TP-Link TL-WR740N User Guide - Page 31

Network, 4.5.1 LAN - ip

Get TP-Link TL-WR740N - 150Mbps Wireless Lite N Router IEEE 802.11n 802.11g 802.11b Built-in PDF manuals and user guides
UPC - 813120016543
View all TP-Link TL-WR740N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

TL-WR740N/TL-WR741ND 150Mbps Wireless N Router ) Note: The default PIN code of the Router can be found in its label or the QSS configuration screen as Figure 4-3. c). You will see the following screen when the new device successfully connected to the network. ) Note: 1. The QSS LED on the Router will light green for five minutes if the device has been successfully added to the network. 2. The QSS function cannot be configured if the Wireless Function of the Router is disabled. Please make sure the Wireless Function is enabled before configuring the QSS. 4.5 Network Figure 4-5 the Network menu There are three submenus under the Network menu (shown in Figure 4-5): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. 4.5.1 LAN Choose menu "Network → LAN", you can configure the IP parameters of the LAN on the screen as below. - 24 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
- 24
-
)
Note:
The default PIN code of the Router can be found in its label or the QSS configuration screen as
Figure 4-3.
c).
You will see the following screen when the new device successfully connected to the
network.
)
Note:
1. The QSS LED on the Router will light green for five minutes if the device has been
successfully added to the network.
2. The QSS function cannot be configured if the Wireless Function of the Router is disabled.
Please make sure the Wireless Function is enabled before configuring the QSS.
4.5 Network
Figure 4-5
the Network menu
There are three submenus under the Network menu (shown in Figure 4-5):
LAN
,
WAN
and
MAC
Clone.
Click any of them, and you will be able to configure the corresponding function.
4.5.1 LAN
Choose menu “
Network
→
LAN
”, you can configure the IP parameters of the LAN on the screen
as below.