TP-Link TL-WA5110G User Guide - Page 71

Reboot

Get TP-Link TL-WA5110G PDF manuals and user guides
UPC - 845973051327
View all TP-Link TL-WA5110G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Figure 4-60 Speed Test ¾ Destination IP - The Remote device's IP address. ¾ User - Administrator password of the remote device. It should be filled correctly if you want to get a precise estimation. Otherwise, keep it clean. ¾ Advanced options - This is a switch to show advanced test options which are used only for precise estimation. ) Note: If either User or Password is incorrect, we will take a basic test instead. In other words, none of the advance options you set will take effect. ¾ Direction - There are 3 options available for the traffic direction while estimating the throughput. z transmit - Estimate the outgoing throughput (TX). z receive - Estimate the ingoing throughput (RX). z both - Estimate the incoming (RX) first and then the outgoing (TX) afterwards. ¾ Duration - The value you specify here indicate how much time the test should last. ¾ Data amount - The maximal data amount to be sent out during the whole test. ) Note: If both Duration and Data amount are specified, the test will stop after any of them is met. Be sure to click the Run Test button to start a new test after you filled enough information. You can also stop a running test by click Stop Test button at any time. 4.14.7 Reboot Selecting System Tools > Reboot allows you to reboot the device on the screen shown in Figure 4-61. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
63
Figure 4-60 Speed Test
¾
Destination IP
-
The Remote device’s IP address.
¾
User
-
Administrator password of the remote device. It should be filled correctly if you want to
get a precise estimation. Otherwise, keep it clean.
¾
Advanced options
-
This is a switch to show advanced test options which are used only for
precise estimation.
)
Note:
If either User or Password is incorrect, we will take a basic test instead. In other words, none of
the advance options you set will take effect.
¾
Direction
-
There are 3 options available for the traffic direction while estimating the
throughput.
z
transmit
- Estimate the outgoing throughput (TX).
z
receive
- Estimate the ingoing throughput (RX).
z
both
- Estimate the incoming (RX) first and then the outgoing (TX) afterwards.
¾
Duration
-
The value you specify here indicate how much time the test should last.
¾
Data amount
-
The maximal data amount to be sent out during the whole test.
)
Note:
If both Duration and Data amount are specified, the test will stop after any of them is met.
Be sure to click the
Run Test
button to start a new test after you filled enough information. You
can also stop a running test by click Stop Test button at any time.
4.14.7
Reboot
Selecting
System Tools
>
Reboot
allows you to reboot the device on the screen shown in Figure
4-61.