TP-Link TD-W8901N TD-W8901N V1 User Guide

TP-Link TD-W8901N Manual

Get TP-Link TD-W8901N PDF manuals and user guides View all TP-Link TD-W8901N manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TD-W8901N manual content summary:

  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 1
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev: 1.0.0 1910010775
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 3
    and used in accordance with the instructions, may cause harmful interference to radio changes or modifications not expressly approved by the party responsible for compliance could void the user , this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 4
    environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed . Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 5
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 6
    TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8901N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 7
    2.1 The Front Panel 4 2.2 The Back Panel 5 2.3 Installation Environment 6 2.4 Connecting the Modem Router 7 Chapter 3. Quick Installation Guide 9 3.1 Configure PC 9 3.2 Login ...12 Chapter 4. Software Configuration 16 4.1 Status...16 4.1.1 4.1.2 4.1.3 Device Info ...16 System Log ...17
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 8
    4.5.5 4.5.6 UPnP ...63 DDNS ...64 CWMP ...65 4.6 Maintenance 66 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 Administration ...66 Time Zone ...67 Firmware ...68 SysRestart ...71 Diagnostics ...71 4.7 Help...72 Appendix A: Specifications 74 Appendix B: Troubleshooting 75 Appendix C: Technical Support 78
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 9
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package:  One TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router  One Power Adapter for TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router  Quick Installation Guide  One RJ45
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 10
    are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser. ADSL The TD-W8901N supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 11
    .  Supports firmware upgrade and Web management.  Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.  Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List). 1.3 Conventions The Router or device mentioned in this User Guide stands for TD-W8901N
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 12
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device's working status. For details, please refer to LED Explanation. LED Explanation: Name Status Indication On (
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 13
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more information. 2.2 The Back Panel Figure 2-2  POWER: The Power plug is where you
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 14
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  ADSL: Through the port, you can connect the router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4 Connecting the Modem Router.  Antenna: Used for wireless operation and data
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 15
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 2.4 Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 16
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 2-4 8
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 17
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8901N or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC's IP address. Follow the steps
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 18
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 10
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 19
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4  Note: You can configure the PC to get an IP address automatically, select "Obtain an IP address automatically" and "Obtain DNS server address
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 20
    The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.2 Login Once your host PC
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 21
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-7 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-8 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-9 Step 3: Select
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 22
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-10 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click NEXT. Figure 3-11 Step 5: Configure the rules for the WLAN, and click NEXT. 14
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 23
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-12  Note: If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 24
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4. Software Configuration This User Guide recommends using the "Quick Installation Guide" for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 25
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2  Note: Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.1.2 System Log Choose "Status→System Log" menu, and you will be able
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 26
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose "Status→
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 27
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-4  Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports.  Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames Transmit
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 28
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Select ADSL, and you port. The total errors occurred over the ADSL port when data is being transmitted. The total PDUs transmitted over the ADSL port. The total errors occurred over the ADSL port Quick Start Please refer to 3.2 Login. 20
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 29
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.3 Interface Setup Choose "Interface Setup", you can see the next submenus: Internet, LAN and Wireless. Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Choose "Interface Setup→
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 30
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-6  ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations,
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 31
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7.  Status: If you want to use a designed VC, you should activate it.  VPI: Identifies the virtual path between endpoints in an ATM network.
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 32
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default.  NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC. The NAT function can be activated
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 33
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-8  Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format.
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 34
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-9  Servicename: Enter a name to mark current connection, or you can leave it blank.  Username: Enter your username for your PPPoA/PPPoE connection.  Password: Enter your password for your PPPoA/PPPoE connection.  Encapsulation:
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 35
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide automatically. And once there is traffic send or receive, the connection will be automatically on.  Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public IP address for this ADSL Router. The IP address can
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 36
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-11  Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 37
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports both IGMP version 1 (IGMP v1), IGMP
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 38
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide be able to obtain IP address automatically although the DHCP function is enabled. All the ports are checked by default.  DHCP Table: The information of the DHCP clients will be displayed here  Hostname: Display the name of the DHCP client
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 39
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-13  DHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN side.  Note: If you select Disabled, the DHCP function will not take effect. 4.3.3 Wireless Choose "Interface Setup→Wireless" menu, and you will see
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 40
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-14 32
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 41
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network.  Access point: Select Activated to allow
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 42
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  11n Settings: These are the settings of the 11n parameters. If "802.11n", "802.11g+n" or "802.11b+g+n" is selected for Wireless mode, these settings will be displayed.  Channel Bandwidth: Select the Bandwidth you want to use from the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 43
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 1) WEP-64Bits To configure WEP-64Bits settings, select the WEP-64Bits option from the drop-down list. The menu will change to offer the appropriate settings. WEP-64Bits is a data privacy mechanism based on a 64-bit shared key algorithm, as
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 44
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-18  Encryption: Select the encryption you want 64 Hexadecimal digits. 4) WPA2-PSK To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA2-PSK
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 45
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.3.3.1 WPS Settings Figure 4-20  WPS Settings: WPS can help you to add a new wireless device to an existing network quickly. This section will guide you how to use WPS function.  WPS state: Display the current WPS state.  WPS mode:
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 46
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Click Start WPS button in Figure 4-21. Step 2: For the configuration of the wireless adapter, please choose "Push the button on my access point" in the configuration
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 47
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 2) PIN code If the wireless adapter supports Wi-Fi Protected Setup and the PIN method,
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 48
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Step 2: For the Router, keep PIN code selected and enter the PIN code of the wireless adapter in the field after enrollee PIN code as shown below. Then click
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 49
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Note: The WPS Configuration Screen of Wireless Adapter The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 4-23.  SSID: Wireless network name shared among all points in a wireless
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 50
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  MAC Address: Enter the MAC Address you wish to filter in the field.  Note: For most users, it is recommended to use the default Wireless LAN Performance settings. Any changes made to these settings may adversely affect your wireless
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 51
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.2 Routing Choose "Advanced Setup→Routing" menu, and you will see the routing information in the next screen (shown in Figure 4-26). Figure 4-26 Click ADD ROUTE button to add a
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 52
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3 NAT Choose "Advanced Setup→NAT" menu, you can setup the NAT (Network Address Translation) function for the Router (shown in Figure 4-28).  Note: To use the NAT function, the Virtual Circuit should not be configured to Bridge mode.
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 53
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-29  DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. 4.4.3.2 Virtual Server Choose "Advanced Setup→NAT→Virtual Server" in Figure 4-28, you can configure the Virtual Server in the next screen. The
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 54
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Virtual Server Listing: This displays the information about the Virtual Servers you establish. To add a virtual server entry: Step 1: Select the "Virtual Circuit" and select "Virtual Server".  Note: For VCs with single IP, select Single;
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 55
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Rule Typ: There are four types: one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload.  Local Start & End IP: Enter the local IP Address you plan to map to. Local Start IP is the starting local IP address and Local
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 56
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-32  QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ).  Summary: Click the button to view the configurations of QoS.  Rule: Configure the rules for QoS. If the traffic complies
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 57
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Application: Select the application that the rule aimed at.  Physical Ports: Select the port whose traffic flow are controlled by the rule.  Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 58
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.5 VLAN Choose "Advanced Setup→VLAN", you can activate the VLAN function in the next screen. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 59
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-34  PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. 2) Define VLAN Group Click Define VLAN Group in
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 60
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-35  VLAN Index: Setup→ADSL", you can select the ADSL Type and ADSL Mode in the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 61
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36  ADSL Mode: Select the ADSL operation mode which your ADSL connection uses.  ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose "Access Management", you can see the next
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 62
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-38  ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router.  ACL Rule Index: Select the ACL rule index for the entry.
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 63
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.1 IP Filter Select IP/MAC Filter as the Filter type, and select IP as the Rule type (shown in Figure 4-39), then you can configure the filter rules based on IP address. The filtering includes Outgoing and Incoming, the detailed
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 64
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address). If select LAN as an interface, the filter will match the IP traffic of LAN port
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 65
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1), (1, 2) and (1, 3). Step 1: Select the "IP/MAC Filter" as the Filter Type Selection (show in Figure 4-39). Select the "IP" as the Rule Type on
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 66
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12.  Note: After
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 67
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-40  Rule Type: Select MAC for the MAC Filter rule.  Active: Select "Yes" to make the rule to take effect.  MAC Address: Enter the MAC address for the rule.  Rule Unmatched: If the current rule can not match, and you select
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 68
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Select the "MAC" as the Rule Type on the Filter screen (show in Figure 4-40). , Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 69
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.3 Application Filter Select Application Filter as the Filter type (shown in Figure 4-41), and then you can configure the filter rules based on application. Figure 4-41  Filter Type Selection: Select the Application Filter for the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 70
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-42  Filter Type Selection: Select the URL Filter for the next configuration.  add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com. Presume the rule is aimed at the interface
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 71
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Other operations for the entries as shown in Figure 4-39: Select the URL Index to view or modify the entry. Select the URL Index to locate the specific rule, and then click the DELETE button to delete the entry. 4.5.3 SNMP Choose "Access
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 72
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-44  UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the UPnP take effect.  Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 73
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Service Provider: This field displays the service provider of DDNS.  My Host Name: Enter your host name here.  E-mail Address: Enter your E-mail address here.  Username & Password: Type the "User Name" and "Password" for your DDNS
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 74
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide  User Name/Password: Enter the User Name and Password that provided the ACS server to login the router.  Periodic Inform: Activate or deactivate the function. If Activated, the information will be informed to ACS server periodically. 
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 75
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.6.2 Time Zone Choose "Maintenance→Time Zone", you can configure the system time in the screen (shown in Figure 4-49). The system time is the time used by the device for scheduling services. There are three methods to configure the time.
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 76
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-50 3) Manually Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time. Figure 4-51 4.6.3 Firmware Choose "Maintenance→Firmware", you can upgrade the firmware of the Router in
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 77
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-52 To upgrade the router's firmware, follow these instructions below: Step 1: Type the path and file name of the update file into the "New Firmware Location" field. Or click the Browse button to locate the update file. Step 2:
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 78
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-53 Step 2: Save the file as the appointed file (shown in Figure 4-54). TD-W8901N Figure 4-54 To restore the Router's settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in "
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 79
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.6.4 SysRestart Choose "Maintenance→SysRestart", you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-55). Figure 4-55 4.6.5 Diagnostics Choose "Maintenance→
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 80
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-56 4.7 Help Choose "Help", you can view the help information for configuration of any function. 72
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 81
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-57  Note: Click the tab, and you will be able to get the corresponding information. 73
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 82
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specifications General Standards and Protocols Safety & Emission Ports ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA, PPPoE,
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 83
    refer to T1. 2) Use the default user name and password: admin, admin. 3) Try to configure your modem router once again by following the instructions in 3.2 Login. T3. What can I do if I cannot access the web-based configuration page? 1) Configure your computer's IP Address. For Mac OS X  Click the
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 84
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide For Windows XP  Click "Start -> Control Panel -> Network and Internet Connections -> Network Connections".  Right-click Wireless Network Connection (or Local Area Connection), and then click Properties.  Select Internet Protocol (TCP/IP
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 85
    your modem router by following the instructions in 3.2 Login. 5) Please feel free to contact our Technical Support if the problem still exists.  Note: For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link
  • TP-Link TD-W8901N | TD-W8901N V1 User Guide - Page 86
    TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support  For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq  To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
TD-W8901N
150Mbps
Wireless N ADSL2+ Modem Router
Rev: 1.0.0
1910010775