TP-Link TL-WA7210N User Guide

TP-Link TL-WA7210N Manual

Get TP-Link TL-WA7210N PDF manuals and user guides View all TP-Link TL-WA7210N manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-WA7210N manual content summary:

  • TP-Link TL-WA7210N | User Guide - Page 1
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point REV2.0.0 1910010786
  • TP-Link TL-WA7210N | User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link TL-WA7210N | User Guide - Page 3
    limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. "To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used
  • TP-Link TL-WA7210N | User Guide - Page 4
    Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired
  • TP-Link TL-WA7210N | User Guide - Page 5
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link TL-WA7210N | User Guide - Page 6
    TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 2.4GHz 150Mbps Outdoor Wireless Access Point Model No.: TL-WA7210N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable
  • TP-Link TL-WA7210N | User Guide - Page 7
    AP...9 2.3.7 Client...10 Chapter 3. Quick Installation Guide 11 3.1 Configure the Device...11 3.2 Quick Setup ...12 3.2.1 AP Client Router...15 3.2.2 AP Router...19 3.2.3 Access Point...23 3.2.4 Multi-SSID ...26 3.2.5 Repeater (Range Extender 28 3.2.6 Bridge with AP...32 3.2.7 Client...35 Chapter
  • TP-Link TL-WA7210N | User Guide - Page 8
    Firmware Upgrade...62 4.9.7 Factory Defaults ...63 4.9.8 Backup & Restore...63 4.9.9 Reboot ...64 4.9.10 Password ...64 4.9.11 System log...65 4.9.12 Statistics...66 Chapter 5. AP Client Router & AP Router Operation Mode 68 5.1 Login ...68 5.2 Status ...68 5.3 Quick Setup ...70 5.4 Operation Mode
  • TP-Link TL-WA7210N | User Guide - Page 9
    Antenna Alignment ...92 5.7.6 Distance Setting ...92 5.7.7 Throughput Monitor 93 5.7.8 Wireless Statistics...93 5.8 DHCP ...94 5.8.1 DHCP Settings Parental Control ...105 5.12 Access Control...107 5.12.1 Rule Settings...114 5.14.2 Rules List ...114 5.15 IP & MAC Binding ...115 5.15.1 Binding Setting
  • TP-Link TL-WA7210N | User Guide - Page 10
    ...120 5.17.1 Time Settings ...121 5.17.2 Diagnostic ...122 5.17.3 Firmware Upgrade 123 5.17.4 Factory Defaults ...124 5.17.5 Backup & Restore...124 5.17.6 Reboot ...125 5.17.7 Password ...125 5.17.8 System log...126 5.17.9 Statistics...128 Appendix A: FAQ...130 Appendix B: Configuring the PC 134
  • TP-Link TL-WA7210N | User Guide - Page 11
    :  One TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point  One power Adapter for TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point  One Power Injector  Mounting Kits  Quick Installation Guide  One Resource CD for TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point, including
  • TP-Link TL-WA7210N | User Guide - Page 12
    help you build a more stable link or cover more area outdoors. The TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point provides 7 operation modes for multi-user to access the Internet: AP Client Router, AP Router, Access Point, Multi-SSID, Repeater (Range Extender), Bridge with AP and Client. In
  • TP-Link TL-WA7210N | User Guide - Page 13
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Provides WLAN ACL (Access Control List).  Supports configuration backup/restore and firmware upgrade.  Supports Web management.  Supports Remote Management.  Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through. 
  • TP-Link TL-WA7210N | User Guide - Page 14
    2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 1.3 Conventions The AP or TL-WA7210N, or device mentioned in this User guide stands for TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point without any explanations. Parameters provided in the pictures are just references for setting up
  • TP-Link TL-WA7210N | User Guide - Page 15
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 1.4.2 The Rear Panel Figure 1-2 Rear Panel sketch View from left to right, the parts are explained below.  : This is where you can connect an outside antenna. For this AP, the antenna is built inside, and usually there is not
  • TP-Link TL-WA7210N | User Guide - Page 16
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Chapter 2. Connecting the Device 2.1 System Requirements  Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.  TCP/IP protocol must be installed on each PC.  Web browser, such as
  • TP-Link TL-WA7210N | User Guide - Page 17
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2.3.1 AP Client Router Mode Figure 2-1 Hardware Installation of the TL-WA7210N in AP Client Router mode 1. Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet cable. 2. Connect the PC to the LAN
  • TP-Link TL-WA7210N | User Guide - Page 18
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2.3.3 Access Point This operation mode allows wireless stations to access. Figure 2-3 Hardware Installation of the TL-WA7210N in Access Point mode 1. Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an
  • TP-Link TL-WA7210N | User Guide - Page 19
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2.3.5 Repeater and Universal Repeater Figure 2-5 Hardware Installation of the TL-WA7210N in (Universal) Repeater mode 1. Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet cable. 2. Plug one end
  • TP-Link TL-WA7210N | User Guide - Page 20
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: It is recommended that you connect a PC/notebook to the LAN port of the Device with an Ethernet cable, and then login the Device from the PC/notebook to set the Device in Bridge with AP mode. 2.3.7 Client Figure 2-7 Hardware
  • TP-Link TL-WA7210N | User Guide - Page 21
    can be found in "Chapter 4 Configuring the AP" 3.1 Configure the Device The instructions in this section will help you configure each of your PCs to be able to communicate with the AP. The default IP address of the TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point is 192.168.0.254. And the
  • TP-Link TL-WA7210N | User Guide - Page 22
    . 3.2 Quick Setup The following instructions will guide you through a few easy steps to configure your AP and connect to Internet. With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and manage the TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point. The
  • TP-Link TL-WA7210N | User Guide - Page 23
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Open your web browser and enter the IP has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the configure the AP using the Web browser. Please click the Quick Setup link on the left of the
  • TP-Link TL-WA7210N | User Guide - Page 24
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-6 Quick Setup Click Next, and then Operation Mode page will appear, shown in Figure 3-7: Figure 3-7 Operation Mode  AP Client Router - In this mode, the device enables multi-users to share Internet from WISP. The LAN port
  • TP-Link TL-WA7210N | User Guide - Page 25
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: When you change the operation mode to Client/Repeater, WPS function will stay disabled. Please manually enable this function if needed when you switch back to Access Point/Multi-SSID/Bridge mode. 3.2.1 AP Client Router When
  • TP-Link TL-WA7210N | User Guide - Page 26
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-10 WISP Station Setting  Wireless Name of WISP : Ensure you select a correct country to comply with local laws. Incorrect settings may cause interference.  Transmission Power - The available options of transmission power
  • TP-Link TL-WA7210N | User Guide - Page 27
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Wireless Security Mode - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type.  Wireless Password - If the AP your Device is
  • TP-Link TL-WA7210N | User Guide - Page 28
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-12 AP List 3. The page below will appear. Create a name for the Local Wireless Network. The security settings for the local network will be set the same as your WISP by default. Then click Next. Figure 3-13 Local Wireless AP
  • TP-Link TL-WA7210N | User Guide - Page 29
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-15 Finish page 3.2.2 AP Router When you choose AP Router Mode on Operation Mode page in Figure 3-7, take the following steps: 1. Click Next in Figure 3-7, and then WAN Connection Type page will appear as shown in Figure 3-16
  • TP-Link TL-WA7210N | User Guide - Page 30
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-17 PPPoE 2) Enter the User Name Name (SSID) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_xxxxxx (xxxxxx indicates the last unique six characters of each Device's MAC address
  • TP-Link TL-WA7210N | User Guide - Page 31
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: Ensure you select a correct country to comply with local laws. Incorrect settings MAC address of the router and not allow it to connect. However, TP-LINK router can "clone" or replicate the registered MAC address of the MAIN
  • TP-Link TL-WA7210N | User Guide - Page 32
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: It is strongly recommended to restart the Cable Modem after the Quick Setup is done. This important operation will solve most issues. 2) Choose to clone MAC address or not, if you are unsure, please select YES. Then click
  • TP-Link TL-WA7210N | User Guide - Page 33
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-21 Finish page 3.2.3 Access Point When you choose Access Point on Operation Mode page in Figure 3-7, take the following steps: 1. Click Next in Figure 3-7, and then Wireless page will appear as shown in Figure 3-22. Create
  • TP-Link TL-WA7210N | User Guide - Page 34
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide local laws. Incorrect settings may cause interference. chosen if the Security Mode is WEP. It indicates the Note: The operating distance or range of your wireless connection varies significantly Antenna in the upright position. 24
  • TP-Link TL-WA7210N | User Guide - Page 35
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Away from large metal surfaces. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Device. 2. The Network Setting page will appear then. It is recommended
  • TP-Link TL-WA7210N | User Guide - Page 36
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 3.2.4 Multi-SSID When you choose Multi-SSID on Operation Mode configuration take effect. Click Next to continue.  Note: The operating distance or range the Antenna in the supports Tag function, or this PC will not be able to access
  • TP-Link TL-WA7210N | User Guide - Page 37
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide determined by the region selected.  Wireless Security Mode - You can select one of the following configurations for the selected SSID. 2. The Network Setting page will appear then. It is recommended that you keep the default settings
  • TP-Link TL-WA7210N | User Guide - Page 38
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-26 Network 3. When you finish the wireless setting in Figure 3-26 and click Next, then Figure 3-27 will appear, where you can click Finish button to complete the Quick Setup. Figure 3-27 Finish page 3.2.5 Repeater (Range
  • TP-Link TL-WA7210N | User Guide - Page 39
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-28 Wireless  Repeater Mode - Choose mode for repeater.  WDS Repeater - In WDS Repeater mode, the AP with WDS enabled will relays data to an associated root AP. AP function is enabled meanwhile. The wireless repeater relays
  • TP-Link TL-WA7210N | User Guide - Page 40
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Note Dialog  Note: Ensure you select a correct country to comply with local laws. Incorrect settings Mode is WEP. distance or range of your wireless Antenna repeat, and then click Connect on the right side of the line. 30
  • TP-Link TL-WA7210N | User Guide - Page 41
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-29 AP List You will then return to the Wireless page as shown in Figure 3-28. The security mode will be selected automatically, please confirm it and enter the same password as is on your router or access point, then click
  • TP-Link TL-WA7210N | User Guide - Page 42
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-31 Finish page 3.2.6 Bridge with AP When you choose Bridge with AP on Operation Mode page in Figure 3-7, take the following steps: 1. Click Next in Figure 3-7, and then Wireless page will appear as shown in Figure 3-32.
  • TP-Link TL-WA7210N | User Guide - Page 43
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide to comply with local laws. Incorrect settings may cause interference.  Transmission Power problems with another nearby access point.  Wireless Security Mode - This option should be chosen according to the AP's security configuration
  • TP-Link TL-WA7210N | User Guide - Page 44
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: The operating distance or range of your wireless connection varies significantly based on the physical placement of the Device. For best results, place your Device  Near the center of the
  • TP-Link TL-WA7210N | User Guide - Page 45
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 3-35 Network 5. When you finish the wireless setting in Figure 3-35 and click Next, then Figure 3-36 will appear, where you can click Finish button to complete the Quick Setup. Figure 3-36 Finish page 3.2.7 Client When you
  • TP-Link TL-WA7210N | User Guide - Page 46
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 1. Click Next in Figure 3-7, and then Wireless page will appear as shown in Figure 3-37. to continue. Note Dialog  Note: Ensure you select a correct country to comply with local laws. Incorrect settings may cause interference. 36
  • TP-Link TL-WA7210N | User Guide - Page 47
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Transmission Power - The available options of transmission power are determined by the region selected.  Wireless Security Mode - This option should be chosen according to the AP's security configuration or range of your Antenna
  • TP-Link TL-WA7210N | User Guide - Page 48
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide You will then return to the Wireless page as shown in Figure 3-37. The security mode will be selected automatically, please confirm it and enter the same password as is on your router or access point, then click Next. 3. The Network
  • TP-Link TL-WA7210N | User Guide - Page 49
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: If the wireless connection is poor after basic configuration of operation mode, please select Wireless > Distance Setting, and set the outdoor distance value at 110% of the real distance as shown in Figure 3-41. It will help
  • TP-Link TL-WA7210N | User Guide - Page 50
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Chapter 4. AP & Multi-SSID & Repeater (Range Extender) & Bridge with AP & Client Operation Mode This Chapter describes how to configure some advanced settings for your Access Point through the web-based management page in standard AP
  • TP-Link TL-WA7210N | User Guide - Page 51
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 1. Wired This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask. 2. Wireless This field displays basic information or status for wireless function, including
  • TP-Link TL-WA7210N | User Guide - Page 52
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  AP Router - In this mode, the device enables multi-users to share Internet via ADSL/Cable Modem. The wireless port share the same IP to ISP through Ethernet WAN port. The Wireless port acts the same as a LAN port while at AP Router
  • TP-Link TL-WA7210N | User Guide - Page 53
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  WPS Status - Enable or disable the WPS function here.  Current PIN - The current value of the device's PIN displayed here. The default PIN of the device can be found in the label or User Guide.  Restore PIN - Restore the PIN of
  • TP-Link TL-WA7210N | User Guide - Page 54
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide be changed.  Type - Choosing dynamic IP to get IP address from DHCP server, or choosing static IP to configure IP address manually.  IP Address - Enter the IP address of your router in dotted-decimal notation (factory default: 192.
  • TP-Link TL-WA7210N | User Guide - Page 55
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4.7.1 Wireless Settings Selecting Wireless > Wireless Settings will enable you to configure the basic settings for your wireless network on the screen below (Figure 4-7). Figure 4-7 Wireless Settings in AP Client Router mode 
  • TP-Link TL-WA7210N | User Guide - Page 56
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.  Mode - This field determines the
  • TP-Link TL-WA7210N | User Guide - Page 57
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 802.11 WEP security. Each security option has its own settings as described below: WPA/WPA2 - Personal (Recommended)  and 63 characters.  Group Key Update Period - Specify the group key update interval in seconds. The value can be
  • TP-Link TL-WA7210N | User Guide - Page 58
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide • Automatic - Select WPA or WPA2 automatically based on the wireless station's capability and request. • WPA - Wi-Fi Protected Access. • WPA2 - WPA version 2.  Encryption - You can select either Automatic, or TKIP or AES.  Radius
  • TP-Link TL-WA7210N | User Guide - Page 59
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 4-9 Wireless MAC address Filtering The Wireless MAC Address Filtering feature allows you to control wireless stations accessing the AP, which depend on the station's MAC addresses.  Selected SSID - If Multi-SSID is enabled,
  • TP-Link TL-WA7210N | User Guide - Page 60
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide To Add a Wireless MAC Address filtering entry, clicking the Add New... button, and following these instructions entries, repeat steps access the router, while all other wireless stations cannot access the router, you should configure
  • TP-Link TL-WA7210N | User Guide - Page 61
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: 1) If you select the radio button Deny the stations specified by any enabled entries in the list to access for Filtering Rules, the wireless station B will still not be able to access the router, however, other wireless
  • TP-Link TL-WA7210N | User Guide - Page 62
    -WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Enable AP Isolation - Isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.  Note: If you are not familiar with the setting
  • TP-Link TL-WA7210N | User Guide - Page 63
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Mode - You can select manual or indoor for the mode. Click Save to keep your settings. 4.7.7 Throughput Monitor Selecting Wireless > Throughput Monitor will helps to watch wireless throughput information in the following screen
  • TP-Link TL-WA7210N | User Guide - Page 64
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide . To update this page manually assign new IP addresses. There are three submenus under the DHCP menu (shown as Figure 4-16): DHCP Settings, DHCP Clients List and Address Reservation. Clicking any of them will enable you to configure
  • TP-Link TL-WA7210N | User Guide - Page 65
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide DHCP server on your AP. The default setting is Disable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.  Start IP Address - This field specifies the
  • TP-Link TL-WA7210N | User Guide - Page 66
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide attached devices, click on the Refresh button. 4.8.3 Address Reservation Selecting DHCP > Address Reservation will enable you to specify a reserved IP address for a PC on the LAN, so the PC will always obtain the same IP address each
  • TP-Link TL-WA7210N | User Guide - Page 67
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: The changes won't take effect until the device reboots. 4.9 System Tools System Tools option helps you to optimize the configuration of your device. You can upgrade the AP to the latest version of firmware as well as backup
  • TP-Link TL-WA7210N | User Guide - Page 68
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 4-22 SNMP Agent - Choose default setting is private. Set Source - Set source defines the IP address or subnet for management systems that can control this 'set' community device.  Note: A restricted source can be a specific IP
  • TP-Link TL-WA7210N | User Guide - Page 69
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 4-23 Time settings  Time Zone - Select your local time zone from this pull-down list.  To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second
  • TP-Link TL-WA7210N | User Guide - Page 70
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4.9.3 Diagnostic Choose menu "System Tools of data bytes to be sent. The default is 64.  Ping Timeout - Time to wait for a response, in milliseconds. The default is 800.  Traceroute Max TTL - Set the maximum number of hops (max TTL
  • TP-Link TL-WA7210N | User Guide - Page 71
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure Watch Dog - Turn on/off Ping Watch Dog.  IP Address - The IP address of the target host where the Ping Watch Dog click the Submit button to make your settings in operation. 4.9.5 Speed Test Selecting System > Speed Test
  • TP-Link TL-WA7210N | User Guide - Page 72
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide each other. It should be used for the preliminary throughput estimation between two network devices. The estimation is rough. You can input the remote device's
  • TP-Link TL-WA7210N | User Guide - Page 73
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: The firmware version must Default Click the Restore button to reset all configuration settings to their default values.  Default User Name - admin.  Default Password - admin.  Default IP Address - 192.168.0.254.  Default
  • TP-Link TL-WA7210N | User Guide - Page 74
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4.9.9 Reboot Choose menu System Tools > Reboot, and then you can click the Reboot button to reboot the Device via the next screen. Figure 4-31 Reboot the Device Click the Reboot button to reboot the Device.  Some settings of the
  • TP-Link TL-WA7210N | User Guide - Page 75
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4.9.11 System log Choose menu System Tools > System Log, and then you can view the logs of the Device. Figure 4-33 System Log  Auto Mail Feature - Indicates whether auto mail feature is enabled or not.  Mail Settings - Set the
  • TP-Link TL-WA7210N | User Guide - Page 76
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the - Enabled or Disabled. The default value is disabled. To enable, click the Enable
  • TP-Link TL-WA7210N | User Guide - Page 77
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Packets Statistics Interval - The default reset the values of all entries to zero. Click the Delete All button to delete all entries in the table.  Statistics Table Figure 4-36 Statistics Table  IP Address/MAC Address - The IP
  • TP-Link TL-WA7210N | User Guide - Page 78
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Chapter 5. AP Client Router & AP Router Operation Mode This Chapter describes how to configure some advanced settings for your Access Point through the web-based management page. In the following explanations, we will take the device
  • TP-Link TL-WA7210N | User Guide - Page 79
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-1 Status 1. LAN This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask. 2. Wireless This field displays basic information or status for wireless function,
  • TP-Link TL-WA7210N | User Guide - Page 80
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4. Traffic Statistics This field displays the router's traffic statistics. 5. System Up Time The total up time of the router since it was powered on or reset. 5.3 Quick Setup Please refer to Section 3.2: "Quick Setup". 5.4 Operation
  • TP-Link TL-WA7210N | User Guide - Page 81
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Client - In this mode, the device can be connected to another device via Ethernet port and act as an adaptor to grant your wired devices access to a wireless network, especially for a Smart TV, Media Player, or game console only
  • TP-Link TL-WA7210N | User Guide - Page 82
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide I. Enter the client device's PIN on the Router Use this method if your client device has a Wi-Fi Protected Setup PIN number. Step 1: Keep the default Status as Enabled and click the Add Device button in then the following screen
  • TP-Link TL-WA7210N | User Guide - Page 83
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-6 WAN - Dynamic IP This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc.  IP Address - The IP address assigned by your ISP dynamically.  Subnet
  • TP-Link TL-WA7210N | User Guide - Page 84
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Click the Save button to save your settings. 2. If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting, select the Static IP option. The Static IP settings page will appear as shown in Figure 5-7.
  • TP-Link TL-WA7210N | User Guide - Page 85
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Secondary Connection - It's available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP
  • TP-Link TL-WA7210N | User Guide - Page 86
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-9 PPPoE Advanced Settings  MTU Size - The default MTU (Maximum Transmission Unit) size is 1480 bytes, which is usually fine. For some ISPs, you need modify the MTU. This should not be done
  • TP-Link TL-WA7210N | User Guide - Page 87
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-10 WAN - BigPond Cable  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.  Auth Server - Enter the authenticating server IP address or host name.  Auth Domain -
  • TP-Link TL-WA7210N | User Guide - Page 88
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 5. If
  • TP-Link TL-WA7210N | User Guide - Page 89
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Connect Manually - You can configure the Device to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Device will disconnect from your Internet connection, and you will not be able
  • TP-Link TL-WA7210N | User Guide - Page 90
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Connect on Demand - You can configure the Device to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to
  • TP-Link TL-WA7210N | User Guide - Page 91
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Click Save to save your settings.  Note: 1) Only the PC on your LAN can use the Clone MAC Address feature. 2) If you click Save, the Router will prompt you to reboot. 5.6.3 LAN Selecting Network > LAN will enable you to configure
  • TP-Link TL-WA7210N | User Guide - Page 92
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide be able to configure the corresponding function. The detailed explanations for each submenu are provided below. Figure 5-15 Wireless menu 5.7.1 Wireless Settings Choose menu Wireless > Wireless Settings, and then you can configure
  • TP-Link TL-WA7210N | User Guide - Page 93
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide with local laws. Incorrect settings may cause interference.  problems with another nearby access point. If you select auto, then the Device will select the best channel automatically.  Mode- This field determines the wireless mode
  • TP-Link TL-WA7210N | User Guide - Page 94
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2. Wireless settings in AP Client Router mode Figure 5-17 Wireless Settings in AP Client Router mode - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as
  • TP-Link TL-WA7210N | User Guide - Page 95
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: Note Dialog Ensure you select a correct country to comply with local laws. Incorrect settings may cause interference.  Transmission Power - The available options of transmission power are determined by the region
  • TP-Link TL-WA7210N | User Guide - Page 96
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-18 AP List Figure 5-19  Note: If you know the SSID of the desired AP, you can also input it to the field "Wireless Name of WISP Station" manually. Be sure to click the Save button to save your settings on this page.  Note:
  • TP-Link TL-WA7210N | User Guide - Page 97
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Near the center of the area in which your wireless Device. 5.7.2 Wireless Security Selecting Wireless > Wireless Security will enable you to configure the security of the wireless network for your device on the page as shown
  • TP-Link TL-WA7210N | User Guide - Page 98
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Each security option has its own settings as described below: WPA/WPA2 - Personal (Recommended)  WEP - Select 802.11 WEP security.  Version - You can select one of following versions: • Automatic - Select WPA-Personal
  • TP-Link TL-WA7210N | User Guide - Page 99
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide • For 128-bit encryption - You can enter 26 hexadecimal default setting, Disable. To set up an entry, click Enable, and follow these instructions: First, you must decide whether the specified wireless stations can or cannot access
  • TP-Link TL-WA7210N | User Guide - Page 100
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide button to save this entry. To add another entries, repeat steps 1~4. To modify or delete an existing entry: 3. able to access the router, while all other wireless stations cannot access the router, you should configure the Wireless
  • TP-Link TL-WA7210N | User Guide - Page 101
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: 1) If you select the radio button Deny the stations specified by any enabled entries in the list to access for Filtering Rules, the wireless station B will still not be able to access the router, however, other wireless
  • TP-Link TL-WA7210N | User Guide - Page 102
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 5.7.5 Antenna Alignment Selecting
  • TP-Link TL-WA7210N | User Guide - Page 103
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.7.7 Throughput Monitor Selecting Wireless > Throughput Monitor will helps to watch wireless throughput information in the following screen shown in Figure 5-26. Figure 5-26 Wireless Throughput 
  • TP-Link TL-WA7210N | User Guide - Page 104
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Received Packets - Packets received by the station  Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the
  • TP-Link TL-WA7210N | User Guide - Page 105
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100 is the default start IP address.  End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199 is the
  • TP-Link TL-WA7210N | User Guide - Page 106
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.8.3 Address Reservation Selecting DHCP > Address Reservation will enable you to specify a reserved IP address for a PC on the LAN, so the PC will always obtain the same IP address each time when it accesses the AP. Reserved IP
  • TP-Link TL-WA7210N | User Guide - Page 107
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.9 Forwarding There are four submenus under the Forwarding menu (shown in Figure 5-33): Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. The detailed
  • TP-Link TL-WA7210N | User Guide - Page 108
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Status - The status of this entry is either Enabled or Disabled.  Modify - To modify or delete an existing entry. To setup .  Note: If you set the virtual server of service port as 80, you must set the Web management port on
  • TP-Link TL-WA7210N | User Guide - Page 109
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.9.2 Port Triggering Selecting Forwarding > Port Triggering will enable you to set up Port Triggering entries on the page as shown in Figure 5-36. Figure 5-36 Port Triggering Once configured, operation is as follows: 1. A local host
  • TP-Link TL-WA7210N | User Guide - Page 110
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-37 Add or Modify a Triggering Entry the LAN will be refused. 3) Incoming Port Range enabled cannot overlap each other at the same time. 5.9.3 DMZ Selecting Forwarding > DMZ will allow you to set up an DMZ host on the page as
  • TP-Link TL-WA7210N | User Guide - Page 111
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: After you set the DMZ host, the firewall related to the host will not work. 5.9.4 UPnP Selecting Forwarding > UPnP will enable you to configure the UPnP function on the page as shown in Figure 5-39: Figure 5-39 UPnP Settings
  • TP-Link TL-WA7210N | User Guide - Page 112
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.10.1 Basic Security Choose menu Security > Basic Security, and then you can configure SPI Firewall is enabled by factory default. If you want all the IP (Internet Protocol) networks, through the use of cryptographic security services
  • TP-Link TL-WA7210N | User Guide - Page 113
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  TFTP ALG - To allow TFTP clients and servers to transfer data across NAT, click Enable.  H323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, click Enable. Click the Save button to save your settings default
  • TP-Link TL-WA7210N | User Guide - Page 114
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering.  UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set
  • TP-Link TL-WA7210N | User Guide - Page 115
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide After click the Add button, your PC's MAC Address will be placed in the Control List above. Click the Save button to save your settings.  Note: If your PC is blocked and you want to access the Device again, use a pin to press and
  • TP-Link TL-WA7210N | User Guide - Page 116
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-45 Parental Control Settings  Parental Control - Check Enable if you want this function to take effect; otherwise check Disable.  MAC Address of Parental PC - In this field, enter the
  • TP-Link TL-WA7210N | User Guide - Page 117
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4. Then you will go back to the Parental Control Settings page and , and you will be able to configure the corresponding function. The Device, providing convenient and strong Internet access control function, can control the Internet
  • TP-Link TL-WA7210N | User Guide - Page 118
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-48 Access Control Rule Management  Enable Internet Access Control - Select the check box to enable the Internet Access Control function, and then the Default Filter Policy can take effect.  Rule Name - Here displays the
  • TP-Link TL-WA7210N | User Guide - Page 119
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide settings. 7. Then you will go back to the Access Control Rule Management page and see the following list. Figure 5-49 Access Access Control > Host, and then you can view and set for the Access Control Rule. Figure 5-50 Host Settings 
  • TP-Link TL-WA7210N | User Guide - Page 120
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  For example: If you desire to restrict the Internet activities of host with MAC address 00-11-22-33-44-AA, you should follow the settings below: 1. Click Add New... button to enter the Add or Modify a Host Entry page. 2. In Mode
  • TP-Link TL-WA7210N | User Guide - Page 121
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings. 6. Go back to the Target Settings page and see the following list Figure 5-53 Access Target List Click the Add New... button to add a new target
  • TP-Link TL-WA7210N | User Guide - Page 122
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Click any of them, and you will be able to configure the corresponding function. 5.13.1 Static Routing List A an IP Address is the network portion, and which portion is the host portion.  Default Gateway - This is the IP Address of
  • TP-Link TL-WA7210N | User Guide - Page 123
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 3. Select Enabled or Disabled for this entry from or host.  Interface - This interface tells you whether the Destination IP Address is on the LAN & WLAN (internal wired and wireless networks), the WAN(Internet). You can click the
  • TP-Link TL-WA7210N | User Guide - Page 124
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 5.14 Bandwidth Control Figure 5-60 Bandwidth Control There are two submenus under the Bandwidth Control menu as shown in Figure 5-60: Control Settings and Rules List. Click any of them, and you will be able to configure the
  • TP-Link TL-WA7210N | User Guide - Page 125
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Description - The information of description include address range, the port range and protocol of transport layer.  Egress Bandwidth - The max upload speed which through the WAN port. The default number is 0.  Ingress Bandwidth
  • TP-Link TL-WA7210N | User Guide - Page 126
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-65 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries, follow the steps below. 1. Click the Add New... button as shown in Figure 5-64. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox
  • TP-Link TL-WA7210N | User Guide - Page 127
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-67 ARP List  MAC Address - The MAC address of the controlled computer in the LAN.  IP Address - The assigned IP address of the controlled computer in the LAN.  Status - Indicates whether or not the MAC and IP addresses
  • TP-Link TL-WA7210N | User Guide - Page 128
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-68 Comexe.cn DDNS Settings  To set up for DDNS, follow these instructions: 1) Enter the Domain Names your dynamic DNS service provider gave. 2) Enter the User Name for your DDNS account. 3) Enter the Password for your DDNS
  • TP-Link TL-WA7210N | User Guide - Page 129
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-69 Dyndns.org DDNS Settings  To set up for DDNS, follow these instructions: 1) Enter the User Name for . 3. If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 5-70. 119
  • TP-Link TL-WA7210N | User Guide - Page 130
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-70 No-ip.com DDNS Settings  To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS
  • TP-Link TL-WA7210N | User Guide - Page 131
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-71 The System Tools menu 5.17.1 Time Settings Choose menu "System Tools > Time Settings", and then you can configure the time on the following screen. Figure 5-72 Time settings  Time Zone - Select your local time zone from
  • TP-Link TL-WA7210N | User Guide - Page 132
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2. Click the Get GMT button to get GMT from the Internet.  To enable Daylight Saving: 1. Select the Enable Daylight Saving checkbox to enable daylight saving
  • TP-Link TL-WA7210N | User Guide - Page 133
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In
  • TP-Link TL-WA7210N | User Guide - Page 134
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 1. Download a most recent firmware upgrade file from our website (www.tp-link.com). 2. Enter or select the path name where you save the downloaded file on the computer into the File Name blank. 3. Click the Upgrade button. 4.
  • TP-Link TL-WA7210N | User Guide - Page 135
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  To restore the AP's configuration, follow these instructions: 1. Click the Browse button to find the configuration file which you want to restore. 2. Click the Restore button to update the configuration with the file whose path is
  • TP-Link TL-WA7210N | User Guide - Page 136
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-79 Password It is strongly recommended that you change the factory default user name and password of the AP. All users who try to access is enabled or not.  Mail Settings - Set the receiving and sending mailbox address, server
  • TP-Link TL-WA7210N | User Guide - Page 137
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure 5-81 Mail Account Settings  From - Your mail box address. - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log
  • TP-Link TL-WA7210N | User Guide - Page 138
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide of DoS protection in Security settings will be disabled.  Packets Statistics Interval - The default value is 10. Select a button to refresh the page. Click the Reset All button to reset the values of all entries to zero. Click
  • TP-Link TL-WA7210N | User Guide - Page 139
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Total  Packets - The total number of packets received and transmitted "current transmitting rate / Max transmitting rate".  Modify  Reset - Reset the values of the entry to zero.  Delete - Delete the existing entry in the table
  • TP-Link TL-WA7210N | User Guide - Page 140
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Appendix A: FAQ 1. How do I configure the router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the
  • TP-Link TL-WA7210N | User Guide - Page 141
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link to configure Virtual Server or DMZ Host. 3) How to configure the "Service Port", and your IP address behind the IP Address,
  • TP-Link TL-WA7210N | User Guide - Page 142
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide  Note: Your opposite side should call your WAN IP configuration takes effect, to configure to the router by typing http://192.168.0.254:88/ (the router's LAN IP "Service Port", and your IP address behind the IP Address, assuming 192.168
  • TP-Link TL-WA7210N | User Guide - Page 143
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure A-8 Virtual Servers A-9 Add or Modify a Virtual server Entry 5. The wireless stations encrypted. 4) If the wireless connection is ready, but you can't access the router, check the IP Address of your wireless stations. 133
  • TP-Link TL-WA7210N | User Guide - Page 144
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Appendix B: Configuring the PC In this section, we'll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed. 1. Configure
  • TP-Link TL-WA7210N | User Guide - Page 145
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below:  Setting IP address automatically Select
  • TP-Link TL-WA7210N | User Guide - Page 146
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Figure B-3 Note: For Windows 98 OS or before, the PC and router may need to be restarted.  Setting IP address manually 1. Select Use the following IP address radio button. And the following items available 2. If the router's LAN IP
  • TP-Link TL-WA7210N | User Guide - Page 147
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Now: Click OK to keep your settings. Figure B-4 137
  • TP-Link TL-WA7210N | User Guide - Page 148
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Appendix C: Specifications General Standards and Protocols IEEE 802.3, 802.3u, 802.11b, 802.11g and 802.11n, TCP/IP, DHCP Safety & Emission Ports FCC, CE One 10/100M Auto-Negotiation LAN RJ45 port, supporting passive PoE
  • TP-Link TL-WA7210N | User Guide - Page 149
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Appendix D: Glossary  802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial
  • TP-Link TL-WA7210N | User Guide - Page 150
    TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide Alliance (WICA), comprising more than 300 companies, whose products are certified by the Wi-Fi Alliance, based on the IEEE 802.11 standards (also called Wireless LAN (WLAN) and Wi-Fi). This certification warrants interoperability
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access
Point
REV2.0.0
1910010786