TP-Link TD-W9980 User Guide

TP-Link TD-W9980 Manual

Get TP-Link TD-W9980 PDF manuals and user guides View all TP-Link TD-W9980 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TD-W9980 manual content summary:

  • TP-Link TD-W9980 | User Guide - Page 1
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router Rev: 1.0.0 1910010923
  • TP-Link TD-W9980 | User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link TD-W9980 | User Guide - Page 3
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • TP-Link TD-W9980 | User Guide - Page 4
    Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented Russian Federation None This subsection does not apply for the geographical area within a radius
  • TP-Link TD-W9980 | User Guide - Page 5
    Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-
  • TP-Link TD-W9980 | User Guide - Page 6
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link TD-W9980 | User Guide - Page 7
    : Product Description: N600 Wireless Dual Band Gigabit VDSL2 Modem Router Model No.: TD-W9980 Trademark: TP-LINK We declare under conformity with the following standards or other normative documents EN 300 328 V1.7.1: 2006 EN 301 489-1 V1.9.2:2011& EN 301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024
  • TP-Link TD-W9980 | User Guide - Page 8
    2.3 Connecting the Modem Router 8 Chapter 3. Quick Installation Guide 9 3.1 TCP/IP Configuration...9 3.2 Quick Installation Guide 10 Chapter 4. Configuring the Modem Router 16 4.1 Login ...16 4.2 Status...16 4.3 Quick Setup ...17 4.4 Operation Mode ...18 4.5 Network...18 4.5.1 WAN Settings...19
  • TP-Link TD-W9980 | User Guide - Page 9
    ...70 4.11.3 Storage Sharing...71 4.11.4 FTP Server ...73 4.11.5 Media Server ...74 4.11.6 Print Server...75 4.12 Route Settings ...76 4.12.1 Default Gateway ...76 4.12.2 Static Route ...76 4.12.3 IPv6 Static Route ...77 4.12.4 RIP Settings...78 4.13 Forwarding...79 4.13.1 Virtual Servers ...79 4.13
  • TP-Link TD-W9980 | User Guide - Page 10
    .3 Manage Control ...102 4.22.4 CWMP Settings ...103 4.22.5 SNMP Settings ...104 4.22.6 Backup & Restore...104 4.22.7 Factory Defaults...105 4.22.8 Firmware Upgrade...105 4.22.9 Reboot ...106 4.22.10 Statistics...107 4.23 Logout...108 Appendix A: Specifications 109 Appendix B: Troubleshooting 110
  • TP-Link TD-W9980 | User Guide - Page 11
    The following contents should be found in your package:  One TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router  One Power Adapter for TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router  Quick Installation Guide  One RJ45 cable  Two RJ11 cables  One VDSL splitter  One
  • TP-Link TD-W9980 | User Guide - Page 12
    protections, the TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router provides complete data privacy. The modem router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server
  • TP-Link TD-W9980 | User Guide - Page 13
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide technology.  Supports bridge mode and Router Access Control List).  Supports USB Storage Sharing, Print Server, FTP Server, Media Server.  Supports Ethernet WAN (EWAN).  Supports Bandwidth Control.  Supports IPv6.  Supports
  • TP-Link TD-W9980 | User Guide - Page 14
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router's LEDs are located on the front panel (View from left to right). They indicate the device's
  • TP-Link TD-W9980 | User Guide - Page 15
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide (Wireless 2.4GHz) Flash Off Wireless is have already made a right connection, please contact your ISP to make sure if your Internet service is available now. 2. If the Internet LED is off, please check your DSL LED first
  • TP-Link TD-W9980 | User Guide - Page 16
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide : There are two ways to reset the modem router's factory defaults. Method one: With the modem router powered on, use a or the other Ethernet network devices. In wireless router mode you will be able to connect to Cable/FTTH/VDSL
  • TP-Link TD-W9980 | User Guide - Page 17
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ethernet).  PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.  TCP/IP protocol on each
  • TP-Link TD-W9980 | User Guide - Page 18
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Note: The diameter of the screw, 3. Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut
  • TP-Link TD-W9980 | User Guide - Page 19
    Installation Guide This chapter will show you how to configure the basic functions of your TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem
  • TP-Link TD-W9980 | User Guide - Page 20
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide You can check it following the steps below: 1) Is the connection between your PC and the modem router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP
  • TP-Link TD-W9980 | User Guide - Page 21
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 3-5 3. Select your Region and Time Zone from the drop-down list, then click Next. Figure 3-6 4. The modem router supports two modes: xDSL Modem Router Mode and Wireless Router Mode. Choose your desired mode and then click
  • TP-Link TD-W9980 | User Guide - Page 22
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Wireless Router Mode: In this mode, the device enables multi-users to share Internet via Ethernet WAN (EWAN) using its interchangeable LAN/WAN port and share it wirelessly at 300Mbps wireless
  • TP-Link TD-W9980 | User Guide - Page 23
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 3-9 3) Here we use PPPoE as an example. Enter the PPPoE Username and Password provided by your ISP. After confirming the password, click Next to continue. Figure 3-10  Wireless Router Mode 1) Select the connection type
  • TP-Link TD-W9980 | User Guide - Page 24
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 3-12 5. Configure the basic parameters for 2.4GHz wireless network in the following screen as shown in Figure 3-13, and then click Next. Figure 3-13 6.
  • TP-Link TD-W9980 | User Guide - Page 25
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 7. On this page, please confirm all parameters. Click Back to modify or click the Save button to save your configuration. Figure 3-15 8. You will see
  • TP-Link TD-W9980 | User Guide - Page 26
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration. 4.1 Login After your successful login, you will see the twenty-two main menus on the left of the Web-based
  • TP-Link TD-W9980 | User Guide - Page 27
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 17
  • TP-Link TD-W9980 | User Guide - Page 28
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.4 Operation Mode Choose "Operation Mode", and you will see the screen as shown in Figure 4-2. Select your desired mode and then click Save. Figure 4-2  xDSL Modem Router Mode: In this mode, the device enables multi-users to
  • TP-Link TD-W9980 | User Guide - Page 29
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.5.1 WAN Settings Choose "Network""WAN Settings", and you will see the WAN Port Information Table in the screen similar to Figure 4-3. 4.5.1.1 VDSL WAN Settings For VDSL mode, there are four different connection types, which
  • TP-Link TD-W9980 | User Guide - Page 30
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-4 DSL Modulation Type:  DSL Modulation Type: The modem router supports to 4049. 1) Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and
  • TP-Link TD-W9980 | User Guide - Page 31
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-5 WAN Service Setup:  Enable IPv4：Check the box to enable IPv4.  IP Address: Enter the IP Server (at least one) manually. The Route will use this IPv6 DNS Server for priority.  Default Gateway: Select a WAN Interface from the
  • TP-Link TD-W9980 | User Guide - Page 32
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  IPv6 Default Gateway: Select a WAN Interface from the drop-down list as the IPv6 default gateway. Click Advance, advanced selections of WAN Service Setup can be shown.  MTU (bytes): Maximum Transmission Unit Size. Check this
  • TP-Link TD-W9980 | User Guide - Page 33
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.  Enable
  • TP-Link TD-W9980 | User Guide - Page 34
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-7  PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive.  Connection Mode: For PPPoE connection, you can select Always on or
  • TP-Link TD-W9980 | User Guide - Page 35
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.  Enable
  • TP-Link TD-W9980 | User Guide - Page 36
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.5.1.2 ADSL WAN Settings For ADSL mode, there are six different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, PPPoA, IPoA and Bridge. You can select the corresponding types according to your
  • TP-Link TD-W9980 | User Guide - Page 37
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 1) Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below. Figure 4-11 Click Advance, advanced selections of ATM
  • TP-Link TD-W9980 | User Guide - Page 38
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Prefix Length: Enter the prefix length of the IPv6 address. The default value is 64.  IPv6 Gateway: Enter the gateway IPv6 address provided by your ISP.  IPv6 DNS Server / Secondary IPv6 DNS Server: Here you can set
  • TP-Link TD-W9980 | User Guide - Page 39
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-12 Click Advance, advanced selections for WAN Service Setup can be shown.  MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not
  • TP-Link TD-W9980 | User Guide - Page 40
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Set DNS Server manually: Choose "Set DNS Server manually", you can set DNS Server manually here. The modem router will use this DNS Server for priority.  Get IPv6 Address with Unicast: This is disabled by default. The minority
  • TP-Link TD-W9980 | User Guide - Page 41
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive.  Connection Mode: For PPPoE connection, you can select Always on or Connect on
  • TP-Link TD-W9980 | User Guide - Page 42
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-14 5) IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen. 32
  • TP-Link TD-W9980 | User Guide - Page 43
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-15  IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP.  DNS Server/Secondary DNS Server: Type in your preferred DNS server.  Default Gateway: Select a
  • TP-Link TD-W9980 | User Guide - Page 44
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-16  Note: After you finishing the instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. If you want to active Interface Grouping function, please
  • TP-Link TD-W9980 | User Guide - Page 45
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. Only the
  • TP-Link TD-W9980 | User Guide - Page 46
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-19  IP Address: You can configure the modem router's IP Address and Subnet Mask for LAN Interface.  IP Address: Enter the modem router's local IP Address, then you can access to the Web-based management page via the IP
  • TP-Link TD-W9980 | User Guide - Page 47
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.254.  Leased Time: The Leased Time is the
  • TP-Link TD-W9980 | User Guide - Page 48
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Leased Time: The Leased Time is List displays the WAN Interfaces you have configured on the section 4.5.1 WAN Settings and its default MAC Address. You can select corresponding WAN Interface from the drop-down list and click
  • TP-Link TD-W9980 | User Guide - Page 49
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Note: Only the WAN Ports can use ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data"
  • TP-Link TD-W9980 | User Guide - Page 50
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  H323 ALG: To allow H323 clients and servers to transfer data across NAT, click Enable.  SIP ALG: To allow SIP clients and servers to transfer data across NAT, click Enable. Click the Save button to save your settings. 4.5.7
  • TP-Link TD-W9980 | User Guide - Page 51
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Note: You could also use other VPN Routers to set VPN tunnels with TD-W9980. TD-W9980 supports up to 10 VPN tunnels simultaneously. Click Add New Connection in Figure 4-27 and then you will enter the screen shown in Figure 4-28
  • TP-Link TD-W9980 | User Guide - Page 52
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Tunnel access from local IP addresses: Choose Subnet if you want the Whole LAN to join the VPN network, or else choose Single Address if you want single IP to join the VPN network.  IP Address for VPN: Enter the IP address of
  • TP-Link TD-W9980 | User Guide - Page 53
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-29  Mode: Select Main Mode to configure the standard negotiation parameters for IKE phase1.  Aggressive Mode: Select Aggressive Mode to configure IKE phase1 of the VPN Tunnel to carry out negotiation in a shorter
  • TP-Link TD-W9980 | User Guide - Page 54
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Click any IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the modem router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP
  • TP-Link TD-W9980 | User Guide - Page 55
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Secondary DNS - (Optional.) Input the IP function working properly, please run on router mode only, disable the DHCP server on the LAN as "Obtain an IP Address automatically". 2) You have to disable NAT of the WAN connections,
  • TP-Link TD-W9980 | User Guide - Page 56
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 4-32  MAC Address: The MAC address of the PC for which you want to reserve an IP address.  IP Address:
  • TP-Link TD-W9980 | User Guide - Page 57
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-34 To add a vendor class: 1. Click the Add New button. Then Figure 4-35 running video and voice applications use the 5GHz band, while your guest access and computers that are only browsing the web use the 2.4GHz band. 47
  • TP-Link TD-W9980 | User Guide - Page 58
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-36  Concurrently with 2.4GHz and 5GHz (802.11a/b/g/n): Choose this option, and then the modem router will work concurrently in 2.4GHz and 5GHz frequency. 
  • TP-Link TD-W9980 | User Guide - Page 59
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-37  SSID: Wireless network name shared among all points .  Mode: Select the desired mode. 11b problems with another nearby access point.  Channel Width: Select the channel width from the drop-down list. The default
  • TP-Link TD-W9980 | User Guide - Page 60
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Note: If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the : Check this box to enable WDS. With this function, the modem router can bridge two or more Wlans. If this checkbox is selected, you will have to set
  • TP-Link TD-W9980 | User Guide - Page 61
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-38  WPS: Enable or disable the WPS function here.  Current PIN: The current value of the modem router's PIN is displayed here. The default PIN of the modem router can be found in the label or User Guide.  Restore PIN:
  • TP-Link TD-W9980 | User Guide - Page 62
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has
  • TP-Link TD-W9980 | User Guide - Page 63
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide There are three wireless security modes supported by the modem router: WPA/WPA2 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the default PIN code, which is labeled on the bottom of the
  • TP-Link TD-W9980 | User Guide - Page 64
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Authentication Type: Authentication Type: You can choose the type for the WPA/WPA2-Personal security on the drop-down list. The default setting is Auto, which can select WPA-PSK or WPA2-PSK authentication type automatically
  • TP-Link TD-W9980 | User Guide - Page 65
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-42. Figure 4-42 To filter wireless users by MAC Address, click Enable. The default entry, follow these instructions: 1. Enter
  • TP-Link TD-W9980 | User Guide - Page 66
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4. Click the Save button to save this Select the radio button "Allow the stations specified by any enabled entries in the list to access" for Filtering Rules. 3. Delete all or disable all entries if there are any entries already
  • TP-Link TD-W9980 | User Guide - Page 67
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-44  Transmit Power: Here you can specify the transmit power of modem router. You can select High, Middle or Low which you would like. High is the default setting and is recommended.  Beacon Interval: Enter a value
  • TP-Link TD-W9980 | User Guide - Page 68
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.8.6 Wireless Status Choose menu "Wireless 2.4GHz""Wireless Status", you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless
  • TP-Link TD-W9980 | User Guide - Page 69
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-46  SSID: Wireless network name shared among all points default SSID is set to be TP the Mode 11an problems with another nearby access point.  Channel Width: Select the channel width from the drop-down list. The default
  • TP-Link TD-W9980 | User Guide - Page 70
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Enable SSID Broadcast checkbox, the Wireless Router will broadcast its name (SSID) on the air. Click Save to save your settings. 4.9.2 WPS Settings This section will guide you to add a new wireless device to an existing network
  • TP-Link TD-W9980 | User Guide - Page 71
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide You can also keep the default WPS Status as Enabled and instructions. II. Enter the client device's PIN on the modem router Use this method if your client device has a Wi-Fi Protected Setup PIN number. Step 1: Keep the default
  • TP-Link TD-W9980 | User Guide - Page 72
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide wireless network. There are three wireless security modes supported by the modem router: WPA/WPA2 - Password: You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password
  • TP-Link TD-W9980 | User Guide - Page 73
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide IP: Enter the IP address of the Radius Server.  RADIUS Server Port: Enter the port that radius service used.  RADIUS Server Password: Enter the password on the drop-down list. The default setting is Auto, which can select
  • TP-Link TD-W9980 | User Guide - Page 74
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-42. Figure 4-51 To filter wireless users by MAC Address, click Enable. The default instructions: 64
  • TP-Link TD-W9980 | User Guide - Page 75
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 1. Enter the appropriate MAC Address Select the radio button "Allow the stations specified by any enabled entries in the list to access" for Filtering Rules. 7. Delete all or disable all entries if there are any entries already.
  • TP-Link TD-W9980 | User Guide - Page 76
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-53  Transmit Power: Here you can specify the transmit power of modem router. You can select High, Middle or Low which you would like. High is the default setting and is recommended.  Beacon Interval: Enter a value
  • TP-Link TD-W9980 | User Guide - Page 77
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-54  MAC Address: The connected wireless station's MAC address  Current Status: The you to create a separate network for your guests without allowing them to access your main network and the computers connected to it. 67
  • TP-Link TD-W9980 | User Guide - Page 78
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-55  Guest Network: You can choose your isolation is disabled by default.  Guest Network Bandwidth Control: With this function, you can configure the Upstream Bandwidth and Downstream Bandwidth for guest network. Click
  • TP-Link TD-W9980 | User Guide - Page 79
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.10.2 Guest Network Status Choose menu "Guest Network""Guest Network Status", you can see the MAC Address, Current Status, Received Packets and Sent Packets for
  • TP-Link TD-W9980 | User Guide - Page 80
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-56  Volume: The volume name of the USB drive the users have access password for Storage Sharing and FTP Server users on this page. Storage Sharing users can access which provide means to control the access to the USB mass
  • TP-Link TD-W9980 | User Guide - Page 81
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-57 To add a new user account, please follow the steps below: 1. Choose the index from the drop-down list of Choose Index. 2. Self-define a New Username. 3. Enter the password in the New Password field. 4. Re-enter the
  • TP-Link TD-W9980 | User Guide - Page 82
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Anonymous access to all the volumes: This function is enabled by default, so users can access all activated volumes of Storage Sharing without accounts. If you want to add a shared folder which does not allow anonymous login,
  • TP-Link TD-W9980 | User Guide - Page 83
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries.
  • TP-Link TD-W9980 | User Guide - Page 84
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 1. Click Add New Folder in Figure 4-61. Figure 4-62 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter
  • TP-Link TD-W9980 | User Guide - Page 85
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Server Enable: Select this box to enable this function.  Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add New Folder button, and
  • TP-Link TD-W9980 | User Guide - Page 86
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.12 Route Settings Choose "Route Settings", it includes four menus: Default Gateway, Static Route IPv6 Static Route and RIP Settings. The detailed descriptions are provided below. 4.12.1 Default Gateway Choose "Route Settings""
  • TP-Link TD-W9980 | User Guide - Page 87
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-68 2. Enter the following data:  Destination IP Address: The Destination IP Address is Select the Interface name in the text box, or else, the default Use Interface will be adopted for the Static Route.  Status:
  • TP-Link TD-W9980 | User Guide - Page 88
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide To add a new entry, follow the instructions below. 1. Click the Add IPv6 Gateway address correctly, and the option for Interface will adopt the default IPv6 Gateway address for the IPv6 Static Route.  Interface: Select the Interface
  • TP-Link TD-W9980 | User Guide - Page 89
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-71  Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.13 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any
  • TP-Link TD-W9980 | User Guide - Page 90
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide supported one type of available service. If so, select another service, and type the same IP address for that computer service port of the virtual server as 80, you must set the Web management port on System Tools -> Manage Control
  • TP-Link TD-W9980 | User Guide - Page 91
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide games, video conferencing, Internet telephoning and so on. Port Triggering is used for some of these applications that cannot work with a pure NAT modem router. Figure 4-74 To add a new rule, follow the steps below. 1. Click the
  • TP-Link TD-W9980 | User Guide - Page 92
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Open Port: The port or port range or ALL (all protocols supported by the modem router).  Status: The status of this entry, Enabled means the Port Triggering entry is enabled.  Common Service Port: Some popular applications
  • TP-Link TD-W9980 | User Guide - Page 93
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-76 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field. 3. Click the Save button. 4.13.4 UPnP
  • TP-Link TD-W9980 | User Guide - Page 94
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.14 Parental Control Choose menu "Parental Control", and you can configure the parental control in the screen as shown
  • TP-Link TD-W9980 | User Guide - Page 95
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.15 IPv4 Firewall There are four submenus and set Access Control rules in the screen as shown in Figure 4-79. Figure 4-79  Enable Firewall: Select the check box to enable the Firewalll function, so the Default Filtering Rules
  • TP-Link TD-W9980 | User Guide - Page 96
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide The methods to add a new rule: 1. Click the Add New button and the next screen will pop is unique.  Address Info: Here displays the information about the host. It can be IP or MAC.  Edit: To modify an existing entry. 86
  • TP-Link TD-W9980 | User Guide - Page 97
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.  If you select IP Address, please follow the steps below: 1) In Description field, create a
  • TP-Link TD-W9980 | User Guide - Page 98
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 2) In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-84. Figure 4-84 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In
  • TP-Link TD-W9980 | User Guide - Page 99
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below: 1. Click Add New button and the next screen will
  • TP-Link TD-W9980 | User Guide - Page 100
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.16.1 IPv6 Rule Choose menu "IPv6 Firewall" → "IPv6 Rule", and then you can view and set Access Control rules in the screen as shown in Figure 4-88. Figure 4-88  Enable IPv6 Firewall: Select the check box to enable the IPv6
  • TP-Link TD-W9980 | User Guide - Page 101
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4. Select a target from the IPv6 WAN Host drop-sown list or choose "Add IPv6 WAN Host". 5. Select a schedule from the IPv6 Schedule drop-down list
  • TP-Link TD-W9980 | User Guide - Page 102
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.16.3 IPv6 WAN Host Choose menu "IPv6 Firewall" → "IPv6 WAN Host", and then you can view and set a Host list in the screen as shown
  • TP-Link TD-W9980 | User Guide - Page 103
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide mechanism to enable IPv6-only hosts to reach IPv4 services and to allow isolated IPv6 hosts and networks to It is a temporary solution for networks that do not support native dual-stack, where both IPv6 and IPv4 run independently
  • TP-Link TD-W9980 | User Guide - Page 104
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-96  Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.  Mechanism: Select a type for IPv6 tunnel from the drop-down list. DS-Lite, 6RD and 6to4 are supported. 1) DS-Lite This type is used
  • TP-Link TD-W9980 | User Guide - Page 105
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-98  WAN Connection: Select a WAN means to obtain the following parameters automatically while Manual means you set them manually. If Auto is selected, only Dynamic IP connection can be selected from the drop-down
  • TP-Link TD-W9980 | User Guide - Page 106
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.18 Bandwidth Control Choose menu "Bandwidth Control", and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. The values you configure should be less than 1000000Kbps. For optimal control
  • TP-Link TD-W9980 | User Guide - Page 107
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-101 3. Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete selected entries. 4.19 IP&MAC Binding There are two
  • TP-Link TD-W9980 | User Guide - Page 108
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. This page is used for adding or modifying an IP & MAC Binding entry (shown in
  • TP-Link TD-W9980 | User Guide - Page 109
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Click the Load Selected button to load selected items to the IP & MAC Binding list. Click the Refresh button to refresh all items. 4.20 Dynamic DNS Choose menu "Dynamic DNS", and you can configure the Dynamic DNS
  • TP-Link TD-W9980 | User Guide - Page 110
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide 4.22 System Tools Figure 4-106 Choose menu "System Tools", and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware
  • TP-Link TD-W9980 | User Guide - Page 111
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Figure 4-107  Log Type: By selecting the log displayed.  Save Remotely: If Save Remotely is selected, events will be sent to the specified IP address and UDP port of the remote system log server. Click the Save button to save
  • TP-Link TD-W9980 | User Guide - Page 112
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide get time automatically once it connects the Internet. To set time manually: 1. Select your local time zone. 2. Enter the Date to the Internet. 4.22.3 Manage Control Choose "System Tools" → "Manage Control", you can see the screen (
  • TP-Link TD-W9980 | User Guide - Page 113
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Account Management: Here you can set the account user information about Old Password, New User Name, New Password and Confirm Password.  Service supports User Name/Password: Enter the User Name and password to login the ACS
  • TP-Link TD-W9980 | User Guide - Page 114
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide router contains SNMP "agent" software can be monitored and/or controlled by SNMP Manager using SNMP messages. 4.22.6 Backup & upgrade the modem router 's configuration, follow these instructions.  Click the Browse button to find
  • TP-Link TD-W9980 | User Guide - Page 115
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Note: The current configuration will be covered with the uploading configuration file. Wrong process will lead the device unmanaged. The restoring process lasts for 20
  • TP-Link TD-W9980 | User Guide - Page 116
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Firmware Version: Displays the current firmware version.  Hardware the modem router's firmware, follow these instructions below: 1) Download a most recent firmware upgrade file from our website (www.tp-link.com). 2) Enter
  • TP-Link TD-W9980 | User Guide - Page 117
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Restore the modem router's settings to factory defaults (system will Click the Refresh button to refresh immediately. Statistics Table: IP/MAC Address The IP and MAC address are displayed with related statistics. Total
  • TP-Link TD-W9980 | User Guide - Page 118
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide The number of UDP packets transmitted to the WAN per second UDP Tx at the specified the existing entry in the table. 4.23 Logout Choose "Logout", and you will back to the login screen as shown in Figure 4-118. Figure 4-118 108
  • TP-Link TD-W9980 | User Guide - Page 119
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, ITU G.993.2 Standards and Protocols IEEE802.11p, IEEE802.11e, IEEE802.11b, IEEE802.11g, IEEE802.11n, IEEE802.3, IEEE802.3u, TCP/IP, PPPoA,
  • TP-Link TD-W9980 | User Guide - Page 120
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my modem router's configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before
  • TP-Link TD-W9980 | User Guide - Page 121
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide  Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8  Move your mouse to the lower right corner and you will see
  • TP-Link TD-W9980 | User Guide - Page 122
    the instructions in 3.2 Quick Installation Guide. 5) Please contact our Technical Support if the problem still exists.  Note: For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support 112
  • TP-Link TD-W9980 | User Guide - Page 123
    TD-W9980 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Guide Appendix C: Technical Support Technical Support  For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq  To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
TD-W9980
N600 Wireless Dual Band Gigabit VDSL2 Modem
Router
Rev: 1.0.0
1910010923