TP-Link TD-W9977 User Guide

TP-Link TD-W9977 Manual

Get TP-Link TD-W9977 PDF manuals and user guides View all TP-Link TD-W9977 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TD-W9977 manual content summary:

  • TP-Link TD-W9977 | User Guide - Page 1
    User Guide N300 Wireless Gigabit VDSL/ADSL Modem Router TD-W9977 REV1.0.0 1910011880
  • TP-Link TD-W9977 | User Guide - Page 2
    Appearance 3 Chapter 2. Connect the Hardware 6 2. 1. Position Your Modem Router 7 2. 2. Connect Your Modem Router 7 Chapter 3. Log in to Your Modem Router 9 Chapter 4. Set Up Internet Connections 11 4. 1. Use Quick Setup Wizard 12 4. 2. Manually Set Up an Internet Connection 12 4. 3. Test
  • TP-Link TD-W9977 | User Guide - Page 3
    Modem Router Service Account 53 11. 5. Interface Grouping 53 11. 6. Create Static Routes 55 11. 7. Set up a VPN Service-6to4 61 11. 8. 2.Specify the 6rd Tunnel with Parameters Provided by Your ISP 62 Chapter 12. Administrate Your Network 63 12. 1. Set System Time 64 12. 2. Update the Firmware
  • TP-Link TD-W9977 | User Guide - Page 4
    from Download Center at http://www.tp-link.com/support. • The Quick Installation Guide (QIG) can be found where you find this guide or inside the package of the router. • Specifications can be found on the product page at http://www.tp-link.com. • A Technical Support Forum is provided for you to
  • TP-Link TD-W9977 | User Guide - Page 5
    Chapter 1 Get to Know Your Modem Router This chapter introduces the modem router and shows its appearance. It contains the following sections: • Product Overview • Product Appearance
  • TP-Link TD-W9977 | User Guide - Page 6
    Product Overview TP-Link's Modem Router is a combined wired/wireless network connection device with integrated wireless router and DSL modem, reducing hassle of configuration and saving space. With DSL and EWAN ports, the modem router is compatible with DSL connections and fiber/cable access. With
  • TP-Link TD-W9977 | User Guide - Page 7
    firmware upgrading is in process. Do not disconnect or power off the modem router. Power is off. Please ensure that the power adapter is connected correctly. DSL synchronization is established. DSL synchronization is in progress. DSL synchronization failed. Please refer to Note 1 for troubleshooting
  • TP-Link TD-W9977 | User Guide - Page 8
    The back panel provides buttons, connection ports, and antennas. Refer to the following for detailed instructions. Item Description DSL Port For connecting the modem router to the Internet. Connect the port to the splitter or directly connect the port to the phone jack via a phone cable. For
  • TP-Link TD-W9977 | User Guide - Page 9
    Chapter 2 Connect the Hardware This chapter contains the following sections: • Position Your Modem Router • Connect Your Modem Router
  • TP-Link TD-W9977 | User Guide - Page 10
    modem router. Many obstacles may limit the range of the wireless signal, for example, concrete structures or thick walls. For your safety and best Wi-Fi performance, please: • Do Not locate the modem router accessible. If you don't need the phone service, just directly connect the modem router to
  • TP-Link TD-W9977 | User Guide - Page 11
    2: Wireless Connect wirelessly by using the default SSID (Wireless Network Name) and Wireless Password printed on the product label of the modem router. Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets, most USB network cards, can be connected to your
  • TP-Link TD-W9977 | User Guide - Page 12
    Chapter 3 Log in to Your Modem Router
  • TP-Link TD-W9977 | User Guide - Page 13
    modem router. 1. If the TCP/IP Protocol on your computer is set to the static (fixed) IP address, you need to change it to obtain an IP address automatically. Refer to Appendix: Troubleshooting click Log in. Note: For subsequent logins, you only need to enter the password that you have created. 10
  • TP-Link TD-W9977 | User Guide - Page 14
    Internet. The modem router is equipped with a web-based Quick Setup wizard. It has many ISP information built in, automates many of the steps and verifies that those steps have been successfully completed. Furthermore, you can also set up an IPv6 connection if your ISP provides IPv6 service. This
  • TP-Link TD-W9977 | User Guide - Page 15
    , and log in with the password you set for the modem router. 2. Select your Region and Time Zone, then click Next. 3. Follow the step-by-step instructions of the Quick Setup to complete the initial configuration. Note: During the quick setup process, you can change the preset wireless network name
  • TP-Link TD-W9977 | User Guide - Page 16
    to set up an IPv6 connection: 1. Make sure you have set up an IPv4 connection by using Quick Setup wizard or manually before setting up an IPv6 connection. 2. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 3. Go to Advanced > Network > Internet page. 13
  • TP-Link TD-W9977 | User Guide - Page 17
    Click OK to make the settings effective. Now IPv6 service is available for your network. 4. 5. Wireless Router Mode The modem router supports two operation modes: DSL Modem Router Mode and Wireless Router mode. The modem router uses the DSL Modem Router Mode by default, but you can change the mode
  • TP-Link TD-W9977 | User Guide - Page 18
    Connections 2. Connect your computer to the modem router. For details, refer to Connect Your Modem Router. 3. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 4. Go to Advanced > Operation Mode, select the Wireless Router Mode, and click Save. 5. Go to
  • TP-Link TD-W9977 | User Guide - Page 19
    Chapter 5 Bandwidth Control The Bandwidth Control feature is used to fully utilize your limited bandwidth and optimize the load respectively. With this feature enabled, you can assign a specific minimum or maximum bandwidth for each computer, thus minimizing the impact caused by heavy load.
  • TP-Link TD-W9977 | User Guide - Page 20
    the bandwidth control feature, you'd better set static IP Address on each computer to be controlled or configure Address reservation on the modem router in order to manage it easily. About how to configure address reservation, please refer to Reserve LAN IP Addresses. 1. Visit http://tplinkmodem
  • TP-Link TD-W9977 | User Guide - Page 21
    with this IP address will get independent given bandwidth. When you configure the IP address range, all computers in the range will share the given bandwidth. 2 ) Port Range: Keep the default settings. The default port range of TCP protocol or UDP protocol is from 1 to 65535. 3 ) Protocol: Keep the
  • TP-Link TD-W9977 | User Guide - Page 22
    Chapter 5 Bandwidth Control Done! Now you and your roommate have an independent bandwidth. 19
  • TP-Link TD-W9977 | User Guide - Page 23
    6 Network Security This chapter guides you on how to protect your home network from unauthorized users by implementing these three network security functions. You can block or allow specific client devices to access your wireless network using MAC Filtering, or using Access Control for wired and
  • TP-Link TD-W9977 | User Guide - Page 24
    the wireless network. • The unknown device is not allowed to access the wireless network. • I don't have to keep changing my wireless password as often. 1. Visit http://tplinkmodem.net, and log in with the password you set for the router. 2. Go to Advanced > Wireless > MAC Filtering and enable
  • TP-Link TD-W9977 | User Guide - Page 25
    access from the devices in the list below or Allow wireless access only from the devices in the list below and click Save. 2 ) Click Add. Done! 3 ) Enter the MAC Address manually Access Control Access Control is used to block or allow specific client devices to access to access my network (via
  • TP-Link TD-W9977 | User Guide - Page 26
    Chapter 6 Network Security 3. Select the access mode to either block (recommended) or allow the device(s) in the list. To block specific device(s) 1 ) Select Blacklist and click Save. 2 ) Select the device(s) to
  • TP-Link TD-W9977 | User Guide - Page 27
    address. This will prevent ARP spoofing and other ARP attacks by denying network access to a device with matching IP address in the Binding list, but 1. Visit http://tplinkmodem.net, and log in with the password you set for the router. 2. Go to Advanced > Security > IP & MAC Binding and enable IP
  • TP-Link TD-W9977 | User Guide - Page 28
    Chapter 6 1 ) Click Add. Network Security Done! 2 ) Enter the MAC address and IP address that you want to bind. 3 ) Select the check box to enable the entry and click OK. Now you don't need to worry about ARP spoofing and ARP attacks. 25
  • TP-Link TD-W9977 | User Guide - Page 29
    Chapter 7 IPTV IPTV is the abbreviation of Internet Protocol Television. The service can only be delivered through the Internet, and our modem router provides a specific LAN port for IPTV. By automatically separating IPTV from Internet surfing, we guarantee you a high quality of video streaming and
  • TP-Link TD-W9977 | User Guide - Page 30
    ADSL, fill in PVC parameters (VPI and VCI). VLAN ID and PVC parameters are all provided by your IPTV service provider. 7. Click Save to make the settings effective. Configurations needed on modem router is done now! You may need other configurations on your set-top box before enjoying your TV. 27
  • TP-Link TD-W9977 | User Guide - Page 31
    Chapter 8 Parental Controls This function allows you to block inappropriate, explicit and malicious websites, and control access to specified websites at specified time.
  • TP-Link TD-W9977 | User Guide - Page 32
    the Internet and even types of websites they can visit. For example, I want to allow my children's devices (e.g. a computer or a tablet) to access only www.tp-link.com and Wikipedia.org from 18:00 (6PM) to 22:00 (10PM) on weekdays and not other time. 1. Visit http://tplinkmodem.net, and log in
  • TP-Link TD-W9977 | User Guide - Page 33
    the device to be controlled. Or, enter the Device Name and MAC Address manually. 5. Click the icon to set the Effective Time. Drag the cursor over mode. 1 ) With Blacklist selected, the controlled devices cannot access any websites containing the specified keywords during the Effective Time period.
  • TP-Link TD-W9977 | User Guide - Page 34
    200 keywords for both Blacklist and Whitelist. Below are some sample entries to allow access. 1 ) Enter a web address (e.g. www.tp-link.com) or a web address keyword (e.g. wikipedia) to only allow or block access to the websites containing that keyword. 2 ) If you wish to block all Internet browsing
  • TP-Link TD-W9977 | User Guide - Page 35
    Chapter 9 Guest Network This function allows you to provide Wi-Fi access for guests without disclosing your main network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In
  • TP-Link TD-W9977 | User Guide - Page 36
    the modem router. 2. Go to Advanced > Guest Network. Locate the Wireless section. 3. Create a 2.4GHz guest network. 1 ) Enable 2.4GHz guest network. 2 ) Set an easy-to-identify SSID. Don't select Hide SSID unless you want your guests and other people to manually input this SSID for Wi-Fi access
  • TP-Link TD-W9977 | User Guide - Page 37
    bandwidth according to your needs. Note: Some modem routers may not offer some of these guest network options. • Allow guests to see each other Select this check box to allow the clients in your guest network to access each other. • Allow guests to access my local network Select this check box to
  • TP-Link TD-W9977 | User Guide - Page 38
    the problem that external host cannot initiatively communicate with the specified device in the local network. With forwarding feature the modem router can in the local network, thus to realize some special functions. TP-Link modem router includes four forwarding rules. If two or more rules are set
  • TP-Link TD-W9977 | User Guide - Page 39
    service uses different service port. Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port 110 in POP3 service. Please verify the service PC is connected to the modem router with the WAN IP address 218.18.232.154. Personal Website Modem Router How can I do that?
  • TP-Link TD-W9977 | User Guide - Page 40
    you want to use is not in the Service Type, you can enter the corresponding parameters manually. You should verify the port number that the service needs. 3. You can add multiple virtual server rules if you want to provide several services in a modem router. Please note that the External Port cannot
  • TP-Link TD-W9977 | User Guide - Page 41
    ://tplinkmodem.net, and log in with the password you set for the modem router. 2. Go to Advanced > NAT Forwarding > Port Triggering and click not listed in the Existing Applications list, please enter the parameters manually. You should verify the external ports the application uses first and
  • TP-Link TD-W9977 | User Guide - Page 42
    can login normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ with all ports opened. 1. Assign a static IP address to your PC, for example 192.168.1.100. 2. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 3. Go
  • TP-Link TD-W9977 | User Guide - Page 43
    conference) or remote assistance, etc. Tips: 1. UPnP is enabled by default in this modem router. 2. Only the application supporting UPnP protocol can use this feature. 3. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of operating system need
  • TP-Link TD-W9977 | User Guide - Page 44
    the basic configuration of the modem router using the web management page. This chapter contains the following sections: • LAN Settings • IPv6 LAN Settings • Wireless Settings • Set Up a Dynamic DNS Service Account • Interface Grouping • Create Static Routes • Set up a VPN Connection • Set Up the
  • TP-Link TD-W9977 | User Guide - Page 45
    network from receiving traffic for a multicast group they have not explicitly joined. 6. You can configure the modem router's Second IP and Subnet Mask for LAN interface through which you can also access the web management page. 7. Leave the rest of the default settings as they are. 8. Click Save
  • TP-Link TD-W9977 | User Guide - Page 46
    Server. 4. Specify the IP Address Pool, the start address and end address must be on the same subnet with LAN IP. The modem router will assign addresses within this specified range to its clients. It is from 192.168.1.100 to 192.168.1.199 by default. 5. Enter a value for the Address Lease Time
  • TP-Link TD-W9977 | User Guide - Page 47
    accesses the DHCP server. If there are some devices in the LAN that require permanent IP addresses, please configure Address Reservation on the router http://tplinkmodem.net, and log in with the password you set for the modem router. 2. Go to Advanced > Network > LAN Settings page and select IPv4.
  • TP-Link TD-W9977 | User Guide - Page 48
    to make the modem router assign IPv6 address prefixes to hosts. Note: Do not select the Enable RDNSS and Enable ULA Prefix check boxes unless required by your ISP. Otherwise you may not be able to access the IPv6 network. For more information about RDNSS and ULA Prefix, contact our technical support
  • TP-Link TD-W9977 | User Guide - Page 49
    IPv6 addresses to hosts. 2 ) Specify the Start/End IPv6 Address for the IPv6 suffixes. The modem router will generate IPv6 addresses within the specified range. 3 ) Keep Leased Time as the default value. 4 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a specific
  • TP-Link TD-W9977 | User Guide - Page 50
    you need to manually join the modem router. Channel: Select the channel you want to use from the drop-down list. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point
  • TP-Link TD-W9977 | User Guide - Page 51
    Connection You can use WPS (Wi-Fi Protected Setup) feature to add a new wireless device to your existing network quickly. Method 1 Use the WPS Button Use this method if your client device has a WPS button. 1. Press the WPS button the modem router for 1 second. 2. Press the WPS button of the
  • TP-Link TD-W9977 | User Guide - Page 52
    for about two minutes during the WPS process. 6. When the WPS LED is on, the client device has successfully connected to the modem router. Note: 1. The WPS LED on the modem router will light on for five minutes if the device has been successfully added to the network. 2. The WPS function cannot be
  • TP-Link TD-W9977 | User Guide - Page 53
    The selected time will be in red. Note: 1. Make sure that the time of the router is correct before using this function. For details, refer to Set System Time. 2. If you net, and log in with the password you set for the modem router. 2. Go to Advanced > Status page. You can see the Wireless box. 50
  • TP-Link TD-W9977 | User Guide - Page 54
    detailed information of the connected wireless clients: 1. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2. Go to Advanced > Wireless > Statistics page. 3. You can view the detailed information of the wireless clients, including its connected wireless
  • TP-Link TD-W9977 | User Guide - Page 55
    devices on your network from interacting with each other, but still able to access the Internet. AP isolation is disabled by default. • WDS Bridging: Select this check box to enable the WDS (Wireless Distribution System) Bridging feature to allow the router to bridge with another access point 52
  • TP-Link TD-W9977 | User Guide - Page 56
    area network (WLAN). Refer to Appendix: Troubleshooting for detailed instructions. 11. 4. Set Up a Dynamic DNS Service Account Most ISPs (Internet service providers) assign a dynamic IP address to the router and you can use this IP address to access your router remotely. However, the IP address can
  • TP-Link TD-W9977 | User Guide - Page 57
    for entertainment. I want to isolate working devices from others while keep all devices' access to the Internet. 1. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2. Go to Advanced > Network > Interface Grouping to open the configuration page where some
  • TP-Link TD-W9977 | User Guide - Page 58
    travel to reach a specific host or network. Data from one point to another will always follow the same path regardless of other my company's network at the same time, I need to configure the static routing. Modem router Router 2 Company's server LAN: 192.168.1.1 WAN: 172.30.30.100 LAN: 192.168
  • TP-Link TD-W9977 | User Guide - Page 59
    IP address cannot be on the same subnet with the WAN IP or LAN IP of the router. In the example, the IP address of the company network is the destination IP address, so This IP address must be on the same subnet with the router's IP which sends out the data. In the example, the data packets will be sent
  • TP-Link TD-W9977 | User Guide - Page 60
    and resources, and vice versa. I know that the modem router in my office and the device in headquarter both support IPSec VPN feature, so I decide to set up a VPN connection with the headquarter office. The following diagram is a typical VPN topology. Here Site A refers to regional office's network
  • TP-Link TD-W9977 | User Guide - Page 61
    network)'s LAN IP and WAN IP. 2. Configuration on site A (local network). 1 ) Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2 ) Go to Advanced > Network > IPSec VPN to open the configuration page. Click Add to set up
  • TP-Link TD-W9977 | User Guide - Page 62
    addresses column, here we take Subnet Address as an example. Then input the LAN IP range of Site A in the IP Address for VPN column, and input Subnet Mask of Site A. 6 ) Configure Site B's LAN. In the Tunnel access from local IP addresses column, here we take Subnet Address as an example. Then input
  • TP-Link TD-W9977 | User Guide - Page 63
    sure that Site A and Site B use the same pre-shared keys and Perfect Forward Secrecy settings. 4. The Status column will change to UP if the VPN connection has been set up successfully. 5. Check the VPN connection. You can ping site B' LAN IP from your computer in site A to verify that the IPSec
  • TP-Link TD-W9977 | User Guide - Page 64
    for networks that do not support native dual-stack, where both IPv6 and IPv4 run independently. The modem router provides three tunneling mechanisms: 6to4, 6rd and DS-Lite. The way to set up 6rd and DS-Lite tunnel are similar. 11. 8. 1. Use the Public IPv6 Tunnel Service-6to4 The 6to4 tunnel is
  • TP-Link TD-W9977 | User Guide - Page 65
    . Note: Still not being able to access IPv6 resources means that not any 6to4 public tunnel service provider. 1. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2. ISP, choose Auto or Manual. More parameters are needed if you choose Manual. 5. Click Save.
  • TP-Link TD-W9977 | User Guide - Page 66
    Network This chapter introduces how to change the system settings and administrate your modem router's network. This chapter contains the following sections: • Set System Time • Update the Firmware • Back up and Restore Configuration Settings • Change the Administrator Account • Local Management
  • TP-Link TD-W9977 | User Guide - Page 67
    the following methods: Manually: Select your time zone and enter your local time. Get from PC: Click this button if you want to use the current managing PC's time. Get GMT: Click this button if you want to get time from the Internet. Make sure your modem router can access the Internet before you
  • TP-Link TD-W9977 | User Guide - Page 68
    at TP-Link official website, you can download the latest firmware file from our website: www.tp-link.com and upgrade the firmware to the latest version. Follow the steps below to update your firmware to the latest. 1. Download the latest firmware file for the router from our website www.tp-link.com
  • TP-Link TD-W9977 | User Guide - Page 69
    you back up the current configuration settings before resetting the modem router. 12. 4. Change the Administrator Account Admin account is used to log in to the modem router's web management page. You are required to set the admin account at first login. You can also change it on the web page
  • TP-Link TD-W9977 | User Guide - Page 70
    . Follow the steps below to specify the local management. 1. Visit http://tplinkmodem.net, and log in with the password you set for the modem router. 2. Go to Advanced > System Tools> Administration page. Locate the Local Management section. 3. Keep the Port as the default setting. Enter the IP
  • TP-Link TD-W9977 | User Guide - Page 71
    can help you know what happened to your modem router, facilitating you to locate the malfunctions. For example when your modem router does not work properly, you will need to save the system log and send it to the technical support for troubleshooting. 1. Visit http://tplinkmodem.net, and log in
  • TP-Link TD-W9977 | User Guide - Page 72
    to your computer. Click Log Settings to set the storage path of logs. • Save Locally: Select this option to cache the system log to the router's local memory, select the minimum level of system log to be saved from the drop-down list. The logs will be shown in the table
  • TP-Link TD-W9977 | User Guide - Page 73
    the traffic statistics in Traffic Statistics List section. This function is disabled by default. 12. 9. CWMP Settings The modem router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto
  • TP-Link TD-W9977 | User Guide - Page 74
    checkbox to enable authentication for the connection request. • Connection Request Username/Password: Enter the username/password for the ACS server to log in to the router. 71
  • TP-Link TD-W9977 | User Guide - Page 75
    connects to the ACS server. • Get RPC methods: Click to get the methods to support CWMP. Click Save to make the settings effective. 12. 10. SNMP Settings SNMP ( generating. An SNMP Agent is an application running on the modem router that performs the operational role of receiving and processing SNMP
  • TP-Link TD-W9977 | User Guide - Page 76
    Read-only Community: Displays the default public community string that protects the router from unauthorized access. • Write Community: Displays the default write community string that protects the router from unauthorized changes. • System Name: Displays the administratively-assigned name for this
  • TP-Link TD-W9977 | User Guide - Page 77
    : Troubleshooting T1. How do I restore my modem router's configuration to its factory default settings? There are two ways to reset the modem router: For details, refer to the instructions in To reset the modem router to factory default settings. Note: Once the modem router is reset, the current
  • TP-Link TD-W9977 | User Guide - Page 78
    4 ) Click LAN settings, deselect the following three options and click OK; 5 ) Go to Advanced > Restore advanced settings, click OK to save the settings. 75
  • TP-Link TD-W9977 | User Guide - Page 79
    factory default settings. Note: You'll need to reconfigure the modem router to surf the Internet once the modem router is reset. Open a web browser and log in again. If login fails, please contact the technical support. T4. What can I do if I cannot access the Internet? 1. Check to see if all the
  • TP-Link TD-W9977 | User Guide - Page 80
    modem router by following the instructions in Use Quick Setup Wizard. 6. Please contact our Technical Support if the problem still exists. T5. How to configure MAC Clone? You can manually change the MAC address of the modem router. It is helpful when your Internet access wireless adapter driver is
  • TP-Link TD-W9977 | User Guide - Page 81
    other wireless network except your own, follow the steps below: 1. Check the Wi-Fi LED indicator on your wireless router/modem; 2. Make sure your computer/device is still in the range of your router/modem, move closer if it is currently too far away; 3. Go to Basic > Wireless page, and check the
  • TP-Link TD-W9977 | User Guide - Page 82
    it is suggested to confirm the wireless password on your modem router. Note: Wireless password/Network Security Key is case sensitive router closer and try again; 2 ) Change the wireless Channel of the router to 1,6,or 11 to reduce interference from other networks; 3 ) Re-install or update the driver
  • TP-Link TD-W9977 | User Guide - Page 83
    Sharing Center > Change adapter settings. 2 ) Right-click your network connection (wired or wireless) and select Properties. 3 ) Double-click Internet Protocol Version 4 (TCP/IPv4). 4 ) Select both Obtain an IP address automatically and Obtain DNS server address automatically, then click OK. 5 )
  • TP-Link TD-W9977 | User Guide - Page 84
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link TD-W9977 | User Guide - Page 85
    the risk of electric shock and voiding the limited warranty. If you need service, please contact us. • Avoid water and wet locations. • Adapter shall be installed near the equipment and shall be easily accessible. • The plug considered as disconnect device of adapter. Use only power supplies which
  • TP-Link TD-W9977 | User Guide - Page 86
    Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
REV1.0.0
1910011880
N300 Wireless Gigabit VDSL/ADSL Modem Router
TD-W9977
User Guide