TP-Link TL-SG3424P TL-SG3424P V1 CLI Guide

TP-Link TL-SG3424P Manual

Get TP-Link TL-SG3424P PDF manuals and user guides View all TP-Link TL-SG3424P manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-SG3424P manual content summary:

  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 1
    TL-SG3424P JetStream L2 Managed PoE Switch Rev: 1.0.0 1910010613
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 2
    are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 3
    1.1.1 Logon by a console port 4 1.1.2 Logon by Telnet ...6 1.2 CLI Command Modes ...8 1.3 Security Levels ...10 1.4 Conventions ...11 1.4.1 Format Conventions 11 1.4.2 Special Characters 11 1.4.3 Parameter Format 11 Chapter 2 User Interface 12 enable...12 enable password ...12 disable ...13
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 4
    ...32 show gvrp interface ...33 Chapter 8 LAG Commands 34 interface link-aggregation ...34 interface range link-aggregation 34 link-aggregation ...35 link-aggregation hash-algorithm 36 description ...36 show interfaces link-aggregation 37 Chapter 9 LACP Commands 38 lacp system-priority ...38
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 5
    ...41 user remove ...42 user modify status ...42 user modify type ...43 user modify password...43 user access-control disable 44 user access-control ip-based 44 user access-control mac-based 45 user access-control port-based 45 user max-number ...46 user idle-timeout...46 show user account-list
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 6
    dot1x retry ...69 dot1x(interface) ...69 dot1x guest-vlan ...70 dot1x port-control ...70 dot1x port-method ...71 radius authentication primary-ip 72 radius authentication secondary-ip 72 radius authentication port ...73 radius authentication key...73 radius accounting enable...74 radius accounting
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 7
    address port-security 91 bridge address static ...92 bridge aging-time...92 bridge address filtering ...93 show bridge port-security ...94 show bridge address ...94 show bridge aging-time ...95 Chapter 19 System Commands 96 system-descript ...96 system-time gmt ...96 system-time manual ...97
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 8
    ...97 ip address...98 ip management-vlan ...99 ip dhcp-alloc ...99 ip bootp-alloc ...99 reset ...100 reboot ...100 user-config backup ...101 user-config load...101 user-config save ...102 firmware upgrade ...102 ping ...103 tracert ...103 loopback ...104 show system-info...104 show ip address ...105
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 9
    ...123 mirror remove group ...124 mirror remove mirrored...124 show mirror...125 Chapter 23 Port isolation Commands 126 port isolation ...126 show port isolation...126 Chapter 24 PoE Commands 128 power inline consumption (global configuration 128 power inline disconnect-method 128 power inline
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 10
    -acl ...142 acl edit rule std-acl...143 acl policy policy-add ...144 acl policy action-add ...145 acl edit action ...146 acl bind to-port...146 acl bind to-vlan ...147 show acl time-segment...147 show acl holiday ...148 show acl config...148 show acl bind...149 Chapter 26
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 11
    -config 168 show igmp-snooping vlan-config 169 show igmp-snooping multi-vlan 169 show igmp-snooping multi-ip-list 169 show igmp-snooping filter-ip-addr 170 show igmp-snooping port-filter 170 show igmp-snooping packet-stat 171 show igmp-snooping packet-stat-clear 171 Chapter 28 SNMP Commands
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 12
    201 cluster ndp...201 cluster ntdp ...202 cluster explore ...203 cluster ...203 cluster manage role-change 204 show cluster ndp global ...204 show cluster ndp port-status 205 XI
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 13
    show cluster neighbour...205 show cluster ntdp global ...205 show cluster ntdp port-status 206 show cluster ntdp device ...206 show cluster manage role...207 XII
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 14
    for network administrator to provide referenced information about CLI (Command Line Interface). The device mentioned in this Guide stands for TL-SG3424P JetStream L2 Managed PoE Switch. Overview of this Guide Chapter 1: Using the CLI Provide information about how to use the CLI, CLI Command Modes
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 15
    Provide information about the commands used for Address configuration. Chapter 19: System Commands Provide information about the commands used for configuring the System information and System IP, reboot and reset the switch, upgrade the switch system and other operations. Chapter 20: Ethernet
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 16
    Protocol). Chapter 27: IGMP Commands Provide information about the commands used for configuring the IGMP Snooping (Internet Group Management Protocol Snooping). Chapter 28: SNMP Commands Provide information about the commands used for configuring the SNMP (Simple Network Management Protocol)
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 17
    two methods: 1. Log on to the switch by the console port on the switch. 2. Log on to the switch remotely by a Telnet or SSH connection through an Ethernet port. 1.1.1 Logon by a console port To log on to the switch by the console port on the switch, please take the following steps: 1. Connect
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 18
    Figure 1-2 Connection Description 4. Select the port to connect in figure 1-3, and click OK. Figure 1-3 Select the port to connect 5. Configure the port selected in the step above as the following figure1-4 shown. Configure Bits per second as 38400, Data bits as 8, Parity as None, Stop bits as 1,
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 19
    1-4 Port Settings 6. Type the User name and Password in the Hyper Terminal window, the factory default value for both of them is admin. The DOS prompt" TP-LINK>" will appear after pressing the Enter button as figure1-5 shown. It indicates that you can use the CLI now. Figure 1-5 Log in the Switch
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 20
    Figure 1-6 Open the Run window 3. Type cmd in the prompt Run window as figure 1-7 and click OK. Figure 1-7 Run Window 4. Type telnet 192.168.0.1 in the command prompt shown as figure1-8, and press the Enter button. Figure 1-8 Connecting to the Switch 7
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 21
    Password (the factory default value for both of them is admin) and press the Enter button, then you can use the CLI now, which is shown as figure1-9. Figure 1-9 Log in the Switch Mode can also be divided into Interface Ethernet, Interface link-aggregation and some other modes, which is shown as
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 22
    User EXEC mode. TP-LINK# Use the exit command to disconnect the switch (except that the switch is connected through the Console port). Enter the PC and the switch is established by a console port or by a telnet connection. 2. Each command mode has its own set of specific commands. To configure
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 23
    to the User level once connecting console port with the switch or logging in by Telnet. However, Guest users are restricted to access the CLI. Users can enter Privileged EXEC mode from User EXEC mode by using the enable command. In default case, no password is needed. In Global Configuration Mode
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 24
    1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: ¾ Items in square brackets [ ] are optional ¾ Items in braces be entered in special formats which are shown as follows: ¾ MAC Address must be enter in the format of xx:xx:xx:xx:xx:xx ¾ One or several values
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 25
    : TP-LINK>enable Enter password： TP-LINK# enable password Description The enable password command is used to set the password for users to access Privileged EXEC Mode from User EXEC Mode. To return to the default configuration, please use no enable password command. Syntax enable password password
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 26
    Mode from Privileged EXEC Mode. Syntax configure Command Mode Privileged EXEC Mode Example Access Global Configuration Mode from Privileged EXEC Mode: TP-LINK# configure TP-LINK(config)# exit Description The exit command is used to return to the previous Mode from the current Mode. Syntax exit 13
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 27
    Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode,and then return to Privileged EXEC Mode: TP-LINK(config-if)# exit TP-LINK(config)#exit TP-LINK# end Description The end command is used to return to Privileged EXEC Mode. Syntax end Command Mode Any
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 28
    traffic to specific domains. vlan database Description The vlan database command is used to access VLAN Configuration Mode for creating, deleting 802.1Q VLAN and other operations. Syntax vlan database Command Mode Global Configuration Mode Example Access VLAN Configuration Mode: TP-LINK(config
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 29
    vlan vlan-id Parameter vlan-id --VLAN ID,ranging from 1 to 4094. Command Mode Global Configuration Mode Example Configure the VLAN2: TP-LINK(config)# interface vlan 2 description Description The description command is used to assign a description string to a VLAN. To clear the description, please
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 30
    Command Mode Interface Configuration Mode ( interface ethernet / interface range ethernet ) Example Specify the Link Type of port 5 as general: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)#switchport type general switchport allowed vlan Description The switchport allowed vlan command is
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 31
    PVID for the switch ports. Syntax switchport pvid vlan-id Parameter vlan-id -- VLAN ID, ranging from 1 to 4094. Command Mode Interface Configuration Mode (interface ethernet / interface range ethernet ) Example Specify the PVID of port 2 as 2: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 32
    . Syntax show interface switchport [port-num] Parameter port-num -- The port number. By default, display the VLAN configuration information of all ports. Command Mode Any Configuration Mode Example Display the VLAN configuration information of all ports: TP-LINK(config)# show interface switchport 19
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 33
    ranging from 1 to 4094. mac-addr -- MAC address. description --Give a description to the MAC address for identification.By default , it is empty. Command Mode Global Configuration Mode Example Create VLAN 2 named "RD",and the MAC address is 00:00:00:00:00:01: TP-LINK(config)# mac-vlan add 2 00:00:00
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 34
    Delete the existing MAC-Based VLAN entry with the MAC address of 00:00:00:00:00:02: TP-LINK(config)# mac-vlan remove 00:00:00:00:00:02 Mode Example Modify the VLAN ID of the MAC VLAN entry with the MAC address of 00:00:00:00:00:02 as 12: TP-LINK(config)# mac-vlan modify 12 00:00:00:00:00:02 show mac
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 35
    arp" whose Frame-type is ethernet2, Ethernet protocol type is 0806. Delete the Protocol template whose number is 2: TP-LINK(config)# protocol-vlan template add arp 0806 ethernet2 TP-LINK(config)# protocol-vlan template remove 2 protocol-vlan vlan Description The protocol-vlan vlan command is used to
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 36
    number by the show protocol-vlan vlan command. member-list -- The port numbers needed to be added in the vlan. Command Mode Global Configuration the Protocol VLAN entry whose number is 1: TP-LINK(config)# protocol-vlan vlan 2 template 1 4-6,8 TP-LINK(config)# no protocol-vlan vlan 1 show protocol
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 37
    show protocol-vlan vlan Command Mode Any Configuration Mode Example Display information of the protocol-vlan entry: TP-LINK(config)# show protocol-vlan vlan 24
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 38
    data stream. By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs, you can perform TP-LINK(config)# voice-vlan enable 2 voice-vlan aging-time Description The voice-vlan aging-time command is used to set the aging time for a voice VLAN. To restore to the default
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 39
    ) to be set for the Voice VLAN. It ranges from 1 to 43200 and the default value is 1440. Command Mode Global Configuration Mode Example Set the aging time for the Voice VLAN as 2880 minutes: TP-LINK(config)# voice-vlan aging-time 2880 voice-vlan priority Description The voice-vlan priority command
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 40
    the OUI for identification which contains 16 characters at most. By default, it is empty. Command Mode Global Configuration Mode Example Create a Voice VLAN OUI descripted as TP-LINK Phone with the MAC address 00:01:E3:00:00:01 and the mask address FF:FF:FF:00:00:00. Andthen delete the Voice VLAN
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 41
    Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable Ethernet port 2 for the Voice VLAN security mode: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# switchport voice-vlan security enable show voice-vlan global Description The show voice
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 42
    -vlan switchport [port] Parameter port -- Ethernet port. By default, it will display the configuration information of all the ports in the Voice VLAN. Command Mode Any Configuration Mode Example Display the configuration information of all the ports in the Voice VLAN: TP-LINK(config)# show voice
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 43
    propagate the local VLAN registration information to other switches, without having to individually configure each VLAN. TP-LINK(config)# gvrp gvrp (interface) Description The gvrp(interface) command is used to enable the GVRP function for the desired port.To disable the GVRP function of this port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 44
    the GVRP registration mode on the port 2-6 to fixed: TP-LINK(config)# interface range ethernet 2-6 TP-LINK(config-if)# gvrp registration fixed gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired port. To restore to the default setting of a GARP timer, please use
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 45
    Join message. Once the Leave Timer is set, the GARP port receiving a Leave message will start its Leave timer, and port 6 to 2000 centiseconds and restore to the join timer of it to the default value: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# gvrp timer leaveall 2000 TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 46
    interface [ethernet port-num] Parameter port-num --The Ethernet port number. By default, the GVRP configuration information of all the Ethernet ports is displayed. Command Mode Any Configuration Mode Example Display the GVRP configuration information of all the Ethernet ports: TP-LINK(config)# show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 47
    -aggregation Mode and configure the aggregation group 1: TP-LINK(config)# interface link-aggregation 1 TP-LINK(config-if)# interface range link-aggregation Description The interface range link-aggregation command is used to access the Interface range Link-aggregation Mode, and you can configure some
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 48
    configure the aggregation group 1,4-6: TP-LINK(config)# interface range link-aggregation 1,4-6 TP-LINK(config-if)# link-aggregation Description The link-aggregation command is used to add the current Ethernet port to a aggregation group. To remove the current Ethernet port from the aggregation group
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 49
    -- The source and destination MAC addresses. src_dst_ip --The source and destination IP addresses. Command Mode Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as src_dst_mac: TP-LINK(config)# link-aggregation hash-algorithm src_dst_mac description Description
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 50
    group-num --The LAG number,ranging from1 to 14. By default, the LAG configuration information of all the Ethernet ports is displayed. Command Mode Any Configuration Mode Example Display the LAG configuration information of all the Ethernet ports: TP-LINK(config)#show interface link-aggregation 37
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 51
    link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link from 0 to 65535. By default, the value is 32768. Example Set global lacp system priority 1024: TP-LINK(config)# lacp system-priority
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 52
    admin key of port 1 as 1024: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# lacp admin-key 1024 lacp port-priority Description The lacp port-priority command is used to set the port priority for a port. To restore to the default priority, please use no lacp port-priority command. Syntax
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 53
    -num -- The Ethernet port number. By default, display the configuration information of all the Ethernet ports. Command Mode Any Configuration Mode Example Display the configuration information of all the Ethernet ports: TP-LINK(config)# show lacp interface show lacp system-priority Description The
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 54
    name and password for users to log on to the Web management page with a certain access level so as to protect the settings of the switch from being randomly tplink, and of which the password is password: TP-LINK(config)#user add tplink password password confirm-password password admin enable 41
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 55
    Syntax user remove user-name Parameter user-name -- An existing user name. Command Mode Global Configuration Mode Example Delete the user named tplink: TP-LINK(config)# user remove tplink user modify status Description The user modify status command is used to modify the status of the existing user
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 56
    level of tplink to admin: TP-LINK(config)# user modify type tplink admin user modify password Description The user modify password command is used to modify the password for the existing user. Syntax user modify password user-name old-password new-password confirm-password Parameter user-name -- The
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 57
    Example Modify the password of tplink as newpwd: TP-LINK(config)# user modify password tplink password newpwd newpwd user access- login. Syntax user access-control ip-based ip-addr ip-mask Parameter ip-addr / ip-mask --The source IP address. Only the users within the IP-range you set here are allowed
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 58
    access-control of the user whose MAC address is 00:00:13:0A:00:01: TP-LINK(config)# user access-control mac-based 00:00:13:0A:00:01 user access-control port-based Description The user access-control port-based command is used to to limit the ports for login. Only the users connected to
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 59
    access-control of the ports 2, port4, port5, port6,and port8: TP-LINK(config)# user access-control port-based 2,4-6,8 user max TP-LINK(config)# user max-num 5 3 user idle-timeout Description The user idle-timeout command is used to configure the timeout time of the switch. To restore to the default
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 60
    -timeout Parameter minute --The timeout time, ranging from 5 to 30 in minites. By default, the value is 10. Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minites: TP-LINK(config)# user idle-timeout 15 show user account-list Description The show user
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 61
    Command Mode Any Configuration Mode Example Display the security configuration information of the users: TP-LINK(config)# show user configuration 48
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 62
    the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port IP is 192.168.0.1, MAC is 00:00:00:00:00:01, VLAN ID is 2 and the Port number is 5 manually. Andthen enable the entry for the ARP detection.: TP-LINK(
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 63
    Mode Global Configuration Mode Example Delete the IP-MAC -VID-PORT entry with the index 5: TP-LINK(config)# binding-table remove index 5 dhcp-snooping Description The dhcp-snooping command is used to enable the DHCP-snooping function for the switch. To disable the DHCP-snooping function, please
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 64
    switch per second. The excessive massages will be discarded. The options are 0/10/20/30/40/50 (packet/second).By default, it is 0 standing for disable. dec-threshold --The value to specify the minimum transmission rate of the Decline packets to trigger the Decline protection for the specific port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 65
    Example Enable the Option 82 function of DHCP Snooping: TP-LINK(config)# dhcp-snooping information enable dhcp-snooping information strategy of the packets. It is the default option. replace --Indicates to replace the Option 82 field of the packets with the switch defined one. drop --Indicates to
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 66
    Option 82 field of the packets with the switch defined one and then send out: TP-LINK(config)# dhcp-snooping information strategy replace dhcp- Configuration Mode Example Permit users to define the Option 82: TP-LINK(config)# dhcp-snooping information user-defined dhcp-snooping information remote-
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 67
    ID for the customized Option 82 as tplink: TP-LINK(config)# dhcp-snooping information circuit-id tplink dhcp-snooping trusted Description The dhcp-snooping trusted command is used to configure a port to be a Trusted Port. Only the Trusted Port can receive the DHCP packets from DHCP servers.To
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 68
    mac-verify command. There are two fields of the DHCP packet containing the MAC address of the Host. The MAC Verify feature is to compare the two fields and discard Enable the MAC Verify feature for the port 2: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# dhcp-snooping mac-verify dhcp
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 69
    default value is 0, which stands for disable. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Set the Flow Control of port 2 as 20 pps: TP-LINK(config)# interface ethernet 2 TP-LINK of port 2: TP-LINK(config)# interface ethernet 2 TP-LINK(config-
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 70
    Mode Any Configuration Mode Example Display the IP-MAC-VID-PORT binding table: TP-LINK(config)# show binding-table show dhcp- Any Configuration Mode Example Display the configuration of DHCP Snooping globally: TP-LINK(config)# show dhcp-snooping global show dhcp-snooping information Description The
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 71
    show dhcp snooping interface [ethernet port-num] Parameter port-num --The number of the switch port. By default, it will display the configuration of all the ports. Command Mode Any Configuration Mode Example Display the interface configuration of all the ports: TP-LINK(config)# show dhcp-snooping
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 72
    : TP-LINK(config)# arp detection arp detection trust-port Description The arp detection trust-port command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted Port. To clear the Trusted Port list, please use no arp detection trust-port command .The specific
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 73
    Enable the arp defend function for the ports 2-6: TP-LINK(config)# interface range ethernet 2-6 TP-LINK(config-if)# arp detection arp detection limit-rate Description The arp detection limit-rate command is used to configure the speed. The switch can terminate receiving the ARP packets for 300
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 74
    (packet/second). By default, the value is 15. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the maximum amount of the received ARP packets per second as 50 pps for the port 5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# arp
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 75
    . Syntax show arp detection interface [ethernet port-num] Parameter port-num --The number of switch port. By default, display the configuration of all the ports. Command Mode Any Configuration Mode Example Display the configuration of all the ports: TP-LINK(config)# show arp detection interface show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 76
    Any Configuration Mode Example Display the number of the illegal ARP packets received: TP-LINK(config)# show arp detection statistic show arp detection statistic reset Description The show arp detection statistic reset command is used to clear the statistic fo the the illegal ARP packets received
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 77
    service requests to the Host. With the DoS Defend enabled, the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working defend function globally: TP-LINK(config)# dos-prevent [null-scan] [port-less-1024] [blat] [ping-flood] [syn-flood
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 78
    attack is enabled, the switch will automatically limit the tansmission rate of SYN/SYN-ACK packets to 512K upon being attacked.. Command Mode Global Configuration Mode Example Enable three DoS Defend Types named Land attack, Xma Scan attack and Ping flooding attack: TP-LINK(config)# dos-prevent type
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 79
    is to provide an access control for LAN ports via the authentication. Only the supplicant passing TP-LINK(config)# dot1x dot1x auth-method Description The dot1x auth-method command is used to configure the Authentication Method of IEEE 802.1X. To restore to the default switch and the client. The 66
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 80
    uses extensible authentication protocol (EAP) to exchange information between the switch and the client. The EAP protocol packets with authentication data Example Configure the Authentication Method of IEEE 802.1X as pap: TP-LINK(config)# dot1x auth-method pap dot1x guest-vlan Description The dot1x
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 81
    TP-LINK(config)# dot1x quiet-period dot1x timer Description The dot1x timer command is used to configure the Quiet Period and the SupplicantTimeout. To restore to the default in seconds. By default, it is 10. Once the supplicant failed to the 802.1X Authentication, then the switch will not respond to
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 82
    . By default, the value is 3. Command Mode Global Configuration Mode Example Configure the maximum transfer times of the repeated authentication request as 5: TP-LINK(config)# dot1x retry 5 dot1x(interface) Description The dot1x command is used to enable the IEEE 802.1X function for a specified port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 83
    Guest VLAN function for port 2: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# dot1x guest-vlan dot1x port-control Description The dot1x port-control command is used to configure the Control Mode of IEEE 802.1X for the specified port. To restore to the default configuration, please use no
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 84
    port is forbidden working for its fixed unauthorized status. By default, the Control Mode is auto. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the Control Mode for port 1 as authorized-force: TP-LINK(config)# interface ethernet 1 TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 85
    ethernet 5 TP-LINK(config-if)# dot1x port-method port-based radius authentication primary-ip Description The radius authentication primary-ip command is used to configure the IP addressof the authentication server. Authentication server provides the authentication service for the switch via the
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 86
    The IP address of the alternate authentication server. By default, it is 0.0.0.0. Command Mode Global Configuration Mode Example Configure the IP address of the alternate authentication server as 10.20.1.101: TP-LINK(config)# radius authentication secondary-ip 10.20.1.101 radius authentication port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 87
    which contains 15 characters at most.. Command Mode Global Configuration Mode Example Configure the shared password for the switch and the authentication servers as tplink: TP-LINK(config)# radius authentication key tplink radius accounting enable Description The radius accunting enable command is
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 88
    server as 10.20.1.100: TP-LINK(config)# radius accounting primary-ip 10.20.1.100 radius accounting secondary-ip Description The radius accounting secondary-ip command is used to configure the IP address of the alternate accounting server. To restore to the default configuration, please use no radius
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 89
    . The default port is 1813. Command Mode Global Configuration Mode Example Set the UDP port of accounting server(s) as 1816: TP-LINK(config)# radius accounting port 1816 radius accounting key Description The radius accounting key command is used to configure the shared password for the switch and
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 90
    Mode Example Configure the shared password for the switch and the accounting servers as tplink: TP-LINK(config)# radius accounting key tplink radius response-timeout Description The radius response-timeout command is used to configure the maximum time for the switch to wait for the response
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 91
    .X. Syntax show dot1x interface [ ethernet port-num ] Parameter port-num --The number of the Ethernet port. Display the configuration of all the ports ,by default. Command Mode Any configurartion Mode Example Display the port configuration of 801.X: TP-LINK(config)# show dot1x interface show radius
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 92
    Any configuration Mode Example Display the configuration of the RADIUS authentication server: TP-LINK(config)# show radius authentication show radius accounting Description The show radius accounting command is used to display the configuration of the accounting server. Syntax show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 93
    be got by show logging buffer command. It will be lost when the switch is restarted. Syntax logging local buffer {level} [ disable | enable ] buffer. By default, it is enabled. Command Mode Global Configuration Mode Example Enable the log buffer function and set the severity as 6: TP-LINK(config)#
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 94
    log. The inforamtion in the log file will not be lost after the switch is restarted and can be got by the show logging flash command. Syntax logging . By default, it is enabled. Command Mode Global Configuration Mode Example Enable the log file function and set the severity as 7: TP-LINK(config)#
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 95
    } Parameter idx --The index of the log host. The switch supports 4 log hosts. host-ip -- The IP for the log host. level --The severity level of the default, it is disabled. Command Mode Global Configuration Mode Example Enable the log host 2 and set the IP address 192.168.0.148, the level 5: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 96
    host whose configuration will be displayed. Display the configuration of all the log hosts by default. Command Mode Any Configuration Mode Example Display the configuration of the log host 2: TP-LINK(config)# show logging loghost 2 show logging buffer level Description The show logging buffer level
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 97
    severity level value. Display all the log information in the log buffer by default. Command Mode Any Configuration Mode Example Display the log information from level 0 to level 5 in the log buffer: TP-LINK(config)# show logging buffer level 5 show logging flash level Description The show logging
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 98
    no ssh server enable command. Syntax ssh server enable no ssh server enable Command Mode Global Configuration Mode Example Enable the SSH function: TP-LINK(config)# ssh server enable ssh version Description The ssh version command is used to enable the SSH protocol version. To disable the protocol
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 99
    TP-LINK(config)# ssh version v2 ssh idle-timeout Description The ssh idle-timeout command is used to specify the idle-timeout time of SSH. To restore to the factory defaults, please use no ssh idle-timeout command. Syntax ssh idle-timeout value no ssh idle-timeout Parameter value - - The Idle-
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 100
    Mode Global Configuration Mode Example Download a SSH-1 type key file named ssh-key from TFTP server with the IP Address 192.168.0.148: TP-LINK(config)# ssh download v1 ssh-key ip-address 192.168.0.148 show ssh Description The show ssh command is used to display the global configuration of SSH
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 101
    corresponding private key. By default the switch has a certificate ( self TP-LINK(config)# ssl enable ssl download certificate Description The ssl download certificate command is used to download a certificate to the switch from from TFTP server. Syntax ssl download certificate ssl-cert ip-address ip
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 102
    with the IP Address of 192.168.0.148: TP-LINK(config)# ssl download certificate ssl-cert ip-address 192.168.0.148 ssl download key Description The ssl download key command is used to download a SSL key to the switch from TFTP server. Syntax ssl download key ssl-key ip-address ip-addr Parameter
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 103
    Display the global configuration of SSL: TP-LINK(config)# show ssl 90
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 104
    , the learned MAC address will be out of the influence of the aging time and can only be deleted manually too. However, the learned entries will be saved even the switch is rebooted. status -- Enable or disable the Port Security function for a specified port. By default, this function is disabled
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 105
    specify the maximum number of MAC addresses that can be learned on this port as 30: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# bridge address port-security max-number 30 mode static status enable bridge address static Description The bridge address static command is used to add the
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 106
    , the Auto Aging function is disabled. By default, this value is 300. Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds: TP-LINK(config)# bridge aging-time 500 bridge address filtering Description The bridge address filtering command is used to add the filtering
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 107
    [port-num] Parameter port-num -- The port number of the switch. By default, the Port Security configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the Port Security configuration of port2: TP-LINK(config)# show bridge port-security 2 show bridge address
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 108
    show bridge aging-time Description The show bridge aging-time command is used to display the Aging Time of the MAC address. Syntax show bridge aging-time Command Mode Any Configuration Mode Example Display the Aging Time of the MAC address: TP-LINK(config)# show bridge aging-time 95
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 109
    default, it is empty. Command Mode Global Configuration Mode Example Configure the System Contact as www.tp-link.com.cn: TP-LINK(config)# system-descript contact-info www.tp-link.com.cn system-time gmt Description The system-time gmt command is used to configure the time zone and the IP Address for
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 110
    . Backup-ntp-server -- The IP Address for the Secondary NTP Server. Command Mode Global Configuration Mode Example Configure the system time mode as gmt, the time zone is -12, the primary ntp server is 133.100.9.2 and the secondary ntp server is 139.78.100.163: TP-LINK(config)# system-time gmt -12
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 111
    . TP-LINK(config)# system-time dst 04/01 0 11/01 23 ip address Description The ip address command is used to configure the IP Address, Subnet Mask and Default Gateway. To restore to the factory defaults, please use no ip address command. Syntax ip address {ip-addr} {ip-mask} [gateway] no ip address
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 112
    is enabled, the switch will obtain IP from DHCP Client server. Syntax ip dhcp-alloc Command Mode Global Configuration Mode Example Enable the DHCP Client function: TP-LINK(config)# ip dhcp-alloc ip bootp-alloc Description The ip bootp-alloc command is used to obtain IP address from BOOTP Server
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 113
    BOOTP Protocol to obtain IP address from BOOTP Server: TP-LINK(config)# ip bootp-alloc reset Description The reset command is used to reset the switch's software. After resetting, all configuration of the switch (except the IP Address) will restore to the factory defaults and your current settings
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 114
    this file config.cfg: TP-LINK# user-config backup filename config.cfg ip-address 192.168.0.148 user-config load Description The user-config load command is used to download the configuration file to the switch by TFTP server. Syntax user-config load filename name ip-address ip-addr Parameter name
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 115
    name ip-address ip-addr Parameter name -- Specify the name for the Firmware File. ip-addr -- IP Address of the TFTP server. Command Mode Privileged EXEC Mode Example Upgrade the switch system via the TFTP server with the IP 192.168.0.148: TP-LINK# firmware upgrade filename firmware.bin ip-address
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 116
    between the switch and one node of the network. Syntax ping {ip_addr} [-n {count}] [-l {count}] [-i {count}] Parameter ip_addr -- The IP address of the destination node for ping test. count (-n) -- The amount of times to send test data during Ping testing. It ranges from 1 to 10. By default, this
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 117
    with the IP 192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: TP-LINK# tracert 192.168.0.131 20 loopback Description The loopback command is used to test whether the port is available
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 118
    Any Configuration Mode Example Display the system information: TP-LINK# show system-info show ip address Description The show ip address command is used to display MAC Address, IP Address, Subnet Mask and Default Gateway of the system, whether the DHCP Client function is enabled or not and some
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 119
    show system-time dst Description The show system-time dst command is used to display the DST time information of the switch. Syntax show system-time dst Command Mode Any Configuration Mode Example Display the DST time information of the switch TP-LINK# show system-time dst 106
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 120
    Syntax interface ethernet interface Parameter interface -- The Ethernet port to be configured. Command Mode Global Configuration Mode Example Enter the Interface Configuration Mode and configure Ethernet port2: TP-LINK(config)# interface ethernet 2 interface range ethernet Description The interface
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 121
    , ranging from 1 to 16 characters. Command Mode Interface Configuration Mode（interface ethernet） Example Add a description Port #5 to port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# description Port #5 shutdown Description The shutdown command is used to disable an Ethernet
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 122
    the flow-control function for Ethernet port 5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# flow-control negotiation Description The negotiation command is used to configure the Negotiation Mode for an Ethernet port. To return to the default configuration, please use no negotiation
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 123
    )# interface ethernet 5 TP-LINK(config-if)# negotiation 100f storm-control Description The storm-control command is used to configure the Storm Control function. To disable the Storm Control function, please use no storm-control command. Storm Control function allows the switch to filter broadcast
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 124
    Enable the Storm Control function for port5 and specify the bc-rate as 128kbps, mc-rate as 512kbps and ul-rate as 2Mbps: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control bc-rate 128k mc-rate 512k ul-rate 2m storm-control disable bc-rate Description The storm-control disable
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 125
    Mode（interface ethernet / interface range ethernet） Example Disable the UL-Frame control for port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# storm-control disable ul-rate port rate-limit Description The port rate-limit command is used to configure the Rate Limit for an Ethernet
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 126
    ethernet / interface range ethernet） Example Disable the ingress-rate limit for port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# port rate-limit disable ingress port rate-limit disable egress Description The port rate-limit disable egress command is used to disable the egress-rate
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 127
    [interface] } Parameter Interface -- The port selected to display the connective-status. By default, the connective-status of all ports is displayed. Command Mode Any Configuration Mode Example Display the connective-status of all Ethernet ports: TP-LINK(config)# show interface status ethernet show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 128
    [port] Parameter port -- The port-number of the port selected to display the storm-control information. By default, the storm-control information of all ports is displayed. Command Mode Any Configuration Mode Example Display the storm-control information of all Ethernet ports: TP-LINK(config
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 129
    port - - The port-number of the port selected to display the rate-limit information. By default, the rate-limit information of all ports is displayed. Command Mode Any Configuration Mode Example Display the rate-limit information of all Ethernet ports: TP-LINK(config)# show port rate-limit 116
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 130
    Configure the priority of port 5 as 3: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# qos 3 qos dot1p config Description The qos dot1p config command is used to configure the mapping relation between IEEE 802.1P Priority and Egress Queue. To return to the default configuration, please use
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 131
    are mapped based on port priority mode. Syntax qos default, the mapping relation between tag and the egress queue is: 0-TC1, 1-TC0, 2-TC0, 3-TC1, 4-TC2, 5-TC2, 6-TC3, 7-TC3 2. Among the priority levels TC0-TC3, the bigger value, the higher p r i o r i t y. Example Map tag value 0 to TC3: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 132
    TP-LINK(config)# qos dscp enable qos dscp config Description The qos dscp config command is used to configure the mapping relation between DSCP Priority and 802.1P Priority. To return to the default is enabled; the untagged non-IP datagram are mapped based on port priority mode. Syntax qos dscp
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 133
    configure the Schedule Mode. To return to the default configuration, please use no qos scheduler command. When +wrr -- Strict-Priority + Weight Round Robin Mode. In this mode, the switch provides two scheduling groups, SP group and WRR group. Queues in SP group TP-LINK(config)# qos scheduler wrr 120
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 134
    -num] Parameter interface-num -- The Ethernet port selected to display the configuration. By default, information of all the ports is displayed. Command Mode Any Configuration Mode Example Display the configuration of QoS for port 5: TP-LINK# show qos port-based 5 show qos dot1p Description The show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 135
    show qos dscp Command Mode Any Configuration Mode Example Display the configuration of DSCP Priority: TP-LINK# show qos dscp show qos scheduler Description The show qos scheduler command is used to display the schedule rule of the egress queues. Syntax show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 136
    group. Command Mode Global Configuration Mode Example Configure port 3 as mirrored port, port 4 as mirroring port, the mirror mode as both and group number as 1 : TP-LINK(config)# mirror add 3 4 both 1 User Guidelines 1. The mirroring port is corresponding to current interface configuration mode
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 137
    group. Syntax mirror remove mirrored [mirrored port] [group-num] Parameter Mirrored port -- The port to be monitored. group-num -- The group number of mirrior group. Command Mode Global Configuration Mode Example Remove mirrored port 1,2-4 from mirror group 1: TP-LINK(config)# mirror remove mirrored
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 138
    . Syntax show mirror [group-num] Parameter group-num -- The group number of mirrior group. Command Mode Any Configuration Mode Example Display configuration fo mirror group 1: TP-LINK# show mirror 1 125
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 139
    packets to port 6 and port 10: TP-LINK(config)# interface range ethernet 1-2 TP-LINK(config-if)# port isolation 6,10 show port isolation Description The show port isolation command is used to display the forward portlist of a port. Syntax show port isolation [port] Parameter port -- The port-number
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 140
    Example Display the forward-list of port 6: TP-LINK# show port isolation 6 127
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 141
    24 PoE Commands PoE (Power over Ethernet) technology describes a system to transmit electrical power along with data to remote devices over standard twisted-pair cable in an Ethernet network. It is especially useful for supplying power to IP power the PoE switch can supply as 160W: TP-LINK(config)#
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 142
    power inline supply status {enable|disable} Parameter status -- the PoE status of the corresponding port. Command Mode Interface Configuration Mode Example Enable the PoE feature for port 2.: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# power inline supply status enable power inline
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 143
    Interface Configuration Mode Example Enable the PoE priority as low for port 2.: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# power inline priority low power inline consumption (interface configuration) Description The power inline consumption (interface configuration) command is used
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 144
    Configuration Mode Example Select the File2 as the time range for port 2.: TP-LINK(config)# interface ethernet 2 TP-LINK(config-if)# power inline profile File2 power profile Description The power profile command is used to create a PoE profile. no power profile is used to remove the configured
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 145
    port in the profile can supply. Command Mode Interface Configuration Mode Example Create a PoE profile. Profile name is File2, PoE feature is enabled, PoE priority is low and the power limit is 5W. TP-LINK(config)# interface ethernet 2 TP-LINK off-day, working-day. 1-3,6 represent Monday, Tuesday,
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 146
    the switch supplies power in the holiday or not. By default, the holiday is exluded. time-slice -- Create a time-slice, in the format of HH:MM-HH:MM. Command Mode Global Configuration Mode Example Add a time-range named tSeg1, with time-slice1 from 8:30 to 12:00 at working day: TP-LINK(config
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 147
    display the PoE configuration of the certain port. Syntax show power inline configuration [ethernet port] Parameter port -- The port selected to display the PoE configuration, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the PoE configuration of all ports: TP-LINK> show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 148
    to display the PoE information of the certain port. Syntax show power inline information [ethernet port] Parameter port -- The port selected to display the PoE information, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the PoE information of all ports: TP-LINK> show power
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 149
    Display the defined holiday: TP-LINK> show power holiday show power profile Description The show power profile command is used to display the defined PoE profile. Syntax show power profile Command Mode Any Configuration Mode Example Display the defined PoE profile: TP-LINK> show power profile 136
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 150
    Wednesday and Saturday; daily represents every day; off-day represents weekend and working-day represents working day. By default, the period mode is disabled. start-date - - The start date in Absoluteness Mode, in the format of MM/DD/YYYY. By default, it is 01/01/2000. end-date - - The end date in
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 151
    Enable/ Disable Holiday Mode. By default, it is disabled. time-slice -- Create a time-slice, in the format of HH:MM-HH:MM. Command Mode Global Configuration Mode Example Edit the time-range named tSeg1, with time-slice1 from 8:30 to 12:00 at working day: TP-LINK(config)# acl edit time-segment tSeg1
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 152
    , configuring the start date as October 1st, and the end date as October 3rd: TP-LINK(config)# acl holiday NationalDay 10/01 10/03 acl create Description The acl create command be MAC ACL, 100-199 must be Standard-IP ACL, and 200-299 must be Extend-IP ACL. Command Mode Global Configuration Mode 139
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 153
    is 20: TP-LINK(config)# acl . rule-id -- The rule ID. op -- The operation for the switch to process packets which match the rules. There are two options, discard default, the option is permit. source-mac -- The source MAC address contained in the rule. source-mac-mask -- The source MAC address
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 154
    :16:23, the source MAC address mask is 11:11:11:11:11:00, VLAN ID is 2, the user priority is 5, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl create 20 TP-LINK(config)# acl rule mac
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 155
    :3F:48:16:23, the source MAC address mask is 11:11:11:11:11:00, VLAN ID is 2, the user priority is 5, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl edit rule mac-acl
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 156
    it. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl create 120 TP-LINK(config)# acl rule std-acl 120 10
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 157
    ID is 120. In the rule, the source IP address is 192.168.0.100, the source IP address mask is 255.255.255.0, the time-range for the rule to take effect is tSeg1, and the packets match this rule will be forwarded by the switch: TP-LINK(config)# acl edit rule std-acl 120 10 op
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 158
    TP-LINK acl-id} [rate rate] [osd { none | discard }] [e-port egress-port] [dscp dscp] [pri local-pri] [mirr mirror] no to the specific port. The destination port ranges from 1 to 8. By default, it is All Ports. dscp to 3. mirror -- The Mirror Port of Stream Mirror. By default, it is 1. Command Mode
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 159
    . mirror -- The Mirror Port of Stream Mirror. By default, it is 1. Command Mode Global Configuration Mode Example Edit the actions for the policy1. For the data packets that match ACL 120 in the policy, if the rate beyond 1000kbps, will be discarded by the switch: TP-LINK(config)# acl edit action
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 160
    } Parameter policy-name -- The name of the policy desired to bind. port -- The number of the port desired to bind. Command Mode Global Configuration Mode Example Bind policy1 to Port 1,3-5: TP-LINK(config)# acl bind to-port policy1 1,3-5 acl bind to-vlan Description The acl bind to-vlan command is
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 161
    acl holiday command is used to display the defined holiday. Syntax show acl holiday Command Mode Any Configuration Mode Example Display the defined holiday: TP-LINK> show acl holiday show acl config Description The show acl config command is used to display the configuration of ACL. Syntax show acl
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 162
    show acl bind Description The show acl bind command is used to display the configuration of Policy bind. Syntax show acl bind Command Mode Any Configuration Mode Example Display the configuration of Policy bind: TP-LINK> show acl bind 149
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 163
    is the interval to send BPDU packets, and used to test the links. Hello Time ranges from 1 to10 in seconds and it is 2 by default. Otherwise, 2 * (Hello Time + 1)
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 164
    . By default, it is 20. Command Mode Global Configuration Mode Example Enable the STP function, and configure the STP version as MSTP, CIST priority as 4096, Hello Time as 4 seconds, Max Age as 10 seconds, Forward Delay as 10 seconds, TxHold Count as 8pps and Max Hops as 15 hops: TP-LINK(config
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 165
    and then enable Edge Port: TP-LINK(config)# interface ethernet 1 TP-LINK(config-if)# spanning-tree common-config status enable pri 64 expath 100 inpath 100 edge enable spanning-tree region Description The spanning-tree region command is used to configure the region of MSTP. A switched network can be
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 166
    -- MSTI Priority, which must be multiple of 4096 ranging from 0 to 61440. By default, it is 32768. MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance. mapped -- VLAN-Instance mapping. Enter the VLAN ID which belongs to the
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 167
    MSTI Priority as 4096: TP-LINK(config)# spanning-tree msti 1 status enable pri 4096 mapped 2-5,8 spanning-tree msti Description The spanning-tree msti command is used to configure MSTP Instance Port. To return to the default configuration of the corresponding Instance Port, please use no spanning
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 168
    TC-BPDUs received by the switch in a TC Protect Cycle. period -- TC Protect Cycle, ranging from 1 to 10 in seconds. By default, it is 5. Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets, and TC Protect Cycle as 10 seconds: TP-LINK(config)# spanning-tree tc-defend
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 169
    . By default, it is disabled. BPDU Filter is to prevent BPDUs flood in the STP network. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable Loop Protect, Root Protect, TC Protect, BPDU Protect, and BPDU Filter for port 2: TP-LINK(config)# interface
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 170
    of Spanning Tree: TP-LINK# show spanning-tree global-config show spanning-tree port-config Description The show spanning-tree port-config command is used to display the Port configuration of Spanning Tree. Syntax show spanning-tree port-config [port] Parameter port - - The port selected to display
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 171
    Display the configuration of port 5: TP-LINK(config)# show spanning-tree port-config 5 show spanning-tree region Description The show spanning-tree region command is used to display the Region configuration of MSTP. Syntax show spanning-tree
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 172
    tree msti port {id} [port] Parameter id -- Instance ID, ranging from 1 to 8. port - - The port selected to display the configuration. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the configuration of port 5 in Instance 1: TP-LINK(config
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 173
    port -- The port selected to display the configuration. By default, the Port Protect configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the Port Protect configuration of port 2: TP-LINK(config)# show spanning-tree security port-defend 2 160
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 174
    switch. By default, it is disabled. unknown-packet - - The operation for the switch to process unknown multicast, with pass and discard options. Command Mode Global Configuration Mode Example Enable IGMP Snooping function, and specify the operation to process unknown multicast as discard: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 175
    for a port, the switch will immediately remove this port from the multicast group upon receiving IGMP leave messages. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable IGMP Snooping and Fast Leave function for port 5: TP-LINK(config)# interface
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 176
    Mode Global Configuration Mode Example Enable IGMP Snooping for VLAN 1, and configure Router Port Time as 200 seconds, Member Port Time as 100 seconds, Leave time as 10 seconds and Static Router Port as port 1: TP-LINK(config)# igmp-snooping vlan-config-add 1 rtime 200 mtime 100 ltime 10 rport
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 177
    . By default, it is 1. router-port -- Static Router Port, which is mainly used in the network with stable topology. Command Mode Global Configuration Mode Example Modify Router Port Time as 300 seconds, Member Port Time as 200 seconds, and Leave time as 15 seconds for VLAN 1: TP-LINK(config)# igmp
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 178
    255. Syntax igmp-snooping static-entry-add {ip} {vlan-id} {switch-port} no igmp-snooping static-entry-add {ip} {vlan-id} Parameter ip -- The static multicast IP address. vlan-id -- The VLAN ID of the multicast IP, ranging from 1 to 4094. switch-port -- The forward port of the multicast group, in the
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 179
    configure the forward port as port 1: TP-LINK(config)# igmp-snooping static-entry-add 225.0.0.1 2 1 igmp-snooping filter-add Description The igmp-snooping filter-add command is used to configure the multicast IP-range desired to filter. To delete the corresponding IP-range, please use no igmp-
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 180
    10~225.0.0.12: TP-LINK(config)# igmp-snooping filter-config 20 225.0.0.10 225.0.0.12 igmp-snooping filter Description The igmp-snooping filter command is used to configure Port Filter. To return to the default configuration, please use no igmp-snooping filter command. When the switch receives IGMP
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 181
    range ethernet） Example Enable multicast filtering function for port 5, specify Action Mode as accept, bound IP-range 2, 3, 4, and specify the maximum number of multicast groups for port 5 to join in as 128: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# igmp-snooping filter status enable
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 182
    Example Display the IGMP configuration of port 2: TP-LINK> show igmp-snooping port-config 2 show igmp-snooping vlan-config Multicast VLAN configuration: TP-LINK> show igmp-snooping multi-vlan show igmp-snooping multi-ip-list Description The show igmp-snooping multi-ip-list command is used
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 183
    IP-Range table: TP-LINK(config)# show igmp-snooping filter-ip-addr show igmp-snooping port-filter Description The show igmp-snooping port-filter command is used to display the configuration of Multicast Port Filter. Syntax show igmp-snooping port-filter [port-num] Parameter port-num -- The port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 184
    packet-stat command is used to display the Packet Statistics information of all ports. Syntax show igmp-snooping packet-stat Command Mode Any Configuration Mode Example Display the Packet Statistics information: TP-LINK> show igmp-snooping packet-stat show igmp-snooping packet-stat-clear Description
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 185
    SNMP function. By default, it is switch. Its length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile. Command Mode Global Configuration Mode Example Enable the SNMP function, and specify the Local Engine ID as 1234567890, the Remote Engine ID as 123456abcdef: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 186
    Identifier) of the SNMP packets is used to describe the managed objects of the switch, and the MIB (Management Information Base) is the set of the OIDs. , and this OID can be managed by the SNMP management station: TP-LINK(config)# snmp view-add view1 1.3.6.1.6.3.20 include snmp group-add Description
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 187
    USM mechanism. By default, the Security Model is Switch's SNMP agent. Command Mode Global Configuration mode Example Add group 1, configure its Security Model as SNMP v2c, view1 can be read and edited by group member, and the trap messages sent by view2 can be received by Management station: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 188
    User in a SNMP Group can manage the switch via the management station software. The User port authentication is performed via SHA (Secure Hash Algorithm). SHA authentication mode has a higher security than MD5 mode. By default, the Authentication Mode is none. confirm-pwd -- Authentication Password
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 189
    encryption method is used. By default, the Privacy Mode is none. encrypt-pwd -- Privacy Password, ranging from 1 to 16 Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: TP-LINK(config)# snmp user-add admin local group2 smode
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 190
    the Notification function enabled, the switch can initiatively report to the management ip} {user-name} Parameter ip -- The IP Address of the management Host. udp-port -- UDP port, which is used to send notifications. The UDP port functions with the IP address for the notification sending. By default
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 191
    entry, and configure the IP Address of the management Host as 192.168.0.1, the UDP port as 162, the User name of the management station as admin, the Security Model of the management station as v2c, the type of the notifications as inform, the maximum time for the switch to wait as 1000 seconds
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 192
    . owner -- The owner of the history sample entry, ranging from 1 to 16 characters. By default, it is monitor. Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner1: TP-LINK(config)# snmp-rmon history owner 1 owner1 snmp-rmon history enable Description The snmp-rmon
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 193
    of the User to which the event belongs, ranging from 1 to 16 characters. By default, it is public. Command Mode Global Configuration Mode Example Configure the user name of entry 1 as user1: TP-LINK(config)# snmp-rmon event user 1 user1 snmp-rmon event description Description The snmp-rmon event
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 194
    description -- The description of the event, ranging from 1 to 16 characters. By default, it is empty. Command Mode Global Configuration Mode Example Configure the description of entry 1 as description1: TP-LINK(config)# snmp-rmon event description 1 description1 snmp-rmon event type Description The
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 195
    command. owner -- The owner of the event entry, ranging from 1 to 16 characters. By default, it is monitor. Command Mode Global Configuration Mode Example Configure the owner of entry 1 as owner1: TP-LINK(config)# snmp-rmon event owner 1 owner1 snmp-rmon event enable Description The snmp-rmon event
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 196
    Enable the SNMP-RMON Event entries 1,2,3,4 and 8: TP-LINK(config)# snmp-rmon event enable 1-4,8 snmp-rmon alarm config Description The snmp-rmon alarm config command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no snmp-rmon alarm config command.
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 197
    -- The alarm interval time, ranging from 10 to 3600 in seconds. By default, it is 1800. Command Mode Global Configuration Mode Example Configure the alarm interval time of the entries 1,2,3 and 6 as 1000 seconds: TP-LINK(config)# snmp-rmon alarm config 1-3,6 interval 1000 snmp-rmon alarm owner
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 198
    to enable, ranging from 1 to 12, in the format of 1-3,5. Command Mode Global Configuration Mode Example Enable the Alarm Management entries 1,2,3,4 and 8: TP-LINK(config)# snmp-rmon alarm enable 1-4,8 show snmp global-config Description The show snmp global-config command is used to display SNMP
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 199
    show snmp view command is used to display the View table. Syntax show snmp view Command Mode Any Configuration Mode Example Display the View table: TP-LINK> show snmp view show snmp group Description The show snmp group command is used to display the Group table. Syntax show snmp group Command Mode
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 200
    is used to display the Notification table. Syntax show snmp destination-host Command Mode Any Configuration Mode Example Display the Notification table: TP-LINK> show snmp destination-host show snmp-rmon history Description The show snmp-rmon history command is used to display the configuration of
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 201
    from 1 to 12. You can only select one entry for each command. By default, the configuration of all entries is displayed. Command Mode Any Configuration Mode Example Display the Event configuration of entry 2: TP-LINK> show snmp-rmon event 2 show snmp-rmon alarm Description The show snmp-rmon alarm
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 202
    ranging from 1 to 12. You can only select one entry for each command. By default, the configuration of all entries is displayed. Command Mode Any Configuration Mode Example Display the configuration of all Alarm Management entries: TP-LINK> show snmp-rmon alarm 189
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 203
    is used to enable LLDP function. To return to the default configuration, please use no lldp enable command. Syntax lldp enable no lldp enable Command Mode Global Configuration Mode Example Enable lldp function globally: TP-LINK(config)# lldp enable lldp hold-multiplier Description The lldp hold
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 204
    TP-LINK(config)# lldp hold-multiplier 5 lldp timer Description The lldp timer command is used to configure the parameters about transmission. To return to the default LLDPDU to its neighbors. By default, it is 30 seconds. tx sent frequently. By default, it is 2 attempted. The default value is 3.
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 205
    med-fast-count count no lldp med-fast-count Parameter count -- Configure the Fast Start Count parameter. It ranges from 1 to 10. By default, it is 4. Command Mode Global Configuration Mode Example Specify Fast Start Count as 5: TP-LINK(config)# lldp med-fast-count 5 lldp admin-status Description 192
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 206
    receive LLDP frames. By default, the LLDP operating mode of all ports is "txrx". Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Configure the LLDP operating mode as "tx" for port 6: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# lldp admin
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 207
    Mode（interface ethernet / interface range ethernet） Example Exclude "management-address" and "port-vlan-id" TLVs in LLDPDU outgoing from port 8: TP-LINK(config)# interface ethernet 8 TP-LINK(config-if)# no lldp tlv-select management-address port-vlan-id lldp med-status Description The lldp med
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 208
    status for port 6: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# lldp med-status enable lldp med-tlv-select Description The lldp med-tlv-select command is used to configure TLVs to be included in outgoing LLDPDU. To exclude TLVs, please use no lldp med-tlv-select command. By default, All
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 209
    in the Location Identification TLV's content in outgoing LLDPDU of port 6. Configure the language as Enlish and city as London: TP-LINK(config)# interface ethernet 6 TP-LINK(config-if)# lldp med-location civic-address language English city London show lldp global Description The show lldp global
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 210
    the LLDP information of the certain port. Syntax show lldp local-information [port] Parameter port -- The port selected to display the information of LLDP, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the LLDP information of port 8: TP-LINK> show lldp local-information
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 211
    neighbor device of the certain port. Syntax show lldp statistics [port] Parameter port -- The port selected to display the neighbor information, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the LLDP statistic information of port 8: TP-LINK> show lldp statistics 8 show
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 212
    configuration of the certain port. Syntax show lldp med interface [ethernet port] Parameter port -- The port selected to display the configuration of LLDP, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the LLDP-MED configuration of port 8: TP-LINK> show lldp med interface
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 213
    information of the certain port. Syntax show lldp med neighbor-information [port] Parameter port -- The port selected to display the neighbor information, ranging from 1 to 24. Command Mode Any Configuration Mode Example Display the LLDP-MED information of port 8's neighbor: TP-LINK> show lldp med
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 214
    After a commander switch is configured, management directly connected neighbor devices to support cluster establishing. An NDP- default, it is 60. Command Mode Global Configuration Mode Example Enable NDP function globally, and configure Aging Time as 120 seconds, Hello Time as 50 seconds: TP-LINK
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 215
    . To return to the default configuration, please use no cluster ntdp command. NTDP (Neighbor Topology Discovery Protocol) is used to collect the NDP information and neighboring connection information of each device in a specific network range. It provides the commander switch with the information of
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 216
    -- Enable/ Disable NTDP function for the port. By default, it is enabled. Command Mode Interface Configuration Mode（interface ethernet / interface range ethernet） Example Enable NDP and NTDP function for port 5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# cluster ndp enable ntdp enable
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 217
    with the current role. The conversion between Candidate Switch and Individual Switch is: Candidate Switch Ù Individual Switch. Command Mode Global Configuration Mode Example Change the role of the current switch to Candidate Switch: TP-LINK(config)# cluster manage role-change candidate show cluster
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 218
    of the certain port. Syntax show cluster ndp port-status [port] Parameter port -- The port selected to display the configuration of NDP. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the NDP configuration of port 2: TP-LINK> show cluster
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 219
    port. Syntax show cluster ntdp port-status [port] Parameter port -- The port selected to display the configuration of NTDP. By default, the configuration of all ports is displayed. Command Mode Any Configuration Mode Example Display the NTDP configuration of port 2: TP-LINK> show cluster ntdp port
  • TP-Link TL-SG3424P | TL-SG3424P V1 CLI Guide - Page 220
    cluster ntdp device show cluster manage role Description The show cluster manage role command is used to display the role of the current switch. Syntax show cluster manage role Command Mode Any Configuration Mode Example Display the role of the current switch: TP-LINK> show cluster manage role 207
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
TL-SG3424P
JetStream L2 Managed PoE Switch
Rev: 1.0.0
1910010613