TP-Link TL-WR740N User Guide - Page 45

Enable Wireless Router Radio, Enable SSID Broadcast - wireless bridge

Get TP-Link TL-WR740N - 150Mbps Wireless Lite N Router IEEE 802.11n 802.11g 802.11b Built-in PDF manuals and user guides
UPC - 813120016543
View all TP-Link TL-WR740N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

TL-WR740N/TL-WR741ND 150Mbps Wireless N Router ¾ Channel - This field determines which operating frequency will be used. The default channel is set to 6. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. ¾ Mode - Select the desired mode. The default setting is 11bgn mixed. 11b only - Select if all of your wireless clients are 802.11b. 11g only - Select if all of your wireless clients are 802.11g. 11n only- Select only if all of your wireless clients are 802.11n. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the Router. It is strongly recommended that you set the Mode to 802.11b&g&n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Router. ¾ Channel width - Select the channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. ) Note: If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ¾ Max Tx Rate - You can limit the maximum tx rate of the Router through this field. ¾ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. ¾ Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. If you select the Enable SSID Broadcast checkbox, the Wireless Router will broadcast its name (SSID) on the air. ¾ Enable WDS - Check this box to enable WDS. With this function, the Router can bridge two or more WLANs. If this checkbox is selected, you will have to set the following parameters as shown below. Make sure the following settings are correct. - 38 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
- 38
-
¾
Channel -
This field determines which operating frequency will be used. The default channel
is set to 6. It is not necessary to change the wireless channel unless you notice interference
problems with another nearby access point.
¾
Mode -
Select the desired mode. The default setting is 11bgn mixed.
11b only -
Select if all of your wireless clients are 802.11b.
11g only -
Select if all of your wireless clients are 802.11g.
11n only-
Select only if all of your wireless clients are 802.11n.
11bg mixed -
Select if you are using both 802.11b and 802.11g wireless clients.
11bgn mixed -
Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless
stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless
stations can connect to the Router. It is strongly recommended that you set the Mode to
802.11b&g&n
, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to
the Router.
¾
Channel width -
Select the channel width from the pull-down list
.
The default setting is
automatic, which can adjust the channel width for your clients automatically.
)
Note:
If
11b only
,
11g only
, or
11bg mixed
is selected in the
Mode
field, the
Channel Width
selecting field will turn grey and the value will become 20M, which is unable to be changed.
¾
Max Tx Rate -
You can limit the maximum tx rate of the Router through this field.
¾
Enable Wireless Router Radio -
The wireless radio of this Router can be enabled or
disabled to allow wireless stations access.
¾
Enable SSID Broadcast -
When wireless clients survey the local area for wireless networks
to associate with, they will detect the SSID broadcast by the Router. If you select the
Enable
SSID Broadcast
checkbox, the Wireless Router will broadcast its name (SSID) on the air.
¾
Enable WDS -
Check this box to enable WDS. With this function, the Router can bridge two
or more WLANs. If this checkbox is selected, you will have to set the following parameters as
shown below. Make sure the following settings are correct.