TP-Link TL-SC3230N TL-SC3230N V1 User Guide

TP-Link TL-SC3230N Manual

Get TP-Link TL-SC3230N PDF manuals and user guides View all TP-Link TL-SC3230N manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-SC3230N manual content summary:

  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 1
    TL-SC3230N Wireless N Megapixel Surveillance Camera REV: 1.0.0 1910010754
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 3
    and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there FCC RF radiation exposure limits set forth for an uncontrolled environment. This camera and its antenna must not be co-located or operating in conjunction with
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 4
    having a maximum gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this camera. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 5
    power source. z Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. z Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 6
    TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: Wireless N Megapixel Surveillance Camera Model No.: TL-SC3230N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 7
    settings 22 6.1.1 Network 23 6.1.2 Wireless 24 6.1.3 HTTPS 27 6.1.4 DDNS service 27 6.1.5 PPPoE 29 6.1.6 Streaming 30 6.1.7 UPnP 30 6.1.8 Bonjour 31 6.1.9 ONVIF 32 6.1.10 IP Filter 33 6.1.11 IP Notification 34 6.2 Camera: Adjust camera parameters 36 6.2.1 Picture 36 6.2.2 Privacy
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 8
    56 6.13.1 Setting 56 6.13.2 Record 60 Appendix A: Troubleshooting & FAQ 62 Appendix B: PING IP Address 67 Appendix C: Bandwidth Estimation 68 Appendix D: Specifications 69 Appendix E: Configure Port Forwarding Manually 71 Appendix F: DDNS Application 74 Appendix G: Power Line Frequency
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 9
    items should be found in your package: ¾ TL-SC3230N Wireless N Megapixel Surveillance Camera ¾ Power Adapter ¾ Camera Stand with screws ¾ Detachable WLAN antenna ¾ RJ45 Cable ¾ Quick Installation Guide ¾ Resource CD, including: z This User Guide z Other helpful information ) Note: Make sure that
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 10
    IP Service to search your IP camera from Internet easily z H.264, MPEG4 and JPEG triple compression simultaneously z 1.3 Mega-pixel resolution z 1.3 Mega-pixel or 720P mode selectable z 8-profile encoder simultaneously z UDP / TCP / HTTP / HTTPS protocols selectable z IEEE 802.11n wireless LAN
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 11
    540 Intel Pentium D 950 3.4GHZ 1GB Display OS 1024x768 resolution or above Support DirectX 9.0c or above Intel 945G or Intel 965G or above Windows XP， = QVGA x 16 FULL HD FHD = QVGA X 24 To reach the Max. camera count, it is required to adjust the video resolution/FPS settings on each channel to
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 12
    has a SMA type antenna. Lens & focus ring: The user could use this ring to adjust focus manually. Microphone: The camera has a built-in internal microphone. This microphone is hidden in the pinhole located on the front panel. Micro SD Card Slot: The user can insert a
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 13
    unit and result in danger. Factory Default Reset: This button is hidden in the pinhole. This button is used to restore the all factory default settings. Sometimes restarting the camera will make the system back to a normal state. If the system still got problems after restart, the user can restore
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 14
    Installation Follow the steps below to mount your camera. 1. Attach the camera with the included stand 2. Place the camera on the table or fix it onto ceiling or wall Use three screws to fix the camera onto the ceiling or wall. You could also put the camera on the table directly. Fix it by Screws
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 15
    : Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power. Power Cable Once you have installed the camera well and powered it on, the Power LED (orange) will turn on later. Once the Power LED turned on, it means the system is booting
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 16
    ways to search your cameras by IP Search or UPnP™ discovery. Here is the way to execute IP Search to discover camera's IP address and set up related parameter in a camera. 4.1.1 Search When launch the IP Search, a searching window will pop up. IP Search is starting to search cameras on the LAN. The
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 17
    directly. Furthermore, you could double click the left button of mouse to link to the network camera by browser. 4.1.3 LAN In case you want to change the IP related parameters of wired interface, please select the camera you want to configure and click the LAN button. Relative settings will be
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 18
    to perform your setting accordingly. Click "
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 19
    In case you want to change the IP related parameters of wireless interface, please select the camera you want to configure and click the WIRELESS button. Relative settings will be carried out as above. Click SSID to select your wireless AP or router and key in WEP or WPA key. Click >> to go to
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 20
    Confirm the wireless setting and then submit the settings. Click OK to confirm these parameters, then IP Search will start to configure this camera with specified information. 12
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 21
    IP Search will prompt you to test wireless setting or finish wireless procedure as below. 4.2 UPnP of Windows® XP, Vista or 7 UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This camera
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 22
    To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function. This feature is not enabled by default in all routers. Please check user's manual of your NAT router for detail. 14
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 23
    Î UPnP page for detail NAT traversal setting. Note that this option is enabled by default. 4.4 Access the camera from the Internet Explorer for the first time 1. Start the web browser on the computer and type the IP address of the camera you want to monitor as below: 2. The Login Window of the
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 24
    4.5 Logging in as a User If you log in the camera as an ordinary user, "Setting" function will not be accessible. 4.6 Logging in as an Administrator If you log in the camera as an Administrator, you can perform all the settings provided by the camera. 16
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 25
    is shown here. The date and time are displayed at the top of the window. 5.2 Video Profile The camera supports multi-profile function for H.264, MEPG4 and JPEG simultaneously. The user can choose the proper and/or preferred profile which is listed here. 5.3 Streaming Protocol The user can select
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 26
    Click to activate this function as above. The user can scroll the mouth over the video to adjust zoom ratio and position. 5.7 2-Way Audio The camera supports 2-way audio function. Select the icon and you will see the and the control bar. The user can choose to enable or disable this function
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 27
    5.8 Record Click the icon to activate this function. Press to start recording. The video file is saved as ASF format into your local PC. While you want to stop it, press Stop to stop recording. Select Browser and the pop-up window will display. Select the save path and file name prefix, and
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 28
    5.9 Snapshot Click the icon to activate this function. Press to take a picture. The image file is saved as JPEG format into your local PC. Select Browser and the pop-up window will display. Select the save path and file name prefix, and select OK to continue. If you like to retrieve the saved
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 29
    5.10 About Click the icon to show this ActiveX information. 21
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 30
    Recording List Event Server Event Schedule Action Configure Network settings such as DHCP, DDNS, 3GPP, PPPoE and UPnP Adjust camera parameters, position, and set camera tour Configure system information, date & time, maintenance, and view system log file. Configure bit rate and frame rate of
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 31
    server is installed on the network and provide DNS service. ¾ Primary DNS and Secondary DNS: If you do not select Obtain DNS from DHCP, then you need to enter these parameters manually. ¾ HTTP Port: The camera supports two HTTP ports. The first one is default port 80 and this port is fixed. This
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 32
    can be assigned as the virtual server port mapping to support multiple cameras. Click OK to save and enable the setting. 6.1.2 Wireless If your camera is a wireless model, you could assign the related parameters into wireless setting. Using a wired connection ensures greater secrecy while making
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 33
    Step 2: Key in security key of WEP or WPA. Then click "Submit" button to activate wireless setting. If the user wants to configure wireless settings manually, please follow the steps as below: ¾ MAC address: Displays the Ethernet MAC address of the WLAN card. Note that the user can not change it. ¾
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 34
    the wireless channel in use currently. ¾ Security mode: Shows which type of security the network uses. The camera supports three security be entered either as Manual hex, as 64 hexadecimal characters, or as a Passphrase, using 8 to 63 ASCII characters. ¾ Obtain IP address automatically (DHCP):
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 35
    Transfer Protocol with the SSL/TLS protocol to provide encrypted communication camera will go through HTTPS only and HTTP service is no longer available. ¾ Port: Choose the HTTPS port. The default value is 443. 6.1.4 DDNS service DDNS: Stands for Dynamic Domain Name Server Your Internet Service
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 36
    is when you want to access your camera over the Internet. One of the possible solutions to the dynamic IP address problem comes in the form of a dynamic DNS service. A dynamic DNS service is unique because it provides a means of updating your IP address so that your listing will remain current
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 37
    . The procedures are • Connect to a LAN by DHCP or Fixed IP • Access the camera, and enter Setting Î Network Î PPPoE as below ¾ PPPoE: To enable or disable the PPPoE service here. ¾ User name: Type the user name for the PPPoE service which is provided by the ISP. ¾ Password: Type the password for
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 38
    video stream. The default range is 50000 to 50999. The user can specify a number between 1024 and 65535. 6.1.7 UPnP UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This camera is an UPnP
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 39
    function is failed. 6.1.8 Bonjour Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, cameras, and services on IP networks. Bonjour uses industry standard IP protocols to allow cameras to automatically discover each other without the need to enter
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 40
    enable or disable the Bonjour service here. ¾ Friendly Name: To show the friendly name of this camera here. 6.1.9 ONVIF ONVIF is a global and open industry forum with the goal to facilitate the development and use of a global open standard for the interface of physical IP-based security products. Or
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 41
    ¾ ONVIF: To enable or disable the ONVIF interface here. ¾ Version: Currently, the V1.0 or V1.01/V1.02/V2.0/V2.1.1 is available. 6.1.10 IP Filter You can enter different users' IP addresses which are allowed or denied to enter by the camera. 33
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 42
    ¾ IP Filter: To enable or disable the IP filter function here. ¾ IP Filter Policy: Choose the filter policy where is denying or allowing. 6.1.11 IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled. 34
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 43
    "Message" fields need to be filled. ¾ TCP Server: Type the server name or the IP address of the TCP server. ¾ TCP Port: Set port number of TCP server. ¾ Message fields below need to be filled. ¾ URL: Type the server name or the IP address of the HTTP server. ¾ HTTP Login name: Type the user name for
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 44
    can set specific parameters to HTTP server. ¾ Message: The message will be sent to HTTP server. 6.2 Camera: Adjust camera parameters Use this menu to set the functions of the camera parameters of the camera. 6.2.1 Picture ¾ Rotation: Turn the "Mirror" and "Vertical Flip" On or OFF. The image will be
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 45
    . ¾ Contrast: Large value will contrast camera heavily. ¾ Sharpness: Large value indicates the image will be sharpened. ¾ 3D De-Noise: 3D De-Noise can remove or lower unwanted noise and preserve fine details and edges. ¾ Default Settings: Restore to factory image settings. 6.2.2 Privacy Mask Use
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 46
    . The information will be shown on IP Search once the camera is found. ¾ Software Version: This information shows the software version of the camera. ¾ Network (LAN) LED: To turn on or off LAN LED. ¾ Power LED (Wireless LED): To turn on or off the Power LED (wireless LED if WLAN model). ¾ Log: The
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 47
    : Click this option to set time and date manually. - Synchronize with NTP: Click this option if you want to synchronize the camera's date and time with those of time server called NTP server (Network Time Protocol). ¾ NTP Server: Type the host name or IP address or domain name of the NTP server
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 48
    click the "Restore Setting" button. The settings will be restored to the previous configuration. ¾ Firmware Upgrade: The camera supports new firmware upgrade (the software that controls the operation in the camera). Please contact your dealer for the latest version if necessary. Download the latest
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 49
    any of the network settings. It means the IP address of the camera will not change after firmware upgrade. 6.4 Video: Configure profile This device provides 2 modes of video profile. The first one is 1.3 Mega mode which supports video resolution up to 1.3 Mega-pixel. Maximum frame rate of this mode
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 50
    6.4.1 Common ¾ Text Overlay Setting: There are some important information can be embedded into image, including date, time, and/or text. The user also can change the font color, background color, or transparency. 42
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 51
    6.4.2 Video Profile ¾ Name: To assign a name to the selected profile. ¾ Video Type: Video codec of the selected profile. ¾ Resolution: Shows the resolution of the selected profile. ¾ ROI: Assign the selected profile as a ROI stream or not. (Only available for the profiles with max resolution) ¾ Rate
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 52
    ¾ Max Frame Rate: Defines the targeted frame rate of this profile. For example, set the frame rate to 30 fps, then the image will be updated for 30 frames per second as possible. The user needs to set reasonable max frame rate versus video quality under the limited bandwidth. ¾ GOP Control: Defines
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 53
    6.5 Audio: Audio parameters ¾ Audio: To enable or disable audio function ¾ Audio Type: To select audio codec ¾ Audio Mode: To select Simplex or Full duplex (2-way audio) mode ¾ Input Gain: To adjust gain of input audio ¾ Output Gain: To adjust gain of output audio 6.6 User: Manage user name,
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 54
    they are connected. Otherwise, only users in database can view the video after login. ¾ Access Right: Administrator can access every function in this camera. However, viewers only can view the video and access limited function. ¾ Add, Modify, and Delete of Users account: Manage the user's account of
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 55
    ¾ SMTP Server: Type the SMTP server name or the IP address of the SMTP server. ¾ Test: Send a test mail to mail server to check this account is available or not. ¾ SMTP Port: Set port number of SMTP service. ¾ SSL: Enable SSL function or not. ¾ SMTP Authentication: Select the authentication required
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 56
    add or delete the motion windows. The user can specify up to 10 Included and/or Excluded windows to monitor the video captured by this camera. By dragging mouse on the image, you can change the position and size of the selected motion window accordingly. ¾ Included or Excluded Window: These windows
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 57
    below. ¾ Remove recordings order than: Delete old files by days. ¾ Remove oldest recordings when disk is: Delete old files by left capacity. 6.9.2 SAMBA Server The camera can send video stream to specified SAMBA server. 49
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 58
    : Type the IP address of the SAMBA server. ¾ Share: Type the video storage destination on the SAMBA server. ¾ SAMBA username: Type the user name to login the SAMBA server. ¾ SAMBA Login Password: Type the password to login the SAMBA server. 6.10 Continuous Recording The camera provides continuous
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 59
    ¾ Disable / Enable: Enable or disable the continuous recording feature in camera. ¾ Record File Type: Select video profile to be used in video recording. Please note that max. 5 minutes of video can be recorded. ¾ Disk: Select SD
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 60
    This page shows the event triggered or scheduled recorded video files list in SD card or on the samba server. The user may play or delete the selected file. 52
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 61
    a name for each FTP setting. ¾ FTP Server: Type the server name or the IP address of the FTP server. ¾ Test: Check the FTP server whether this account is for the FTP server. ¾ FTP Port: Set port number of FTP service. ¾ FTP Path: Set working directory path of FTP server. ¾ FTP Passive Mode: Select passive
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 62
    In addition to send video file to FTP server, the camera also can send event message to specified TCP server. ¾ Server: Type the server name or the IP address of the TCP server. ¾ TCP Port: Set port number of TCP server. 6.12.3 HTTP Server The camera also can send event message to specified HTTP
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 63
    name for each HTTP server setting. ¾ URL: Type the server name or the IP address of the HTTP server. ¾ Test: Check the HTTP server whether it is password for the HTTP server. ¾ Proxy Address: Type the server name or the IP address of the HTTP Proxy. ¾ Proxy Login name: Type the user name for
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 64
    a name for each HTTP server setting. ¾ SAMBA Server: Type the server name or the IP address of the SAMBA server. ¾ Test: Check the SAMBA server whether this account is available some actions provided by this camera. Where the Schedule Trigger will be activated by user-define interval without event
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 65
    ¾ Name: Name of the Event or Schedule. ¾ Enable: Enable or disable this Event or Schedule. ¾ Type: Event trigger or Schedule trigger. ¾ Enable Time: Define the feasible time slot. ¾ Trigger by: Select the triggered sources. ¾ Action: Define the actions once event triggered. Example 1: Send file to
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 66
    Example 2: Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00 1. Select event trigger. 2. Enable time: start from Friday 18:00 and keep work in 12 hours, so it will stop on Saturday 06:00. 3. Trigger by : Motion Area (Added in Object Detection page) 4. Action : Send
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 67
    Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. 1. Type: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Friday, and set start time from 18:00 and keep work in 6 hours. 3. Trigger by : You do not need to choose it,
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 68
    6.13.2 Record The user can choose the type of record file for event or schedule application. 60
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 69
    ¾ Record File Type: Choose a profile to record. ¾ Record File Prefix: Define the prefix of recorded filename. ¾ JPEG Picture Numbers: Define the picture numbers of JPEG to be sent out. (by mode) ¾ Pre-Trigger Duration: Define the maximum duration of pre-alarm. ¾ Best Effort Duration: Define the best
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 70
    default reset Username is admin and password is admin. Note that it's all case sensitive. Follow the steps below. Forgot the username and 1. Restore the factory default setting by pressing and holding password down more than 5 seconds on the camera. 2. Reconfigure the camera. Forgot the IP
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 71
    Explorer from the Microsoft webpage. IP Search program fails to save the network parameters. z Network may have trouble. Confirm the parameters and connections of the camera. UPnP NAT Traversal z Maybe NAT router does not support UPnP function. Please check user's manual of router and turn on
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 72
    with the private IP address and correct port number of camera. z When you use DDNS, you need to set Default Gateway and DNS server address. z If it's not working after above procedure, reset camera to default setting and installed it again. z If the problem is not solved, the camera might be
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 73
    consume 32 kbps. Disable audio to improve video. Your Internet connection may not have enough bandwidth to support streaming audio from the camera. Image Transfer on e-mail or FTP does not work. z Default Gateway and DNS server address should be set up correctly. z If FTP does not work properly
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 74
    is located in a very low light environment. Make the condition around the camera brighter or turn the White-light LED on. Miscellaneous Cannot play the recorded ASF file Have installed Microsoft®'s DirectX 9.0 or later and use the Windows
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 75
    . z Type ping x.x.x.x, where x.x.x.x is the IP address of the camera. For example, ping 192.168.1.103 The replies, as illustrated below, will provide an explanation to the problem. If you want to detect any other cameras conflicts with the IP address of camera, also can utilize the PING command but
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 76
    fast motion will produce higher bit rate vice versa. Actual results generated by the camera may be varying. Image Resolution 160 x 120 (QQVGA) 320 x 240 ( mode 64kbps~256kbps @ 30fps NA NA NA Average bit rate for H.264 mode 25kbps~512kbps @ 30fps 128kbps~2048kbps @ 30fps 384kbps~4096kbps @ 30fps
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 77
    Appendix D: Specifications Camera Image Camera Effective Pixels Sensitivity Lens IP Module Video Video Encoder Video Profile Frame Rate Image Setting Streaming Audio Audio Encoder Audio Streaming Microphone Audio Output Network Supported Protocols Security Users Ethernet Wireless System Integration
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 78
    Operating Humidity Dimension Viewing System OS Browser Cell Phone Video Player Software Search & Installation Bundled NVR Program 12V DC external power adapter 2W 3W RJ-45 10BaseT/100BaseTX DC power jack Audio out Factory default reset Micro SD card (Max 32GB, Class 6) Green and orange LEDs
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 79
    it to be recognized by the router. Manually set up the camera with a fixed IP address, for example, 192.168.0.100. (2) Access the Router with Your Web browser The following steps generally apply to any router that you have on your network. The TP-LINK TL-WR841ND is used as an example to clarify
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 80
    that will not change over time and will be more convenient for you to use to access your camera from a remote location. If you could not get a Static IP address from your ISP or DDNS is a solution alternatively. (3) Open/set Virtual Server Ports to enable remote image viewing The firewall security
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 81
    need to change the port the camera uses from 80 to something else, such as 8080. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports. Then the camera can be accessed from WAN by the router's WAN IP Address. By now, you have finished
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 82
    tracked by a DDNS server. Host your own camera and much more no matter what your computer's IP address may be and even if you have dialup, DSL or cable modem internet connection where your computer's IP address changes all the time!! DDNS service supports all top level domain names including but not
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 83
    (3) After the columns show up at the left side, click "Create Account". (4) Fill the application agreement and necessary information. a) Username b) E-mail address and confirmation c) Password and confirmation 75
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 84
    d) Submit all the input information and finish creating an account Click these two options (5) Check your e-mail mailbox. There will be an e-mail with a title "Your DynDNS Account Information". Click the hyperlink address to confirm the DDNS service that you just applied. 76
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 85
    Then DDNS you applied activated. Click to confirm (6) Enter the web page http://www.dyndns.org/ again. Input your username and password that you just applied to login administration interface of DDNS server. Input your account (7) If the correct username and password are input, you can see the
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 86
    top-right of the login page. (8) Click the "Services". (9) Click the "Dynamic DNS ". (10) Click the "Get Started". 78
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 87
    the domain name information and finish DDNS application. (Pink No.4) 1 2 3 4 4. Set up the DDNS and PPPoE of Camera At last, users have to enter the web page of camera and set up the necessary information of DDNS and PPPoE after the application of DDNS service. Please check the user manual to 79
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 88
    access the DDNS and PPPoE pages. After saving the modification, restart the camera. Then the external users could browse the Networked camera by the input of their domain name. 80
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 89
    Appendix G: Power Line Frequency Country Argentina Voltage Frequency 220V 50 Hz Australia Austria 230V* 50 Hz 230V 50 Hz Brazil 110/220V* 60 Hz Canada China, Republic of Finland France Germany Hong Kong India Italy People's 120V 220V 230V 230V 230V 220V* 230V 230V Japan 100V
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 90
    that to use the 3GPP function, it strongly recommends to install the camera with a public and fixed IP address without any firewall protection. RTSP Port: Port 554 is the default for RTSP service. However, sometimes, some service providers change this port number for some reasons. If so, the user
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 91
    Appendix I: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operating system of PC is running Windows XP. Go to Start > Settings. Click Control Panel Click Add or Remove Programs 83
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 92
    Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details 84
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 93
    Select Universal Plug and Play Click OK Click Next 85
  • TP-Link TL-SC3230N | TL-SC3230N V1 User Guide - Page 94
    Please wait while Setting up configures the components. Click Finish 86
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
TL-SC3230N
Wireless N Megapixel Surveillance Camera
REV: 1.0.0
1910010754