TP-Link T3700G-52TQ T3700G-52TQUN V1 CLI Reference Guide Guide
TP-Link T3700G-52TQ Manual
View all TP-Link T3700G-52TQ manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T3700G-52TQ manual content summary:
- TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 1
CLI Reference Guide JetStream 52-Port Gigabit Stackable L3 Managed Switch T3700G-52TQ REV1.0.0 1910011777 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 2
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 3
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide CONTENTS Preface ...1 Chapter 1 Using the CLI ...5 1.1 Accessing the CLI Format...15 Chapter 2 User Interface ...16 2.1 enable ...16 2.2 service password-encryption 16 2.3 enable password...17 2.4 enable secret ...18 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 4
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 3.11 3.12 show auto-copy-sw ...28 clear switch-synchronization...28 Chapter 4 IEEE 802.1Q VLAN Commands 30 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 vlan ...30 interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 5
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 8.6 show voice vlan oui-table...49 8.7 show voice vlan interface ...50 Chapter 9 Private VLAN Commands 51 9.1 private-vlan primary...51 9.2 private-vlan community...51 9.3 private- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 6
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 12.8 12.9 12.10 12.11 12.12 12.13 password ...73 login local...74 telnet ...74 show user account-list...75 show user configuration... - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 7
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 16.3 show ip verify source interface 95 Chapter 17 IEEE 802.1X Commands 96 17.1 17.2 17.3 17.4 17.5 17.6 17.7 17.8 17.9 17.10 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 8
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 19.5 19.6 19.7 19.8 ip ssh max-client ...117 ip ssh System Configuration Commands 138 22.1 22.2 22.3 22.4 system-time manual ...138 system-time ntp ...138 system-time dst predefined 140 system-time dst date ...141 VII - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 9
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.5 22.6 22.7 22.8 22.9 22.10 22.11 22.12 22.13 22.14 22.15 22.16 22.17 22.18 22.19 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 10
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 23.2 23.3 23.4 23.5 23.6 23.7 23.8 map 181 show classofservice queue mode 181 show classofservice queue trust 182 Chapter 25 Differentiated Services Commands 183 25.1 25.2 25.3 25.4 25.5 25.6 25.7 diffserv...183 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 11
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.8 25.9 25.10 25.11 25. single-rate ...204 two-rate...205 service-policy ...207 service-policy (interface) ...207 show diffserv ...208 show diffserv service brief ...208 show diffserv service ...209 show class-map ...209 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 12
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.46 show policy-map interface ...210 25.47 show policy-map interface lag 211 Chapter 26 Port Mirror Commands 212 26.1 26.2 26.3 monitor - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 13
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 30.1 30.2 30.3 30.4 30.5 30.6 30.7 30.8 30.9 30.10 30.11 30.12 30.13 30.14 30.15 30.16 30.17 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 14
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 31.11 31.12 31.13 31.14 31.15 31.16 31.17 31.18 31.19 31.20 31.21 31.22 31. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 15
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.22 32.23 32.24 32.25 32.26 32.27 32.28 show ipv6 mld snooping interface 277 show ipv6 mld snooping vlan - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 16
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.13 35.14 35.15 35.16 35.17 35.18 35.19 35.20 35 .21 35.22 35.23 35.24 35.25 35.26 35.27 35.28 35.29 snmp-server traps ospf state-change 301 snmp-server traps link - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 17
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 37.4 37.5 37.6 37.7 37.8 37.9 37.10 37.11 37.12 37.13 16 38.17 38.18 38.19 38.20 38.21 38.22 38.23 38.24 38.25 service dhcp server ...328 option code...328 extend-option capwap-ac-ip 329 extend-option vendor-class-id 329 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 18
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 38.26 38.27 38.28 38.29 binding 344 Chapter 39 DHCP Relay ...345 39.1 39.2 39.3 39.4 39.5 39.6 39.7 service dhcp relay ...345 ip helper-address...345 ip dhcp relay information ...346 ip dhcp relay information policy - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 19
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 41.18 41.19 41.20 41.21 41.22 41.23 show ip igmp profile...362 show ip igmp groups ...362 show ip igmp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 20
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 44.5 44.6 44.7 44.8 44.9 44.10 44.11 44.12 ip vrrp vrid priority ...383 ip vrrp vrid timer-advertise ...384 ip vrrp vrid - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 21
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.14 46.15 46.16 46.17 46 ospf database ...425 show ip ospf interface...426 show ip ospf neighbor...426 show ip ospf virtual-links...427 show ip ospf border-routers 427 show ip route ospf ...428 show ip ospf area database - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 22
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 48.1 48.2 48.3 48.4 48.5 48.6 48.7 48.8 48.9 48. 50.4 50.5 50.6 ipv6 enable...453 ipv6 address autoconfig...453 ipv6 address link-local ...454 ipv6 address dhcp ...455 ipv6 address ra ...455 ipv6 address eui-64 ...456 XXI - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 23
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 50.7 50.8 ipv6 address ...457 show ipv6 interface...457 Chapter 51 Management Port Commands 459 51.1 51.2 51.3 51.4 51.5 51.6 51.7 51.8 51.9 management- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 24
). The device mentioned in this Guide stands for T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch. Overview of this Guide Chapter 1: Using the CLI Provide information about the commands used for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation Control Protocol). 1 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 25
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 12: User Manage Commands Provide information about the commands Storm Control for ethernet ports. Chapter 24: Class of Service Commands Provide information about the commands used for configuring the CoS function. 2 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 26
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 25: Differentiated Services Commands Provide information about the commands used for configuring the Differentiated Services (DiffServ) function. Chapter 26: Port Mirror Commands Provide information about the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 27
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chatper 38: DHCP Server Commands Provide information about the commands used for configuring the DHCP Server function. Chapter 39: DCHP Relay Commands Provide information about - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 28
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 1 Using the CLI 1.1 on the resource CD. Follow the InstallSheild Wizard to accomplish the installation. The TP-Link USB Console Driver supports the following Windows operating systems: 32-bit Windows XP SP3 64 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 29
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 64-bit Windows 8 32-bit Windows 8.1 64-bit Windows 8.1 After the TP-Link USB Console Driver is installed, the PC's USB port will act as RS-232 serial port when the PC's USB port is connected to the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 30
52-Port Gigabit Stackable L3 Managed Switch CLI Guide 5. The DOS prompt "T3700G-52TQ>" will appear after pressing the Enter button as shown in Figure 1-2. It indicates that you can use the CLI now. Figure 1-2 Log in the Switch 1.1.2 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 31
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 1.1.3 Logon by Telnet By default, you can logon by Telnet in login local mode directly. 1. Make sure the switch and the PC are in the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 32
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 4. Type enable command to enter Privileged EXEC Mode. A password that you have set through Console port connection is required. Here the password has been set - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 33
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Password Authentication Mode 1. Open the software to log in to the interface of PuTTY. Enter the IP address of the switch into Host Name field; - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 34
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Configuration Mode, Router Configuration Mode, DHCP Configuration Mode, MST Configuration Mode and Class-Map Configuration Mode. Interface Configuration Mode can also be divided into Interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 35
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Mode Accessing Path Prompt Logout or Access the next mode VLAN Use the vlan vlan-list Configuration command to enter this mode from Global Configuration Mode mode. T3700G-52TQ(config- vlan)# Use the end command or press Ctrl - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 36
Guide Mode Accessing Path Prompt MST Use the spanning-tree mst Configuration configuration command to enter this mode from Global Mode Configuration mode. T3700G-52TQ link-aggregation: Configure parameters for a link-aggregation, such as broadcast storm. d). Interface range link-aggregation - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 37
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Router Configuration Mode: In this mode, Privileged EXEC mode. 1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: Items in square brackets [ ] are optional Items in braces { } - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 38
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 1.4.2 Special Characters You should pay attentions to the description below if the variable is a character string: These six characters cannot be input. If a blank is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 39
EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode: T3700G-52TQ>enable Password: T3700G-52TQ# 2.2 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 40
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the global encryption function: T3700G-52TQ(config)# service password-encryption 2.3 enable password Description The enable password command is used to set or change the password for users to access Privileged EXEC Mode - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 41
L3 Managed Switch CLI Guide 2. If both the enable password and enable secret password are defined, only the latest configured password will take effect. Example Set the super password as "admin" and unencrypted to access Privileged EXEC Mode from User EXEC Mode: T3700G-52TQ(config)#enable password - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 42
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide User Guidelines If both the enable password EXEC Mode Example Access Global Configuration Mode from Privileged EXEC Mode: T3700G-52TQ#configure T3700G-52TQ(config)# 2.6 exit Description The exit command is used to return - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 43
Stackable L3 Managed Switch CLI Guide Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: T3700G-52TQ(config-if)#exit T3700G-52TQ(config)#exit T3700G-52TQ# 2.7 end Description The end command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 44
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Show the commands you have entered in the current mode: T3700G-52TQ(config)# show history 1 show history 2.9 clear history Description The clear history command is used to clear the commands you have entered in the current mode - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 45
CLI Guide Chapter 3 Stack The stack technology is to connect multiple stackable devices through their stack ports, forming a stack which works as a unified system and presents as a single entity to the network in Layer 2 and Layer 3 protocols. This chapter describes how to manage the T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 46
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable downgrade of image on stack member: T3700G-52TQ(config)# boot auto-copy-sw allow-downgrade 3.3 boot auto-copy-sw trap Description The boot auto-copy-sw trap command is used to enable - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 47
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Specify the unit 1's role as master in the stack: T3700G-52TQ(config)# switch 1 master 3.5 switch standby Description The switch standby command is used to set the role of a specified switch - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 48
CLI Guide Syntax swtich unitid priority priority no switch unitid priority Parameter unitid -- Specify the member number. priority -- Specify the member's priority, ranging from 0 to 15. Command Mode Global Configuration Mode Example Specify the unit 1's priority as 10 in the stack: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 49
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 3.8 switch stack-port Description The switch stack which is not currently the stack member. The information of the provisioned member is manually created, or created/updated by the switch member when it joins the stack. The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 50
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax swtich unitid provision type no switch unitid provision Parameter unitid -- The stack member number of the provisioned switch. type -- The device type of the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 51
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and any Configuration Mode Example Display the detailed information of the current stack: T3700G-52TQ(config)# show switch detail 3.11 show auto-copy-sw Description The show auto-copy-sw command is used - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 52
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Clear the stack firmware synchronization information: T3700G-52TQ(config)# clear switch-synchronization 29 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 53
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 4 IEEE 802.1Q VLAN Commands VLAN (Virtual Local Area Network) technology is developed for the switch to divide the LAN into multiple logical LANs - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 54
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 4.2 interface vlan Description The from 1 to 4093. Command Mode Global Configuration Mode Example Create VLAN Interface 2: T3700G-52TQ(config)#interface vlan 2 4.3 name Description The name command is used to assign a - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 55
Port Gigabit Stackable L3 Managed Switch CLI Guide Example Specify the description string of the VLAN 2 as "VLAN002": T3700G-52TQ(config)#vlan 2 T3700G-52TQ(config-vlan)#name VLAN002 4.4 switchport mode Description The switchport mode command is used to configure the Link Types for the ports. Syntax - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 56
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no switchport access vlan Parameter vlan-id -- Specify IEEE 802. Gigabit Ethernet port 1/0/3 whose link type is "access" to VLAN 2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)#switchport access - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 57
CLI Guide T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#switchport mode trunk T3700G-52TQ( link type is "general" to VLAN 2 and its egress-rule as "tagged": T3700G-52TQ(config)#interface gigabitEthernet 1/0/4 T3700G-52TQ(config-if)#switchport mode general T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 58
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 4.8 switchport pvid Description The switchport pvid of Gigabit Ethernet port 1/0/3 (General) as 1: T3700G-52TQ(config)#interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)#switchport pvid 1 4.9 switchport trunk native - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 59
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode ( Mode Example Display the detailed information of Gigabit Ethernet port 1/0/3: T3700G-52TQ(config)#show interface switchport gigabitEthernet 1/0/3 4.11 show vlan summary Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 60
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show vlan summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the summarized information of IEEE 802.1Q VLAN: T3700G-52TQ(config)#show vlan summary 4.12 show vlan brief Description The show vlan - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 61
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter vlan-id -- Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4093. Using Mode Privileged EXEC Mode and Any Configuration Mode Example Display the detailed information of VLAN 2: T3700G-52TQ(config)#show vlan id 2 38 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 62
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 5 MAC-based VLAN Commands MAC VLAN Global Configuration Mode Example Create VLAN 2 with the MAC address 00:11:11:01:01:12 : T3700G-52TQ(config)#mac-vlan mac-address 00:11:11:01:01:12 vlan 2 5.2 show mac-vlan - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 63
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show mac-vlan { all | mac-address mac-addr | vlan vlan-id } Command Mode Privileged ID, ranging from 1 to 4093. Example Display the information of all the MAC-based VLAN entry: T3700G-52TQ(config)#show mac-vlan all 40 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 64
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 6 Protocol VLAN Commands Protocol-based VLAN (Virtual Local Area Network) " whose ID is 1 and Ethernet protocol type is 0x0800: T3700G-52TQ(config)#protocol-vlan template 1 name Temp1 frame ether_2 ether-type 0800 41 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 65
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 6.2 protocol-vlan vlan Description The protocol-vlan Protocol-based VLAN 2 and bind it with Protocol-based VLAN Template 3: T3700G-52TQ(config)# protocol-vlan vlan 2 template 3 6.3 protocol-vlan Description The protocol - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 66
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet/ interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Parameter index -- Specify the protocol group ID. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 67
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display information of the Protocol-based VLAN entry: T3700G-52TQ(config)# show protocol-vlan vlan 44 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 68
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide access terminal of the Internet Service Provider. And these packets link port. To close this VPN up-link port, please use the no switchport dot1q-tunnel mode command. By default, no port has been configured as the VPN up-link - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 69
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax switchport dot1q-tunnel mode nni no switchport dot1q- Gigabit Ethernet port 1/0/3 as the VPN up-link port: T3700G-52TQ(config)#interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)#switchport dot1q-tunnel mode nni 7.3 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 70
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 8 Voice VLAN Commands . Command Mode Global Configuration Mode Example Enable the Voice VLAN function for VLAN 10: T3700G-52TQ(config)#voice vlan 10 8.2 voice vlan (interface) Description The voice vlan command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 71
Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Enable the Voice VLAN mode for the Gigabit Ethernet port 1/0/3: T3700G-52TQ(config)#interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 72
CLI Guide Syntax voice vlan oui oui-prefix no voice vlan oui oui-prefix Parameter oui-prefix -- The OUI address prefix of the voice device, in the format of XX:XX:XX. Command Mode Global Configuration Mode Example Create a Voice VLAN OUI with the OUI address prefix 00:11:11: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 73
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show voice vlan oui-table Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN OUI-Table: T3700G-52TQ(config)#show voice vlan oui-table 8.7 show voice vlan interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 74
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 9 Private VLAN Commands Private VLANs are configured specially for saving VLAN resource of uplink devices and decreasing broadcast. 9.1 private-vlan primary Description The private- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 75
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode VLAN Configuration Mode (VLAN) Example Configure the VLAN 4 as the community VLAN of the private VLAN: T3700G-52TQ(config)#vlan 4 T3700G-52TQ(config-vlan)#private-vlan community 9.3 private-vlan isolated Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 76
Stackable L3 Managed Switch CLI Guide Parameter vlan_list -- Secondary VLAN ID, ranging from 2 to 4093. Command Mode VLAN Configuration Mode (VLAN) Example Associate primary VLAN 3 with community VLAN 4 as a private VLAN: T3700G-52TQ(config)#vlan 3 T3700G-52TQ(config-vlan)#private-vlan association - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 77
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 9.6 switchport private-vlan host-association Description The switchport private-vlan host-association command is used to add host type port to private VLAN. To remove - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 78
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter primary-vlan-id -- Primary VLAN ID, ranging from 2 to 4093. secondary-vlan-id -- Secondary VLAN ID, ranging from 2 to 4093. Command Mode Interface Configuration - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 79
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 9.9 show vlan private-vlan interface Description The show vlan private-vlan interface command is used to display the Private VLAN configuration information of the specified - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 80
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 10 GVRP Commands GVRP (GARP gvrp no gvrp Command Mode Global Configuration Mode Example Enable the GVRP function globally: T3700G-52TQ(config)#gvrp 10.2 gvrp (interface) Description The gvrp command is used to enable - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 81
Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Enable the GVRP function for Gigabit Ethernet ports 1/0/2-6: T3700G-52TQ(config)#interface range - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 82
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Set the GARP leaveall timer of Gigabit - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 83
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter port --The Gigabit/Ten-Gigabit Ethernet Display the GVRP configuration information of Gigabit Ethernet port 1: T3700G-52TQ(config)#show gvrp interface gigabitEthernet 1/0/1 Display the GVRP configuration - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 84
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 11 Etherchannel Commands Etherchannel Commands are used to configure LAG and LACP function. LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, which can - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 85
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#interface range gigabitEthernet 1/0/2-4 T3700G-52TQ(config-if-range)#channel-group 1 mode on 11.2 port-channel load-balance Description The port-channel load-balance command is used to configure the Aggregate - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 86
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 11.3 lacp system-priority Description Mode Global Configuration Mode Example Configure the LACP system priority as 1024 globally: T3700G-52TQ(config)#lacp system-priority 1024 11.4 lacp port-priority Description The lacp port - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 87
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet/ interface ten-gigabitEthernet / interface range ten- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 88
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 11.6 show etherchannel load-balance Description Mode and Any Configuration Mode Example Display the Aggregate Arithmetic of LAG: T3700G-52TQ(config)#show etherchannel load-balance 11.7 show lacp Description The show lacp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 89
Managed Switch CLI Guide 11.8 show lacp sys-id Description The show lacp sys-id command is used to display the LACP system priority globally. Syntax show lacp sys-id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LACP system priority: T3700G-52TQ(config)#show lacp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 90
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 12 User Manage Commands User Manage Commands are used to manage the user's logging information by Web, Telnet or SSH, so as to protect - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 91
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode User Guidelines 1. If the password you configured here is unencrypted and the global encryption function is enabled in service password-encryption, the password in the configuration - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 92
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide password --Users' login password, a string from the password is "admin". The password will be displayed in the encrypted form. T3700G-52TQ(config)#user name tplink privilege admin secret 0 admin 12.3 user access-control ip- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 93
Switch CLI Guide [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ] -- Specify the access interface. These interfaces are enabled by default. Command Mode Global Configuration Mode Example Enable the access-control of the user whose IP address is 192.168.0.148: T3700G-52TQ(config)# user - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 94
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 12.5 user access-control port-based Description Configure that only the users connected to ports 2-6 are allowed to login: T3700G-52TQ(config)# user access-control port-based interface gigabitEthernet 1/0/2-6 12.6 media-type - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 95
Switch CLI Guide console is enabled. To return to the default configuration, please use no media-type rj45 command. Syntax media-type rj45 no media-type rj45 Command Mode Line Configuration Mode Example Enable the RJ-45 console input: T3700G-52TQ(config)# line console 0 T3700G-52TQ(config-line - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 96
enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Configure the connection password of Console port connection 0 as "tplink" and unencrypted: T3700G-52TQ(config)#line console 0 T3700G-52TQ(config-line)#password - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 97
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Configure the connection password of virtual terminal connection 0-5 as "tplink" and unencrypted: T3700G-52TQ(config)#line vty 0 5 T3700G-52TQ(config-line)#password 0 tplink 12.9 login local Description The login local command is used - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 98
-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Disable the Telnet function: T3700G-52TQ (config)# telnet disable 12.11 show Any Configuration Mode Example Display the information of the current users: T3700G-52TQ(config)#show user account-list 12.12 show user configuration Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 99
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 12.13 show telnet-status Description The show telnet-status command is used to display EXEC Mode and Any Configuration Mode Example Display whether the Telnet function is enabled: T3700G-52TQ(config)# show telnet-status 76 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 100
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 13 Binding Table Commands You .168.0.1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 1/0/5 manually: T3700G-52TQ(config)#ip source binding 192.168.0.1 00:00:00:00:00:01 vlan 2 interface gigabitEthernet 1/0/5 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 101
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#no ip source binding 00:00:00 snooping Command Mode Global Configuration Mode Example Enable the DHCP Snooping function globally: T3700G-52TQ(config)#ip dhcp snooping 13.3 ip dhcp snooping vlan Description The ip dhcp snooping - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 102
Stackable L3 Managed Switch CLI Guide Parameter vlan-range -- Specify the VLANs to enable the DHCP snooping function, in the format of 1-3, 5. Command Mode Global Configuration Mode Example Enable the DHCP Snooping function on VLAN 1,4,6-7: T3700G-52TQ(config)#ip dhcp snooping vlan 1,4,6-7 13 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 103
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip dhcp snooping information strategy strategy no field of the packets with the switch defined one and then send out: T3700G-52TQ(config)#ip dhcp snooping information strategy replace 13.6 ip dhcp snooping information - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 104
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the customized sub-option Remote ID for the Option 82 as tplink: T3700G-52TQ(config)#ip dhcp snooping information remote-id tplink 13.7 ip dhcp snooping information circuit-id - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 105
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 13.8 ip dhcp snooping trust Description The ip dhcp Gigabit Ethernet port 1/0/2 to be a Trusted Port: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#ip dhcp snooping trust 13.9 ip dhcp snooping - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 106
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the MAC Verify feature: T3700G-52TQ(config)#ip dhcp snooping mac-verify 13.10 ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 107
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip source binding Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IP-MAC-VID-PORT binding table: T3700G-52TQ(config)#show ip source binding 13.12 show ip dhcp snooping Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 108
Stackable L3 Managed Switch CLI Guide Parameters port -- The Ethernet port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the DHCP Snooping configuration of all Ethernet ports and LAGs: T3700G-52TQ#show ip dhcp snooping interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 109
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 14 ARP Inspection Commands ARP (Address Enable the ARP Detection function for VLAN 5 and enable the logging feature: T3700G-52TQ(config)#ip arp inspection vlan 5 logging 14.2 ip arp inspection validate Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 110
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip arp inspection validate {src-mac|dst Port list, please use no ip arp detection trust command .The specific ports, such as up-linked port, routing port and LAG port, should be set as Trusted Port. To ensure the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 111
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Configure the Gigabit Ethernet ports 1/0/2-5 as the Trusted Port: T3700G-52TQ(config)#interface range gigabitEthernet 1/0/2-5 T3700G-52TQ(config-if-range)#ip arp inspection trust 14.4 ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 112
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 14.5 ip arp inspection recover Description The ip arp Gigabit Ethernet port 1/0/5 to the ARP transmit status: T3700G-52TQ(config)#interface gigabitEthernet 1/0/5 T3700G-52TQ(config-if)#ip arp inspection recover 14.6 show ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 113
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 14.7 show ip arp inspection interface Description The show ip arp inspection interface command is used to display the interface configuration of ARP detection. Syntax - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 114
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#show ip arp inspection statistics 14.9 clear ip arp inspection statistics Configuration Mode Example Clear the statistic of the illegal ARP packets received: T3700G-52TQ(config)#clear ip arp inspection statistics 91 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 115
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 15 DoS Defend Commands DoS (Denial of Service) Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host. With the DoS Defend - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 116
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the DoS Defend Type named Land attack: T3700G-52TQ(config)#ip dos-prevent type land 93 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 117
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 16 IP Verify Source Commands IP Verify Source is to filter the IP packets based on the IP-MAC Binding entries. Only the packets - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 118
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 16.2 show ip verify source Description The and Any Configuration Mode Example Display the IP Verify Source configuration information: T3700G-52TQ#show ip verify source 16.3 show ip verify source interface Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 119
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 17 IEEE 802.1X Commands IEEE control Command Mode Global Configuration Mode Example Enable the IEEE 802.1X function: T3700G-52TQ(config)#dot1x system-auth-control 17.2 dot1x timeout quiet-period Description The dot1x - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 120
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter time -- The length of the quiet-period time. If one user's authentication fails, its subsequent IEEE 802.1x authentication requests will not be processed - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 121
CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Configure the supplicant timeout value as 5 seconds for Gigabit Ethernet port 1/0/1: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 122
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 17.5 dot1x max-req Description The dot1x repeated authentication request as 5 on Gigabit Ethernet port 1/0/2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#dot1x max-req 5 17.6 dot1x Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 123
Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / interface range ten-gigabitEthernet) Example Enable the IEEE 802.1X function for the Gigabit Ethernet port 1/0/1: T3700G-52TQ(config)#interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 124
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 17.8 dot1x timeout guest-vlan-period Description The Guest VLAN Period as 100s on Gigabit Ethernet port 1/0/2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)# dot1x timeout guest-vlan-period 100 17 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 125
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter auto | authorized-force | unauthorized-force -- Gigabit Ethernet port 1/0/20 as "authorized-force": T3700G-52TQ(config)#interface gigabitEthernet 1/0/20 T3700G-52TQ(config-if)#dot1x port-control authorized-force 17 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 126
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide mac-based: Any client connected to the port should Type for Gigabit Ethernet port 1/0/20 as "port-based": T3700G-52TQ(config)#interface gigabitEthernet 1/0/20 T3700G-52TQ(config-if)#dot1x port-method port-based 17.11 dot1x - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 127
Switch CLI Guide 17.12 show dot1x global Description The show dot1x global command is used to display the global configuration of 802.1X. Syntax show dot1x global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of 802.1X globally: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 128
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 18 System Log Commands The buffer Command Mode Global Configuration Mode Example Enable the system log buffer: T3700G-52TQ(config)#logging buffer 18.2 logging buffer level Description The logging buffer level command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 129
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no logging buffer level Parameter log buffer. Command Mode Global Configuration Mode Example Set the severity level as 5: T3700G-52TQ(config)#logging buffer level 5 18.3 logging file flash Description The logging file flash - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 130
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 18.4 logging file flash level Save the log messages with their severities equal or higher than 7 to the flash : T3700G-52TQ(config)#logging file flash level 7 18.5 logging host Description The logging host command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 131
Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable logging to a host: T3700G-52TQ(config)#logging host 18.6 no logging host index idx Parameter idx --The index of the log host. The switch supports 8 log hosts. host-ip -- The IP for the log host. level --The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 132
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 18.7 logging console Description The logging Command Mode Global Configuration Mode Example Enable logging to the console port: T3700G-52TQ(config)# logging console 18.8 logging console level Description The logging console - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 133
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Output the log information with severity levels between 0-7 to the console port: T3700G-52TQ(config)# logging console level 7 18.9 logging monitor Description The logging monitor command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 134
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter level -- Severity level of the log Output the log information with severity levels between 0-7 to the terminal devices: T3700G-52TQ(config)# no logging monitor 18.11 clear logging Description The clear logging - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 135
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 18.12 show logging config Description The Mode and Any Configuration Mode Example Display the configuration of the Local Log: T3700G-52TQ(config)#show logging config 18.13 show logging loghost Description The show logging - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 136
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 18.14 show logging buffer Description Example Display the log information from level 0 to level 5 in the log buffer: T3700G-52TQ(config)#show logging buffer level 5 18.15 show logging flash Description The show logging flash - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 137
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Display the log information with the level marked 0-3 in the log file: T3700G-52TQ(config)#show logging flash level 3 114 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 138
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 19 SSH Commands SSH ( server no ip ssh server Command Mode Global Configuration Mode Example Enable the SSH function: T3700G-52TQ(config)# ip ssh server 19.2 ip ssh version Description The ip ssh version command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 139
L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable SSH v2: T3700G-52TQ(config)# ip ssh version Command Mode Global Configuration Mode Example Specify the SSH algorithm as AES128-CBC: T3700G-52TQ(config)# ip ssh algorithm AES128-CBC 19.4 ip ssh timeout Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 140
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter value -- The Idle-timeout time Mode Global Configuration Mode Example Specify the idle-timeout time of SSH as 30 seconds: T3700G-52TQ(config)# ip ssh timeout 30 19.5 ip ssh max-client Description The ip ssh max - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 141
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 19.6 ip ssh supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Example Download an SSH-1 type key file named ssh-key from TFTP server with the IP address 192.168.0.148: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 142
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide downloaded DSA/RSA key files. of SSH key to generate. Command Mode Global Configuration Mode Example Generate the DSA key: T3700G-52TQ(config)# crypto key generate dsa 19.8 show ip ssh Description The show ip ssh command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 143
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 20 HTTP and HTTPS Commands With the help of HTTP (HyperText Transfer Protocol) or no ip http server Command Mode Global Configuration Mode Example Disable the HTTP function: T3700G-52TQ(config)# no ip http server 120 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 144
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 20.2 ip http session maxsessions Description Configure the maximum number of the users logging on to the HTTP server as 3: T3700G-52TQ (config)# ip http session maxsessions 3 20.3 ip http session hard-timeout Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 145
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the hard-timeout of the HTTP connection as 30 hours: T3700G-52TQ(config)# ip http session hard-timeout 30 20.4 ip http session soft-timeout Description The ip http session soft - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 146
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip http secure-server no ip http secure-server Command Mode Global Configuration Mode Example Disable the HTTP function: T3700G-52TQ(config)# no ip http secure-server 20.6 ip http secure-protocol Description The ip http secure - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 147
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 20.7 ip http secure-ciphersuite Description The ip http secure-ciphersuite command is used to configure the cipherSuites over the SSL connection supported by the switch. To restore to the default ciphersuite types, please - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 148
Stackable L3 Managed Switch CLI Guide Parameter time --The hard-timeout time, ranging from 1 to 168 in hours. By default, the value is 24. Command Mode Global Configuration Mode Example Configure the hard-timeout of the HTTPS connection as 30 hours: T3700G-52TQ(config)# ip http secure-session - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 149
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide To cancel this limitation, please use no ip http secure-session The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode 126 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 150
the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Example Download an SSL key named ssl-key from TFTP server with the IP address of 192.168.0.146: T3700G-52TQ(config)# ip http secure-server download key ssl-key - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 151
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Download an SSL key named ssl-key from TFTP server with the IP address of fe80::1234 T3700G-52TQ(config)# ip http secure-server download key ssl-key ip-address fe80::1234 20.13 show ip http configuration Description The show ip http - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 152
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 21 MAC Address Commands MAC Address use no mac address-table static command. The static address can be added or removed manually, independent of the aging time. In the stable networks, the static MAC address entries - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 153
Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#no mac address-table static vid 1 Delete the static address entry whose MAC address is 00:02:58:4f:6c:23: T3700G-52TQ(config)#no mac address-table . The filtering address can be added or removed manually, independent of the aging time. 130 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 154
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax mac address-table filtering mac-addr vid vid no mac entry of which VLAN ID is 1 and MAC address is 00:1e:4b:04:01:5d: T3700G-52TQ(config)#mac address-table filtering 00:1e:4b:04:01:5d vid 1 21.4 mac address-table - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 155
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter num -- The maximum number of MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted. When permanent mode is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 156
L3 Managed Switch CLI Guide Parameter dynamic | static | filtering -- The type of your desired entry. By default all the entries are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all address entries: T3700G-52TQ(config)#show mac address - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 157
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter all -- Displays the security information of Mode Example Display the security configuration of Gigabit Ethernet port 1/0/20: T3700G-52TQ(config)#show mac address-table max-mac-count interface gigabitEthernet 1/0/20 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 158
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 21.9 show mac address-table count the total amount of MAC address table in VLAN 2 of all the units of the stack: T3700G-52TQ(config)#show mac address-table count vlan 2 21.10 show mac address-table address Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 159
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show mac address-table address mac-addr [ interface { fastEthernet the information of the MAC address 00:00:00:23:00:00 in VLAN 1: T3700G-52TQ(config)#show mac address-table address 00:00:00:23:00:00 vid 1 Display - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 160
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the MAC address configuration of vlan 1: T3700G-52TQ(config)#show mac address-table vlan 1 137 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 161
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 22 System Configuration Commands Configuration Mode Example Configure the system time as 02/14/2012-12:30:00: T3700G-52TQ(config)#system-time manual 02/14/2012-12:30:00 22.2 system-time ntp Description The system-time - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 162
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter timezone -- Your local time-zone, and it ranges from UTC-12:00 to UTC+13:00. The detailed information that each time-zone means - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 163
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide UTC+08:00-- TimeZone for Beijing, Chongqing, Hong Kong, Urumqi, NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163: T3700G-52TQ(config)# system-time ntp UTC-12:00 133.100.9.2 139.79.100.163 22.3 system - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 164
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the DST period of the switch as USA: T3700G-52TQ(config)#system-time dst predefined USA 22.4 system-time dst date Description The system-time dst date command is used to specify - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 165
-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure the DST start time as 00:00 am on April 1st of 2013, the end time as 00:00 am on October 1st of 2013 and the offset as 30 minutes: T3700G-52TQ(config)#system-time dst date Apr 1 00:00 2013 Oct - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 166
-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Specify the DST start time of the switch as 2:00 am on the first Sunday in May, the end time as 2:00 am on the last Sunday in October and the offset as 45 minutes: T3700G-52TQ(config)#system-time dst recurring first Sun - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 167
no contact-info Parameter contact_info -- Contact Information. It consists of 32 characters at most. It is www.tp-link.com by default. Command Mode Global Configuration Mode Example Configure the system contact information as www.tp-link.com: T3700G-52TQ(config)#contact-info www.tp-link.com 144 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 168
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.9 ip address Description This ip address command is used to configure the IP address and IP subnet mask for the specified interface manually. The interface type includes: routed port, loopback interface and VLAN interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 169
Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Enable the DHCP Client function on the Lay 3 routed port 1/0/1: T3700G-52TQ(config)# interface gigabitEthernet 1/0/1 T3700G-52TQ(config-if)# no switchport T3700G-52TQ(config-if)# ip address-alloc dhcp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 170
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter unitid -- Specify the unit in the stack to reboot. If not specified, reboot all members in the stack. Command Mode Privileged EXEC Mode Example Reboot all members in the stack: T3700G-52TQ#reboot 22.13 boot application Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 171
CLI Guide 22.14 copy running-config startup-config Description The copy running-config startup-config command is used to save the current settings as the startup configuration file. Syntax copy running-config startup-config Command Mode Privileged EXEC Mode Example Save current settings: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 172
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.16 copy startup-config usb Description to the USB stick and specify the configuration file location as usb://building/l3: T3700G-52TQ#copy startup-config usb usb://building/l3 22.17 copy tftp startup-config Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 173
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode Example Download the configuration file named as config to the switch as its startup configuration file from TFTP server with the IP 192.168.0.148: T3700G-52TQ#copy tftp startup-config ip-address 192.168 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 174
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter unitid -- Specify the member's Mode Example Delete the backup image files of all the members in the stack: T3700G-52TQ# remove backup-image 22.20 firmware upgrade Description The firmware upgrade command is used - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 175
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Reboot with the backup image? (Y/N): y 22. EXEC Mode Example Upgrade the uboot of all the switches in the stack: T3700G-52TQ#firmware upgrade bootloader 22.22 firmware upgrade xmodem Description The firmware upgrade xmodem - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 176
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.23 ping Description The ping command for ping test. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234. -n count -- The amount of times to send - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 177
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.24 tracert Description The the destination device. If the parameter ip/ipv6 is not selected, both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234. maxHops -- The maximum number of the route - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 178
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show system-time Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system time information of the switch: T3700G-52TQ#show system-time 22.26 show system-time detail Description The show system-time - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 179
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Display the NTP mode configuration information of the switch: T3700G-52TQ#show system-time ntp 22.28 show system-info Description The show system-info command is used to display system description, system name, device location - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 180
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide unitid -- Specify the unit in the usb Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the USB information: T3700G-52TQ#show usb 22.31 show files-in-usb Description The show files-in-usb command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 181
Gigabit Stackable L3 Managed Switch CLI Guide Example Display the directories and files in USB device: T3700G-52TQ#show files-in-usb 22.32 Any Configuration Mode Example Display the information of optical transceiver module: T3700G-52TQ#show fiber-ports 22.33 show image-info Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 182
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.34 show running-config Description The show Mode Example Display all the members' current operating configuration in the stack: T3700G-52TQ#show running-config 22.35 show startup-config Description The show startup-config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 183
Guide 22.36 show boot Description The show boot command is used to display the current boot configuration of the system. Syntax show boot Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system boot configuration information of the switch: T3700G-52TQ the trouble spot - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 184
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 22.38 show cpu-utilization Description The show Any Configuration Mode Example Display the CPU utilization information of the switch: T3700G-52TQ#show cpu-utilization 22.39 show memory-utilization Description The show memory - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 185
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 23 Ethernet Configuration Commands Ethernet Configuration Configuration Mode and configure Gigabit Ethernet port 20: T3700G-52TQ(config)#interface gigabitEthernet 1/0/20 23.2 interface range gigabitEthernet - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 186
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter port-list -- The list of Gigabit and 18 at the same time by adding them to one port-list: T3700G-52TQ(config)# interface range gigabitEthernet 1/0/10-11,1/0/18 23.3 interface ten-gigabitEthernet Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 187
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 23.4 interface range ten-gigabitEthernet Description and 26 at the same time by adding them to one port-list: T3700G-52TQ(config)# interface range ten-gigabitEthernet 1/0/49-50 23.5 description Description The description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 188
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter string -- Content of a port description, ranging from 1 to 16 characters. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 189
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 23.7 flow-control Description The flow-control command flow-control function for Gigabit Ethernet port 20: T3700G-52TQ(config)#interface gigabitEthernet 1/0/20 T3700G-52TQ(config-if)#flow-control 23.8 duplex Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 190
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide default the Gigabit Ethernet port is auto-negotiation mode and the Ten Gigabit Ethernet port is full-dulplex mode. Command Mode Interface Configuration Mode (interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 191
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 23.10 speed Description The speed command is the Speed Mode as 100Mbps for Gigabit Ethernet port 20: T3700G-52TQ(config)#interface gigabitEthernet 1/0/20 T3700G-52TQ(config-if)#speed 100 23.11 storm-control Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 192
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter broadcast -- The Broadcast control function allows the switch to filter broadcast in the network. If the transmission rate of the broadcast packets exceeds the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 193
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax bandwidth egress rate no bandwidth Parameter rate -- Specify the bandwidth for sending packets. Range: 1-1000000 kbps for the gigaport, 1 to 10000000 kbps for the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 194
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Clear the statistic information of all Ethernet ports: T3700G-52TQ(config)#clear counters Clear the statistic information of port 1/0/3: T3700G-52TQ(config)#clear counters interface gigabitEthernet 1/0/3 23.14 show interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 195
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show interface counters [ gigabitEthernet port | ten-gigabitEthernet port | port-channel lagid ] Parameter port --The port number or port list. lagid -- The ID of LAG. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 196
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#show interface configuration gigabitEthernet 1/0/20 23. Display the storm-control information of port Gigabit Ethernet port 1/0/20: T3700G-52TQ(config)#show storm-control interface gigabitEthernet 1/0/20 23.18 show bandwidth - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 197
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bandwidth-limit information of Gigabit Ethernet port 1/0/20: T3700G-52TQ(config)#show bandwidth interface gigabitEthernet 1/0/20 174 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 198
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 24 Class of Service Commands CoS (Class of Service) function is used to optimize the network performance. It provides you with network service experience of a better quality. The switch implements three priority - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 199
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 24.2 classofservice priority Description The classofservice priority command is used to configure CoS (Class of Service) based on port. To return to the default configuration, please use no classofservice priority command. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 200
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide based on 802.1p priority TC0-TC6, the bigger value, the higher priority. Example Map CoS 5 to TC 2.: T3700G-52TQ(config)#classofservice queue cos-map 5 2 24.4 classofservice queue dscp-map Description The classofservice queue - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 201
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax classofservice queue dscp-map dscp- the bigger value, the higher priority. Example Map DSCP values 10-12 to TC2: T3700G-52TQ(config)#classofservice queue dscp-map 10-12 2 24.5 classofservice queue mode Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 202
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter sp -- Strict-Priority Mode. In this mode, A value of 0 means there is no guaranteed minimum bandwidth in effect (best-effort service). The default value is 0. The sum of all bandwidth values for the queues must not - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 203
-Port Gigabit Stackable L3 Managed Switch CLI Guide bw -- The minimum bandwidth percentage for queue, ranging from 0 to 100 in increments of 1. By default, it is 0. Command Mode Global Configuration Mode Example Map CoS 5 to TC 2.: T3700G-52TQ(config)#classofservice queue min-bandwith 5 2 24.7 show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 204
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of IEEE 802.1p Priority and the mapping relation between cos-id and tc-id: T3700G-52TQ#show classofservice cos-map 24.9 show classofservice dscp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 205
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 24.11 show classofservice queue trust Description The show classofservice queue trust command is used to display the class of service trust mode information. Syntax show classofservice queue trust Command Mode Privileged - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 206
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 25 Differentiated Services Commands Differentiated Services (DiffServ) allows traffic to be classified into streams and given certain QoS treatment in accordance with defined per-hop behaviors. Packets are classified - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 207
Gigabit Stackable L3 Managed Switch CLI Guide Parameter class-map-name -- The name of an existing DiffServ class, ranging from 1 to 31 characters. Command Mode Global Configuration Mode Example Enter the Class-Map Config mode for class tp: T3700G-52TQ(config)#class-map tp 25.3 class-map match-all - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 208
CLI Guide Syntax class-map rename class-map-name new-class-map-name Parameter class-map-name -- The old name of the class. new-class-map-name --The new name of the class, ranging from 1 to 31 characters. Command Mode Global Configuration Mode Example Rename class "tp" as class "Market": T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 209
Mode Example Create a class whose name is "Market", add the match criteria based on class "tp": T3700G-52TQ(config)#class-map match-all Market T3700G-52TQ(config-cmap)#match class-map tp 25.7 match dstl4port Description The match dstl4port command definites a match condition based on the destination - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 210
The supported port keyword (domain / echo / ftp / ftpdata / http / smtp / snmp / telnet / tftp / www). Command Mode Class-Map Configuration Mode Example Create a class whose name is "Market", definites a match condition that the packets's source TCP/UDP port number should be 80: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 211
Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Class-Map Configuration Mode Example Create a class whose name is "Market", definites a match condition that the packets should match TCP protocol: T3700G-52TQ(config)#class-map match-all Market T3700G-52TQ(config-cmap)#match protocol TCP 25 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 212
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax match srcip6 source-ipv6 /prefix-length Parameter source-ipv6 -- The source IPv6 address. prefix-length -- The prefix length of the source IPv6 address. Command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 213
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.13 match T3700G-52TQ(config)#class-map match-all Market ipv6 T3700G-52TQ(config-cmap)#match ip6flowlbl 1000 25.14 match cos Description The match cos command definites a match condition based on the Class of Service - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 214
Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#class-map match-all Market ipv4 T3700G-52TQ(config-cmap)#match cos 3 25.15 match secondary-cos Description The match secondary-cos command definites a match condition based on the secondary Class of Service(Cos) value (the secondary 802 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 215
Stackable L3 Managed Switch CLI Guide Command Mode Class-Map Configuration Mode Example Create an IPv4 class whose name is "Market", definites a match condition that the destination MAC address should be 01:80:c2:00:00:00, the mask should be ff:ff:ff:00:00:00: T3700G-52TQ(config)#class-map match - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 216
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.18 match dstip Description The match dstip command definites a match condition based on the destination IPv4 address of a packet. The match condition only apply - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 217
L3 Managed Switch CLI Guide Example Create an IPv4 class whose name is "Market", definites a match condition that the packets's source IPv4 address should be192.168.0.123, the mask should be 255.255.255.0: T3700G-52TQ(config)#class-map match-all Market ipv4 T3700G-52TQ(config-cmap)#match srcip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 218
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax match ip { dscp | precedence | tos } value Parameter value(dscp) -- Enter a DSCP value in the range of 0 to 63. value(precedence) -- Enter an IP precedence - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 219
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.23 match secondary vlan Description The match secondary vlan command definites a match Mode Global Configuration Mode Example Enter the Policy-Map Config mode for a policy named tp: T3700G-52TQ(config)#policy-map - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 220
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.25 policy-map in Description The policy Mode Global Configuration Mode Example Create a policy named tp and specify it to inbound traffic: T3700G-52TQ(config)#policy-map tp in 25.26 policy-map out Description The policy- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 221
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.27 class Description The class command is Create a policy named tp and specify it to inbound traffic, then add a class named market to the policy: T3700G-52TQ(config)#policy-map tp in T3700G-52TQ(config-pmap)#class market - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 222
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap-c)#assign-queue 3 25.29 conform-color Description The conform-color command is used to enable color-aware traffic policing so that the matching - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 223
. Drop the packets matching class named market: T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap-c)#drop 25.31 mark cos Description The mark cos command is used to mark the matching packets with the specified Class of Service (CoS) value(the only tag in - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 224
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 25.32 mark cos-as-sec-cos Configuration Mode. Mark CoS value as secondary CoS value: T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap-c)#mark cos-as-sec-cos 25.33 mirror - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 225
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap-c)#mirror 1/0/3 25.34 redirect Description The redirect command is used to redirect copies of matching packets to the specific port. Syntax - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 226
CLI Guide Command Mode Policy-Class-Map Configuration Mode Example Enter the Policy-Map Config mode for a policy named tp, then add a class named market to the policy and enter Policy-Class-Map Configuration Mode. Redirect copies of matching packets to LAG 3: T3700G-52TQ(config)#policy-map tp T3700G - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 227
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide cos -- The Class of Service(Cos) value in an Ethernet frame header, ranging drop the nonconforming traffic: T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap-c)#simple 1000 100 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 228
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide -- Transmit the conforming traffic. cos -- The Class of Service(Cos) value in an Ethernet frame header, ranging from 0 as drop: T3700G-52TQ(config)#policy-map tp T3700G-52TQ(config-pmap)#class market T3700G-52TQ(config-pmap - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 229
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide -- Transmit the conforming traffic. cos -- The Class of Service(Cos) value in an Ethernet frame header, ranging from 0 Enter the Policy-Map Config mode for a policy named tp, then add a class named market to the policy and - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 230
31 alphanumetric characters. Command Mode Global Configuration Mode Example Apply a policy named tp to inbound traffic globally: T3700G-52TQ(config)#service-policy tp in 25.40 service-policy (interface) Description The service-policy command is used to apply a specific policy to inbound or outbound - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 231
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no service-policy { in | out } policy-map-name Parameter service-policy-name policy named tp to inbound traffic on port 5: T3700G-52TQ(config)#interface gigabitEthernet 1/0/5 T3700G-52TQ(config-if)#service-policy tp in 25.41 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 232
Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the policy summary information: T3700G-52TQ(config)#show diffserv service brief 25.43 show diffserv service Description The show diffserv service command is used to display the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 233
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all the Diffserv classes: T3700G-52TQ(config)#show class-map 25.45 show policy-map Description The show policy-map command is used to display - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 234
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of policy applied to port 1/0/10 and inbound traffic: T3700G-52TQ(config)#show policy-map interface 1/0/10 in 25.47 show policy-map interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 235
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 26 Port Mirror Commands Port Mirror refers to the process of forwarding copies of packets from one port to a monitoring port. Usually, the monitoring - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 236
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 26.2 monitor session source interface Description be link-aggregation member. Example Create monitor session 1, then configure Gigabit Ethernet port 4 as monitored ports and enable ingress monitoring: T3700G-52TQ(config)# - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 237
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Delete the Gigabit Ethernet port 4 in monitor session 1 and its configuration: T3700G-52TQ(config)#no monitor session 1 source interface gigabitEthernet 1/0/4 rx 26.3 show monitor session Description The show monitor session command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 238
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 27 Port Protection Commands This feature is Example Give a description "GroupA" for the protected ports group 1: T3700G-52TQ(config)# switchport protected 1 name GroupA 27.2 switchport protected Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 239
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax switchport protected group-num no switchport protected group-num Parameter group-number -- Specify a protected ports group for configuration. The valid value is 0 to 2. Command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 240
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 28 Loopback Detection Commands With loopback detection Configuration Mode Example Enable the loopback detection function globally: T3700G-52TQ(config)# loopback-detection 28.2 loopback-detection interval Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 241
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Specify the interval-time as 50 seconds: T3700G-52TQ(config)# loopback-detection interval 50 28.3 loopback-detection recovery-time Description The loopback-detection recovery-time command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 242
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax loopback-detection no loopback- Syntax loopback-detection config process-mode { alert | port-based } recovery-mode { auto | manual } Parameter alert | port-based -- The mode how the switch processes the detected loops. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 243
Switch CLI Guide interface ten-gigabitEthernet / interface range ten-gigabitEthernet / interface port-channel) Example Configure the loopback detection process-mode as port-based and recovery-mode as manual for port 2: T3200G-52TQ(config)# interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 244
Switch CLI Guide global status, loopback detection interval and loopback detection recovery time. Syntax show loopback-detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of loopback detection function: T3700G-52TQ# show loopback - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 245
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 29 ACL Commands ACL (Access 31 characters. Command Mode Global Configuration Mode Example Add a time-range named tSeg1: T3700G-52TQ (config)# time-range tSeg1 29.2 absolute Description The absolute command is used to - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 246
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter start-date -- The start date in Absoluteness range tSeg1 with time from May 5, 2012 to Oct. 5, 2012: T3700G-52TQ(config)# time-range tSeg1 T3700G-52TQ(config-time-range)# absolute start 05/05/2012 end 10/05/2012 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 247
Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#time-range tSeg1 T3700G-52TQ(config-time-range)#periodic week- Mode Global Configuration Mode Example Create a standard-IP ACL whose ID is 12: T3700G-52TQ(config)#access-list create 12 29.5 mac access-list Description The mac access-list - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 248
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is tplink: T3700G-52TQ(config)#mac access-list tplink 29.6 access-list standard Description The access-list standard command is used to add Standard-IP ACL rule - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 249
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide redirect-port -- The Destination and the packets match this rule will be forwarded by the switch: T3700G-52TQ(config)#access-list create 12 T3700G-52TQ(config)#access-list standard 12 rule 10 permit sip 192.168.0.100 smask - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 250
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide source-ip -- The source IP address contained in the rule. source-ip-mask -- The source IP address mask. It is required if you typed the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 251
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: T3700G-52TQ(config)#access-list create 110 T3700G-52TQ(config)#access-list extended 110 rule 10 permit - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 252
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide vlan-id -- The VLAN ID, ranging from 1 to , and the packets match this rule will be forwarded by the switch: T3700G-52TQ(config)#mac access-list tplink T3700G-52TQ(config-mac-acl)#rule 10 permit smac 00:01:3F:48:16:23 smask - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 253
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#access-list bind acl acl1 29.10 access-list bind acl(vlan) Description The access-list bind acl command is used to bind - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 254
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Resequence rules of the ACL 20, specify the starting sequence number as 1, the increment of sequence numbers as 5: T3700G-52TQ# access-list resequence 20 1 5 29.12 show time-range Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 255
Switch CLI Guide 29.14 show access-list bind Description The show access-list bind command is used to display the ACL binding information. Syntax show access-list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ACL binding information: T3700G-52TQ#show access - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 256
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 30 MSTP Commands MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 257
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the STP function for Gigabit Ethernet port 1/0/2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#spanning-tree 30.3 spanning-tree common-config Description The spanning-tree common-config command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 258
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide portfast -- Enable/ Disable Edge Port. By default, it is disabled. The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay. point-to-point -- The P2P link status, with auto, - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 259
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the spanning-tree mode as "mstp": T3700G-52TQ(config)#spanning-tree mode mstp 30.5 spanning-tree mst configuration Description The spanning-tree mst configuration command is used - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 260
CLI Guide Parameters instance-id -- Instance ID, ranging from 1 to 8. vlan-id -- The VLAN ID selected to mapping with the corresponding instance. Command Mode MST Configuration Mode Example Map the VLANs 1-100 to Instance 1: T3700G-52TQ(config)#spanning-tree mst configuration T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 261
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 30.8 revision Description The revision command is used to configure the revision level of MST instance. Syntax revision revision Parameters revision -- The revision level for - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 262
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the MST Instance 1 and configure its priority as 4096: T3700G-52TQ(config)#spanning-tree mst instance 1 priority 4096 30.10 spanning-tree mst Description The spanning-tree mst command is used to configure MST Instance - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 263
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 30.11 spanning-tree priority . Command Mode Global Configuration Mode Example Configure the bridge priority as 4096: T3700G-52TQ(config)#spanning-tree priority 4096 30.12 spanning-tree timer Description The spanning- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 264
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure forward-time max-age for Spanning Tree as 16 seconds and 22 seconds respectively: T3700G-52TQ(config)#spanning-tree timer forward-time 16 max-age 22 30.13 spanning-tree hold-count - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 265
Switch CLI Guide Parameter value -- The maximum number of hops that occur in a specific region before the BPDU is discarded, ranging from 1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Example Configure the max-hops of STP as 30: T3700G-52TQ(config)#spanning-tree - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 266
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide itself automatically as ERROR-PORT when it receives BPDU BPDU protect function for Gigabit Ethernet port 1/0/2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#spanning-tree bpduguard 30.17 spanning - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 267
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 30.18 spanning-tree guard loop Description The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 268
Stackable L3 Managed Switch CLI Guide interface ten-gigabitEthernet / interface range ten-gigabitEthernet / interface port-channel) Example Enable the Root Protect function for Gigabit Ethernet port 1/0/2: T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#spanning-tree guard - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 269
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax spanning-tree mcheck Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet / interface ten-gigabitEthernet / - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 270
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bridge parameters: T3700G-52TQ(config)#show spanning-tree bridge 30.24 show spanning-tree interface Description The show spanning-tree interface command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 271
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 30.25 show spanning-tree interface-security Description The show spanning-tree interface-security command is used to display the protect information of all ports - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 272
-Port Gigabit Stackable L3 Managed Switch CLI Guide port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the region information and mapping information of VLAN and MST Instance: T3700G-52TQ(config)#show spanning-tree mst configuration Display - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 273
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 31 IGMP Snooping Commands IGMP igmp snooping Command Mode Global Configuration Mode Example Enable IGMP Snooping function: T3700G-52TQ(config)#ip igmp snooping 31.2 ip igmp snooping(interface) Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 274
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable IGMP Snooping function of Gigabit Ethernet port 23: T3700G-52TQ(config)#interface gigabitEthernet 1/0/23 T3700G-52TQ(config-if)#ip igmp snooping 31.3 ip igmp snooping header-validation Description The ip igmp snooping - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 275
L3 Managed Switch CLI Guide Parameter rtime -- Specify the aging time in seconds, ranging from 0 to 3600. The default aging time is 0 second. Command Mode Global Configuration Mode Example Specify IGMP Snooping router port aging time as 100 seconds globally: T3700G-52TQ(config)# ip igmp snooping - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 276
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 31.6 ip igmp snooping mtime Description Configuration Mode Example Specify IGMP Snooping member port aging time as 100 seconds globally: T3700G-52TQ(config)# ip igmp snooping mtime 100 31.7 ip igmp snooping mtime(interface) - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 277
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Specify IGMP Snooping member port aging time as 100 seconds for Gigabit Ethernet port 1/0/3: T3700G-52TQ(config)#interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)# ip igmp snooping mtime 100 31.8 ip igmp snooping immediate - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 278
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface Mode Example Specify the operation of processing unknown multicast as "discard": T3700G-52TQ(config)#ip igmp snooping drop-unknown 31.11 ip igmp snooping vlan- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 279
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip igmp snooping vlan-config vlan-list [ immediate-leave | max-response-time max-response-time | rtime rtime | mtime mtime | rport interface { fastEthernet port | gigabitEthernet - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 280
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 31.12 ip igmp snooping querier Command Mode Global Configuration Mode Example Enable the IGMP Snooping Querier function: T3700G-52TQ(config)#ip igmp snooping querier 31.13 ip igmp snooping querier address Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 281
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 31.14 ip igmp snooping querier Mode Global Configuration Mode Example Configure the Query message interval time as 60 seconds: T3700G-52TQ(config)#ip igmp snooping querier query-interval 60 31.15 ip igmp snooping querier - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 282
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the IGMP Querier timer expiration period as 70 seconds: T3700G-52TQ(config)#ip igmp snooping querier timer expiry 70 31.16 ip igmp snooping querier version Description The ip igmp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 283
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no ip igmp snooping querier vlan vlan-id [ address | election participate ] Parameter vlan-id -- VLAN ID, ranging from 1 to 4093. ip-addr -- Specify the source - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 284
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 31.19 show ip igmp snooping interface Description Mode Example Display the IGMP basic configuration of Gigabit Ethernet port 2: T3700G-52TQ#show ip igmp snooping interface gigabitEthernet 1/0/2 basic-config Display the IGMP - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 285
Gigabit Stackable L3 Managed Switch CLI Guide Parameter vlan-id --The VLAN ID selected to display, ranging from 1 to 4093. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IGMP snooping configuration information of VLAN 2: T3700G-52TQ#show ip igmp snooping vlan 2 31 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 286
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip igmp snooping querier [ detail Any Configuration Mode Example Display the configurations of IGMP Snooping Querier of VLAN 2: T3700G-52TQ(config)#show ip igmp snooping querier vlan 2 31.24 show ip igmp profile - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 287
Stackable L3 Managed Switch CLI Guide Syntax show ip igmp profile [ id ] Parameter id -- Specify the ID of the profile, ranging from 1 to 999. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of all profiles: T3700G-52TQ(config)# show ip igmp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 288
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 32 MLD Snooping Commands MLD Snooping mld snooping Command Mode Global Configuration Mode Example Enable MLD Snooping function: T3700G-52TQ(config)#ipv6 mld snooping 32.2 ipv6 mld snooping(interface) Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 289
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable MLD Snooping function of Gigabit Ethernet port 23: T3700G-52TQ(config)#interface gigabitEthernet 1/0/23 T3700G-52TQ(config-if)#ipv6 mld snooping 32.3 ipv6 mld snooping rtime Description The ipv6 mld snooping rtime command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 290
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet / interface gigabitEthernet / interface range gigabitEthernet/ interface ten-gigabitEthernet / interface range ten- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 291
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter mtime -- Specify the aging time in seconds, ranging from 2 to 3600. The default aging time is 260 seconds. Command Mode Interface Configuration Mode (interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 292
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.8 ipv6 mld snooping max-response-time Description time as 15 seconds for Gigabit Ethernet port 1/0/3: T3700G-52TQ(config)#interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)#ipv6 mld snooping max-response-time 15 32 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 293
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.10 ipv6 mld snooping vlan-config Description The ipv6 mld snooping vlan- the MLD Snooping function and modify Member Port Time as 200 seconds for VLAN1-3: T3700G-52TQ(config)#ipv6 mld snooping vlan-config 1-3 mtime 200 270 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 294
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.11 ipv6 mld snooping querier Description Command Mode Global Configuration Mode Example Enable the MLD Snooping Querier function: T3700G-52TQ(config)#ipv6 mld snooping querier 32.12 ipv6 mld snooping querier address - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 295
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.13 ipv6 mld snooping querier Mode Global Configuration Mode Example Configure the Query message interval time as 60 seconds: T3700G-52TQ(config)#ipv6 mld snooping querier query-interval 60 32.14 ipv6 mld snooping querier - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 296
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the IGMP Querier timer expiration period as 70 seconds: T3700G-52TQ(config)#ipv6 mld snooping querier timer expiry 70 32.15 ipv6 mld snooping querier vlan Description The ipv6 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 297
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.16 ipv6 mld profile Description The ranging from 1 to 999. Command Mode Global Configuration Mode Example Create the profile 1: T3700G-52TQ(config)# ipv6 mld profile 1 32.17 deny Description The deny command is used to - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 298
Switch CLI Guide 32.18 permit Description The permit command is used to configure the filtering mode of profile as permit. Syntax permit Command Mode Profile Configuration Mode Example Configure the filtering mode of profile 1 as permit: T3700G-52TQ(config)# ipv6 mld profile 1 T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 299
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure one of the filter multicast address entry as range ff80::1234 to ff80::1235 in profile 1: T3700G-52TQ(config)# ipv6 mld profile 1 T3700G-52TQ(config-igmp-profile)#range ff80::1234 ff80::1235 32.20 ipv6 mld filter Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 300
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ#show ipv6 mld snooping 32.22 show ipv6 mld Mode Example Display the IGMP basic configuration of Gigabit Ethernet port 2: T3700G-52TQ#show ipv6 mld snooping interface gigabitEthernet 1/0/2 basic-config Display the IGMP basic - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 301
Switch CLI Guide Syntax show ipv6 mld snooping vlan [ vlan-id ] Parameter vlan-id --The VLAN ID selected to display, ranging from 1 to 4093. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the MLD Snooping configuration information of VLAN 2: T3700G-52TQ#show ipv6 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 302
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.25 show ipv6 mld snooping querier EXEC Mode and Any Configuration Mode Example Display MLD Snooping Querier detailed information: T3700G-52TQ(config)# show ipv6 mld snooping querier detail 32.26 show ipv6 mld snooping - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 303
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 32.27 show ipv6 mld profile Description Mode and Any Configuration Mode Example Display the configuration information of all profiles: T3700G-52TQ(config)# show ipv6 mld profile 32.28 clear ipv6 mld snooping statistics - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 304
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 33 MVR Commands MVR (Multicast VLAN Registration) is intended to solve the problem of receivers in different VLANs. It uses a dedicated manually configured VLAN, called the multicast VLAN to forward multicast traffic - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 305
Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#mvr 33.3 mvr Command Mode Global Configuration Mode Example Specify the MVR mode type as dynamic: T3700G-52TQ(config)#mvr mode dynamic 33.4 mvr vlan Description The mvr vlan command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 306
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#mvr vlan 2 33.5 mvr vlan(interface MVR multicast group as 224.1.1.1 for Gigabit Ethernet port 2 : T3700G-52TQ(config)#interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)#mvr vlan 2 group 224.1.1.1 33.6 mvr group Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 307
L3 Managed Switch CLI Guide count --The number of incremental multicast groups being added, ranging from 1 to 256. Command Mode Global Configuration Mode Example Set the MVR multicast group as 224.1.1.1, the number of incremental multicast groups being added is 10: T3700G-52TQ(config)# mvr group 224 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 308
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 33.8 mvr immediate Description The mvr immediate immediate leave mode for Gigabit Ethernet port 23: T3700G-52TQ(config)#interface gigabitEthernet 1/0/23 T3700G-52TQ(config)#mvr immediate 33.9 show mvr Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 309
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 33.10 show mvr interface Description The Mode Example Display the configuration of MVR for Gigabit Ethernet port 2: T3700G-52TQ#show mvr interface gigabitEthernet 1/0/2 33.11 show mvr members Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 310
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 33.12 show mvr traffic Description The show mvr traffic command is used to display and Any Configuration Mode Example Display statistical information about IGMP packets intercepted by MVR: T3700G-52TQ#show mvr traffic 287 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 311
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 34 Static Multicast MAC Address Table Commands Static multicast MAC address table allows you to create static multicast entries and view Multicast Forwarding Database ( - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 312
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 34.2 show multicast mac-address-table Description The show multicast mac-address-table command is used to display Multicast Forwarding Database (MFDB) table information. Syntax - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 313
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 35 SNMP Commands SNMP (Simple Network Management Protocol) functions are used to manage the network devices for a smooth communication, which can facilitate the network - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 314
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.2 snmp-server group Description The snmp-server group command is used to manage and configure the SNMP group. To delete the corresponding SNMP group, - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 315
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide notify -- Notify view. The management station software messages sent by View Default can be received by Management station: T3700G-52TQ(config)#snmp-server group group1 smode v3 slev authNoPriv read Default write Default notify - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 316
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide local | remote -- User Type, with local and remote as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: T3700G-52TQ(config)#snmp-server user admin group2 local cmode MD5 cpwd 11111 emode DES epwd 22222 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 317
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax snmp-server community name { read-only | read-write public, and the community has read-write management right to View Default: T3700G-52TQ(config)#snmp-server community public read-write Default 35.5 snmp-server host - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 318
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide smode -- The Security Model of the management for the switch to wait as 1000 seconds, and the retries time as 100: T3700G-52TQ(config)#snmp-server host 192.168.0.146 162 admin smode v2c type inform retries 100 timeout - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 319
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax snmp-server engineID { [local local- no snmp-server traps command. Syntax snmp-server traps [ cpu-threshold | fan | inventory | link-mode | mac-lock-violation | memory-threshold | multi-users | pim | power | spanning- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 320
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter cpu-threshold -- Enable SNMP 80%. fan -- Enable SNMP fan traps. inventory -- Enable card/stack/SFS traps. link-mode -- Enable SNMP Link up/down traps. mac-lock-violation -- Enable SNMP mac-lock-violation traps. It - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 321
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.8 snmp-server traps ospf all all Command Mode Global Configuration Mode Example Enable all the OSPF traps for the switch: T3700G-52TQ(config)# snmp-server traps ospf all 35.9 snmp-server traps ospf errors Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 322
Managed Switch CLI Guide virt-bad-packet --Enable packet parse failure traps on virtual interfaces. virt-config-error -- Enable config mismatch errors on virtual interfaces. Command Mode Global Configuration Mode Example Enable authentication-failure traps for the switch: T3700G-52TQ(config)# snmp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 323
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.11 snmp-server traps ospf the number of LSAs in the link-state database overflows. Command Mode Global Configuration Mode Example Enable all the overflow traps for the switch: T3700G-52TQ(config)# snmp-server traps ospf - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 324
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter all -- Enable all the retransmit traps. packets Global Configuration Mode Example Enable all the retransmit traps for the switch: T3700G-52TQ(config)# snmp-server traps ospf retransmit all 35.13 snmp-server traps - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 325
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.14 snmp-server traps link-status Description The snmp-server traps link-status command is used to enable SNMP link status trap for the specified port. To disable the sending of SNMP link status trap, please use no snmp- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 326
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide port -- The Fast/Gigabit/Ten-Gigabit Ethernet port as 1/0/2 and the sample interval as 100 seconds for the entry 1: T3700G-52TQ(config)#rmon history 1 interface gigabitEthernet 1/0/2 interval 100 owner owner1 35.16 rmon - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 327
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide indicates sending trap messages to the management the type of event as log and the owner of the event as "owner1": T3700G-52TQ(config)#rmon event 1 community community1 description description1 type log owner owner1 35.17 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 328
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide s-type -- Sample Type, which is the sampling method for the selected variable and as owner1 and the alarm intervals as 100 seconds for rmon alarm entry 1: T3700G-52TQ(config)#rmon alarm 1 owner owner1 interval 100 305 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 329
Guide 35.18 show snmp-server traps global Description The show snmp-server traps global command is used to display SNMP traps globally. Syntax show snmp-server traps global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display SNMP traps globally: T3700G-52TQ : T3700G-52TQ#show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 330
Gigabit Stackable L3 Managed Switch CLI Guide Example Display link status traps for the ports: T3700G-52TQ#show snmp-server traps port Privileged EXEC Mode and Any Configuration Mode Example Display the Group table: T3700G-52TQ#show snmp-server group 35.23 show snmp-server user Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 331
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the User table: T3700G-52TQ#show snmp-server user 35.24 show snmp-server community Description The show snmp-server community command is used to display the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 332
Switch CLI Guide 35.26 show snmp-server engineID Description The show snmp-server engineID command is used to display the engineID of the SNMP. Syntax show snmp-server engineID Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the engineID: T3700G-52TQ#show snmp-server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 333
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 35.28 show rmon event Description The Privileged EXEC Mode and Any Configuration Mode Example Display the Event configuration of entry1: T3700G-52TQ#show rmon event 1 35.29 show rmon alarm Description The show rmon alarm - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 334
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 36 LLDP Commands LLDP function it is 4. Command Mode Global Configuration Mode Example Specify Hold Multiplier as 5: T3700G-52TQ(config)#lldp hold-multiplier 5 36.2 lldp timer Description The lldp timer command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 335
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax lldp timer { tx-interval tx-interval | reinit-delay reinit-delay | notify-interval notify-interval } no lldp timer { tx-interval | reinit-delay | notify-interval } Parameter - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 336
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable Gigabit Ethernet port 1/0/1 to receive LLDPDU: T3700G-52TQ(config)#interface gigabitEthernet 1/0/1 T3700G-52TQ(config-if)#lldp receive 36.4 lldp transmit Description The lldp transmit command is used to enable the designated - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 337
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode ( [ system-name ] [ management-address ] [ port-vlan ] [ protocol-vlan ] [ vlan-name ] [ link-aggregation ] [ max-frame-size ] [ all ] } no lldp tlv-select { [ port-description ] [ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 338
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 36.7 lldp med-fast-count default, it is 3. Command Mode Global Configuration Mode Example Specify Fast Start Count as 5: T3700G-52TQ(config)# lldp med-fast-count 5 36.8 lldp med-status Description The lldp med-status command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 339
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the LLDP-MED feature for port 1/0/2: T3700G-52TQ(config)# interface gigabitEthernet 1/0/2 T3700G-52TQ(config-if)# lldp med-status 36.9 lldp med-tlv-select Description The lldp med-tlv-select command is used to configure - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 340
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of LLDP: T3700G-52TQ#show lldp 36.11 show lldp interface Description The show lldp interface command is used to display LLDP configuration - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 341
-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter port -- The Fast/Gigabit/Ten-Gigabit Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP information of Gigabit Ethernet port 1/0/1: T3700G-52TQ#show lldp local-information interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 342
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show lldp traffic interface [ fastEthernet port | gigabitEthernet Display the LLDP statistic information of Gigabit Ethernet port 1/0/1: T3700G-52TQ#show lldp traffic interface gigabitEthernet 1/0/1 36.15 clear lldp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 343
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 37 Static Routes the VLAN. Command Mode Global Configuration Mode Example Create the VLAN interface 2: T3700G-52TQ(config)# interface vlan 2 37.2 interface loopback Description This interface loopback command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 344
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Create the loopback interface 1: T3700G-52TQ(config)# interface loopback 1 37.3 interface range port-channel Description This interface range port-channel command is used to create multiple - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 345
-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter port-channel-id -- The ID of the port-channel interface, ranging from 1 to 64. Command Mode Global Configuration Mode Example Create the port-channel interface 1: T3700G-52TQ (config)# interface port-channel 1 37.5 switchport Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 346
Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax shutdown no shutdown Command Mode Interface Configuration Mode Example Shut down the routed port 1/0/9 : T3700G-52TQ(config)# interface gigabitEthernet 1/0/9 T3700G-52TQ(config-if)# no switchport T3700G-52TQ(config-if)# shutdown 37.7 ip route - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 347
Guide 37.8 ip routing Description This ip routing command is used to enable the Lay 3 routing function. To disable this function, please use the no ip routing command. Syntax ip routing no ip routing Command Mode Global Configuration Mode Example Disable the Layer 3 ip routing function : T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 348
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 37.10 show ip interface Description and Any Configuration Mode Example Display the detailed information of the VLAN interface 2: T3700G-52TQ(config)# show ip interface vlan 2 37.11 show ip interface brief Description This - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 349
Stackable L3 Managed Switch CLI Guide Example Display the summary information of the Layer 3 interfaces: T3700G-52TQ(config)# show ip interface Privileged EXEC Mode and Any Configuration Mode Example Display the static routes: T3700G-52TQ(config)# show ip route static 37.13 show ip route specify - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 350
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter ip -- Specify the destination IP address. mask .255.0 Display the routes to all the subnets that belongs to 192.168.0.0/16: T3700G-52TQ(config)# show ip route specify 192.168.0.0 255.255.0.0 longer-prefix 37.14 show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 351
used to enable DHCP service globally. To disable DHCP server service, please use no service dhcp server command. Syntax service dhcp server no service dhcp server Command Mode Global Configuration Mode Example Enable DHCP server service globally: T3700G-52TQ(config)# service dhcp server 38.2 option - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 352
L3 Managed Switch CLI Guide Command Mode DHCP Configuration Mode Example Set the extend option code as 100, the extend option type as ip address, the extend option value as 192.168.10.1 in the address pool "product": T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(config-dhcp)# option - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 353
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax extend-option vendor-class-id class another network segment as 34 in the address pool "product": T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(config-dhcp)# extend-option vendor-class-id 34 38.5 ip dhcp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 354
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 38.6 ip dhcp server exclude- Global Configuration Mode Example Set the reserved IP addresses from 192.168.1.1 to 192.168.1.9: T3700G-52TQ(config)# ip dhcp server exclude-address 192.168.1.1 192.168.1.9 38.7 ip dhcp server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 355
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter pool-name -- Specify the address pool name, ranging from 1 to 8 characters. Command Mode Global Configuration Mode Example Create the address pool of name POOL1: T3700G-52TQ(config)# ip dhcp server pool POOL1 38.8 ip dhcp server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 356
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax network network-address subnet-mask Parameter network-address -- Specify the network address of the pool, with the format A.B.C.D. All the IP addresses in the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 357
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax lease {days [hours [minutes] ] | infinite} Parameter days --Specify the days parameter of lease time, ranging from 0 to 59 days. hours --Specify the hours parameter - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 358
Gigabit Stackable L3 Managed Switch CLI Guide Command Mode DHCP Configuration Mode Example Reserve the IP address 192.168.0.10 in the address pool "product" for the device with the MAC address as 5e:4c:a6:31:24:01 and the hardware type as ethernet: T3700G-52TQ(config)# ip dhcp server pool product - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 359
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 38.14 default-gateway Description The default- product's default gateways as 192.168.0.1 and 192.168.1.1: T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(dhcp-config)# default-gateway 192.168.0.1,192.168.1.1 38. - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 360
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Specify the address pool's DNS servers as 192.168.0.1 and 192.168.1.1: T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(config-dhcp)# dns-server 192.168.0.1,192.168.1.1 38.16 ntp-server Description The ntp-server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 361
CLI Guide Parameter NBNS-list -- Specify the Netbios server list, with the format of A.B.C.D,E.F.G.H. At most 8 Netbios servers can be configured, separated by comma. Command Mode DHCP Configuration Mode Example Specify the address pool's Netbios servers as 192.168.0.1 and 192.168.1.1: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 362
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 38.19 next-server Description The next-server Example Specify the next server's IP address as 192.168.2.1: T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(config-dhcp)# next-server 192.168.2.1 38.20 domain-name - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 363
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Specify the DHCP client's domain name as edu: T3700G-52TQ(config)# ip dhcp server pool product T3700G-52TQ(config-dhcp)# domain-name edu 38.21 bootfile Description The bootfilecommand is used to specify the name of the DHCP client - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 364
Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all the address conflicts logged by the DHCP Server: T3700G-52TQ( EXEC Mode and Any Configuration Mode Example Display the status of DHCP service: T3700G-52TQ(config)# show ip dhcp server status 38.24 show ip dhcp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 365
CLI Guide 38.25 show ip dhcp server pool Description The show ip dhcp server pool command is used to display the configuration of the address pool. Syntax show ip dhcp server pool Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configured address pool: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 366
Stackable L3 Managed Switch CLI Guide Syntax show ip dhcp server binding [ ip ip-address ] Parameter ip-address -- Specify the binding IP address. Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the address binding entries: T3700G-52TQ(config)# show ip dhcp server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 367
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax clear ip dhcp server statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear the packet statistics: T3700G-52TQ(config)# clear ip dhcp server statistics 38.30 clear ip dhcp server binding Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 368
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 39 DHCP Relay A DHCP Relay service dhcp relay command. Syntax service dhcp relay no service dhcp relay Command Mode Global Configuration Mode Example Enable DHCP Relay function globally: T3700G-52TQ(config)# service - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 369
Guide Command Mode Interface Configuration Mode Example Add DHCP Server address 192.168.2.1 to interface VLAN 1: T3700G-52TQ(config)# interface vlan 1 T3700G-52TQ Mode Global Configuration Mode Example Enable option 82 support in DHCP Relay: T3700G-52TQ(config)# ip dhcp relay information 39.4 ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 370
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide drop: Discard the packet with the Option 82 Option 82 field with the local parameter on receiving the DHCP request packet: T3700G-52TQ(config)# ip dhcp relay information policy replace 39.5 ip dhcp relay information circuit - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 371
Managed Switch CLI Guide Syntax ip dhcp relay information remote-id remoteID no ip dhcp relay information remote-id Parameter remoteID -- Specify the remote ID, ranging from 1 to 32 characters. Command Mode Global Configuration Mode Example Specify the remote ID as "tplink": T3700G-52TQ(config)# ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 372
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 40 Proxy ARP Commands The switch uses Proxy ARP to help hosts learn MAC addresses of hosts on other networks or subnets. 40.1 ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 373
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no ip local-proxy-arp Command Mode Interface Configuration Mode Example Enable the Local Proxy ARP function on Interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip local-proxy-arp Enable the Local Proxy - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 374
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Local Proxy ARP status: T3700G-52TQ(config)# show ip local-proxy-arp 351 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 375
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 41 IGMP Commands Internet Group no ip igmp Command Mode Interface Configuration Mode Example Enable the IGMP function globally: T3700G-52TQ(config)#ip igmp 41.2 ip igmp(interface) Description The ip igmp command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 376
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the IGMP function on Interface VLAN 2: T3700G-52TQ(config)#interface vlan 2 T3700G-52TQ(config-if)#ip igmp 41.3 ip igmp header-validation Description The ip igmp header-validation command is used to enable the validation - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 377
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Configure the IGMP version as version 2 on Interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip igmp version 2 41.5 ip igmp last-member-query-count Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 378
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide interface. To restore to the default value on this Messages that the switch sends as 20 seconds on Interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip igmp last-member-query-interval 20 41.7 ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 379
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure the interval of General Query Messages that the switch sends as 50 seconds on interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip igmp query-interval 50 41.8 ip igmp query-max-response - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 380
CLI Guide Syntax ip igmp robustness robustness no ip igmp robustness Parameter robustness -- Specify the robustness of IGMP, ranging from 1 to 255. The default value is 2. Command Mode Interface Configuration Mode Example Configure the robustness of IGMP as 3 on Interface VLAN 2: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 381
Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip igmp query-interval 10 Messages that the switch sends as 3 on Interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip igmp last-member-query-count 3 41.12 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 382
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter id -- Specify the id of the configuration profile, ranging from 1 to 999. Command Mode Global Configuration Mode Example Create the profile 1: T3700G-52TQ(config)# ip igmp profile 1 41.13 deny Description The deny command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 383
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure the filtering mode of profile 1 as permit: T3700G-52TQ(config)# ip igmp profile 1 T3700G-52TQ(config-igmp-profile)#permit 41.15 range Description The range command is used to configure the range of the profile's filtering - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 384
Switch CLI Guide Syntax ip igmp filter profile-id no ip igmp filter profile-id Parameter profile-id -- Specify the profile ID to be bound. Command Mode Interface Configuration Mode Example Bind profile 1 to the Interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 385
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 41.18 show ip igmp profile EXEC Mode and Any Configuration Mode Example Display the configuration information of all profiles: T3700G-52TQ(config)# show ip igmp profile 41.19 show ip igmp groups Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 386
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 41.20 show ip igmp groups interface Display the detailed information of the dynamic multicast groups on the gigabitEthernet 1/0/1: T3700G-52TQ(config)# show ip igmp groups interface gigabitEthernet 1/0/1 detail 41.21 show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 387
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the dynamic multicast groups on interface VLAN 1: T3700G-52TQ(config)# show ip igmp groups interface vlan 1 41.22 show ip igmp interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 388
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip igmp interface vlan vlan-id [stats ] Parameter vlan-id -- Specify Mode Example Display the IGMP configuration information on the Interface VLAN 2: T3700G-52TQ(config)# show ip igmp interface vlan 2 365 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 389
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 42 PIM Commands The Protocol Command Mode Global Configuration Mode Example Enable the IP multicast routing function globally: T3700G-52TQ(config)#ip multicast-routing 42.2 ip pim (global) Description The ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 390
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable PIM dense mode globally: T3700G-52TQ(config)# ip pim dense-mode 42.3 ip pim (interface) Description The ip pim command is used to enable PIM on the specified interface. To disable - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 391
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter default -- Enable PIM SSM in the default Configuration Mode Example Enable PIM SSM function in the default multicast group: T3700G-52TQ(config)# ip pim ssm default 42.5 ip pim bsr-candidate interface Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 392
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the candidate BSR on interface VLAN 2: T3700G-52TQ(config)# ip pim bsr-candidate interface vlan 2 10 20 45 42.6 ip pim rp-candidate interface Description The ip pim rp-candidate - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 393
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)# ip pim rp-candidate interface vlan 2 Configure the IP address of the static RP as 20.20.20.2 in group 224.1.1.1/255.0.0.0: T3700G-52TQ(config)# ip pim rp-address 20.20.20.2 224.1.1.1 255.0.0.0 42.8 ip pim bsr-border - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 394
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip pim bsr-border no ip pim bsr-border Command Mode Interface Configuration Mode Example Configure the BSR border on VLAN interface 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip pim bsr-border 42.9 ip pim - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 395
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 42.10 ip pim join-prune-interval Description Configure the interval of join/prune packet as100s on vlan interface 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip pim join-prune-interval 100 42.11 ip pim - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 396
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Configure the interval of Hello packet of 100s on VLAN interface 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip pim hello-interval 100 42.12 show ip multicast Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 397
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide source ip-addr -- Displays the multicast routing table with EXEC Mode and Any Configuration Mode Example Display all IP multicast routing entries: T3700G-52TQ(config)# show ip mroute 42.14 show ip mfc Description The show ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 398
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip pim interface [{ fastEthernet | gigabitEthernet | ten-gigabitEthernet } port | vlanId vlan-id ] Parameter fastEthernet | gigabitEthernet | ten-gigabitEthernet -- The port type of the interface. port -- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 399
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)# show ip pim neighbor 42.17 show Mode Privileged EXEC Mode and Any Configuration Mode Example Display the BSR and RP settings: T3700G-52TQ(config)# show ip pim bsr-router 42.18 show ip pim rp mapping Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 400
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 42.19 show ip pim rp hash EXEC Mode and Any Configuration Mode Example Display the RP hash result of multicast group 224.1.1.2: T3700G-52TQ(config)# show ip pim rp hash 224.1.1.2 42.20 show ip pim ssm Description The show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 401
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 42.21 show ip pim statistic Description The show ip pim statistic command Privileged EXEC Mode and Any Configuration Mode Example Display the statistics of all PIM interfaces: T3700G-52TQ(config)# show ip pim statistic 378 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 402
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 43 Static Multicast Routing Commands Multicast routing table uses the RPF (Reverse Path Forwarding) mechanism to determine the upstream and downstream neighbors basing on - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 403
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 43.2 show ip mroute static Description The show ip mroute static command is used EXEC Mode and Any Configuration Mode Example Displays all the static multicast routing entries: T3700G-52TQ(config)# show ip mroute static 380 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 404
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 44 VRRP Commands The Virtual Router Redundancy protocol is designed to handle default router failures by providing a scheme to dynamically elect a backup router. The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 405
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 44.2 ip vrrp vrid virtual-ip Description This primary IP address as 192.168.0.7 for vrid 4 on interface VLAN 3: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config-if)#ip vrrp vrid 4 virtual-ip 192.168.0.7 44.3 ip vrrp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 406
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Add a secondary IP address as 192.168.0.8 for vrid 4 on interface VLAN 3: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config-if)#ip vrrp vrid 4 virtual-ip 192.168.0.8 44.4 ip vrrp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 407
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax ip vrrp vrid vrid priority pri no ip vrrp vrid Configure the priority for the interface VLAN 3 as 123 in vrid 4: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config-if)#ip vrrp vrid 4 priority 123 44.6 ip vrrp vrid - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 408
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure the advertisement interval for the interface VLAN 3 as 12 seconds in vrid 4: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config-if)#ip vrrp vrid 4 timer-advertise 12 44.7 ip vrrp vrid preempt-mode Description This - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 409
enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Configure the authentication Mode as md5 and configure the key as 123 for the interface VLAN 3 in vrid 4: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 410
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 44.9 ip vrrp vrid track interface Description This vlan2 and the priority decrement as 10 for the tracking interface: T3700G-52TQ(config)#interface vlan 3 T3700G-52TQ(config-if)#ip vrrp vrid 4 track interface vlan 2 reduce- - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 411
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax clear ip vrrp statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear all the statistics about vrrp on the switch: T3700G-52TQ(config)# clear ip vrrp statistics 44.11 show ip vrrp Description This - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 412
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 44.12 show ip vrrp statistics Description This command is used to display the statistics of a virtual router on a specified interface or all the virtual - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 413
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 45 RIP Commands The Routing Information Enable the RIP function and enter router configuration mode. T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# 45.2 network Description The network command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 414
Switch CLI Guide Parameter network number --The network number of the network, in the format of 192.168.0.0. Command Mode Router Configuration Mode (router rip) Example Enable RIP function on interfaces of the network 192.168.0.0: T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# network - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 415
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 45.4 timer basic Description The timer basic router rip) Example Configure the update timer as 80 seconds: T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# timer basic update 80 45.5 distance Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 416
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Router Configuration Mode (router rip) Example Configure the administrative distance of RIP as 20: T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# distance 20 45.6 auto-summary Description The auto-summary command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 417
CLI Guide Syntax default-metric metric no default-metric Parameter metric -- Specify the default metric, ranging from 1 to 15. By default, it is 1. Command Mode Router Configuration Mode (router rip) Example Configure the default metric of RIP as 5: T3700G-52TQ(config)# router rip T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 418
52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# redistribute static metric 5 45.9 poison-reverse Description The poison-reverse command is used to enable poison reverse function on the desired interface. To - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 419
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable split horizon function on the interface VLAN2: T3700G-52TQ(config)# router rip T3700G-52TQ(config-router)# split-horizon 45.11 ip rip receive version Description The ip rip receive version command is used to specify the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 420
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide (configured with version command) before you specify its own RIP send/receive version. the interface VLAN2 to send RIPv1 packets only: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip rip send version 1 45.13 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 421
L3 Managed Switch CLI Guide none -- Configure the authentication mode as none. Command Mode Interface Configuration Mode Example Configure the RIP authentication mode of interface VLAN2 as simple, and specify its key as 123: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip rip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 422
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 46 OSPF Commands OSPF is an Interior Gateway Protocol (IGP) designed expressly for IP networks, supporting router ID. If no router ID is configured manually or the configured router ID is deleted, the highest IP - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 423
Guide Syntax router-id router-id no router-id Parameter router-id -- The route ID in the format of dotted decimal notation. 0.0.0.0 is illegal. Command mode Router Configuration Mode Example Configure the router ID of OSPF routing process 1 as 1.1.1.1: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 424
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Configure the network 192.168.0.0/24 in the area 0.0.0.0: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# network 192.168.0.0 255.255.255.0 area 0.0.0.0 46.4 maximum-paths Description The maximum-paths command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 425
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide to default values, please use the no redistribute command with corresponding parameters. Syntax redistribute { connected | static | rip | ospf process-id } [ metric cost ] [ metric-type type ] [ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 426
Switch CLI Guide Syntax default-metric cost no default-metric Parameter cost -- The default cost of the redistributing external route, ranging form 1 to 16777214. Command Mode Router Configuration Mode Example Configure the default cost of the redistributing external route as 12: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 427
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide cost--The default cost of the default route, ranging form is default route is the IP routing table or not: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# default-information originate always 46.8 auto-cost - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 428
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Enable the auto computing function of the interface cost and configure the reference bandwidth as 10000 Mbps: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# auto-cost reference-bandwidth 10000 46.9 distance Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 429
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.10 timers throttle spf Description The timers the computing delay and interval of the SPF as 10 seconds: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# timers throttle spf 10 10 46.11 compatible rfc1583 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 430
52-Port Gigabit Stackable L3 Managed Switch CLI Guide no compatible rfc1583 Command Mode Router Configuration Mode Example Configure the OSPF's compatibility for the routing rules in RFC 1583: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# compatible rfc1583 46.12 passive-interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 431
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config-router)# passive-interface vlan 1 46.13 the interfaces from sending OSPF packets in routing process 1: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# passive-interface default 46.14 no area Description - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 432
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Delete the OSPF area 1: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)#no area 1 46.15 area stub Description The area stub command is used to define an area as a stub area. To restore the - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 433
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide any optional parameters. To restore Mode Router Configuration Mode Example Configure Area 1 as a total NSSA area: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# area 1 nssa no-summary 46.17 area default-cost - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 434
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide no area area-id default-cost Parameter area the cost of default summary route sent to Area 1 as 10: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# area 1 default-cost 10 46.18 area range Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 435
cost 10 in the Area 0: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# area 0 range 100.100.0.0 255.255.0.0 cost 10 46.19 area virtual-link Description The area virtual-link command is used to configure the virtual-link. To delete the configured virtual-link, please use the no area - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 436
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide hello-interval -- The interval of the hello packets T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# area 1 virtual-link 1.1.1.1 46.20 area virtual-link authentication Description The area virtual-link - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 437
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide message-digest -- Configure the T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config-router)# area 2 virtual-link 3.3.3.3 authentication 46.21 area virtual-link authentication-key Description The area virtual-link - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 438
CLI Guide Example Configure the authentication mode of a virtual-link as simple authentication, with the transmission area as Area 2 and the ID of the neighboring router on the other endpoint as 3.3.3.3, and the authentication key as 123456: T3700G-52TQ(config)# router ospf 1 T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 439
Switch CLI Guide Example Configure the authentication mode of a virtual-link as md5 authentication, with the transmission area as Area 2 and the ID of the neighboring router on the other endpoint as 3.3.3.3, with the authentication ID as 2 and the authentication key as 123456: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 440
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.24 ip ospf retransmit-interval Description Configure the retransmission interval of interface VLAN 2 as 10 seconds: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip ospf retransmit-interval 10 46.25 ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 441
CLI Guide Parameter delay-- The LSA transmission delay, ranging from 1 to 65535 seconds. The default value is 1 second. Command Mode Interface Configuration Mode Example Configure the LSA transmission delay of interface VLAN 2 as 2 seconds. T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 442
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.27 ip ospf hello-interval Description The ip of the hello packets sent on interface VLAN 2 as 20 seconds: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip ospf hello-interval 20 46.28 ip ospf dead-interval - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 443
Switch CLI Guide Parameter interval-- The neighbor's failure interval, ranging from 1 to 65535 seconds and the default is 4 times the hello interval. Command Mode Interface Configuration Mode Example Configure the neighbor's failure interval on interface VLAN 2 as 50 seconds: T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 444
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.30 ip ospf authentication-key Description The ip interface VLAN 2 as simple authentication, and the password as 123: T3700G-52TQ(config)#interface vlan 2 T3700G-52TQ(config-if)# ip ospf authentication-key 123 46.31 ip ospf - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 445
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter id -- The ID of the md5 authentication key, ranging from key ID as 1 and password as abc on interface VLAN 2: T3700G-52TQ(config)#interface vlan 2 T3700G-52TQ(config-if)# ip ospf message-digest-key 1 md5 abc 46.32 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 446
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config-if)# ip ospf network broadcast 46.33 Mode Example Block the flooding of the LSA packets on interface VLAN 2: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip ospf database-filter all out 46.34 ip ospf - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 447
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode Example Configure interface VLAN 2 to ignore the MTU field check in the DD exchange process: T3700G-52TQ(config)# interface vlan 2 T3700G-52TQ(config-if)# ip ospf mtu-ignore 46.35 clear ip ospf - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 448
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip ospf [ process-id ] Parameter and Any Configuration Mode Example Display the global information of all the OSPF processes: T3700G-52TQ# show ip ospf 46.37 show ip ospf database Description The show ip ospf - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 449
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 46.38 show ip ospf interface Description The show Mode Example Display the information of the interfaces in all the OSPF processes: T3700G-52TQ# show ip ospf interface 46.39 show ip ospf neighbor Description The show ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 450
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide detail-- The detailed information of the Mode and Any Configuration Mode Example Display the virtual links of all the OSPF processes: T3700G-52TQ# show ip ospf virtual-links 46.41 show ip ospf border-routers Description The - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 451
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip ospf [ process-id ] border- Privileged EXEC Mode and Any Configuration Mode Example Display the routing tables of OSPF: T3700G-52TQ# show ip route ospf 46.43 show ip ospf area database Description The show ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 452
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax show ip ospf process-id area area-id database [ Any Configuration Mode Example Display the LSDB summary information of Area 0 in process 1: T3700G-52TQ# show ip ospf 1 area 0 database 46.44 show ip ospf area interface - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 453
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Display the detailed information of all the interfaces of Area 0 in process 1: T3700G-52TQ# show ip ospf 1 area 0 interface 46.45 show ip ospf area neighbor Description The show ip ospf are neighbor command is used to display - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 454
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 47 SDM Template Commands This configure the SDM template. The SDM template is used to allocate system resources to best support the features being used in your application. The template change will takes effect after - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 455
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 47.2 show sdm prefer dual-ipv4-and-ipv6 default Description The show sdm prefer dual-ipv4-and-ipv6 default command is used to display parameters for the SDM template supports ipv4 routing and ipv6 routing. Syntax show sdm - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 456
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 48 AAA Commands AAA stands for list describes the authentication methods and their sequence to authenticate a user. The switch supports Login List for users to gain access to the switch, and Enable List for normal - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 457
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide time -- Specify the time in seconds the switch port as 1500, timeout as 6 seconds, and the unencrypted key string as 12345. T3700G-52TQ(config)# tacacs-server host 1.1.1.1 port 1500 timeout 6 key 12345 48.2 show tacacs-server - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 458
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Display the information of all the TACACS+ servers: T3700G-52TQ(config)# show tacacs-server 48.3 radius-server host Description The radius-server host command is used to configure a new RADIUS server. To delete the specified - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 459
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode User Guidelines 6 seconds, retransmit times as 3, and the unencrypted key string as 12345. T3700G-52TQ(config)# radius-server host 1.1.1.1 auth-port 1200 timeout 6 retransmit 3 key 12345 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 460
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide authentication method list, please use the no aaa authentication login command. Syntax priority1 method as radius and priority2 method as local: T3700G-52TQ(config)# aaa authenticaiton login defaultList radius local 48.6 aaa - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 461
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide methods and their sequence to elevate a user's privilege. To "defaultList" with the priority1 method as radius and priority2 method as enable: T3700G-52TQ(config)# aaa authenticaiton enable defaultList radius enable 438 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 462
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 48.7 aaa authentication dot1x default Description This server group is supported. Command Mode Global Configuration Mode Example Configure the default 802.1X authentication method as "radius": T3700G-52TQ(config)# aaa - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 463
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Configure the default 802.1X accounting method as "radius": T3700G-52TQ(config)# aaa accounting dot1x default radius 48.9 show aaa authentication Description This show aaa authentication - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 464
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the default 802.1X accounting method list: T3700G-52TQ(config)# show aaa accounting 48.11 line console Description The line console command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 465
CLI Guide Parameter method-list -- Specify the login method list on the console port. It is "noauthList" by default, which contains the method "none". Command Mode Line Configuration Mode Example Configure the login authentication method list on the console port as "defaultList": T3700G-52TQ(config - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 466
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 48.14 line telnet Description The line telnet Global Configuration Mode Example Enter the telnet terminal line configuration mode: T3700G-52TQ(config)#line telnet 48.15 login authentication(telnet) Description The login - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 467
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)#line telnet T3700G-52TQ(config-line)# login authentication defaultList 48.16 enable authentication(telnet) Description The enable authentication command is used to apply the privilege authentication method list to - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 468
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax line ssh Command Mode Global Configuration Mode Example Enter the ssh terminal line configuration mode: T3700G-52TQ(config)#line ssh 48.18 login authentication(ssh) Description The login authentication command is used to apply - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 469
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 48.19 enable authentication(ssh) Description The method list on the ssh terminal line as "defaultList": T3700G-52TQ(config)# line ssh T3700G-52TQ(config-line)# enable authentication defaultList 48.20 show aaa global - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 470
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the AAA function's global status and each application's method list: T3700G-52TQ(config)# show aaa global 447 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 471
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 49 ARP Commands Address ARP dynamic entry is automatically created and maintained by ARP. A static ARP entry is manually configured and maintained. 49.1 arp Description This arp command is used to add a static - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 472
JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax clear arp-cache Command Mode Privileged EXEC Mode Example Clear all the dynamic ARP entries: T3700G-52TQ (config)# clear arp-cache 49.3 arp timeout Description This arp timeout command is used to configure the ARP aging time. To - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 473
CLI Guide Syntax arp resptime resptime no arp resptime Parameter resptime -- Specify the ARP request response timeout, ranging from 1 to 10 seconds. The default value is 1 seconds. Command Mode Global Configuration Mode Example Configure the ARP request response timeout as 3 seconds: T3700G-52TQ - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 474
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 49.6 arp dynamic-renew Description This Command Mode Global Configuration Mode Example Enable automatic update of dynamic arp entries: T3700G-52TQ(config)#arp dynamic-renew 49.7 show arp Description This show arp command is - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 475
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 49.8 show ip arp (interface) Description This and Any Configuration Mode Example Display the ARP entry associated with VLAN interface 2 : T3700G-52TQ(config)# show ip arp vlan 2 49.9 show ip arp summary Description This show - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 476
-52TQ(config)# interface vlan 1 T3700G-52TQ(config-if)# ipv6 enable 50.2 ipv6 address autoconfig Description This command is used to enable the automatic configuration of the ipv6 link-local address. The switch has only one ipv6 link-local address, which can be configured automatically or manually - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 477
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide link-local address, the manually configured ipv6 link-local address will be deleted when the autoconfigured ipv6 link-local address takes effect. Syntax ipv6 address autoconfig Configuration Mode Interface Configuration Mode - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 478
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 50.4 ipv6 address dhcp Description The ipv6 address dhcp Mode Example Enable the DHCP Client function on VLAN interface 1: T3700G-52TQ(config)# interface vlan 1 T3700G-52TQ(config-if)# ipv6 address dhcp 50.5 ipv6 address ra - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 479
CLI Guide Example Enable the automatic ipv6 address configuration function to obtain IPv6 address through the RA message on VLAN interface 1: T3700G-52TQ(config)# interface vlan 1 T3700G-52TQ(config-if)# ipv6 address ra 50.6 ipv6 address eui-64 Description This command is used to manually configure - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 480
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 50.7 ipv6 address Description This command is used to manually configure a global IPv6 address on the interface. To remove a global IPv6 address from the interface, please use no ipv6 address command. Syntax ipv6 address - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 481
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide T3700G-52TQ(config)# show ipv6 interface 458 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 482
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 51 Management Port Commands 51.1 management-port Mode Example Specify the management port configuration protocol as DHCP: T3700G-52TQ(config)# management-port protocol dhcp 51.2 management-port protocol dhcp - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 483
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Global Configuration Mode Example Enable the management port to carry with client ID option (Option 61) when the management port obtains an IP address from the DHCP server: T3700G-52TQ(config)# management-port protocol dhcp client-id - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 484
Configuration Mode Example Enable the IPv6 function on the management port: T3700G-52TQ(config)# management-port ipv6 enable 51.5 management-port ipv6 address Description This management-port ipv6 address command is used to manually configure a global ipv6 address on the management port. To remove - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 485
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 51.6 management-port ipv6 address eui-64 Description This management-port ipv6 address ipv6-addr eui-64 command is used to manually configure a global IPv6 address with an extended unique identifier (EUI) in the low-order 64 - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 486
L3 Managed Switch CLI Guide Parameter ipv6-addr -- Specify the ipv6 gateway address of the management port. Command Mode Global Configuration Mode Example Specify the ip address of the management port as 192.168.10.1,and the subnet mask as 255.255.255.0: T3700G-52TQ(config)# management-port ip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 487
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide address on the management port, please use no management-port ipv6 address autoconfig command. Syntax management-port ipv6 address autoconfig no management-port ipv6 address - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 488
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Chapter 52 Auto VoIP Commands The no auto-voip Command Mode Global Configuration Mode Example Enable the Auto VoIP function globally: T3700G-52TQ(config)# auto-voip 52.2 auto-voip Description The auto-voip command is used to - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 489
Port Gigabit Stackable L3 Managed Switch CLI Guide Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet ) Example Set Auto VoIP VLAN 3 for port 3: T3700G-52TQ(config)# interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)# auto-voip 3 52.3 auto-voip - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 490
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Syntax auto-voip dscp value Parameter T3700G-52TQ(config)# interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)# auto-voip dscp 33 52.5 auto-voip untagged Description The auto-voip untagged command is used to instruct - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 491
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide 52.6 auto-voip none Description The auto-voip none command is used to instruct voice devices to send untagged packets based on settings of themselves. Syntax auto-voip none Command Mode Interface Configuration Mode ( - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 492
52-Port Gigabit Stackable L3 Managed Switch CLI Guide Example Allow packets to be sent on unauthorized Auto VoIP port 3: T3700G-52TQ(config)# interface gigabitEthernet 1/0/3 T3700G-52TQ(config-if)# auto-voip auth enable 52.8 auto-voip priority Description The auto-voip data priority command - TP-Link T3700G-52TQ | T3700G-52TQUN V1 CLI Reference Guide Guide - Page 493
T3700G-52TQ JetStream 52-Port Gigabit Stackable L3 Managed Switch CLI Guide Parameter interface--Displays the Auto VoIP configuration information of ports. When no parameter is entered, displays the global Auto VoIP configuration information. Command Mode Privileged
CLI Reference Guide
JetStream 52-Port Gigabit Stackable L3 Managed Switch
T3700G-52TQ
REV1.0.0
1910011777