TP-Link TL-WA5110G User Guide - Page 60

Static Routing

Get TP-Link TL-WA5110G PDF manuals and user guides
UPC - 845973051327
View all TP-Link TL-WA5110G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

router. ¾ Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LAN port. The default value is disabled. If enabled, the ping packet from the LAN port cannot access the router. (Defends against some viruses) Click the Save button to save the settings. Click the Blocked DoS Host Table button to display the DoS host table by blocking. 4.11 Static Routing A static route is a pre-determined path that network information must travel to reach a specific host or network. To add or delete a route, work in the area under the Static Routing page as shown in Figure 4-44. Figure 4-44 Static Routing To add static routing entries: 1. Click the Add New button. (pop up Figure 4-45) 2. Enter the following parameters. ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. ¾ Default Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host. 3. Select Enabled or Disabled for this entry from the Status pull-down list. 4. Click the Save button to save the changes. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
52
router.
¾
Forbid Ping Packet from LAN Port
-
Enable or Disable forbidding Ping Packet to access
the router from the LAN port. The default value is disabled. If enabled, the ping packet from
the LAN port cannot access the router. (Defends against some viruses)
Click the
Save
button to save the settings.
Click the
Blocked DoS Host Table
button to display the DoS host table by blocking.
4.11 Static Routing
A static route is a pre-determined path that network information must travel to reach a specific
host or network. To add or delete a route, work in the area under the Static Routing page as
shown in Figure 4-44.
Figure 4-44 Static Routing
To add static routing entries:
1.
Click the
Add New
button. (pop up Figure 4-45)
2.
Enter the following parameters.
¾
Destination IP Address
-
The
Destination IP Address
is the address of the network or host
that you want to assign to a static route.
¾
Subnet Mask
-
The
Subnet Mask
determines which portion of an IP Address is the network
portion, and which portion is the host portion.
¾
Default Gateway
-
This is the IP Address of the gateway device that allows for contact
between the router and the network or host.
3.
Select
Enabled
or
Disabled
for this entry from the
Status
pull-down list.
4.
Click the
Save
button to save the changes.