used to configure the configuration file as startup configuration or backup configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 74
access to these commands. Example Configure the config2.cfg as the startup image: T2600G-28TS(config)# boot config filename config2 . Syntax firmware upgrade ip-address ip-addr filename name Parameter ip-addr -- IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 75
the file firmware.bin in the TFTP server with the IP address 192.168.0.148, and reboot the switch with this firmware: T2600G-28TS# firmware upgrade ip-address 192.168.0.148 filename firmware.bin It will Syntax boot autoinstall start no boot autoinstall start Command Mode Global Configuration Mode 52 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 76
to these commands. Example Start Auto Install function: T2600-28TS(config)# boot autoinstall persistent-mode 5.28 boot autoinstall auto-save Description The boot autoinstall auto-save command is used to automatically save the new configuration file that was downloaded by Auto Install function to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 77
-28TS(config)# boot autoinstall auto-reboot 5.30 boot autoinstall retry-count Description The boot autoinstall retry-count command is used to configure retry count when Auto Install function uses TFTP to download configuration files in a cycle of Auto Install process. To set retry count to default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 78
Install function. Syntax show boot autoinstall Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of Auto Install function: T2600-28TS# show boot autoinstall 5.32 show boot autoinstall downloaded-config Description The show boot - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 79
-- The IP address of the destination node for ping test. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234. -n count -- The amount of times to send test data during Ping testing. It ranges from 1 to 10. By default, this - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 80
-- The IP address of the destination device. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234. maxHops -- The maximum number of the route hops the test data can pass though. It ranges from 1 to 30. By default, this value - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 81
Device Location, System Contact, Hardware Version, Firmware Version, System Time, Run Time and so on. Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the system information: T2600G-28TS# show system-info 5.36 show image - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 82
users have access to these commands. Example Display the system boot configuration information: T2600G-28TS# show boot 5.38 show running-config Description The show running-config command is used to display the current operating configuration of the system or of a specified port. Syntax show running - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 83
Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the saved configuration: T2600G-28TS# show startup-config 5.40 show system-time Description The show system-time command is used to display the time information of the switch. Syntax show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 84
information of the switch. Syntax show system-time dst Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DST information of the switch: T2600G-28TS# show system-time dst 5.42 show system-time ntp Description The show system-time ntp command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 85
of the cable connected to the switch, locate and diagnose the trouble spot of the network. Syntax show cable-diagnostics interface { fastEthernet EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Show the cable-diagnostics of port 3: T2600G-28TS# show cable-diagnostics - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 86
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the memory utilization information of the switch: T2600G-28TS# show memory-utilization 5.46 show temperature Note: Only T2600G-28TS-DC supports this command. Description The show temperature - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 87
show temperature 5.47 show voltage Note: Only T2600G-28TS-DC supports this command. Description The show voltage command is used to display the voltage of DC power board. Syntax show voltage Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 88
access to these commands. Example Enable EEE on port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#eee 6.2 show interface eee Description The show interface eee command is used to display the EEE configuration on each port. Syntax show interface eee [ fastEthernet - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 89
Privilege Requirement None. Example Display the EEE configuration of each port T2600G-28TS# show interface eee 66 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 90
sdm prefer command is used to configure the SDM template. The SDM template is used to allocate system resources to best support the features being used in your application. To return to use the default template, please use the sdm prefer default command. The template change will take effect after - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 91
sdm prefer { used | default | enterpriseV4 | enterpriseV6 } Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the resource allocation of the template currently in use, and the template that will become active after a reboot: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 92
-range named "tRange1" for the switch: T2600G-28TS(config)# time-range tRange1 8.2 absolute Description The absolute command is used to create an absolute time-range for the time-range of the switch. To delete the corresponding absolute time-range configuration, please use no absolute command. 69 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 93
T2600G-28TS(config)#time-range tRange1 T2600G-28TS(config-time-range)#absolute from 05/05/2017 to 10/05/2017 8.3 periodic Description The periodic command is used to create a periodic mode time-range for the time-range of the switch. To delete the corresponding periodic mode time-range configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 94
and Power User level users have access to these commands. Example Configure the time-range named "tRange2" as a periodic time-range and specify the date and time as 8:30 to 12:00 on weekends: T2600G-28TS(config)#time-range tRange2 T2600G-28TS(config -time-range)#periodic start 08:30 end 12:00 day - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 95
and Power User level users have access to these commands. Example Create a holiday named "holiday1" and configure the start date as October 1st and the end date as October 3rd: T2600G-28TS(config)# holiday holiday1 start-date 10/01 end-date 10/03 8.6 show holiday Description The show holiday - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 96
time range. Syntax show time-range [name ] Parameter name --Specify the time range name with 1 to 16 characters. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the defined time range: T2600G-28TS# show time-range 73 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 97
Power User level users have access to these commands. Example To enter the Interface gigabitEthernet Configuration Mode and configure port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 9.2 interface range gigabitEthernet Description The interface range gigabitEthernet command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 98
at all if the command results in an error on one port. Example To enter the Interface range gigabitEthernet Configuration Mode, and configure ports 1, 2, 3, 6, 7 and 9 at the same time by adding them to one port-list: T2600G-28TS(config)# interface range gigabitEthernet 1/0/1-3,1/0/6-7,1/0/9 75 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 99
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a Description Port_5 to port 1/0/5: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 100
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Disable port 1/0/3: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 101
T2600G-28TS(config-if)# duplex full 9.7 jumbo-size Description The jumbo-size command is used to specify the size of jumbo frames. Syntax jumbo-size size Parameter size -- The value of jumbo frames. It ranges from 1518 to 9216 bytes, and the default is 1518 bytes. Command Mode Global Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 102
. Example Configure the Speed Mode as 100Mbps for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# speed 100 9.9 serdes-mode (Only for Certain Devices) Note: Only T2600G-18TS, T2600G-28TS, T2600G-28TS-DC, T2600G-28MPS, T2600G-52TS support this command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 103
Only Admin and Operator level users have access to these commands. Example Configure port 1/0/26 to collocate with electrical interface modules: T2600G-28TS(config)# interface gigabitEthernet 1/0/26 T2600G-28TS(config-if)# serdes-mode sgmii 9.10 clear counters Description The clear counters - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 104
of all fiber ports. Syntax show fiber ports Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all fiber ports: T2600G-28TS(config)# show fiber ports 9.12 show interface status Description The show interface status command is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 105
-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the statistics information of all Ethernet ports and port channels: T2600G-28TS(config)# show interface counters Display the statistics information of port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 106
and Any Configuration Mode Privilege Requirement None. Example Display the configurations of all Ethernet ports and port channels: T2600G-28TS(config)# show interface configuration Display the configurations of port 1/0/2: T2600G-28TS(config)# show interface configuration gigabitEthernet 1/0/2 83 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 107
is used to configure the forward port/ T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# port isolation gi-forward-list 1/0/1-2,1/0/4 po-forward-list 2 Set all Ethernet ports and port channels to forward list of port 1/0/2, namely restore to the default setting: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 108
its forward port list, ranging from 1 to 6. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the forward-list of port 1/0/2: T2600G-28TS# show port isolation interface gigabitEthernet 1/0/2 Display the forward-list of all Ethernet ports and - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 109
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the loopback detection function globally: T2600G-28TS of sending loopback detection packets. It ranges from 1 to 1000 seconds. By default, this value is 30. 86 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 110
2 to 1000000 seconds. By default, this value is 90. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the recovery-time as 70 seconds: T2600G-28TS(config)# loopback-detection recovery-time - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 111
detection function of ports 1-3: T2600G-28TS(config)# interface range gigabitEthernet 1/0/1-3 T2600G-28TS(Config-if-range)# loopback-detection 11.5 loopback-detection config process-mode Description The loopback-detection config process-mode command is used to configure the process-mode for the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 112
User level users have access to these commands. Example Configure the loopback detection process-mode as port-based, and configure the recovery mode as manual for port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# loopback-detection config process-mode port-based - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 113
. Syntax show loopback-detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of loopback detection function: T2600G-28TS# show loopback-detection global 11.8 show loopback-detection interface Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 114
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of loopback detection function and the status of all ports: T2600G-28TS# show loopback-detection interface Display the configuration of loopback detection function and the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 115
no ddm state enable Default Setting Enabled on all the SFP ports. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Example Enable DDM function on port 1/0/25: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm state - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 116
an exceeding alarm threshold event is encountered. Default Setting none, which means the port will T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm shutdown warning 12.3 ddm temperature_threshold Description The ddm temperature_threshold command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 117
in Celsius. Default Setting None. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Example Configure the high_alarm threshold of DDM temperature on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 118
in Volt. Default Setting None. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Example Configure the high_alarm threshold of DDM voltage on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 119
in mA. Default Setting None. Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet) Example Configure the high_alarm threshold of DDM Bias Current on the port 1/0/25 as 5: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 120
in mW. Default Setting None. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Example Configure the high_alarm threshold of DDM Tx Power on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 121
in mW. Default Setting None. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Example Configure the high_alarm threshold of DDM Rx Power on the port 1/0/25 as 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/25 T2600G-28TS(config-if)#ddm - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 122
value. Command Mode Privileged EXEC Mode and Any Configuration Mode Example View the DDM configuration state: T2600G-28TS(config)#show ddm configuration state View the threshold of the DDM Voltage value: T2600G-28TS(config)#show ddm configuration voltage 12.9 show ddm status Description The show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 123
aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the load. 13.1 channel-group Description The channel-group command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 124
(config)# interface range gigabitEthernet 1/0/2-4 T2600G-28TS(config-if-range)# channel-group 1 mode on 13.2 port-channel load-balance Description The port-channel load-balance command is used to configure the Aggregate Arithmetic for LAG. To return to the default configurations, please use no port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 125
Arithmetic for LAG as "src-dst-ip": T2600G-28TS(config)# port-channel load-balance src-dst-ip 13.3 lacp system-priority Description The lacp system-priority command is used to configure the LACP system priority globally. To return to the default configurations, please use no lacp system-priority - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 126
by default. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the LACP port priority as 1024 for ports 1-3: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 127
The EtherChannel information in summary. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the detailed information of EtherChannel Group 1: T2600G-28TS(config)# show etherchannel 1 detail 13.6 show etherchannel load-balance Description The show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 128
-group-num -- The EtherChannel Group number, ranging from 1 to 14. By default, it is empty, and will display the information of all LACP groups. internal and Any Configuration Mode Privilege Requirement None. Example Display the internal LACP information of EtherChannel Group 1: T2600G-28TS(config)# - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 129
Example Display the LACP system priority: T2600G-28TS(config)# show lacp sys-id 106 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 130
. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a static Mac address entry to bind the MAC address 00:02:58:4f:6c:23, VLAN1 and port 1 together: T2600G-28TS(config)# mac address-table static 00 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 131
. Example Delete the MAC addresses on VLAN 1: T2600G-28TS(config)# no mac address-table dynamic vid 1 14.3 mac address-table aging-time Description The mac address-table aging-time command is used to configure aging time for the dynamic address. To return to the default configuration, please use no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 132
Only Admin, Operator and Power User level users have access to these commands. Example Configure the aging time as 500 seconds: T2600G-28TS(config)# mac address-table aging-time 500 14.4 mac address-table filtering Description The mac address-table filtering command is used to add the filtering - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 133
2 seconds: T2600G-28TS(config)# mac address-table notification global-status enable table-full-status enable interval 2 14.6 mac address-table max-mac-count Description The mac address-table max-mac-count command is used to configure the Port Security. To return to the default configurations, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 134
aging time and can only be deleted manually too. However, the learned entries will be saved even the switch is rebooted. status -- Select the action to be taken when the number of the MAC addresses reaches the maximum learning number on the port. By default, this function is disabled. • forward: The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 135
: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# mac address-table max-mac-count max-number 30 mode static status drop 14.7 mac address-table notification (interface) Description The mac address-table notification command is used to configure the MAC change notification - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 136
T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# mac address-table notification learn-mode-change enable 14.8 mac address-table security (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The mac address-table security command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 137
no match in the MAC address table: T2600G-28TS(config)# mac address-table security vid 2 max-learn 1000 drop 14.9 mac address-table vlan-security (For T2600G-18TS) Description The mac address-table security command is used to configure the maximum number of MAC address cane be learned in specified - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 138
desired entry. By default, all the entries are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all address entries: T2600G-28TS(config)# show mac address-table 14.11 clear mac address-table Description The show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 139
to display the Aging Time of the MAC address. Syntax show mac address-table aging-time Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the Aging Time of the MAC address: T2600G-28TS(config)# show mac address-table aging-time 14.13 show mac - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 140
Mode Privilege Requirement None. Example Display the security configuration of all ports: T2600G-28TS(config)# show mac address-table max-mac-count all Display the security configuration of port 1/0/1: T2600G-28TS(config)# show mac address-table max-mac-count interface gigabitEthernet 1/0/1 14.14 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 141
Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the total MAC entry information in different VLANs: T2600G-28TS(config)# show mac address-table count 14.16 show mac address-table address Description The show mac address-table address command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 142
:23:00 in VLAN 1: T2600G-28TS(config)#show mac address-table address 00:00:00:00:23:00 vid 1 14.17 show mac address-table vlan Description The show mac address-table vlan command is used to display the MAC address configuration of the specified vlan. Syntax show mac address-table vlan vid Parameter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 143
. Example Display the notification configuration of all the ports: T2600G-28TS(config)# show mac address-table notification all 14.19 show mac address-table security Description The show mac address-table security command is used to display the MAC address security configuration globally or of the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 144
of 2-3, 5. It is multi-optional. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN 2-10 and VLAN 100: T2600G-28TS(config)# vlan 2-10,100 Delete VLAN 2: T2600G-28TS(config)# no vlan 2 121 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 145
16 characters at most. Command Mode VLAN Configuration Mode(VLAN) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the name of VLAN 2 as "group1": T2600G-28TS(config)# vlan 2 T2600G-28TS(config-vlan)# name group1 15.3 vlan_trunk - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 146
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable VLAN Trunk for port 1/0/3: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 147
User level users have access to these commands. Example Configure Gigabit Ethernet port 1/0/4 whose link type is "general" to VLAN 2 and its egress-rule as "tagged": T2600G-28TS(config)#interface gigabitEthernet 1/0/4 T2600G-28TS(config-if)#switchport general allowed vlan 2 tagged 15.6 switchport - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 148
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable Ingress Checking on the port 1/0/2: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 149
to the default setting, T2600G-28TS(config-if)#switchport acceptable frame general 15.9 show vlan summary Description The show vlan summary command is used to display the summarized information of IEEE 802.1Q VLAN. Syntax show vlan summary Command Mode Privileged EXEC Mode and Any Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 150
of IEEE 802.1Q VLAN. Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the brief information of IEEE 802.1Q VLAN: T2600G-28TS(config)# show vlan brief 15.11 show vlan Description The show vlan command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 151
Requirement None. Example Display the information of vlan 5: T2600G-28TS(config)# show vlan id 5 15.12 show interface switchport Description The show interface switchport command is used to display the IEEE 802.1Q VLAN configuration information of the specified port/port channel. Syntax show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 152
coming from the MAC address will be tagged with this VLAN ID. 16.1 mac-vlan mac-address Description The mac-vlan mac-address command is used to Description to the MAC address for identification, which contains 8 characters at most. Command Mode Global Configuration Mode Privilege Requirement Only - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 153
T2600G-28TS(config)#mac-vlan mac-address 00:11:11:01:01:12 vlan 2 Description TP 16.2 mac-vlan Description The mac-vlan command is used to enable a port for the MAC-based VLAN feature. Only the port is enabled can the configured MAC-based VLAN take effect. To disable the MAC-based VLAN function, - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 154
EXEC Mode and Any Configuration Mode Privilege Requirement None. Parameter mac-addr -- MAC address, in the format of XX:XX:XX:XX:XX:XX. vlan-id -- Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094. Example Display the information of all the MAC-based VLAN entry: T2600G-28TS(config)#show mac-vlan - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 155
of the Protocol-based VLAN Template. You can get the template corresponding to the number by the show protocol-vlan template command. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. 132 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 156
Protocol-based VLAN template named "TP" whose Ethernet protocol type is 0x2024: T2600G-28TS(config)#protocol-vlan template name TP frame ether_2 ether-type 2024 protocol-vlan vlan command. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 157
-- Specify the protocol group ID. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface Gigabit Ethernet port 20 to protocol group 1: T2600G-28TS(config)#interface gigabitEthernet 1/0/20 T2600G-28TS(config-if)#protocol-vlan group 1 17.4 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 158
Syntax show protocol-vlan template Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of the Protocol-based VLAN templates: T2600G-28TS(config)#show protocol-vlan template 17.5 show protocol-vlan vlan Description The show protocol - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 159
) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the VLAN 3 as the primary VLAN of the private VLAN: T2600G-28TS(config)#vlan 3 T2600G-28TS(config-vlan)#private-vlan primary 18.2 private-vlan community Description The private-vlan community - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 160
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the VLAN 4 as the community VLAN of the private VLAN: T2600G-28TS(config)#vlan 4 T2600G-28TS(config-vlan)#private-vlan community 18.3 private-vlan isolated Description The private-vlan isolated - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 161
Associate primary VLAN 3 with community VLAN 4 as a private VLAN: T2600G-28TS(config)#vlan 3 T2600G-28TS(config-vlan)#private-vlan association 4 18.5 switchport private-vlan Description The switchport private-vlan command is used to configure the private VLAN mode for the switchport. To invalid the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 162
Requirement Only Admin and Operator level users have access to these commands. Example Configure Gigabit Ethernet port 3 as "host": T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport private-vlan host 18.6 switchport private-vlan host-association Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 163
Only Admin and Operator level users have access to these commands. Example Configure promiscuous type Gigabit Ethernet port 1/0/3 as a member of primary VLAN 3 and secondary VLAN 4: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport private-vlan mapping 3 4 140 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 164
Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display the configuration information of all Private VLAN: T2600G-28TS(config)#show vlan private-vlan 18.9 show vlan private-vlan interface Description The show vlan private-vlan interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 165
Example Display the configuration information of all the Ethernet ports: T2600G-28TS(config)#show vlan private-vlan interface 142 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 166
at the network access terminal of the Internet Service Provider. And these packets will be transmitted with T2600G-28TS(config)#dot1q-tunnel 19.2 switchport dot1q-tunnel tpid Description The switchport dot1q-tunnel tpid command is used to configure Global TPID for the ports. To restore to the default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 167
It must be 4 Hex integers. By default, it is 8100. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range these commands. Example Configure TPID of port 1/0/2 as 0x9100: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#switchport - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 168
mapping feature globally: T2600G-28TS(config)#dot1q-tunnel mapping 19.4 switchport dot1q-tunnel mode Description The switchport dot1q-tunnel mode command is used to configure the VPN port's mode. To close this VPN port, please use the no switchport dot1q-tunnel mode command. By default, no port has - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 169
missdrop no switchport dot1q-tunnel missdrop Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / function for Gigabit Ethernet port 1/0/3: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport dot1q-tunnel missdrop - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 170
tunnel use_inner_priority Command Mode Interface Configuration Mode (interface gigabitEthernet / : For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS, choose a UNI port to enable VLAN mapping. For T2600G-18TS, ranging from 1 to 4094. sp-vlan -- Service Provider VLAN ID, ranging from 1 to 4094. 147 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 171
Interface Configuration Mode Service Provider VLAN as VLAN 3: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#switchport dot1q-tunnel mapping 2 3 19.8 switchport dot1q-tunnel replace Note: Only T2600G-28TS, T2600G-28TS-DC, T2600G-28MPS, T2600G-28SQ, and T2600G-52TS support - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 172
to replace the Customer VLAN (VLAN 2) with the Service Provider VLAN (VLAN 3): T2600G-28TS(config)# switchport dot1q-tunnel replace 2 3 19.9 show dot1q-tunnel Description The show dot1q-tunnel command is used to display the global configuration information of the VLAN VPN. Syntax show dot1q-tunnel - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 173
Mapping entry. Syntax show dot1q-tunnel mapping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of VLAN Mapping entry: T2600G-28TS(config)#show dot1q-tunnel mapping 19.11 show dot1q-tunnel interface Description The show dot1q - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 174
no gvrp command. Syntax gvrp no gvrp Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the GVRP function globally: T2600G-28TS(config)#gvrp 20.2 gvrp (interface) Description The gvrp command is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 175
Ethernet ports 1/0/2-6: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6 T2600G-28TS(config-if-range)#gvrp 20.3 gvrp registration Description The gvrp registration command is used to configure the GVRP registration type for the desired port. To restore to the default value, please use - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 176
Example Configure the GVRP registration mode as "fixed" for Gigabit Ethernet ports 1/0/2-6: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-6 T2600G-28TS(config-if-range)#gvrp registration fixed 20.4 gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 177
of it to the default value: T2600G-28TS(config)#interface gigabitEthernet 1/0/6 T2600G-28TS(config-if)#gvrp timer leaveall 2000 T2600G-28TS(config-if)#no gvrp timer join 20.5 show gvrp interface Description The show gvrp interface command is used to display the GVRP configuration information of - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 178
20.6 show gvrp global Description The show gvrp global command is used to display the global GVRP status. Syntax show gvrp global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global GVRP status: T2600G-28TS(config)#show gvrp global 155 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 179
. Example Enable IGMP Snooping function: T2600G-28TS(config)# ip igmp snooping 21.2 ip igmp snooping version Description The ip igmp snooping version command is used to configure IGMP version globally. To return to the default configuration, please use no ip igmp snooping version command. Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 180
version as v2: T2600G-28TS (config)# ip igmp snooping version v2 21.3 ip igmp snooping drop-unknown Description The ip igmp snooping drop-unknown command is used to configure the way how the switch processes multicast streams that are sent to unknown multicast groups as Discard. By default, it is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 181
header-validation Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IGMP Header Validation: T2600G-28TS(config)# ip igmp snooping header-validation 21.5 ip igmp snooping vlan-config Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 182
the default Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Snooping function and modify Router Port Aging Time as 300 seconds, Member Port Aging Time as 200 seconds for VLAN 1-3: T2600G-28TS(config)# ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 183
from 1 to 4094, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Fast Leave for VLAN 1-3: T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 immediate-leave 21 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 184
, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Report Suppression for VLAN 1-3: T2600G-28TS(config)# ip igmp snooping vlan-config 1-3 report-suppression 21 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 185
will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1 : T2600G-28TS(config)# ip igmp snooping vlan-config 1 router-ports - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 186
T2600G-28TS(config)# ip igmp snooping vlan-config 1-2 rport interface gigabitEthernet 1/0/1 21.10 ip igmp snooping vlan-config (static) Description This command is used to configure to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5. ip --Specify the IP address of the multicast - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 187
T2600G-28TS(config)# ip igmp snooping vlan-config 2 static 225.0.0.1 interface gigabitEthernet 1/0/1-3 21.11 ip igmp snooping , and the default value is 60 seconds. ip-addr-- The source IP address of the general query messages sent by the switch. It should be a unicast address. By default, it is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 188
default value is 1 second. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IGMP Snooping Querier for VLAN 3, and configure the query interval as 100 seconds: T2600G-28TS(config)# ip igmp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 189
default of no limitation on the specified port, please use the no ip igmp snooping max-groups command. To return to the default action of dropping the report, please use the no ip as 10, and configure the throttling action as replace: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5 166 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 190
T2600G-28TS(config-if-range)#ip igmp snooping max-groups 10 T2600G-28TS(config-if-range)#ip igmp snooping max-groups action replace 21.14 ip igmp snooping immediate-leave Description The ip igmp snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 191
RADIUS server is configured. For how to enable AAA function and configure RADIUS server, please refer to aaa enable and radius-server host. Example Enable IGMP authentication on port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ip igmp snooping authentication - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 192
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the profile 1: T2600G-28TS(config)# ip igmp profile 1 21.18 deny Description The deny command is used to configure the filtering mode of profile as deny. Syntax deny Command Mode Profile - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 193
of profile 1 as permit: T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#permit 21.20 range Description The range command is used to configure the range of the profile's filtering multicast address. To delete the corresponding filtering multicast address, please use no range - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 194
access to these commands. Example Configure one of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1: T2600G-28TS(config)# ip igmp profile 1 T2600G-28TS(config-igmp-profile)#range 225.1.1.1 226.3.2.1 21.21 ip igmp filter Description The ip igmp filter command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 195
Clear the statistics of the IGMP packets: T2600G-28TS(config)# clear ip igmp snooping statistics 21.23 show ip igmp snooping Description The show ip igmp snooping command is used to display the global configuration of IGMP snooping. Syntax show ip igmp snooping Command Mode Privileged EXEC Mode and - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 196
Requirement None. Example Display the IGMP baisic configuration configuration of all ports and port channels: T2600G-28TS# show ip igmp snooping interface basic-config Display the IGMP basic configuration of port 1/0/2: T2600G-28TS# show ip igmp snooping interface gigabitEthernet 1/0/2 basic-config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 197
Configuration Mode Privilege Requirement None. Example Display the IGMP snooping configuration information of VLAN 2: T2600G-28TS# show ip igmp snooping vlan 2 21.26 show ip igmp snooping groups Description The show ip all multicast items. multicast_addr -- IP address of the multicast group. count-- - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 198
Display the count of static multicast entries of VLAN 5 T2600G-28TS(config)#show ip igmp snooping groups vlan 5 static count 21.27 show ip igmp profile Description The show ip igmp profile command is used to display the configuration information of all the profiles or a specific profile. Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 199
Parameter id -- Specify the ID of the profile, ranging from 1 to 999. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of all profiles: T2600G-28TS(config)# show ip igmp profile 176 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 200
command. Syntax ipv6 mld snooping no ipv6 mld snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable MLD Snooping: T2600G-28TS(config)# ipv6 mld snooping 22.2 ipv6 mld snooping drop-unknown Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 201
unknown multicast filter function: T2600G-28TS(config)# ipv6 mld snooping vlan-id-list -- The ID list of the VLAN desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5. router are from 60 to 600 in seconds, and the default value is 300 seconds. member-time -- The Member - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 202
Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the MLD Snooping function and modify Router Port Time as 300 seconds, Member Port Time as 200 seconds for VLAN 1-3: T2600G-28TS function is disabled by default. Syntax ipv6 mld - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 203
report-suppression command. This function is disabled by default. Syntax ipv6 mld snooping vlan-config vlan-id- Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the MLD Report Suppression for VLAN 1-3: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 204
port-channels will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Forbid the Ethernet ports 1/0/1-3 as being router ports in VLAN 1: T2600G-28TS(config)# ipv6 mld snooping vlan-config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 205
-list-- The ID of the port channels. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Set the router port as 1/0/1 for VLAN 1-2: T2600G-28TS(config)# ipv6 mld snooping vlan-config 1-2 rport interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 206
desired to modify configuration, ranging from 1 to 4094, in the format of 1-3, 5. ip --Specify the IP address of the multicast Configure port ports 1/0/1-3 in VLAN 2 to statically join multicast group ff80::1234:1: T2600G-28TS restore the default values, please use no ipv6 mld snooping - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 207
ip | last-listener-query-count | last-listener-query-interval ] Parameter vlan-id-list -- The ID list of the VLAN desired to modify configuration, default value is 60 seconds. ip-addr-- The source IP address of the general query messages sent by the switch. It should be a unicast address. By default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 208
Example Enable the MLD Snooping Querier for VLAN 3, and configure the query interval as 100 seconds: T2600G-28TS(config)# ipv6 mld snooping vlan-config 3 querier T2600G-28TS(config)# ipv6 mld snooping vlan-config 3 querier query interval 100 22.10 ipv6 mld snooping (interface) Description The ipv6 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 209
It ranges from 0 to 1000 and the default value is 1000. drop -- When the number address. Command Mode Interface Configuration configure the throttling action as replace: T2600G-28TS(config)#interface range gigabitEthernet 1/0/2-5 T2600G-28TS(config-if-range)#ipv6 mld snooping max-groups 10 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 210
the Fast Leave function for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ipv6 mld snooping immediate-leave 22.13 ipv6 mld profile Description The ipv6 mld profile command is used to create the configuration profile. To delete the corresponding profile - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 211
Operator level users have access to these commands. Example Configure the filtering mode of profile 1 as deny: T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-MLD-profile)#deny 22.15 permit Description The permit command is used to configure the filtering mode of profile as permit. Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 212
Only Admin and Operator level users have access to these commands. Example Configure one of the filter multicast address entry as range ff80::1234 to ff80::1235 in profile 1: T2600G-28TS(config)# ipv6 mld profile 1 T2600G-28TS(config-igmp-profile)#range ff80::1234 ff80::1235 22.17 ipv6 mld filter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 213
these commands. Example Clear the statistics of the MLD packets: T2600G-28TS(config)# clear ipv6 mld snooping statistics 22.19 show ipv6 mld snooping Description The show ipv6 mld snooping command is used to display the global configuration of MLD Snooping. Syntax show ipv6 mld snooping Command Mode - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 214
information selected to display. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MLD baisic configuration configuration of all ports and port channels: T2600G-28TS# show ipv6 mld snooping interface basic-config Display the MLD basic - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 215
EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display all of the VLAN information: T2600G-28TS(config)# show ipv6 mld to display the information of all multicast items. ipv6_multicast_addr -- IPv6 address of the multicast group. count-- The numbers of all multicast - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 216
. static count-- The numbers of all static multicast groups. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display all of the multicast groups: T2600G-28TS(config)# show ipv6 mld snooping groups 22.23 show ipv6 mld profile Description The show ipv6 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 217
. Example Enable MVR globally: T2600G-28TS(config)# mvr 23.2 mvr group Description The mvr group command is used to add multicast groups to MVR. To delete multicast groups from MVR, please use no mvr group command. You can configure up to 511 multicast groups. Syntax mvr group ip-addr [count ] 194 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 218
multicast groups 225.1.2.3 -239.1.2.5 to MVR: T2600G-28TS (config)# mvr group 225.1.2.3 3 23.3 mvr mode Description The mvr mode command is used to configure the MVR mode as compatible or dynamic. By default, it is compatible. To return to the default configuration, please use no mvr mode command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 219
as dynamic: T2600G-28TS(config)# mvr mode dynamic 23.4 mvr querytime Description The mvr querytime command is used to configure the maximum time to wait for IGMP report on a receiver port before removing the port from multicast group membership. To return to the default configuration, please use - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 220
access to these commands. Example Configure the multicast VLAN as VLAN 10: T2600G-28TS(config)# mvr vlan 10 23.6 mvr (interface) Description This command is used to enable MVR for specific interfaces. To disable MVR for the interfaces, please use no mvr command. By default, it is disabled. Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 221
Enable MVR for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#mvr 23.7 mvr type Description The mvr type command is used to configure the MVR port type as receiver or source. By default, the port is a non-MVR port. If you attempt to configure a non-MVR port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 222
Mode Interface Configuration Mode ( T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#mvr immediate 23.9 mvr vlan (group) Description This command is used to statically add ports to an MVR group. Then the ports can receive multicast traffic sent to the IP multicast address - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 223
225.1.2.3 statically. The multicast VLAN is VLAN 10: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)#mvr vlan 10 group 225.1.2.3 23.10 show mvr Description The show mvr command is used to display the global configuration of MVR. Syntax show mvr Command Mode Privileged - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 224
Display the MVR configuration of port 1/0/3: T2600G-28TS# show mvr interface gigabitEthernet 1/0/3 23.12 show mvr members Description The show mvr members command is used to display the membership information of all MVR groups or the specified MVR group. Syntax show mvr members [ ip-addr ] [ status - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 225
Example Display the membership information of all MVR groups: T2600G-28TS# show mvr members 202 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 226
disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths. 24.1 debug spanning debug messages. flush -- Display the address table flushing debug messages. init -- state -- Display the MSTP interface state change debug messages. tc -- Display the MSTP - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 227
. Syntax spanning-tree no spanning-tree Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the STP function: T2600G-28TS(config)# spanning-tree 24.3 spanning-tree (interface) Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 228
1/0/2 T2600G-28TS(config-if)# spanning-tree 24.4 spanning-tree common-config Description The spanning-tree common-config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances. To return to the default configuration, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 229
1/0/1 T2600G-28TS(config-if)# spanning-tree common-config port-priority 64 ext-cost 100 int-cost 100 portfast enable point-to-point open 24.5 spanning-tree mode Description The spanning-tree mode command is used to configure the STP mode of the switch. To return to the default configurations, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 230
users have access to these commands. Example Enter into the MST configuration mode: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(Config-mst)# 24.7 instance Description The instance command is used to configure the VLAN-Instance mapping. To remove the VLAN-instance mapping or - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 231
1, namely remove all the mapping VLANs 1-100: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(config-mst)# no instance 1 Remove VLANs 1-50 in mapping VLANs 1-100 for Instance 1: T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(config-mst)# no instance 1 vlan 1-50 24 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 232
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the region name of MST as "region1": T2600G-28TS(config)# spanning-tree mst configuration T2600G-28TS(config-mst)# name region1 24.9 revision Description The revision command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 233
the MST Instance 1 and configure its priority as 4096: T2600G-28TS(config)# spanning-tree mst instance 1 priority 4096 24.11 spanning-tree mst Description The spanning-tree mst command is used to configure MST Instance Port. To return to the default configuration of the corresponding Instance Port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 234
as 2000: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# spanning-tree mst instance 1 port-priority 64 cost 2000 24.12 spanning-tree priority Description The spanning-tree priority command is used to configure the bridge priority. To return to the default value of bridge - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 235
the bridge priority as 4096: T2600G-28TS(config)# spanning-tree priority 4096 24.13 spanning-tree timer Description The spanning-tree timer command is used to configure forward-time, hello-time and max-age of Spanning Tree. To return to the default configurations, please use no spanning-tree - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 236
, ranging from 1 to 20 in pps. By default, it is 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the hold-count of STP as 8pps: T2600G-28TS(config)# spanning-tree hold-count 8 24.15 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 237
discarded, ranging from 1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max-hops of STP as 30: T2600G-28TS(config)# spanning-tree max-hops 30 24.16 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 238
tree bpduflood no spanning-tree bpduflood Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / the BPDU forward function for port 1/0/2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# spanning-tree bpduflood 24.18 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 239
1/0/2 T2600G-28TS(config-if)# spanning-tree bpduguard 24.19 spanning-tree guard loop Description The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 240
the Root Protect function for port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# spanning-tree guard root MAC address entries, which may decrease the performance and stability of the network. With the Protect of Spanning Tree function enabled, you can configure the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 241
Tree for port 2: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# spanning-tree guard tc 24.22 spanning-tree mcheck Description The spanning-tree mcheck command is used to enable mcheck. Syntax spanning-tree mcheck Command Mode Interface Configuration Mode (interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 242
-count | max-age | max-hops | mode | priority | state ] Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bridge parameters: T2600G-28TS(config)# show spanning-tree bridge 24.25 show spanning-tree interface Description The show spanning-tree - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 243
number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the spanning-tree information of all ports: T2600G-28TS(config)# show spanning-tree interface Display the spanning-tree information of port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 244
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the protect information of all ports: T2600G-28TS(config)# show spanning-tree interface-security Display the protect information of port 1: T2600G-28TS(config)# show spanning-tree interface-security - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 245
Display the related information of MST Instance 1: T2600G-28TS(config)#show spanning-tree mst instance 1 Display all the ports information of MST Instance 1: T2600G-28TS(config)#show spanning-tree mst instance 1 interface 222 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 246
lldp command. Syntax lldp no lldp Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable LLDP function globally: T2600G-28TS(config)#lldp 25.2 lldp forward_message Description The lldp forward_message - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 247
the Hold Multiplier parameter. It ranges from 2 to 10. By default, it is 4. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify Hold Multiplier as 5: T2600G-28TS(config)#lldp hold-multiplier 5 224 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 248
LLDPDU to its neighbors. The value ranges from 5 to 32768 and the default value is 30 seconds. tx-delay -- Configure a value from 1 to 8192 in seconds to specify the time for the local device to transmit LLDPDU to its neighbors after changes occur so as to prevent LLDPDU being sent frequently. By - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 249
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable port 1/0/1 to receive LLDPDU: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 250
Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the SNMP notification for Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 251
Gigabit Ethernet port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# no lldp tlv-select management-address port-vlan 25.9 lldp management-address Description The lldp management-address command is used to configure the port's management address to be included in - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 252
Configure the port's management address as 192.168.1.100 for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# lldp management-address based on this parameter. The default value is 4. To return to the default configuration, please use no lldp med-fast - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 253
1/0/2 T2600G-28TS(config-if)# lldp med-status 25.12 lldp med-tlv-select Description The lldp med-tlv-select command is used to configure LLDP-MED TLVs to be included in outgoing LLDPDU for the corresponding port. To exclude LLDP-MED TLVs, please use no lldp med-tlv-select command. By default, All - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 254
T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# no lldp med-tlv-select network-policy inventorymanagement 25.13 lldp med-location Description The lldp med-location command is used to configure emergency-number -- Emergency Call Service ELIN identifier, which is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 255
the Location Identification TLV's content in outgoing LLDPDU of port 1/0/2. Configure the language as English and city as London: T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# lldp med-location civic-address language English lci-city London 25.14 show lldp Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 256
the LLDP configuration of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp interface gigabitEthernet 1/0/1 25.16 show lldp local-information interface Description The show lldp local-information interface command is used to display the LLDP information of the corresponding port. By default, the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 257
used to display the neighbor information of the corresponding port. By default, the neighbor information of all the ports will be displayed. and Any Configuration Mode Privilege Requirement None. Example Display the neighbor information of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp neighbor - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 258
Privilege Requirement None. Example Display the LLDP statistic information of Gigabit Ethernet port 1/0/1: T2600G-28TS#show lldp traffic interface gigabitEthernet 1/0/1 235 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 259
service providers to transmit packets from different customers across their ISP networks and maintain Layer 2 protocol configurations of each customer. The supported T2600G-28TS(config)# l2protocol-tunnel 26.2 l2protocol-tunnel type Description The l2protocol-tunnel type command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 260
MAC address of Cisco PVST+ BPDUs. ■ gvrp: Enable protocol tunneling for the GVRP packets. ■ stp: Enable protocol tunneling for the STP packets. ■ lacp: Enable protocol tunneling for the LACP packets. ■ all: All the above Layer 2 protocols are supported for tunneling. ■ threshold --Configure the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 261
Only Admin and Operator level users have access to these commands. Example Configure port 1/0/3 as a UNI port for STP packets with the threshold as 1000 packets/second: T2600G-28TS(config)#interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# l2protocol-tunnel type uni stp threshold 1000 26.3 show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 262
Requirement None. Example Display the L2PT configuration information of Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#show l2protocol-tunnel interface gigabitEthernet 1/0/1 Display the L2PT configuration information of all Ethernet ports: T2600G-28TS(config)#show l2protocol-tunnel interface 239 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 263
-insertion command. Syntax pppoe id-insertion no pppoe id-insertion Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the PPPoE ID-Insertion function: T2600G-28TS(config)# pppoe id-insertion 240 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 264
T2600G-28TS (config)# interface gigabitEthernet 1/0/1 T2600G-28TS (config-if)# pppoe circuit-id 27.3 pppoe circuit-id type Description The pppoe circuit-id type command is used to configure the type of PPPoE Circuit-ID for a specified port. By default, the PPPoE Circuit-ID type is "ip". Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 265
ip: The IP address of the switch will be used to encode the Circuit-ID option. This is the default value. udf: A user specified . Example Configure the type of PPPoE Circuit-ID as "mac" for the Gigabit Ethernet port 1/0/1: T2600G-28TS (config)# interface gigabitEthernet 1/0/1 T2600G-28TS (config-if - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 266
Admin, Operator and Power User level users have access to these commands. Example Configure the remote-ID as "mac" for the Gigabit Ethernet port 1/0/1: T2600G-28TS (config)# interface gigabitEthernet 1/0/1 T2600G-28TS (config-if)# pppoe remote-id mac 27.5 show pppoe id-insertion global Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 267
information of PPPoE Circuit-ID Insertion function of all Ethernet ports: T2600G-28TS# show pppoe id-insertion interface Display the configuration of PPPoE Circuit-ID Insertion function of the Gigabit Ethernet port 1/0/1 : T2600G-28TS# show pppoe id-insertion interface gigabitEthernet 1/0/1 244 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 268
the no ip routing command. Syntax ip routing no ip routing Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable IPv4 routing feature for the switch: T2600G-28TS(config)# ip routing 28.2 interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 269
interface, ranging from 1 to 64. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the loopback interface 1: T2600G-28TS(config)# interface loopback 1 28.4 switchport Description This switchport - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 270
, ranging from 1 to 14, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the port-channel interfaces 1, 3, 4 and 5: T2600G-28TS(config)# interface port-channel 1,3-5 247 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 271
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add a Description system-if to the routed port 1/0/9 : T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 272
Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Shut down the routed port 1/0/9: T2600G-28TS(config)# interface gigabitEthernet 1/0/9 T2600G-28TS(config-if)# no switchport T2600G-28TS(config-if - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 273
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a static route with the destination IP address as 192.168.2.0, the subnet mask as 255.255.255.0 and the next-hop address as 192.168.0.2: T2600G-28TS(config)# ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 274
is. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a static route with the destination network IP address as 3200::/64 and the next-hop address as 3100::1234: T2600G-28TS(config)# ipv6 route - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 275
The VLAN ID. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of VLAN 2: T2600G-28TS(config)#show interface vlan 2 28.13 show ip interface Description This show ip interface command is used to display the detailed information of - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 276
brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the summary information of the Layer 3 interfaces: T2600G-28TS(config)# show ip interface brief 28.15 show ip route Description This show ip route command is used to display the route - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 277
Mode and Any Configuration Mode Privilege Requirement None. Example Display the static routes: T2600G-28TS(config)# show ip route static 28.16 show ip route specify Description This show ip route specify command is used to display the valid routing information to the specified IP address or network - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 278
information of route entries: T2600G-28TS(config)# show ip route summary 28.18 show ipv6 interface Description This command is used to display the configured IPv6 information of the management interface, including ipv6 function status, link-local address and global address, IPv6 multicast groups etc - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 279
. static: The static routes. connected: The connected routes. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IPv6 static routes: T2600G-28TS(config)# show ipv6 route static 28.20 show ipv6 route summary Description This show ipv6 route - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 280
Privilege Requirement None. Example Display the summary information of IPv6 route entries: T2600G-28TS(config)# show ipv6 route summary 257 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 281
before the IPv6 address configuration management. By default it is Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IPv6 function on the VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 282
automatic configuration of the ipv6 link-local address on VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address autoconfig 29.3 ipv6 address link-local Description The ipv6 address link-local command is used to configure the ipv6 link-local address manually on - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 283
users have access to these commands. Example Configure the link-local address as fe80::1234 on the VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address fe80::1234 link-local 29.4 ipv6 address dhcp Description The ipv6 address dhcp command is used to enable the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 284
automatic ipv6 address configuration function to obtain IPv6 address through the RA message on VLAN interface 1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address ra 29.6 ipv6 address eui-64 Description This command is used to manually configure a global IPv6 address with an - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 285
the network prefix 3ffe::/64: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address 3ffe::/64 eui-64 29.7 ipv6 address Description This command is used to manually configure a global IPv6 address on the interface. To remove a global IPv6 address from the interface, please use - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 286
1: T2600G-28TS(config)# interface vlan 1 T2600G-28TS(config-if)# ipv6 address 3001::1/64 29.8 show ipv6 interface Description This command is used to display the configured ipv6 information of the management interface, including ipv6 function status, link-local address and global address, ipv6 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 287
ARP. A static ARP entry is manually configured and maintained. 30.1 arp Description This arp command is used to add a static ARP entry. To delete the specified ARP entry, please use the no arp command. Syntax arp ip mac type no arp ip type Parameter ip -- The IP address of the static ARP entry. mac - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 288
to these commands. Example Clear all the dynamic ARP entries: T2600G-28TS(config)# clear arp-cache 30.3 arp dynamicrenew Description This arp dynamicremew command. By default, it is enabled. Syntax arp dynamicrenew no arp dynamicrenew Command Mode Global Configuration Mode Privilege Requirement Only - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 289
1 to 3000 seconds. The default value is 600 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the ARP aging time as 60 seconds on interface 1/0/1: T2600G-28TS(config-if)# arp timeout - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 290
EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Enable the switch's Layer 3 interface to send gratuitous ARP packets when receiving a gratuitous packets of which the IP address is the same as its own: T2600G-28TS(config)# gratuitous-arp dup-ip-detected enable 30.7 gratuitous - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 291
gratuitous-arp learning enable Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Enable the Layer 3 interface to learn MAC addresses from the gratuitous ARP packets: T2600G-28TS(config)# gratuitous-arp learning enable 30.8 gratuitous-arp send-interval - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 292
Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement None Example Enable the Proxy ARP function on VLAN Interface 2: T2600G-28TS(config)# interface vlan 2 T2600G-28TS(config-if)# ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 293
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement None Example Enable the Local Proxy ARP function on VLAN Interface 2: T2600G-28TS(config)# interface vlan 2 T2600G-28TS(config-if)# ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 294
ID. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the ARP entry associated with VLAN interface 2: T2600G-28TS(config)# show ip arp vlan 2 30.13 show ip arp summary Description This show ip arp summary command is used to display the number - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 295
show gratuitous-arp Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of gratuitous ARP: T2600G-28TS(config)# show gratuitous-arp 30.15 show ip proxy-arp Description The show ip proxy-arp command is used to display the Proxy - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 296
Privilege Requirement None Example Display the Proxy ARP status: T2600G-28TS(config)# show ip proxy-arp 273 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 297
. Example Enable DHCP server service globally: T2600G-28TS(config)# service dhcp server 31.2 ip dhcp server extend-option capwap-ac-ip Description The ip dhcp server extend-option capwap-ac-ip command is used to specify the Option 138, which should be configured as the management IP address of an AC - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 298
Set the remote DHCP server's IP address as 192.168.3.1: T2600G-28TS(config)# ip dhcp server extend-option capwap-ac-ip 192.168.3.1 31.3 ip dhcp server extend-option vendor-class-id Description The ip dhcp server extend-option vendor-class-id command is used to configure the class ID of the packets - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 299
if the end IP address and the start IP address are the same. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Set the reserved IP addresses from 192.168.1.1 to 192.168.1.9: T2600G-28TS(config)# ip dhcp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 300
to 8 characters. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create the address pool of name POOL1: T2600G-28TS(config)# ip dhcp server pool POOL1 31.6 ip dhcp server ping timeout Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 301
packets' number, ranging from 0 to 10. By default it's 1. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the PING packets' number as 2: T2600G-28TS(config)# ip dhcp server ping packets 2 278 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 302
Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool "product" as 192.168.1.0 255.255.255.0: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# network - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 303
Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the lease time of address pool "product" as 10 minutes: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# lease 10 31.10 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 304
as abc in ASCII: T2600G-28TS(config)# ip dhcp pool product T2600G-28TS(dhcp-config)# address 192.168.0.10 client-identifier abc ascii 31.12 default-gateway Description The default-gateway command is used to specify the default gateway of the address pool. To delete the configuration, please use no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 305
192.168.0.1 and 192.168.1.1: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(dhcp-config)# default-gateway 192.168.0.1,192.168.1.1 31.13 dns-server Description The dns-server command is used to specify the DNS server of the address pool. To delete this configuration, please use no dns - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 306
Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool's Netbios servers as 192.168.0.1 and 192.168.1.1: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# netbios - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 307
p-node. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the address pool's Netbios server type as b-node: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# netbios-node - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 308
the DHCP client. Command Mode DHCP Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the DHCP client's domain name as edu: T2600G-28TS(config)# ip dhcp server pool product T2600G-28TS(config-dhcp)# domain-name edu - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 309
status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the status of DHCP service: T2600G-28TS(config)# show ip dhcp server status 31.20 show ip dhcp server statistics Description The show ip dhcp server statistics command is used to display - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 310
None. Example Display the configurations of the remote DCHP servers: T2600G-28TS(config)# show ip dhcp server extend-option 31.22 show ip dhcp server pool Description The show ip dhcp server pool command is used to display the configuration of the address pool. Syntax show ip dhcp server pool 287 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 311
the configured reserved addresses: T2600G-28TS(config)# show ip dhcp server excluded-address 31.24 show ip dhcp server manual-binding Description The show ip dhcp server manual-binding command is used to display the configuration of static binding address. Syntax show ip dhcp server manual-binding - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 312
the configured static binding address: T2600G-28TS(config)# show ip dhcp server manual-binding 31.25 show ip dhcp server binding Description The show ip dhcp server binding command is used to display the binding entries. Syntax show ip dhcp server binding [ ip ip-address ] Parameter ip-address - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 313
binding [ ip-address ] Parameter ip-address -- Specify the binding IP address. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Clear all the binding addresses: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 314
command. Syntax service dhcp relay no service dhcp relay Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable DHCP Relay function globally: T2600G-28TS(config)# service dhcp relay 32.2 ip dhcp relay - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 315
1 to 16, and the default value is 4. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of relay hops as 6: T2600G-28TS(config)# ip dhcp relay hops 6 32.3 ip dhcp relay time - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 316
Configure the DHCP Relay time as 30 seconds: T2600G-28TS(config)# ip dhcp relay time 30 32.4 ip helper-address Description The ip helper-address command is used to add DHCP Server address to the Layer 3 interface. To delete the server address, please use no ip helper-address command. Syntax ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 317
access to these commands. Example Enable option 82 support in DHCP Relay for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp relay information 32.6 ip dhcp relay information strategy Description The ip dhcp relay information strategy command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 318
-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp relay information strategy replace 32.7 ip dhcp relay information format Description The ip dhcp relay information format command is used to select the format of option 82 sub-option value field. To restore to the default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 319
commands. Example Specify the circuit ID as "TP-Link" for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp relay information circuit-id TP-Link 32.9 ip dhcp relay information remote-id Description The ip dhcp relay information remote-id command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 320
remote ID as "TP-Link" for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp relay information remote-id TP-Link 32.10 ip dhcp relay default-interface Description The ip dhcp relay default-interface command is used to configure default relay agent interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 321
Add DHCP server address 192.168.2.1 to VLAN 1: T2600G-28TS(config)# ip dhcp relay vlan 1 helper-address 192.168.2.1 32.12 show ip dhcp relay Description The show ip dhcp relay command is used to display the global status and Option 82 configuration of DHCP Relay. Syntax show ip dhcp relay Command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 322
Privilege Requirement None. Example Display the configuration of DHCP Relay: T2600G-28TS(config)# show ip dhcp relay 299 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 323
use no ip dhcp l2relay command. Syntax ip dhcp l2relay no ip dhcp l2relay Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable DHCP L2 Relay function globally: T2600G-28TS(config)# ip dhcp l2relay - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 324
to these commands. Example Enable option 82 support in DHCP Relay for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp l2relay information 33.4 ip dhcp l2relay information strategy Description The ip dhcp l2relay information strategy command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 325
1/0/2 T2600G-28TS(config-if)# ip dhcp l2relay information strategy replace 33.5 ip dhcp l2relay information format Description The ip dhcp l2relay information format command is used to select the format of option 82 sub-option value field. To restore to the default option, please use no ip dhcp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 326
the value you configure for the related sub-option. Command Mode Interface Configuration Mode (interface gigabitEthernet T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ip dhcp l2relay information format normal 33.6 ip dhcp l2relay information circuit-id Description The ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 327
ID as "TP-Link" for port 2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)# ip dhcp l2relay information remote-id TP-Link 33.8 show ip dhcp l2relay Description The show ip dhcp l2relay command is used to display the global status and Option 82 configuration of DHCP Relay - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 328
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of DHCP L2 Relay: T2600G-28TS(config)# show ip dhcp l2relay 33.9 show ip dhcp l2relay interface Description The show ip dhcp l2relay interface command is used to display the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 329
Description The qos trust mode command is used to configure the trust mode of CoS (Class of Service) function for the ports. The default trust mode is trust port priority. Syntax qos trust as dscp: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# qos trust mode dscp 306 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 330
the priority of port 5 as 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# qos port-priority 3 34.3 qos cos-map Description The qos cos-map command is used to configure 802.1p to queue mapping globally. To return to the default configuration, please use no qos cos-map - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 331
. Example Map the 802.1p priority 5 to TC-2: T2600G-28TS (config)# qos cos-map 5 2 34.4 qos dot1p-remap Description The qos dot1p-remap command is used to configure the 802.1p to 802.1p mappings for the ports. To return to the default configuration, please use no qos dot1p-remap command. When 802 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 332
1/0/1 T2600G-28TS(config-if)#qos dot1p-remap 5 6 34.5 qos dscp-map Description The qos dscp-map command is used to configure the DSCP to 802.1p mapping. To return to the default configuration, please use no qos dscp-map command. DSCP (DiffServ Code Point) is a new definition to IP ToS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 333
priority 2 for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#qos dscp-map 5 2 34.6 qos dscp-remap Description The qos dscp-remap command is used to configure the DSCP to DSCP mappings for the ports. To return to the default configuration, please use no qos - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 334
(For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The qos queue bandwidth command is used to configure the minimum guaranteed bandwidth allocated to the specified queue. A value of 0 means there is no guaranteed minimum bandwidth in effect (best-effort service). The default value - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 335
T2600G-28TS(config-if)# qos queue 5 bandwidth 10 34.8 qos queue mode Description The qos queue mode command is used to configure the Scheduler Mode. When the network is congested, the program that many packets complete for resources must be solved, usually in the way of queue - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 336
-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the 802.1p to queue mappings: T2600G-28TS# show qos cos-map 34.10 show qos dot1p-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dot1p-remap - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 337
Mode Privilege Requirement None. Example Display the IEEE 802.1P remap configuration: T2600G-18TS# show qos dot1p-remap 34.12 show qos dscp-map interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dscp-map interface command is used to display the DSCP - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 338
-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DSCP priority configuration: T2600G-18TS# show qos dscp-map 34.14 show qos dscp-remap interface (For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS) Description The show qos dscp-remap - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 339
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DSCP to DSCP mappings for all the ports: T2600G-28TS# show qos dscp-remap interface 34.15 show qos dscp-remap (For T2600G-18TS) Description The show qos dscp-remap command is used to display - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 340
. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the trust mode of all the ports: T2600G-28TS# show qos trust interface 34.18 show qos queue interface Description The show qos queue interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 341
-channel port-channel-id ] Parameter port -- The port number. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the scheduler settings of all the ports: T2600G-28TS# show qos queue interface 318 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 342
The storm-control rate-mode command is used to configure the storm control mode of the interface. To return to the default configuration, please use no storm-control rate-mode command. Syntax For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: storm-control rate-mode { kbps | ratio | pps } no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 343
1/0/5 T2600G-28TS(config-if)# storm-control rate-mode pps 35.2 storm-control Description The storm-control command is used to enable the broadcast, multicast, or unknown unicast strom control function and to set threshold levels on an interface. To return to the default configuration, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 344
T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# storm-control rate-mode kbps T2600G-28TS(config-if)# storm-control broadcast 1024 35.3 storm-control exceed Description The storm-control exceed command is used to configure 0 to 3600 and the default value is 0. When the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 345
users have access to these commands. Example Recover port 1/0/5 manually: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# storm-control recover 35.5 bandwidth Description The bandwidth command is used to configure the bandwidth limit for an Ethernet port. To disable the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 346
Admin, Operator and Power User level users have access to these commands. Example Configure the ingress-rate as 5120Kbps and egress-rate as 1024Kbps for port 1/0/5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# bandwidth ingress 5120 egress 1024 35.6 show storm-control - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 347
list of Ethernet ports. port-channel-id-list -- The list of port channels. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bandwidth-limit information of port 1/0/4: T2600G-28TS(config)# show bandwidth interface gigabitEthernet 1/0/4 324 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 348
VLAN ID, ranging from 2 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Voice VLAN function for VLAN 10: T2600G-28TS(config)# voice vlan 10 36.2 voice vlan (interface) Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 349
VLAN function for port 1/0/1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#voice vlan 36.3 voice vlan priority Description The voice vlan priority command is used to configure the priority for the Voice VLAN. To restore to the default priority, please use no voice - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 350
OUI described as TP-Phone with the OUI address 00:11:11:11:11:11 and the mask address FF:FF:FF:00:00:00: T2600G-28TS(config)#voice vlan oui 00:11:11 oui-desc TP-Phone 36.5 show voice vlan Description The show voice vlan command is used to display the global configuration information of - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 351
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the configuration information of Voice VLAN globally: T2600G-28TS(config)# show voice vlan 36.6 show voice vlan oui-table Description The show voice vlan oui command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 352
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the Voice VLAN configuration information of all ports and port channels: T2600G-28TS(config)# show voice vlan interface 329 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 353
, this feature can help ensure that the sound quality of an IP phone does not deteriorate when data traffic on the port is heavy auto-voip no auto-voip Command Mode Global Configuration Mode Example Enable the Auto VoIP function globally: T2600G-28TS(config)# auto-voip 37.2 auto-voip (interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 354
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Example Set Auto VoIP VLAN 3 for port 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# auto-voip 3 37.3 auto- - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 355
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Example Set the interface mode as untagged for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# auto - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 356
Disable the Auto VoIP function on port 1/0/3: T2600G-52TS(config)# interface gigabitEthernet 1/0/3 T2600G-52TS(config-if)# no auto-voip 37.7 ports. It ranges from 0 to 63. By default, it is 0. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 357
Override Mode as trust for port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# auto-voip data priority trust 37.9 show auto-voip Description The show auto-voip command is used to display the Auto VoIP configuration information. Syntax show auto-voip [ interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 358
the Auto VoIP configuration information of ports. When no parameter is entered, displays the global Auto VoIP configuration information. Command Mode Privileged EXEC Mode and any Configuration Mode Example Displays the global Auto VoIP configuration information: T2600G-28TS (config)# show auto - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 359
level users have access to these commands. Example Configure the access control mode as IP-based: T2600G-28TS(config)# user access-control ip-based enable 38.2 user access-control ip-based Description The user access-control ip-based command is used to limit the IP-range of the users for login. Only - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 360
enabled by default. id -- Delete the specified IP-based entry. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the access-control of the user whose IP address is 192.168.0.148: T2600G-28TS(config)# user - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 361
entry to be deleted. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to login: T2600G-28TS(config)# user access-control mac-based 00 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 362
Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the access control mode as Port-based: T2600G-28TS(config)# user access-control port-based enable 38.6 user access-control port-based Description The user access-control port-based - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 363
by default. id-- Specify the ID of the port-based entry to be deleted. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the users connected to ports 2-6 are allowed to login: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 364
by default. The HTTP and HTTPS server function can be disabled at the same time. Syntax ip http server no ip http server Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable the HTTP function: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 365
users have access to these commands. Example Set the port number of HTTP server as 1800: T2600G-28TS(config)# ip http port 1800 39.3 ip http max-users Description The ip http max-users command is used to configure the maximum number of users that are allowed to connect to the HTTP server. To cancel - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 366
on to the HTTP server as 1, 2, 3 and 4 respectively: T2600G-28TS(config)# ip http max-users 1 2 3 4 39.4 ip http session timeout Description The ip http session timeout command is used to configure the connection timeout of the HTTP server. To restore to the default timeout time, please use no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 367
Disable the HTTP function: T2600G-28TS(config)# no ip http secure-server 39.6 ip http secure-port Description The ip http secure-port command is used to configure the port number of the HTTPS server within the switch. To set the number to the default value, please use no ip http secure-port command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 368
as 2800: T2600G-28TS(config)# ip http port 2800 39.7 ip http secure-protocol Description The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports all the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 369
connection as SSL 3.0: T2600G-28TS(config)# ip http secure-protocol ssl3 39.8 ip http secure-ciphersuite Description The ip http secure-ciphersuite command is used to configure the cipherSuites over the SSL connection supported by the switch. To restore to the default ciphersuite types, please use - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 370
than 16. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum number of the Admin, Operator, Power User and User as 5, 1, 1, 1 for HTTPs: T2600G-28TS(config)# ip http secure-max-users - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 371
in minutes. By default, the value is 10. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the timeout time of the HTTPs connection as 15 minutes: T2600G-28TS(config)# ip http secure-session - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 372
. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Download an SSL Certificate named ssl-cert from TFTP server with the IP address of 192.168.0.146: T2600G-28TS(config)# ip http secure-server download - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 373
key ssl-key ip-address 192.168.0.146 Download an SSL key named ssl-key from TFTP server with the IP address of fe80::1234 T2600G-28TS(config)# ip http secure-server download key ssl-key ip-address fe80::1234 39.13 show ip http configuration Description The show ip http configuration command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 374
secure-server command is used to display the global configuration of SSL. Syntax show ip http secure-server Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of SSL: T2600G-28TS(config)# show ip http secure-server 351 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 375
to these commands. Example Enable the SSH function: T2600G-28TS(config)# ip ssh server 40.2 ip ssh port Description The ip ssh port command is used to configure the port for SSH service. To set the value to the default, please use no ip ssh port command. Syntax ip ssh port port no ip ssh port 352 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 376
from 1 to 65535. The default value is 22. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the SSH port number as 22: T2600G-28TS(config)# ip ssh port 22 40.3 ip ssh version Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 377
as AES128-CBC: T2600G-28TS(config)# ip ssh algorithm AES128-CBC 40.5 ip ssh timeout Description The ip ssh timeout command is used to specify the idle-timeout time of SSH. To restore to the factory defaults, please use ip ssh timeout command. Syntax ip ssh timeout value no ip ssh timeout Parameter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 378
as 30 seconds: T2600G-28TS(config)# ip ssh timeout 30 40.6 ip ssh max-client Description The ip ssh max-client command is used to specify the maximum number of the connections to the SSH server. To return to the default configuration, please use no ip ssh max-client command. Syntax ip ssh max-client - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 379
Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Download an SSH-1 type key file named ssh-key from TFTP server with the IP address 192.168.0.148: T2600G-28TS(config)# ip ssh download v1 ssh-key ip-address 192 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 380
40.9 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH. Syntax show ip ssh Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of SSH: T2600G-28TS(config)# show ip ssh 357 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 381
with the IP address of 192.168.0.10: T2600G-28TS# telnet 192 .168.0.10 41.2 telnet enable Description The telnet enable command is used to enable the Telnet function. To disable the Telnet function, please use the telnet disable command. This function is enabled by default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 382
Only Admin and Operator level users have access to these commands. Example Disable the Telnet function: T2600G-28TS(config)# telnet disable 41.3 telnet port Description The telnet port command is used to configure the telent port number. To restore the setting, please use the no telnet port command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 383
Syntax show telnet-status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display whether the Telnet function is enabled: T2600G-28TS(config)# show telnet-status 360 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 384
console port. The default baul rate is 38400 bps. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify the communication baud rate on the console port to the default value: T2600G-28TS(config)# no serial_port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 385
-server host Description The tacacs-server host command is used to configure a new TACACS+ server. To delete the specified TACACS+ server, please use no tacacs-server host command. Syntax tacacs-server host ip-address [ port port-id ] [ timeout time ] [ key { [ 0 ] string | 7 encryped-string } ] no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 386
are added in the server group "tacacs" by default. Example Configure a TACACS+ server with the IP address as 1.1.1.1, TCP port as 1500, timeout as 6 seconds, and the unencrypted key string as 12345. T2600G-28TS(config)# tacacs-server host 1.1.1.1 port 1500 timeout 6 key 12345 43.2 show tacacs - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 387
the TACACS+ servers: T2600G-28TS(config)# show tacacs-server 43.3 radius-server host Description The radius-server host command is used to configure a new RADIUS server. To delete the specified RADIUS server, please use no radius-server host command. Syntax radius-server host ip-address [ auth-port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 388
are added in the server group "radius" by default. Example Configure a RADIUS server with the IP address as 1.1.1.1, authentication port as 1200, timeout as 6 seconds, retransmit times as 3, and the unencrypted key string as 12345. T2600G-28TS(config)# radius-server host 1.1.1.1 auth-port 1200 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 389
type as RADIUS or TACACS+. group-name -- Specify the server group name. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create a RADIUS server group with the name radius1: T2600G-28TS(config)# aaa group radius radius1 366 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 390
ip-address no server ip-address Parameter ip-address -- Specify the server's IP address. Command Mode Server Group Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create the RADIUS server 1.1.1.1 to RADIUS server group "radius1": T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 391
to these commands. Example Display the information of all the server groups: T2600G-28TS(config)# show aaa group 43.8 aaa authentication login Description This aaa authentication login command is used to configure a login authentication method list. A method list describes the authentication methods - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 392
to these commands. User Guidelines By default the login authentication method list is "default" with "local" as method1. Example Configure a login authentication method list "list1" with the priority1 method as radius and priority2 method as local: T2600G-28TS(config)# aaa authenticaiton login list1 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 393
group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1x authentication method as "radius1": T2600G-28TS(config)# aaa authentication - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 394
server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1x accounting method as "radius1": T2600G-28TS(config)# aaa accounting - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 395
to these commands. Example Display the information of the default 802.1x accounting method list: T2600G-28TS(config)# show aaa accounting 43.14 line telnet Description The line telnet command is used to enter the Line Configuration Mode to configure the telnet terminal line to which you want to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 396
" by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the telnet terminal line as "list1": T2600G-28TS(config)#line telnet T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 397
Enter the ssh terminal line configuration mode: T2600G-28TS(config)#line ssh 43.17 login authentication (ssh) Description The login authentication command is used to apply the login authentication method list to the ssh terminal line. To restore to the default authentication method list, please use - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 398
console 0 terminal line configuration mode: T2600G-28TS(config)#line console 0 43.19 login authentication (console) Description The login authentication command is used to apply the login authentication method list to the console terminal line. To restore to the default authentication method list - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 399
It is "default" by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the console 0 terminal line as "list1": T2600G-28TS(config)# line - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 400
by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the ssh terminal line as "list2": T2600G-28TS(config)# line ssh T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 401
It is "default" by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the console 0 terminal line as "list2": T2600G-28TS(config)# line - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 402
. It is "default" by default, which contains the method "local". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the HTTP access as "list1": T2600G-28TS(config)# ip http login - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 403
Example Configure the enable authentication method list on the HTTP access as "list2": T2600G-28TS(config)# ip http enable T2600G-28TS(config)# show aaa global 43.26 enable admin password Description The enable admin password command is used to set or change the Enable password for users to change - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 404
configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration configured password will take effect. Example Set the Enable password as "abc123" and unencrypted for users to change the access level to admin: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 405
characters are By default, it is empty. The password in the configuration file will be configured password will take effect. Example Set the Enable password as "abc123" and unencrypted for users to change the access level to admin. The password will be displayed in the encrypted form. T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 406
Syntax enable-admin Command Mode Privileged EXEC Mode Privilege Requirement Only User, Power User and Operator level users have access to these commands. Example Get the administrative privilege (the Enable password is "123456"): T2600G-28TS# enable-admin Password: 123456 383 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 407
the supplicant. It is usually an 802.1x-supported network device, such as this TP-Link switch. It acts as an intermediary (proxy Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the IEEE 802.1x function: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 408
commands. Example Disable the 802.1x handshake function: T2600G-28TS(config)# no dot1x handshake 44.3 dot1x auth-protocol Description The dot1x auth-protocol command is used to configure the authentication protocol of IEEE 802.1x and the default 802.1x authentication method is "eap". To restore - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 409
access to these commands. Example Configure the Authentication protocol of IEEE 802.1x as "pap": T2600G-28TS(config)#dot1x auth-protocol pap create the related VLAN automatically, add the authenticated port to the VLAN and change the PVID based on the assigned VLAN. If the assigned VLAN exists on - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 410
vlan-assignment no dot1x vlan-assignment Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the VLAN assignment feature: T2600G-28TS(config)#dot1x vlan-assignment 44.5 dot1x accounting Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 411
frame with the client's MAC address as the username and password. It is also necessary to configure the RADIUS server with the client T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config)#dot1x mab 44.7 dot1x guest-vlan Description The dot1x guest-vlan command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 412
Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the Guest VLAN function for VLAN 5 and set the VLAN ID as 20 on the Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 413
Ethernet port 1/0/1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config)#dot1x quiet-period 5 44.9 dot1x timeout supp-timeout Description The dot1x timeout supp-timeout command is used to configure the supplicant timeout on the port. To restore to the default, please use no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 414
gigabitEthernet 1/0/1 T2600G-28TS(config)#dot1x timeout supp-timeout 5 44.10 dot1x max- req Description The dot1x max-req command is used to configure the maximum transfer times of the repeated authentication request when the server cannot be connected. To restore to the default value, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 415
for the Gigabit Ethernet port 1: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#dot1x 44.12 dot1x port-control Description The dot1x port-control command is used to configure the Control Mode of IEEE 802.1x for the specified port. By default, the control mode is "auto - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 416
"authorized-force": T2600G-28TS(config)#interface gigabitEthernet 1/0/20 T2600G-28TS(config-if)#dot1x port-control authorized-force 44.13 dot1x port-method Description The dot1x port-method command is used to configure the control type of IEEE 802.1x for the specified port. By default, the control - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 417
. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement None. Example Initialize the client whose MAC address is a 00:02:58:4f:6c:23 on port 1: T2600G-28TS(Config)# interface gigabitEthernet 1/0/1 T2600G-28TS(Config-if)#dot1x - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 418
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement None. Example Reauthenticate the client whose MAC address is a 00:02:58:4f:6c:23 on port 1: T2600G-28TS(Config)# interface gigabitEthernet 1/0/1 T2600G-28TS(Config-if)#dot1x - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 419
Privilege Requirement None. Example Display the configuration information of 801.X for Gigabit Ethernet port 20: T2600G-28TS(config)#show dot1x interface gigabitEthernet 1/0/20 Display the configuration information of 801.X for all Ethernet ports: T2600G-28TS(config)#show dot1x interface 44.18 show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 420
Example Display the authentication status of each port: T2600G-28TS(config)#show dot1x auth-state 397 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 421
can be learned on port 1/0/1 as 30, enable exceed-max-leaned feature and configure the mode as permanent and the status as drop: T2600G-28TS (config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#mac address-table max-mac-count max-number 30 exceed-maxlearned enable mode permanent status - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 422
port | gigabitEthernet port | ten-gigabitEthernet port } Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the port security configuration on port 1/0/1 T2600G-28TS# show mac address-table max-mac-count interface gigabitEthernet 1/0/1 399 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 423
troubleshooting the network. 46.1 monitor session destination interface Description The monitor session destination interface command is used to configure the monitoring port. Each monitor session has only one monitoring port. To change and configure port 1/0/1 as the monitoring port: T2600G-28TS( - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 424
session 1 destination interface gigabitEthernet 1/0/2 Delete the monitor session 1: T2600G-28TS(config)# no monitor session 1 46.2 monitor session source Description The monitor session source command is used to configure the monitored interface. To delete the corresponding monitored interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 425
strictly. 4. The monitoring port and monitored ports cannot be link-aggregation member. Example Create monitor session 1, then configure port 4, 5, 7 as monitored port and enable ingress monitoring: T2600G-28TS(config)# monitor session 1 source interface gigabitEthernet 1/0/4-5,1/0/7 rx Delete port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 426
T2600G-28TS(config)# show monitor session 1 403 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 427
Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an IP ACL whose ID is 523: T2600G-28TS(config)# access-list create 523 47.2 access-list packet-content profile Note: T2600G-18TS does not support Packet - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 428
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure a packet content profile with offset 0,1,2,3: T2600-28TS(config)# access-list packet-content profile chunk-offset0 0 chunk-offset1 1 chunk-offset2 2 chunk-offset3 3 47.3 access - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 429
Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Resequence the rules of ACL 12 with the start ID as 1 and step value as 5: T2600G-28TS(config)# access-list resequence 12 1 step 5 47.4 access-list mac - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 430
-range. The default is No Limit. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create MAC ACL 50 and configure Rule 5 to permit packets with source MAC address 00:34:a2:d4:34:b5: T2600G-28TS (config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 431
will be generated if the matching times changes. sip-address -- Enter the source IP address. sip-address-mask -- Enter the mask of the source IP address. This is required if a source IP address is entered. dip-address -- Enter the destination IP address. dip-address-mask -- Enter the mask of the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 432
. The default is No Limit. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create IP ACL 600, and configure Rule 1 to permit packets with source IP address 192.168.1.100: T2600G-28TS (config)#access - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 433
default is No Limit. source-ip: Enter the source IP address. source-ip-mask -- Enter the mask of the source IP address. It is required if source IP address is entered. destination-ip -- This is required if a source IP address is entered. destination-ip-mask -- Enter the destination IP address mask - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 434
default is No Limit. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create Combined ACL 1100 and configure Rule 1 to deny packets with source IP address 192.168.3.100 in VLAN 2: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 435
the packets that match the rule. By default, it is set to permit. The changes. class-value -- Specify a class value to be matched. It ranges from 0 to 63. flow-label-value -- Specify a Flow Label value to be matched. source-ip-address -- Enter the source IP address. Enter the destination IPv6 address - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 436
the SDM template as "enterpriseV6" and save your configurations. Example Create IPv6 ACL 1600 and configure Rule 1 to deny packets with source IPv6 address CDCD:910A:2222:5498:8475:1111:3900:2020: T2600G-28TS(config)# access-list create 1600 T2600G-28TS(config)# access-list ipv6 1600 rule 1 deny - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 437
Counter trap enabled, a related trap will be generated if the matching times changes. value-- Specify the chunk value, ranging from 0-ffffffff. mask --Specify the ACL rule with all 4 chunks configured, the rule id is 1 and the default action is permit: T2600-28TS(config)# access-list packet-content - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 438
. Example Specify the rule 1 of ACL 200 to be configured with policies: T2600G-28TS(config)# access-list action 200 1 47.10 redirect Description The which the packets will be redirected. The default is All. Command Mode Action Configuration Mode Privilege Requirement Only Admin, Operator and Power - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 439
these commands. Example Configure a policy for rule 1 of ACL 6: limit the transmission rate of the matched packets as 1000 Kbps and if the number of bytes per second is beyond 100, the packets will be discarded by the switch: T2600G-28TS(config)#access-list action 6 rule 1 T2600G-28TS(config-action - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 440
matching this rule: T2600G-28TS(config)#access-list action 6 rule 1 T2600G-28TS(config-action)#s-mirror interface gigabitEthernet 1/0/2 47.13 qos-remark Description The qos-remark command is used to configure QoS Remark function of policy action. To restore the settings to the default, please use no - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 441
802.1P priority of QoS Remark. This remark configuration will change the data packet's 802.1P priority field to Configure a policy for rule 1 of ACL 6: specify the DSCP region as 30 and local priority 2 for the packets matching this rule: T2600G-28TS(config)#access-list action 6 rule 1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 442
The ID or name of the ACL selected to display the configuration. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the MAC ACL whose ID is 20: T2600G-28TS(config)# show access-list 20 47.16 show access-list bind Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 443
ACL entry resource. Syntax show access-list status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the usage status of ACL entry resource: T2600G-28TS(config)# show access-list status 47.18 show access-list counter Description The show access - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 444
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the packet counter of ACL 100: T2600G-28TS(config)# show access-list 100 counter 47.19 clear access-list Description The clear access-list command is used to clear the counter of matched - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 445
| ip-verify-source | both --The protect type for the entry. "arp-detection" indicates ARP detection; "ip-verify-source" indicates IP source filter; "none" indicates applying none; "both" indicates applying both. ip-addr -- The IP address of the entry to be deleted. Command Mode Global Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 446
for automatic binding. Syntax ip dhcp snooping no ip dhcp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Snooping function globally: T2600G-28TS(config)#ip dhcp snooping 423 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 447
6-7: T2600G-28TS(config)#ip dhcp snooping vlan 1,4,6-7 48.4 ip dhcp snooping max-entries Description The ip dhcp snooping max-entries command is used to configure the maximum number of entries that can be learned on a port via DHCP Snooping. To restore to the default setting, please use no ip dhcp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 448
to these commands. Example Configure the maximum number of entries that can be learned on port 1 as 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#ip dhcp snooping max-entries 100 48.5 show ip source binding Description The show ip source binding command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 449
None. Example Display the running status of DHCP Snooping: T2600G-28TS#show ip dhcp snooping 48.7 show ip dhcp snooping interface Description The show ip dhcp snooping interface command is used to display the DHCP Snooping configuration of a desired Gigabit Ethernet port/port channel or of - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 450
Example Display the DHCP Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ip dhcp snooping interface Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ip dhcp snooping interface gigabitEthernet 1/0/5 427 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 451
for the ARP Inspection and IP verify source to filter the packets. 49.1 Ipv6 source binding Description The ipv6 source binding command is used to bind the IPv6 address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IPv6 address, MAC address, VLAN ID and the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 452
the process of the Host obtaining the IP address from DHCPv6 server, and record the IPv6 address, MAC address, VLAN and the connected Port number of the Host for automatic binding. Syntax Ipv6 dhcp snooping no ipv6 dhcp snooping Command Mode Global Configuration Mode Privilege Requirement Only Admin - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 453
on VLAN 1, 4, 6-7: T2600G-28TS(config)#ipv6 dhcp snooping vlan 1,4,6-7 49.4 ipv6 dhcp snooping max-entries Description The ipv6 dhcp snooping max-entries command is used to configure the maximum number of entries that can be learned on a port via DHCPv6 Snooping. To restore to the default setting - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 454
, Operator and Power User level users have access to these commands. Example Configure the maximum number of entries that can be learned on port 1 as 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#ipv6 dhcp snooping max-entries 100 49.5 ipv6 nd snooping Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 455
function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the ND snooping function on VLAN 1,4,6-7: T2600G-28TS(config)#ipv6 nd snooping vlan 1,4,6-7 49.7 ipv6 nd - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 456
and Power User level users have access to these commands. Example Configure the maximum number of binding entries from ND Snooping of Gigabit Ethernet port 1/0/2 is 100: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ipv6 nd snooping max-entries 100 49.8 show ipv6 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 457
of DHCPv6 Snooping. Syntax show ipv6 dhcp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the running status of DHCPv6 Snooping: T2600G-28TS#show ipv6 dhcp snooping 49.10 show ipv6 dhcp snooping interface Description The show ipv6 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 458
Requirement None. Example Display the DHCPv6 Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ipv6 dhcp snooping interface Display the DHCPv6 Snooping configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ipv6 dhcp snooping interface gigabitEthernet 1/0/5 49 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 459
Privilege Requirement None. Example Display the ND Snooping configuration of all Ethernet ports and port channels: T2600G-28TS#show ipv6 nd snooping interface Display the ND Snooping configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ipv6 nd snooping interface gigabitEthernet 1/0/5 436 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 460
is used to configure the IP Verify Source mode for a specified port. To disable the IP Verify Source function, please use no ip verify source command. Syntax For T2600G-18TS: ip verify source { sip | sip+mac } no ip verify source For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: ip verify source - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 461
for Gigabit Ethernet ports 5-10. Configure that only the packets with its source IP address, source MAC address and port number matched to the IP-MAC binding rules can be processed: T2600G-28TS(config)#interface range gigabitEthernet 1/0/5-10 T2600G-28TS(config-if-range)#ip verify source sip+mac 50 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 462
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IP Verify Source configuration information: T2600G-28TS(config)#show ip verify source 50.4 show ip verify source interface Description The show ip verify source interface command is used to - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 463
processed. sipv6+mac -- Only the packets with its source IPv6 address, source MAC address and port number matched to the IPv6-MAC binding rules can be processed. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Privilege Requirement Only Admin - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 464
address and port number matched to the IPv6-MAC binding rules can be processed: T2600G-28TS(config)#interface range gigabitEthernet 1/0/5-10 T2600G-28TS(config- Any Configuration Mode Privilege Requirement None. Example Display the IPv6 Verify Source configuration information: T2600G-28TS(config)# - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 465
Privilege Requirement None. Example Display the IPv6 verify source configuration of Gigabit Ethernet port 1/0/5: T2600G-28TS#show ipv6 verify source interface gigabitEthernet 1/0/5 442 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 466
filter command. Syntax ip dhcp filter no ip dhcp filter Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Filter function globally: T2600G-28TS(config)#ip dhcp filter 52.2 ip dhcp filter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 467
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface port-channel / interface range port-channel) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Filter on port 1/0/1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 468
T2600G-28TS(config-if)#ip dhcp filter mac-verify 52.4 ip dhcp filter limit rate Description The ip dhcp filter limit rate command is used to enable the Flow Control feature for the DHCP packets. The excessive DHCP packets will be discarded. To restore to the default configuration, please use no ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 469
have access to these commands. Example Configure the rate limit of DHCP Decline packets as 20 packets per second on Gigabit Ethernet port 1/0/2: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ip dhcp filter decline 20 52.6 ip dhcp filter server permit-entry Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 470
1/0/1 without client MAC address restricted: T2600G-28TS(config)#ip dhcp filter server permit-entry server-ip 192.168.0.100 client-mac all interface gigabitEthernet 1/0/1 52.7 show ip dhcp filter Description The show ip dhcp filter command is used to display the configuration of DHCP Filter. Syntax - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 471
None. Example Display the DHCP Filter configuration: T2600G-28TS#show ip dhcp filter 52.8 show ip dhcp filter interface Description The show ip dhcp filter interface command is used to display the configuration of DHCP Filter on ports. Syntax show ip dhcp filter interface [fastEthernet port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 472
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the legal DHCP server configuration: T2600G-28TS#show ip dhcp filter server permit-entry 449 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 473
are present on the network and both provide DHCPv6 services to different distinct groups of clients. 53.1 ipv6 dhcp Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCPv6 Filter function globally: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 474
1/0/1 T2600G-28TS(Config-if)#ipv6 dhcp filter 53.3 ipv6 dhcp filter limit rate Description The ipv6 dhcp filter limit rate command is used to enable the Flow Control feature for the DHCPv6 packets. The excessive DHCPv6 packets will be discarded. To restore to the default configuration, please - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 475
port 2 as 20 pps: T2600G-28TS(config)#interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ipv6 dhcp filter limit rate 20 53.4 ipv6 dhcp filter decline rate Description The ipv6 dhcp filter decline rate command is used to enable the Decline Protect feature and configure the rate limit on DHCP - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 476
. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create an entry for the legal DHCPv6 server whose IP address is 192.168.0.100 and connected port number is 1/0/1: T2600G-28TS(config)#ipv6 dhcp filter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 477
of DHCPv6 Filter. Syntax show ipv6 dhcp filter Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCPv6 Filter configuration: T2600G-28TS#show ipv6 dhcp filter 53.7 show ipv6 dhcp filter interface Description The show ipv6 dhcp filter - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 478
is used to display the legal server configuration. Syntax show ipv6 dhcp filter server permit-entry Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the legal DHCPv6 server configuration: T2600G-28TS#show ipv6 dhcp filter server permit-entry - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 479
sending a lot of service requests to the Host. Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DoS defend function globally: T2600G-28TS(config)#ip dos-prevent 54.2 ip dos-prevent type Description The ip - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 480
flood | syn-flood | win-nuke | ping-of-death | xma-scan } For T2600G-28TS/T2600G-28MPS/T2600G-28SQ/T2600G-52TS: ip dos-prevent type { land | scan-synfin | xma-scan | null-scan | both of the source IP address and the destination IP address of the SYN packet are set to be the IP address of the host, - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 481
default, respond to this by sending a reply to the source IP address. If the number of machines on the network that receive and respond to these packets is very large, the victim's computer will be flooded with traffic. Note: Only T2600G-18TS supports Smurf Attack. Command Mode Global Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 482
Syntax show ip dos-prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DoS information of the detected DoS attack globally: T2600G-28TS(config)#show ip dos-prevent 459 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 483
T2600G-18TS does not support IP as the IP address of the sFlow agent. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the sFlow agent with the IP address as 192.168.0.1: T2600G-28TS(config)#sflow address - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 484
agent address should be assigned to the sFlow agent embedded in the switch before you enable the sFlow function. Example Enable sFlow function globally: T2600G-28TS(config)#sflow enable 55.3 sflow collector collector-ID Description The sflow collector collector-ID command is used to configure the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 485
value ranges from 300 to 1400 and the default value is 300 bytes. timeout --Specify the T2600G-28TS(config)# sflow collector collector-ID 1 ip 192.168.0.100 T2600G-28TS(config)# sflow collector collector-ID 1 port 3000 55.4 sflow sampler Description The sflow sampler command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 486
default value is 128 bytes. Command Mode Interface Configuration Mode Configure Gigabit Ethernet port 1 as the sFlow sampler: specify the Collector-ID as 1, the ingress rate as 1024: T2600G-28TS(config)#interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)#sflow sampler collector-ID 1 T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 487
sFlow collector. Syntax show sflow collector Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of the sFlow collector: T2600G-28TS#show sflow collector 55.7 show sflow sampler Description The show sflow sampler command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 488
monitoring and troubleshooting Ethernet networks. T2600G-28TS(config)# interface gigabitEthernet 1/0/2 T2600G-28TS(config-if)#ethernet-oam 56.2 ethernet-oam mode Description The ethernet-oam mode command is used to configure the OAM mode for the desired port. To return to the default configurations - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 489
1/0/2 T2600G-28TS(config-if)#ethernet-oam mode passive 56.3 ethernet-oam link-monitor symbol-period Description The ethernet-oam link-monitor symbol-period command is used to configure the parameters about one of the link events, error symbol period event. To return to the default configurations - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 490
1/0/2 T2600G-28TS(config-if)# ethernet-oam link-monitor symbol-period threshold 5 window 30 56.4 ethernet-oam link-monitor frame Description The ethernet-oam link-monitor frame command is used to configure the parameters about one of the link events, error frame event. To return to the default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 491
return to the default configuration. Command Mode Interface Configuration Mode (interface configure the error threshold as 6 and the event detection interval as 9 seconds on Gigabit Ethernet port 1/0/3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# ethernet-oam link - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 492
return to the default configuration. Command Mode Interface Configuration Mode (interface configure the error threshold as 6 and the event detection interval as 150000 frames on Gigabit Ethernet port 1/0/4: T2600G-28TS(config)# interface gigabitEthernet 1/0/4 T2600G-28TS(config-if)# ethernet-oam link - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 493
commands. Example For error frame seconds event, configure the error threshold as 8 and the event detection interval as 30 seconds on Gigabit Ethernet port 5: T2600G-28TS(config)# interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)# ethernet-oam link-monitor frame-seconds threshold 8 window 300 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 494
Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable the Dying Gasp link event notification on Gigabit Ethernet port 1/0/7: T2600G-28TS the default configurations, - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 495
Example Configure the client to process the received remote loopback request on Gigabit Ethernet port 1: T2600G-28TS(config)# interface gigabitEthernet 1/0/1 T2600G-28TS(config-if)# ethernet-oam remote-loopback received -remote-loopback process 56.9 ethernet-oam remote-loopback Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 496
number. By default, the Ethernet OAM statistics of all ports are cleared. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Clear Ethernet OAM statistics of Gigabit Ethernet port 1/0/3: T2600G-28TS(config)# clear - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 497
log of Gigabit Ethernet port 1/0/3: T2600G-28TS(config)# clear ethernet-oam event-log interface gigabitEthernet 1/0/3 56.12 show ethernet-oam configuration Description The show ethernet-oam configuration command is used to display Ethernet OAM configuration information. Syntax show ethernet-oam - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 498
By default, the Ethernet OAM event logs of all ports are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display Ethernet OAM event log of Gigabit Ethernet port 1/0/2: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 499
By default, the Ethernet OAM status of all ports is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Display Ethernet OAM status of Gigabit Ethernet port 1/0/2: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 500
link is detected, the corresponding port will be shut down automatically or manually (depending on the shut mode configured). Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable the DLDP function globally: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 501
. The operation to shut down the unidirectional link ports is accomplished by the users. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the shut-mode as manual: T2600G-28TS(config)# dldp shut-mode - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 502
to reset all the unidirectional links and restart the link detect process. Syntax dldp reset Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Reset the DLDP function globally: T2600G-28TS(config)# dldp reset 57 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 503
1/0/2-4: T2600G-28TS (config)# interface range gigabitEthernet 1/0/2-4 T2600G-28TS (config-if-range)# dldp 57.6 dldp reset (interface) Description The dldp reset command is used to reset the specified port and restart the link detect process. Syntax dldp reset Command Mode Interface Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 504
None. Example Display the global configuration of DLDP function: T2600G-28TS# show dldp 57.8 show dldp interface Description The show dldp interface command is used to display the configuration and state of the specified Ethernet port. By default, the configuration and state of all the ports - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 505
. To return to the default configuration, please use no snmp-server command. Syntax snmp-server no snmp-server Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the SNMP function: T2600G-28TS(config)# snmp-server 58 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 506
Only Admin level users have access to these commands. Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station: T2600G-28TS(config)# snmp-server view view1 1.3.6.1.6.3.20 include 58.3 snmp-server group Description The snmp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 507
only and changes can be configure the name as group 1, the Security Model as SNMP v3, the security level as authNoPriv, the management access to the assigned View viewDefault as read-write, besides the notification messages sent by View viewDefault can be received by Management station: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 508
user is connected to a remote SNMP engine. As the remote engine ID and user password are used to compute the authentication and privacy digests, before configuring a remote user, you need to set the remote engine ID first. group-name -- The Group Name of the User. The User is classified to the - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 509
admin to Group group2, and configure the Security Model of the user as v3, the Security Level of the group as authPriv, the Authentication Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: T2600G-28TS(config)# snmp-server user - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 510
community to access. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Add community public, and the community has read-write management right to View viewDefault: T2600G-28TS(config)# snmp-server community public read-write - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 511
algorithm and a privacy algorithm are applied to check and encrypt packets). By default, the option is "noAuthNoPriv". type -- The type of the notifications, access to these commands. Example Add a Notification entry, and configure the IP address of the management Host as 192.168.0.146, the UDP port - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 512
T2600G-28TS(config)# snmp-server host 192.168.0.146 162 admin smode v2c type inform retries 100 timeout 1000 Add a Notification entry, and configure the IP Address of the management Host as fe80::1234, the UDP port as 162, the User name of the management station as admin, the Security Model of - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 513
abcdef123456: T2600G-28TS(config SNMP standard traps are enabled by default. To disable the sending of changes from linkup to linkdown, and can be triggered when you disconnect a device to a port. warmstart -- Indicates the SNMP feature on the switch is reinitialized with the physical configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 514
is 80% by default. flash --Triggered when flash is modified during operations such as backup, reset, firmware upgrade, configuration import, and so on. lldp remtableschange --An lldp RemTablesChange notification is sent when the value of lldp StatsRemTableLastChangeTime changes. It can be utilized - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 515
is disabled by default. The system will generate the trap when the memory utilization exceeds 80%. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP extended bandwidth-control trap for the switch: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 516
to disable all the types of DDM traps. For more instructions about the alarm threshold or warning threshold, refer to Chapter 11 DDM Commands. Command Mode Global Configuration Mode Example Enable all the SNMP DDM traps for the switch: T2600G-28TS(config)# snmp-server traps ddm 58.11 snmp-server - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 517
when certain VLANs are deleted successfully. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable all SNMP extended VLAN-related traps for the switch: T2600G-28TS(config)# snmp-server traps vlan Enable VLAN-created trap - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 518
Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the ACL trap for the switch: T2600G-28TS(config)# snmp-server traps acl 58.14 snmp-server traps ip Description The snmp-server traps ip command is used to enable IP traps. To - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 519
Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the IP-Change trap for the switch: T2600G-28TS(config)# snmp-server traps ip change 58.15 snmp-server traps power Note: Only T2600G-28MPS supports this command. Description - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 520
port. To disable the sending of SNMP link status trap, please use no snmp-server traps link-status command. By default, it is disabled. Syntax snmp-server traps link-status no snmp-server traps link-status Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 521
status trap for port 3: T2600G-28TS(config)# interface gigabitEthernet 1/0/3 T2600G-28TS(config-if)# snmp-server traps link-status 58.17 rmon history Description The rmon history command is used to configure the history sample entry. To return to the default configuration, please use no rmon history - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 522
as 100 seconds for the entry 1-3: T2600G-28TS(config)# rmon history 1-3 interface gigabitEthernet 1/0/2 interval 100 owner owner1 58.18 rmon event Description The rmon event command is used to configure the entries of SNMP-RMON Event. To return to the default configuration, please use no rmon event - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 523
owner of the event as owner1: T2600G-28TS(config)# rmon event 1-4 user user1 Description Description1 type log owner owner1 58.19 rmon alarm Description The rmon alarm command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no rmon alarm command - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 524
. By default, it is 1800. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds: T2600G-28TS(config)#rmon - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 525
name -- The creator of the event entry, ranging from 1 to 16 characters. By default, it is "monitor". status -- The status of the statistics entry, either "underCreation Configure the statistics entries 1-3 with the statistics port as 1/0/1, owner as owner1 and status as valid: T2600G-28TS(config - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 526
View table. Syntax show snmp-server view Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the View table: T2600G-28TS# show snmp-server view 58.23 show snmp-server group Description The show snmp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 527
User table. Syntax show snmp-server user Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the User table: T2600G-28TS# show snmp-server user 58.25 show snmp-server community Description The show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 528
the SNMP. Syntax show snmp-server engineID Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the engineID: T2600G-28TS# show snmp-server engineID 58.28 show rmon history Description The show rmon - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 529
command. By default, the configuration of all SNMP-RMON enabled entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the Event configuration of entry1-4: T2600G-28TS# show rmon - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 530
By default, the configuration of all Alarm Management entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the Alarm Management entry 1-2: T2600G-28TS# show - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 531
Example Display the configuration of the statistics entry 1: T2600G-28TS#show rmon statistics 1 508 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 532
the PoE switch can supply, ranging from 1 to 384w. By default, the value is 384. Command Mode Global Configuration Mode Privilege Requirement None. Example Configure the max power the PoE switch can supply as 160w: T2600G-28MPS(config)# power inline consumption 160 59.2 power profile Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 533
limit, the PD linked to the port with lower priority will be disconnected. By default, the PoE T2600G-28MPS(config)# power profile "IP Camera" supply enable priority low consumption 50 59.3 power inline consumption (interface) Description The power inline consumption command is used to configure - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 534
" indicates you can manually enter a value ranging from 1 to 300. The value is in the unit of 0.1 watt. For instance, if you want to configure the max power as linked to the port with lower priority will be disconnected. By default, the priority level is "low". Command Mode Interface Configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 535
T2600G-28MPS(config-if)# power inline priority low 59.5 power inline supply Description The power inline supply command is used to configure the PoE status of the corresponding port. Syntax power inline supply { enable | disable } Parameter enable | disable -- The PoE status of the port. By default - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 536
double quotes. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement None. Example Bind the PoE profile named "IP Camera" to port 2: T2600G-28MPS(config)# interface gigabitEthernet 1/0/2 T2600G-28MPS(config-if)# power inline - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 537
Requirement None. Example Display the PoE information of the system: T2600G-28MPS# show power inline 59.9 show power inline configuration interface Description The show power inline configuration interface command is used to display the PoE configuration of the certain port. Syntax show power inline - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 538
port ] Parameter port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the PoE information of all ports: T2600G-28MPS# show power inline information interface 59.11 show power profile Description The show power - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 539
Example Display the defined PoE profile: T2600G-28MPS# show power profile 516 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 540
detection command. Syntax ip arp inspection no ip arp inspection Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the ARP Detection function globally: T2600G-28TS(config)#ip arp inspection 60 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 541
Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the switch to check whether the source MAC address and the sender MAC address are the same when receiving an ARP packet. T2600G-28TS(config)#ip arp - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 542
the ARP Detection function on VLAN 2 and enable the log feature on VLAN 2: T2600G-28TS(config)#ip arp inspection vlan 2 logging 60.4 ip arp inspection trust Description The ip arp inspection trust command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 543
5: T2600G-28TS(config)#interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)#ip arp inspection limit-rate 50 60.6 ip arp inspection burst-interval Description The ip arp inspection burst-interval command is used to configure the burst interval of a specified port. To restore to the default speed - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 544
access to these commands. Example Configure the burst interval as 2 seconds for Gigabit Ethernet port 5: T2600G-28TS(config)#interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)#ip arp inspection burst-interval 2 60.7 ip arp inspection recover Description The ip arp inspection recover command is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 545
to the ARP transmit status: T2600G-28TS(config)#interface gigabitEthernet 1/0/5 T2600G-28TS(config-if)#ip arp inspection recover 60.8 show ip arp inspection Description The show ip arp inspection command is used to display the ARP detection global configuration including the enable/disable status - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 546
None. Example Display the configuration of Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#show ip arp inspection interface gigabitEthernet 1/0/1 Display the configuration of all Ethernet ports: T2600G-28TS(config)#show ip arp inspection interface 60.10 show ip arp inspection vlan Description The - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 547
Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the number of the illegal ARP packets received: T2600G-28TS(config)#show ip arp inspection statistics 60.12 clear ip arp inspection statistics Description The clear ip arp inspection statistics command is - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 548
, please use no ipv6 nd detection command. Syntax ipv6 nd detection no ipv6 nd detection Command Mode Global Configuration Mode Example Enable the ND Detection function globally: T2600G-28TS(config)#ipv6 nd detection 61.2 ipv6 nd detection vlan Description The ipv6 nd detection vlan command is used - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 549
Global Configuration Mode Example Enable the Log function on VLAN 1,4,6-7: T2600G-28TS(config configure the port for which the ND Detection function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no ipv6 nd detection trust command .The specific port, such as up-linked - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 550
including the enable/disable status. Syntax show ipv6 nd detection Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ND Detection configuration globally: T2600G-28TS(config)#show ipv6 nd detection 61.6 show ipv6 nd detection interface Description The show ipv6 nd - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 551
Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Gigabit Ethernet port 1/0/1: T2600G-28TS(config)#show ipv6 nd detection interface gigabitEthernet 1/0/1 Display the configuration of all Ethernet ports: T2600G-28TS(config)#show ipv6 nd detection interface - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 552
ipv6 nd detection vlan command is used to display the VLAN configuration of ND Detection. Syntax show ipv6 nd detection vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ipv6 ND Detection configuration of VLAN. T2600G-28TS(config)#show ipv6 nd detection vlan 529 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 553
Enable the system log buffer: T2600G-28TS(config)#logging buffer 62.2 logging buffer level Description The logging buffer level command is used to configure the severity level and the status of the configuration input to the log buffer. To return to the default configuration, please use no logging - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 554
. By default, it is 6 indicating that the log information with level 0-6 will be saved in the log buffer. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Set the severity level as 5: T2600G-28TS(config)#logging - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 555
flash, ranging from 1 to 48 hours. By default, the synchronization process takes place every 24 hours. immediate Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify the log file synchronization frequency as 10 hours: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 556
value will be stored to the flash. To restore to the default level, please use no logging file flash level command. Syntax T2600G-28TS(config)#logging file flash level 7 62.6 logging host index Description The logging host index command is used to configure the Log Host. To clear the configuration - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 557
of the log host. The switch supports 4 log hosts at most. host-ip -- The IP for the log host. level Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Enable log host 2 and set its IP address as 192.168.0.148, the level 5: T2600G-28TS - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 558
be output to the terminal devices. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Output the log information with severity levels between 0-7 to the console port: T2600G-28TS(config)# logging console level 7 535 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 559
. This function is enabled by default. Syntax logging monitor no logging monitor Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Disable logging to the terminal devices: T2600G-28TS(config)# no logging monitor 62 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 560
: buffer and flash. Clear the information of the two channels, by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Clear the information in the log file: T2600G-28TS(config)# clear logging buffer 537 - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 561
the log file. Syntax show logging local-config Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the Local Log: T2600G-28TS(config)# show logging local-config 62.13 show logging loghost Description The show logging loghost - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 562
. Display all the log information in the log buffer by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the log information from level 0 to level 5 in the log buffer: T2600G-28TS(config)# show logging buffer level 5 62.15 show logging - TP-Link T2600G-52TS | T2600G Series Switches CLI Reference Guide Guide - Page 563
level will display. Display all the log information in the log file by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the log information with the level marked 0-3 in the log file: T2600G-28TS(config)# show logging flash level 3 540
CLI Reference Guide
T2600G-18TS /T2600G-28TS (TL-SG3424) /T2600G-28TS-DC/
T2600G-28MPS (TL-SG3424P) / T2600G-28SQ/ T2600G-52TS (TL-SG3452)
1910012658 REV4.2.0
December 2019