TP-Link TD-W8901G Quick Installation Guide
TP-Link TD-W8901G - Wireless Router Manual
 |
UPC - 845973060046
View all TP-Link TD-W8901G manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link TD-W8901G manual content summary:
- TP-Link TD-W8901G | Quick Installation Guide - Page 1
network connections to configure the router. Power down all your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your computer to the Port labeled "1~4" on the Router with an - TP-Link TD-W8901G | Quick Installation Guide - Page 2
Router display normally as the diagram below describes. Solid light Solid light or flashing Solid light or flashing Solid light if the corresponding port To configure the device, you can either run the setup CD-ROM (method one), or run the Web based Quick Setup Wizard (method two). TP-LINK strongly - TP-Link TD-W8901G | Quick Installation Guide - Page 3
will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click START, and then follow the step-by-step instructions until you complete the configuration. The configuration has now been completed. Please skip to Step 3 "Testing the Internet Connection". 3 - TP-Link TD-W8901G | Quick Installation Guide - Page 4
Password. Enter the default values and click OK. User nameǖadmin Passwordǖadmin Click OK Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting guide and T2 will give you some help if you forget the password. The web management page will display after a successful login - TP-Link TD-W8901G | Quick Installation Guide - Page 5
/PPPoA is selected, please proceed to A; If Dynamic IP is selected, please skip to B; If Static IP is selectedLjplease skip to C; If Bridge Mode is selected, please skip to D. Click NEXT Note Bridge mode is not recommended because multiple computers are not permitted to share Internet access in this - TP-Link TD-W8901G | Quick Installation Guide - Page 6
by your ISP. Click NEXT Note If you did not get the VPI, VCI and Connection Type information, please contact your ISP for this information. B. Configuration For Dynamic IP This page will then display. Select the dynamic connection provided by your ISP. Click NEXT - TP-Link TD-W8901G | Quick Installation Guide - Page 7
. Enter the Bridge information provided by your ISP. Click NEXT After completing the above configuration, please proceed to Settings Configuration Wireless Settings Configuration This page will then display. Keep the default setting: Activated. If you want to disable Access Point, please select - TP-Link TD-W8901G | Quick Installation Guide - Page 8
it's rebooting. The basic settings for your Router are completed. Please open the web browser and log on to the following websites: http://www.tp-link.com http://www.google.com If the above websites can be accessed, it indicates that your Router has been configured successfully and you can start - TP-Link TD-W8901G | Quick Installation Guide - Page 9
T1. 2) Use the default user name and password: admin, admin. 3) Try to configure your Router once again by following the instructions in the previous steps of the QIG. T3. What can I do if I cannot access the web-based configuration page? 1) Configure your computer's IP Address. For Windows XP OS Go - TP-Link TD-W8901G | Quick Installation Guide - Page 10
Click Network Connections Right-click Local Area Connection Click Properties Double-click Internet Protocol (TCP/IP) 10 - TP-Link TD-W8901G | Quick Installation Guide - Page 11
Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK Click OK 11 - TP-Link TD-W8901G | Quick Installation Guide - Page 12
For Windows Vista OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties 12 - TP-Link TD-W8901G | Quick Installation Guide - Page 13
Double-click Internet Protocol Version 4 (TCP/IPv4). Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 13 - TP-Link TD-W8901G | Quick Installation Guide - Page 14
after the above settings have been configured. If you still cannot access the configuration page, please restore your Router's factory default settings and reconfigure your Router following the instructions of this QIG. Please feel free to contact our Technical Support if the problem persists. T4 - TP-Link TD-W8901G | Quick Installation Guide - Page 15
access the Internet, please restore your Router to its factory default settings and reconfigure your Router by following the instructions of this QIG. 4) Please feel free to contact our Technical Support if the problem still exists. Note For more details about Troubleshooting and Technical Support - TP-Link TD-W8901G | Quick Installation Guide - Page 16
Technical Support „ For more troubleshooting help, go to www.tp-link.com/support/faq.asp „ To download the latest Firmware, Driver, Utility and User Guide, go to www.tp-link.com/support/download.asp „ For all other technical support, please contact us by using the following: Global USA/Canada
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
1
Power down all your network devices, including your computer(s) and
the
Modem Router. If you currently use a modem, disconnect it now - the
Modem Router will replace your current modem.
Connect your computer to the
Port labeled “1~4” on the
Router with an Ethernet cable.
Connect the splitter to the wall
jack using a telephone line,
then use the other telephone
line to directly connect it to the
LINE port on the Router and
the MODEM port of the splitter,
also have the PHONE port of
the splitter connected to a
telephone.
If no telephone is needed, please connect the LINE port of the Router to
the wall jack using the telephone line directly.
Note
Note
Please use only wired network connections to configure the router.