TP-Link TL-SG1016D User Guide
TP-Link TL-SG1016D Manual
 |
UPC - 845973020613
View all TP-Link TL-SG1016D manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link TL-SG1016D manual content summary:
- TP-Link TL-SG1016D | User Guide - Page 1
User Guide TL-SG1008 8-Port Gigabit Switch TL-SG1016D 16-Port Gigabit Switch TL-SG1024D 24-Port Gigabit Switch Rev: 2.0.1 7106503502 - TP-Link TL-SG1016D | User Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link TL-SG1016D | User Guide - Page 3
equipment has been tested and found not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. which case the user may be required to take adequate measures. Note: As for TL-SG1008, a fuse resistor is used in the "F1" position on the PCB - TP-Link TL-SG1016D | User Guide - Page 4
...3 2.2 Rear Panel ...3 Chapter 3 Installation ...4 3.1 Precautions ...4 3.2 Installation ...4 3.2.1 Desktop Installation 5 3.2.2 Rack Installation 5 3.3 Connect to Ground 7 3.4 Power on ...8 Appendix A: Specifications 9 Appendix B: Troubleshooting 11 Appendix C: Contact Information 11 III - TP-Link TL-SG1016D | User Guide - Page 5
Package Contents The following contents should be found in your package: ¾ One TL-SG1008/TL-SG1016D/TL-SG1024D Switch ¾ One power cord ¾ This User Guide ¾ Rubber footpads for Desk-mount ¾ Mounting screws and two "L" planks Note: Make sure that the package contains the above items. If any of the - TP-Link TL-SG1016D | User Guide - Page 6
path to faster Gigabit speeds. The TL-SG1008/TL-SG1016D/TL-SG1024D Switch is plug-and-play and no configuration is required. Auto MDI/MDI-X cable detection on all ports eliminate the need for crossover cable or Uplink port. Each port can be used as general ports or Uplink ports, and any port can be - TP-Link TL-SG1016D | User Guide - Page 7
, rear panel and LED indicators of the Switch. TL-SG1008/TL-SG1016D/TL-SG1024D just differ in the number of LED indicators and ports and all figures in this guide are of TL-SG1008. 2.1 Front Panel The front panel of TL-SG1008 consists of switch model, switch LED indicators, and 8 10/100/1000Mbps RJ - TP-Link TL-SG1016D | User Guide - Page 8
Location Requirements When you choose a location for the Switch, please follow these guidelines: • Install the Switch on a flat and stable surface that can support the entire weight of the Switch with all fittings. • Locate the Switch far from strong electromagnetic field generators (such as motors - TP-Link TL-SG1016D | User Guide - Page 9
the power cord before installing or removing the Switch. 3.2.1 Desktop Installation To install the Switch on the desktop, please follow the steps: 1) Set the Switch on a flat surface strong enough to support the entire weight of the Switch with all fittings. 2) Remove the adhesive backing papers - TP-Link TL-SG1016D | User Guide - Page 10
the Switch, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure. Figure 3-3 Mounting Switch 3) Connect the Switch to network devices. 4) Supply power to the Switch with the provided power cord. Note: TL-SG1016D and TL-SG1024D do not support - TP-Link TL-SG1016D | User Guide - Page 11
, which is also a necessary measure to protect the body from electric shock. In different environments, the Switch may be grounded differently. The following will instruct you to connect the Switch to the ground in two ways, connecting to the Grounding Bar or connecting to the Ground via the power - TP-Link TL-SG1016D | User Guide - Page 12
in the electrical outlet is well grounded in advance. 3.4 Power on The TL-SG1008/TL-SG1016D/TL-SG1024D Switch is powered by an AC Power Supply. Connect the Switch and power outlet by power cord. Powering on the Switch, it will be automatically initialized and the LED indicators should respond as - TP-Link TL-SG1016D | User Guide - Page 13
STP (maximum 100m) Number of Ports 8/16/24 10/100/1000Mbps Auto-Negotiation RJ-45 ports LED indicators POWER, Link/Act, 1000Mbps Transfer Method Store-and-Forward MAC Address Learning Automatically learning, automatically aging 10Base-T: 14881pps/Port Frame Filter Rate 100Base-Tx: 148810pps - TP-Link TL-SG1016D | User Guide - Page 14
Environmental and Physical Operating Temperature Storage Temperature Operating Humidity Storage Humidity 0℃~40℃ (32℉~104℉) -40℃~70℃ (-40℉~158℉) 10%~90% non-condensing 5%~90% non-condensing 10 - TP-Link TL-SG1016D | User Guide - Page 15
working well. ¾ The cable must be less than 100 meters long(328 feet). Appendix C: Contact Information For help with the installation or operation of the TP-LINK TL-SG1008/TL-SG1016D/ TL-SG1024D Switch, please contact us. E-mail: [email protected] Website: http://www.tp-link.com 11 - TP-Link TL-SG1016D | User Guide - Page 16
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
User Guide
TL-SG1008
8-Port Gigabit Switch
TL-SG1016D
16-Port Gigabit Switch
TL-SG1024D
24-Port Gigabit Switch
Rev: 2.0.1
7106503502