TP-Link TD-8817 User Guide

TP-Link TD-8817 Manual

Get TP-Link TD-8817 PDF manuals and user guides
UPC - 845973060107
View all TP-Link TD-8817 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TD-8817 manual content summary:

  • TP-Link TD-8817 | User Guide - Page 1
    TD-8817 ADSL2/2+ Ethernet/USB Router Rev: 1.0.3 1910010148
  • TP-Link TD-8817 | User Guide - Page 2
    subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com
  • TP-Link TD-8817 | User Guide - Page 3
    . This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
  • TP-Link TD-8817 | User Guide - Page 4
    in your package: ¾ One TD-8817 ADSL2/2+ Ethernet/USB Router ¾ One AC power Adapter for TD-8817 ADSL2/2+ Ethernet/USB Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ One USB cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One Resource CD , including: z This User Guide z USB Driver z Other Helpful
  • TP-Link TD-8817 | User Guide - Page 5
    Installation Guide 6 3.1 Configure PC...6 3.2 USB Configuration ...9 3.3 Login ...11 Chapter 4. Software Configuration 14 4.1 Status ...14 4.2 Quick Start ...15 4.3 Interface Setup...15 4.3.1 Internet ...16 4.3.2 LAN...20 4.4 Advanced Setup...24 4.4.1 Firewall ...24 4.4.2 Routing ...24 4.4.3 NAT
  • TP-Link TD-8817 | User Guide - Page 6
    4.6.3 Firmware...47 4.6.4 System Restart...49 4.6.5 Diagnostic...50 4.7 Help...50 Appendix A: Specification 52
  • TP-Link TD-8817 | User Guide - Page 7
    and friendly help messages are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser. ADSL TD-8817 supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications
  • TP-Link TD-8817 | User Guide - Page 8
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide ¾ Built-in DHCP server. ¾ Built-in firewall, supports IP/MAC filter, Application filter and URL filter. ¾ Supports Virtual Server, DMZ host and IP Address Mapping. ¾ Supports Dynamic DNS, UPnP and Static Routing. ¾ Supports system log and flow
  • TP-Link TD-8817 | User Guide - Page 9
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the front panel, they indicate the device's working status. For details, please refer to LED Explanation. LED Explanation: LED Status Indication USB LAN On
  • TP-Link TD-8817 | User Guide - Page 10
    2.2 The Back Panel TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 2-2 ¾ ON/OFF: The switch for the power. ¾ POWER: The Power plug is where you will connect the power adapter. ¾ RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a
  • TP-Link TD-8817 | User Guide - Page 11
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 2-3 5
  • TP-Link TD-8817 | User Guide - Page 12
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8817 or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC's IP address. Follow the steps below to
  • TP-Link TD-8817 | User Guide - Page 13
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 7
  • TP-Link TD-8817 | User Guide - Page 14
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. ) Note: Figure 3-4 You can configure the PC to get an IP address automatically, select "Obtain an IP To continue, please type ping 192.168.1.1 on the following appeared
  • TP-Link TD-8817 | User Guide - Page 15
    192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.2 USB Configuration If you use the USB interface, First, you must install the USB's driver to the computer. You can obtain the drivers from the provided CD, or download from our website. (http://www.tp-link
  • TP-Link TD-8817 | User Guide - Page 16
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-7 Step 3: You will see Figure 3-8 as follow, please wait a moment. Figure 3-8 Step 4: After that, you will see Figure 3-9. Click Finish to complete the installation. 10
  • TP-Link TD-8817 | User Guide - Page 17
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-9 ) Note: 1) All of the above settings are under windows XP. 2) If you want to pull out the USB device you must disconnect the network of USB first. 3) In the Vista operating system, maybe the "Unknown Device" screen will pop up when you
  • TP-Link TD-8817 | User Guide - Page 18
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-10 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3-11. Click the NEXT button. Figure 3-11 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-12 Step 3: Select the connection
  • TP-Link TD-8817 | User Guide - Page 19
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-13 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click Next. Figure 3-14 Step 5: Click NEXT to finish the Quick Start. Figure 3-15 13
  • TP-Link TD-8817 | User Guide - Page 20
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 4. Software Configuration This User Guide recommends using the "Quick Installation Guide" for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you
  • TP-Link TD-8817 | User Guide - Page 21
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-2 ) Note: Click the other submenus System Log or Statistics in Figure 4-2, you will be able to view the system log and traffic statistics about the Router. 4.2 Quick Start Please refer to " 3.3: Login". 4.3 Interface Setup Choose "Interface
  • TP-Link TD-8817 | User Guide - Page 22
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 4.3.1 Internet Choose "Interface Setup→Internet" menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-4). Figure 4-4 ¾ ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path
  • TP-Link TD-8817 | User Guide - Page 23
    IP Address, you can leave it default. ¾ Bridge Interface: Activate the option, the Router can also work in Bridge mode. ¾ NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC. The NAT function can be activated or deactivated per PVC basis. ¾ Default
  • TP-Link TD-8817 | User Guide - Page 24
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide gateway to internet from this device. ¾ TCP MTU Option: Enter the TCP MTU as your desire. ¾ Dynamic Route: Select this option to specify the RIP (
  • TP-Link TD-8817 | User Guide - Page 25
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. Figure 4-7 ¾ Service name:
  • TP-Link TD-8817 | User Guide - Page 26
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide on. ¾ Static/Dynamic IP Address: For PPPoE/PPPoA connection, you need to specify the public IP address for this ADSL Router. The IP address can be either dynamically (via DHCP) or given IP address provided by your ISP. For Static IP, you need to
  • TP-Link TD-8817 | User Guide - Page 27
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-9 ¾ Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and
  • TP-Link TD-8817 | User Guide - Page 28
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP
  • TP-Link TD-8817 | User Guide - Page 29
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only,
  • TP-Link TD-8817 | User Guide - Page 30
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 4.4 Advanced Setup Choose "Advanced Setup", you can see the next submenus: Figure 4-12 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose "Advanced Setup→Firewall" menu, and you will see the next
  • TP-Link TD-8817 | User Guide - Page 31
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-14 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-15). Figure 4-15 ¾ Destination IP Address: This parameter specifies the IP network address of the final destination. ¾ IP Subnet Mask: Enter the subnet mask for
  • TP-Link TD-8817 | User Guide - Page 32
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-16 ¾ Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. ¾ NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-4) to
  • TP-Link TD-8817 | User Guide - Page 33
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Server in the next screen. The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single
  • TP-Link TD-8817 | User Guide - Page 34
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 4.4.3.3. IP Address Mapping Choose "Advanced Setup→NAT", select Multiple in Number of IPs. Click IP Address Mapping, then you can configure the Address Mapping Rule in Figure 4-20. The IP Address Mapping is for those VCs that configured with multiple
  • TP-Link TD-8817 | User Guide - Page 35
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide To add a mapping rule: Step 1: Select the "Virtual Circuit" and Multiple for the "Number of IPs". Then select the tab IP Address Mapping (shown in Figure 4-19). ) Note: IP Address Mapping is only available for VCs with Multiple IPs. Step 2: Select the
  • TP-Link TD-8817 | User Guide - Page 36
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-21 ¾ QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ). ¾ Summary: Click the button to view the configurations of QoS. ¾ Rule: Configure the rules for QoS. If the traffic complies with the rule,
  • TP-Link TD-8817 | User Guide - Page 37
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide IP Precedence Range: Enter the IP precedence range that the Router takes to differentiate the traffic. • Type of Service: Select the type of service that the Router switch port is configured with an access list specifying membership in a set of VLANs.
  • TP-Link TD-8817 | User Guide - Page 38
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-22 1. Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in Figure 4-22, you can assign the PVID for each interface in the next screen (shown in Figure 4-23). Figure 4-23 ¾ PVID: Each physical port has a default VID
  • TP-Link TD-8817 | User Guide - Page 39
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-24 ¾ ADSL Choose "Advanced Setup→ADSL", you can select the ADSL Type and ADSL Mode in the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service
  • TP-Link TD-8817 | User Guide - Page 40
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-25 ¾ ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ¾ ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose "Access Management", you can see the next submenus:
  • TP-Link TD-8817 | User Guide - Page 41
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide access to the Router. If Deactivated, all IP addresses can access to the Router. ¾ ACL Rule Index: Select the ACL rule index for the entry. ¾ Active: Enable the ACL rule. ¾ Secure IP Address: Select the IP addresses which are permitted to access to the
  • TP-Link TD-8817 | User Guide - Page 42
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-28 ¾ Filter Type Selection: Select the filter type for the configuration below. ¾ IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. ¾ Interface: Select the
  • TP-Link TD-8817 | User Guide - Page 43
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP traffic which is going out the router. ¾ IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. ) Note: You should set the IP/MAC Filter
  • TP-Link TD-8817 | User Guide - Page 44
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide ) Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the "Source IP Address", "Destination IP Address", "Subnet Mask" and "Port Number" in the corresponding field. Step 4: Select the Protocol as "TCP"
  • TP-Link TD-8817 | User Guide - Page 45
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide 4.5.2.2. MAC Filter Select IP/Mac Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-29), then you can configure the filter rules based on MAC address. Figure 4-29 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active:
  • TP-Link TD-8817 | User Guide - Page 46
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide , Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface "PVC0", and select the Direction "Outgoing" for the first rule. ) Note: If you
  • TP-Link TD-8817 | User Guide - Page 47
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-30 ¾ Filter Type Selection: Select the Application Filter for the next configuration. ¾ Application Filter: Activate or deactivate the function. ¾ ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select
  • TP-Link TD-8817 | User Guide - Page 48
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-31 ¾ Filter Type Selection: Select the URL Filter for the next configuration. ¾ Active: Select "Yes" to make the rule to take effect. ¾ URL Index: Select the index for the URL Filter entry. ¾ URL: Enter the URL for
  • TP-Link TD-8817 | User Guide - Page 49
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-32 ¾ Get Community: Set the password for the incoming Get and Get next requests from the management station. ¾ Set Community: Set the password for incoming
  • TP-Link TD-8817 | User Guide - Page 50
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide The router offers a Dynamic Domain Name System (DDNS) feature. The feature lets you use a static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User
  • TP-Link TD-8817 | User Guide - Page 51
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-35 ¾ CWMP: Select activate the CWMP function. ¾ URL: Enter the website of ACS which is provided by your ISP. ¾ User Name/Password: Enter the User Name and password to login the ACS server. ¾ Path: Enter the path that connects to the ACS server
  • TP-Link TD-8817 | User Guide - Page 52
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-37 ) Note: 1) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. 2) When you change the password, you should enter the new
  • TP-Link TD-8817 | User Guide - Page 53
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time
  • TP-Link TD-8817 | User Guide - Page 54
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-41 To upgrade the router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (www.tp-link.com). Step 2: Type the path and file name of the update file into the "New
  • TP-Link TD-8817 | User Guide - Page 55
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-42 Step 2: Save the file as the appointed file (shown in Figure 4-43). TD-8817 Figure 4-43 To restore the Router's settings restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-44). 49
  • TP-Link TD-8817 | User Guide - Page 56
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-44 4.6.5 Diagnostic Choose "Maintenance→Diagnostic", you can view the test results for the connectivity of the (shown in Figure 4-45). Figure 4-45 4.7 Help Choose "Help", you can view the help information for configuration of any function. 50
  • TP-Link TD-8817 | User Guide - Page 57
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-46 ) Note: Click the tab, and you will be able to get the corresponding information. 51
  • TP-Link TD-8817 | User Guide - Page 58
    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Appendix A: Specification General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT,CWMP Safety & Emission Ports FCC、CE 1 10/100M
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
TD-8817
ADSL2/2+ Ethernet/USB Router
Rev: 1.0.3
1910010148