TP-Link Touch P5 Touch P5 V1 User Guide
TP-Link Touch P5 Manual
 |
View all TP-Link Touch P5 manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link Touch P5 manual content summary:
- TP-Link Touch P5 | Touch P5 V1 User Guide - Page 1
Touch P5 User Guide AC1900 Touch Screen Wi-Fi Gigabit Router REV1.0.0 1910011363 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 2
5. Position Your Touch P5 5 Chapter 2. Configure Touch P5 as a Router 6 2. 1 Connect Your Touch P5 7 2. 2 Log into Your Touch P5 8 2. 4 Mode Selection 11 2. 5 Wireless Settings 12 2. 6 WPS...15 2. 7 Guest Network 17 2. 8 Parental Controls 19 2. 9 Devices Control 22 2. 10 Printer - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 3
& Reset 81 3. 10 Administrator Password 82 3. 11 About 83 3. 12 FAQ ...84 Chapter 4. Configure Touch P5 as an Access Point 85 4. 1 Connect Your Touch P5 86 4. 2 Log into Your Touch P5 87 4. 3 Quick Setup 89 4. 4 Mode Selection 90 4. 5 Wireless Settings 91 4. 6 WPS...93 4. 7 Devices Control - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 4
-Fi access for guests sharing your home or office network in a controlled manner without needing to expose private Wi-Fi access codes or other personal data. IPv6 Supported Touch P5 supports IPv6, which is the foundation of the next generation of the Internet and enables a range of new services and - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 5
efficient Wi-Fi connection • Supports wireless router, access point and repeater modes • Guest Network access provides secure Wi-Fi access for guests sharing your home or office network • Parental Controls allows parents or administrators to establish restricted access policies for children or staff - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 6
(Access Point Mode) Total Clients Tap here to view clients' information and block unauthorized clients. Guest Network Tap here to enable guest network and change the settings. Guest Network SSID & Password (2.4GHz & 5GHz) The password is periodically (daily by default) generated by your Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 7
of your Touch P5, such as Quick Setup, Mode Selection, Parental Controls, etc. 1. 3. 2. The Back Panel Your Touch P5's back panel shows the connection ports, buttons and antennas. Refer to the following for detailed instructions. Item Description Power For connecting your Touch P5 to power - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 8
for Operation To connect and use your Touch P5 for Internet sharing, you must have the following: • Broadband Internet Access Service (DSL/Cable/Ethernet). • One DSL/Cable Modem that has an RJ45 connector (which is not necessary if your Touch P5 is connected directly to the Ethernet). • Computers - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 9
your Touch P5 in router mode which will provide Internet access for multiple wired and wireless devices simultaneously. 2 Touch P5 supports two IPv6 Connection, IPTV, NAT Forwarding and Firmware Upgrade, etc., are configured through web-based utility. Chapter 2 . Configure Touch P5 as a Router 6 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 10
you want to use your Touch P5 for media sharing, storage sharing and printer sharing, please connect the USB storage device or printer to the USB port of your Touch P5. Remote Access via FTP Server Local Storage Sharing Media Sharing Printer Sharing Chapter 2 . Configure Touch P5 as a Router 7 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 11
log in with the default username and password (admin/admin). 3. The first time you log in, you will need to set up a new username and password for your Touch P5. Enter your new username and password and the new password again to confirm. Click Confirm. Chapter 2 . Configure Touch P5 as a Router 8 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 12
Note: Apps on the touchscreen will also need to use the new password that you have set to log in. Chapter 2 . Configure Touch P5 as a Router 9 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 13
-screen instructions to complete the configuration. Note: If you change the preset wireless network name (SSID) and wireless password during the quick setup process, all your wireless devices must use the new SSID and password to connect to your Touch P5. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 14
Touch P5 to a router, repeater or an access point. Router Mode (Default): Touch P5 can provides Internet access for multiple wired and wireless devices simultaneously. Repeater Mode: Touch P5 can extend your existing wireless coverage by repeating the wireless signal. Access Point Mode: Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 15
radio, wireless network name, password and security option, etc., default SSID is TP-LINK_XXXX and the value is case-sensitive. Note: 1. If you use a wireless device to change the wireless settings, you will be disconnected when the settings are effective. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 16
clients. Note: When 802.11n only mode is selected, only 802.11n wireless stations can connect to your Touch P5. It is strongly recommended that you select problems with another nearby access point. Transmit Power: Select either High, Middle, or Low to specify the data transmit power. The default - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 17
Interval. Group Key Update Period: Enter the number of seconds (minimum 30) to control the time interval for the encryption key automatic renewal. The default is 0, indicating still able to access the Internet, select the Enable AP Isolation checkbox. Chapter 2 . Configure Touch P5 as a Router 14 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 18
Setup) supported devices and your Touch P5. Wireless devices that support WPS, including Android phones, tablets, and most USB network cards, can connect to your Touch P5 through this method. (WPS is not supported Protected Setup button. 1 ) Tap the Start WPS button on the screen of your Touch P5, - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 19
established within 2 minutes. Option 2: Use the PIN Use this option if your client device asks for your Touch P5's PIN. 1 ) Tap Connect to this router via PIN on the above screen of your Touch P5 to get the PIN, you can use the default one or generate a new one. 2 ) On the client device, enter your - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 20
update interval to weekly, monthly. Or you can also select Never to set a static password for your guest network. If you select Never, please create a password between 8 and 63 ASCII characters or between 8 and 64 hexadecimal characters (0-9, a-f, A-F). Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 21
checkbox to allow the clients in your guest network to access each other. Allow guests to access my local network: Select this checkbox to allow the clients in your guest network access your local network shares and printers, not just Internet access. Chapter 2 . Configure Touch P5 as a Router 18 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 22
PM) on weekdays and not at other times. 1. On the menu screen, tap the Parental Controls icon to open it. Toggle the button to enable Parental Controls. 2. Tap Devices Under Parental Controls and then tap Add to add a device under parental controls. Chapter 2 . Configure Touch P5 as a Router 19 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 23
4 ) Select the time period and the date, and tap Done. Note: The access time schedule takes effect based on your Touch P5's system time. The system time can be set through the Clock app. 5 ) Tap Save to add the device to parental controls list. Note: If you want to modify a device, tap the device to - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 24
or delete a rule, tap Edit to set up according to your needs. 4. Return to the Content Restriction page and tap Save. Done! Now you can control your children's Internet access according to your needs. Chapter 2 . Configure Touch P5 as a Router 21 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 25
my Touch P5. How can I 1. On the menu screen, tap the Devices Control icon to open it. Toggle the button to enable Devices do that? Control. 2. Tap Online Devices to view the connected clients. 3. Select the device(s) to be blocked and tap Block. Chapter 2 . Configure Touch P5 as a Router 22 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 26
in Blacklist automatically. Done! Note: If you want to add a device manually or delete a blocked device, tap Edit on the Devices In Blacklist page to set up according to your needs. Now devices in the blacklist cannot connect to your Touch P5. Chapter 2 . Configure Touch P5 as a Router 23 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 27
is supported by your Touch P5. Printers unlisted may be incompatible with your Touch P5. 3. Install the TP-LINK USB Printer Controller Utility TP-LINK USB Printer Controller Utility helps you access the shared printer. Download and Install the utility on each computer that needs printer service - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 28
service. 1 ) Double-click the icon on your desktop to launch the USB Printer Controller. 2 ) Highlight the printer you share. Windows Mac 3 ) Click the Auto-Connect for Printing tab to pull down a list, then select Set Auto-Connect Printer. Windows Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 29
Mac 4 ) Select the printer you share, then click Apply. Windows Mac Chapter 2 . Configure Touch P5 as a Router 26 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 30
to share the scan feature of MFPs (Multi-Function Printers). To scan with TP-LINK USB Printer Controller, right-click the printer and select Network Scanner. Then, a scanning window will pop up. Follow on-screen instructions to finish the scanning process. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 31
www.dyndns.com. 3. Enter the Username, Password, Domain Name (such as lisadns.ddns.net), and select Update Interval of the account. 4. Tap Login & Save. Note: If you want to use a new DDNS account, please Logout first, then login with the new account. Chapter 2 . Configure Touch P5 as a Router 28 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 32
2. 12 LAN The LAN app helps to change the default LAN settings of your Touch P5. Touch P5 is preset with a default LAN IP 192.168.0.1, which you can use to log in to its web- together with the IP address identifies your local IP subnet. 4. Tap Save. Chapter 2 . Configure Touch P5 as a Router 29 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 33
manually reserve an IP address for a client that is connected to your Touch P5. Touch P5 will assign addresses within this specified range to its clients. It is from 192.168.0.100 to 192.168.0.199 by default. 4 ) Enter a value for the Address Lease Time. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 34
be automatically assigned a new dynamic IP address. 5 ) The Default Gateway is automatically filled the same as the LAN IP address of your Touch P5. Enter Primary DNS and Secondary DNS if the ISP offers. device. 4 ) Enter the Description for the device. Chapter 2 . Configure Touch P5 as a Router 31 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 35
reserved address to modify it. If you want to add or delete a reserved address, tap Edit to set up according to your needs. Chapter 2 . Configure Touch P5 as a Router 32 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 36
sharing the Internet. When some device is streaming video on Internet or downloading with P2P software, it will affect the Internet experience of other applications. The QoS (Quality of Service priority, and middle priority is greater than low priority. Chapter 2 . Configure Touch P5 as a Router 33 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 37
enter the Device Name and MAC Address manually. Tap Save to add the rule to Port: Enter the destination port for your application, usually each application has a fixed port, please ensure you enter the correct the port. Tap Save to add the rule to the list. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 38
5. The QoS rule will list in the priority table. Note: If you want to add or delete a QoS rule, tap Edit to set up according to your needs. Chapter 2 . Configure Touch P5 as a Router 35 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 39
Touch P5 is running. The system time you configure here will be used for other time-based functions like Parental Controls . 1. On the menu screen, tap the Clock icon to open it. 2. Tap to configure the time settings. To set the time of your Touch P5 your Touch P5 can access the - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 40
. Manually: Select to set the date and time manually, then tap Save. To set up daylight saving time of your Touch P5: 1 ) Select Daylight Saving Time. 2 ) Select the checkbox to enable Daylight Saving Time. Set the start and end time and then tap Save. Chapter 2 . Configure Touch P5 as a Router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 41
tap Save. 3 ) To use your Touch P5 as a clock, you need to stay at the home page of Clock app. Then the clock will display on the screen while your Touch P5 is locked. Note: Overusing the screen as a clock will decrease the life span of the screen. Chapter 2 . Configure Touch P5 as a Router 38 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 42
the screen. 3. By default, the screen saver will start if the screen is idle for 3 minutes, you can change the wait time. Note: If you select Never, the screen will stay on and never go to sleep and this will decrease the life span of the screen. Chapter 2 . Configure Touch P5 as a Router 39 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 43
: Your Touch P5 will shut down and boot again. Reset: To reset your Touch P5 to its factory default settings and all the settings you have configured will be erased. Note: Please do NOT power off your Touch P5 during the rebooting or resetting process. Chapter 2 . Configure Touch P5 as a Router 40 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 44
of your Touch P5 through the touchscreen. But logging in through web-based management page still requires the password. 2. If you change the administrator password on the screen, logging into web-based management page also requires the new password. Chapter 2 . Configure Touch P5 as a Router 41 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 45
2. 19 About The About app displays the product model, hardware and firmware information of your Touch P5. On the menu screen, tap the About icon to open it. Chapter 2 . Configure Touch P5 as a Router 42 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 46
.net/, then log in with the username and password you set for your Touch P5. 2 ) Select Basic > USB Settings > Sharing Access. Focus on the Folder Sharing section. Click the button to disable Share All, then click Add to add a new sharing folder. Chapter 2 . Configure Touch P5 as a Router 43 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 47
will be required to enter the username and password you set when accessing the USB disk. 1 ) Visit http://tplinkwifi.net/, then log in with the username and password you set for your Touch P5. 2 ) Select Advanced > USB Settings > Sharing Access. Chapter 2 . Configure Touch P5 as a Router 44 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 48
your USB disk. 1 ) Visit http://tplinkwifi.net/, then log in with the username and password you set for your Touch P5. 2 ) Go to Advanced > USB Settings > Sharing Access. 3 ) Make sure Network Neighborhood is ticked, and enter a Network/Media Server Name as you like, such as MyShare, then click - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 49
the Internet. 1. Access the USB disk 1 ) Connect Your USB Disk Insert your USB storage device into your Touch P5's USB port directly or using the username and password you set for your Touch P5. b . Select Advanced > USB Settings > Sharing Access. c . Choose to use the default Account (admin) or - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 50
net/, then log in with the username and password you set for your Touch P5. 2 ) Select Basic > USB Settings > Sharing Access. 3 ) Focus on the section of Folder Sharing. Click the button to disable Share All, then click Add to add a new sharing folder. Chapter 2 . Configure Touch P5 as a Router 47 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 51
Media Player. b . Click the media server name (Touch_P5-share by default) under the list of Other Libraries, then you can directly view photos, play music and watch movies that you share on the USB disks. Pad Use a third-party DLNA-supported player. Chapter 2 . Configure Touch P5 as a Router 48 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 52
By default, Share All is enabled so all content on the USB disk is shared. If you want to only share specific folders, follow the steps below: 1 ) Visit http://tplinkwifi.net/, then log in with the username and password you set for your Touch P5. 2 ) Select Basic > USB Settings > Sharing Access - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 53
): Click Save and skip to Step 5. 4. Configure LAN ports. Windows users are recommended to choose from the first two types. Fill in Address Prefix provided by ISP, and click Save. Note: Find Help on the management interface to know more about items. Chapter 2 . Configure Touch P5 as a Router 50 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 54
5. Click Status on the left to check whether you succeed or not. The following figure is an example of a successful PPPoE configuration. Chapter 2 . Configure Touch P5 as a Router 51 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 55
IPTV connection. I want to: Configure IPTV setup to enable Internet /IPTV /Phone service provided by my Internet Service Provider (ISP). How can I do that? 1. Visit http://tplinkwifi.net/, and log in with the username and password you set for your Touch P5. 2. Go to Advanced > Network > IPTV to - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 56
Done! Your IPTV setup is done now! You may need other configurations on your set-top box before enjoying your TV. Chapter 2 . Configure Touch P5 as a Router 53 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 57
log in with the username and password you set for your Touch P5. 3. Go to Advanced > NAT Forwarding > Virtual Servers, and click Add. 4. Click View Existing Services, and select your Service Type (in this case: HTTP). The External Port, Internal Port and Protocol will be automatically filled with - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 58
Time 4 players, etc. Follow the steps below to configure the port triggering rules: 1. Visit http://tplinkwifi.net, and log in with the username and password you set for your Touch P5. 2. Go to Advanced > NAT Forwarding > Port Triggering and click Add. 3. Click View Existing Applications, and select - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 59
To solve this problem, set your computer as a DMZ with all ports opened. 1. Assign a static IP address to your computer, for example 192.168.0.100. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for your Touch P5. 3. Go to Advanced > NAT Forwarding > DMZ and select - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 60
to it to open the corresponding ports. With UPnP enabled, the applications or Router INTERNET If necessary, you can follow the steps to change the status of UPnP. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for your Touch P5. 2. Go to Advanced >NAT Forwarding - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 61
can download the latest firmware file from our website and upgrade the firmware to the latest version. 1. Download the latest firmware file from our website: TP-LINK Support. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for your Touch P5. Go to Advanced > System - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 62
shares the same password, please try the administrator password of the touchscreen. 3. Restore your Touch P5 to its factory default settings: With your Touch P5 powered on, press and hold the Reset button on the back panel until the Touch P5 logo displays. Q6. I cannot log into my Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 63
4 ) Click LAN settings, deselect the following three options and click OK; 5 ) Go to Advanced > Restore advanced settings, and click OK. Chapter 2 . Configure Touch P5 as a Router 60 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 64
. 6. Reset your Touch P5 to factory default settings: With your Touch P5 powered on, press and hold the Reset button on the back panel until the Touch P5 logo displays. Note: You'll need to reconfigure your Touch P5 to surf the Internet once your Touch P5 is reset. If this doesn't solve the problem - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 65
Start button and make sure the Service status is Started. And then click OK. g . Connect to wireless network. 2. If you can find other wireless network except your own, please follow the steps below: 1 ) Make sure your computer/device is still in the range of your Touch P5/modem, move closer if it - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 66
halfduplex instead of full-duplex mode. In other words, the repeater has to process one-way communication between your host network and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased. Touch P5 supports two configuration methods: Web-based - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 67
4. Select Repeater mode and tap Save. Note: Your Touch P5 will reboot to make your changes take effect, and please do NOT operate during the process. 5. Go to the menu screen and tap the Quick Setup icon to open it. 6. Set your Region and tap Next. Chapter 3 . Configure Touch P5 as a Repeater 64 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 68
screen instructions to complete the configuration. 8. Once the configuration is completed, please follow the instructions below to relocate your Touch P5 Touch P5 and host network. It's better to locate it in a spacious place, such as near the corridors. Chapter 3 . Configure Touch P5 as a Repeater - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 69
clients to the network of your Touch P5. Note: Your Touch P5 shares your host network's Wi-Fi password for both 2.4GHz and 5GHz networks default username and password (admin/admin). 5. Click the Mode button on the upper-right corner of title bar, select Repeater and click Save. Note: Your Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 70
7. Follow the Quick Setup instructions to complete the configuration. 8. Once the configuration is completed, please follow the instructions below to relocate your Touch P5 at an ideal location your wireless clients to the network of your Touch P5. Chapter 3 . Configure Touch P5 as a Repeater 67 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 71
shares your host network's Wi-Fi password for both 2.4GHz and 5GHz networks, but may have different wireless network name if you customize the names during the configuration. Please connect your wireless devices to the extended network of your Touch P5. Chapter 3 . Configure Touch P5 as a Repeater - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 72
: 1. Open a web-browser on your computer, visit http://tplinkwifi.net and log in with the default username and password (admin/admin). 2. Go to Settings > Network, and focus on the Ethernet Port section. 3. Select 2.4GHz or 5GHz band and click Save. Chapter 3 . Configure Touch P5 as a Repeater 69 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 73
Touch P5 to a router, repeater or an access point. Router Mode (Default): Touch P5 can provides Internet access for multiple wired and wireless devices simultaneously. Repeater Mode: Touch P5 can extend your existing wireless coverage by repeating the wireless signal. Access Point Mode: Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 74
products marketed in the U.S. are fixed to the U.S. region. 2. Configure the wireless settings according to your needs. To set the host network connection of your Touch P5: 1 ) Select Host Network. Chapter 3 . Configure Touch P5 as a Repeater 71 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 75
please try to move your Touch P5 closer to your host router, then tap Rescan. Or, select Other...to enter the SSID manually. 5 ) Once a network is selected, the SSID and security settings of that network will automatically be filled in. Tap Host Password to enter the password of the host network in - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 76
SSID: Select this checkbox if you want to hide your Touch P5's SSID from the Wi-Fi network list, and your wireless device will need to manually join the network. Extended Password: The password of the extended network is the same as the host network. Chapter 3 . Configure Touch P5 as a Repeater 73 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 77
Touch P5. How can I 1. On the menu screen, tap the Devices Control icon to open it. Toggle the button to enable Devices do that? Control. 2. Tap Online Devices to view the connected clients. 3. Select the device(s) to be blocked and tap Block. Chapter 3 . Configure Touch P5 as a Repeater 74 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 78
in Blacklist automatically. Done! Note: If you want to add a device manually or delete a blocked device, tap Edit on the Devices In Blacklist page to set up according to your needs. Now devices in the blacklist cannot connect to your Touch P5. Chapter 3 . Configure Touch P5 as a Repeater 75 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 79
3. 6 LAN By default, your Touch P5 is set to obtain an IP address automatically from the host router. The LAN app allows Default Gateway to enter the gateway in dotted decimal notation . It should be in the same subnet as the IP address. 6. Tap Save. Chapter 3 . Configure Touch P5 as a Repeater - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 80
DHCP Server is set to be Auto by default and the function will automatically turn on or off to assign valid IP addresses to client devices according to the DHCP server settings of the host network. If you select On, please configure it manually. Chapter 3 . Configure Touch P5 as a Repeater 77 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 81
. After the dynamic IP address expires, the client will be automatically assigned a new dynamic IP address. • Default Gateway (Optional): Enter the LAN IP address of your Touch P5. • Primary/Secondary DNS (Optional): Enter this parameters as provided by your ISP. If you select Off, please make sure - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 82
reserved address to modify it. If you want to add or delete a reserved address, tap Edit to set up according to your needs. Chapter 3 . Configure Touch P5 as a Repeater 79 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 83
the screen. 3. By default, the screen saver will start if the screen is idle for 3 minutes, you can change the wait time. Note: If you select Never, the screen will stay on and never go to sleep and this will decrease the life span of the screen. Chapter 3 . Configure Touch P5 as a Repeater 80 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 84
Your Touch P5 will shut down and boot again. Reset: To reset your Touch P5 to its factory default settings and all the settings you have configured will be erased. Note: Please do NOT power off your Touch P5 during the rebooting or resetting process. Chapter 3 . Configure Touch P5 as a Repeater 81 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 85
of your Touch P5 through the touchscreen. But logging in through web-based management page still requires the password. 2. If you change the administrator password on the screen, logging into web-based management page also requires the new password. Chapter 3 . Configure Touch P5 as a Repeater 82 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 86
3. 11 About The About app displays the product model, hardware and firmware information of your Touch P5. On the menu screen, tap the About icon to open it. Chapter 3 . Configure Touch P5 as a Repeater 83 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 87
Touch P5 to its factory default settings, and create a new administrator password. Q4. What can I do if I cannot access the Internet? 1. Check if the Internet is working properly by connecting to your host network. If not, contact your Internet Service Provider. 2. Move closer to the host router - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 88
Touch P5 in access point mode which will transform your existing wired network to a wireless network. We recommend that you use access point mode when your wireless devices need to access to a wired network, or when you require a supplement of ports for your wired router. 4 Your Touch P5 supports - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 89
the default SSID (Wireless Network Name) and Wireless Password printed on the product label at the bottom of your Touch P5 to connect wirelessly. Note: You can also connect your computer to the Ethernet port on your Touch P5 via an Ethernet cable. Chapter 4 . Configure Touch P5 as an Access Point - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 90
on your computer, visit http://tplinkwifi.net and log in with the default username and password (admin/admin). 3. Click the Mode button on the upper-right corner of title bar, select Access Point and click Save. Note: Your Touch P5 will reboot to make your changes take effect, and please do NOT - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 91
Chapter 4 . Configure Touch P5 as an Access Point 88 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 92
to the wireless network of your Touch P5. Note: If you change the preset wireless network name (SSID) and wireless password during the quick setup process, all your wireless devices must use the new SSID and password to connect to your Touch P5. Chapter 4 . Configure Touch P5 as an Access Point 89 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 93
Touch P5 to a router, repeater or an access point. Router Mode (Default): Touch P5 can provides Internet access for multiple wired and wireless devices simultaneously. Repeater Mode: Touch P5 can extend your existing wireless coverage by repeating the wireless signal. Access Point Mode: Touch P5 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 94
, wireless network name, password and security option, etc default SSID is TP-LINK_XXXX and the value is case-sensitive. Note: 1. If you use a wireless device to change the wireless settings, you will be disconnected when the settings are effective. Chapter 4 . Configure Touch P5 as an Access Point - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 95
to change the wireless channel unless you notice interference problems with another nearby access point. Transmit Power: Select either High, Middle, or Low to specify the data transmit power. The default and recommended setting is High. Chapter 4 . Configure Touch P5 as an Access Point 92 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 96
option if your client device has a Wi-Fi Protected Setup button. 1 ) Tap the Start WPS button on the screen of your Touch P5, and the WPS button will show as below during the process. 2 ) Immediately press the WPS button of the client device. Chapter 4 . Configure Touch P5 as an Access Point 93 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 97
device asks for your Touch P5's PIN. 1 ) Tap Connect to this AP via PIN on the above screen of your Touch P5 to get the PIN, you can use the default one or generate a new one. 2 ) On the client device, enter your Touch P5's PIN to connect. Chapter 4 . Configure Touch P5 as an Access Point 94 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 98
Touch P5. How can I 1. On the menu screen, tap the Devices Control icon to open it. Toggle the button to enable Devices do that? Control. 2. Tap Online Devices to view the connected clients. 3. Select the device(s) to be blocked and tap Block. Chapter 4 . Configure Touch P5 as an Access Point - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 99
in Blacklist automatically. Done! Note: If you want to add a device manually or delete a blocked device, tap Edit on the Devices In Blacklist page to set up according to your needs. Now devices in the blacklist cannot connect to your Touch P5. Chapter 4 . Configure Touch P5 as an Access Point 96 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 100
mask in dotted decimal notation. It determines the network portion and host portion of the IP address. 5. Tap Default Gateway to enter the gateway in dotted decimal notation . It should be in the same subnet as the IP address. 6. Tap Save. Chapter 4 . Configure Touch P5 as an Access Point 97 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 101
DHCP Server is set to be Auto by default and the function will automatically turn on or off to assign valid IP addresses to client devices according to the DHCP server settings of the host network. If you select On, please configure it manually. Chapter 4 . Configure Touch P5 as an Access Point 98 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 102
client will be automatically assigned a new dynamic IP address. • Default Gateway (Optional): Enter the LAN IP address of your Touch P5. • Primary/Secondary DNS (Optional): Enter this parameters as an address reservation entry for your device. Chapter 4 . Configure Touch P5 as an Access Point 99 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 103
reserved address to modify it. If you want to add or delete a reserved address, tap Edit to set up according to your needs. Chapter 4 . Configure Touch P5 as an Access Point 100 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 104
screen. 3. By default, the screen saver will start if the screen is idle for 3 minutes, you can change the wait time. Note: If you select Never, the screen will stay on and never go to sleep and this will decrease the life span of the screen. Chapter 4 . Configure Touch P5 as an Access Point 101 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 105
Touch P5 will shut down and boot again. Reset: To reset your Touch P5 to its factory default settings and all the settings you have configured will be erased. Note: Please do NOT power off your Touch P5 during the rebooting or resetting process. Chapter 4 . Configure Touch P5 as an Access Point - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 106
Touch P5 through the touchscreen. But logging in through web-based management page still requires the password. 2. If you change the administrator password on the screen, logging into web-based management page also requires the new password. Chapter 4 . Configure Touch P5 as an Access Point 103 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 107
4. 13 About The About app displays the product model, hardware and firmware information of your Touch P5. On the menu screen, tap the About icon to open it. Chapter 4 . Configure Touch P5 as an Access Point 104 - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 108
wired router via an Ethernet cable. If not, contact your Internet Service Provider. 2. Tap Quick Setup on the menu screen to run the setup again. 3. Tap Reboot & Reset on the menu screen, select Reboot to reboot your Touch P5 and try again. Q2. What can I do if I forgot my wireless network password - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 109
IP, PPPoE, DHCP, ICMP, NAT, SNTP 1 10/100/1000M Auto-Negotiation Internet RJ45 port; 4 10/100/1000M Auto-Negotiation Ethernet RJ45 ports supporting Auto MDI/MDIX; 1 USB 2.0 port and 1 USB 3.0 port supporting storage/FTP/Media/Print Server; Cabling Type 10Base-T: UTP category 3, 4, 5 cable (maximum - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 110
existing traditional phone lines. • ISP (Internet Service Provider) - A company that provides access to the Internet. • MTU (Maximum Transmission Access Point and to the wireless network name. • WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 111
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 112
, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there required Luxembourg Norway None Implemented General authorization required for network and service supply (not for spectrum) This subsection does not apply for - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 113
Planned License required General authorization required if used outside own premises None No info General authorization required for network and service supply (not for spectrum) Note: Please don't use the product outdoors in France. Canadian Compliance Statement This device complies with - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 114
power source. • Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. • Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE - TP-Link Touch P5 | Touch P5 V1 User Guide - Page 115
equipment: Product Description: AC1900 Touch Screen Wi-Fi Gigabit Router Model No.: Touch P5 Trademark: TP-LINK We declare under our , Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1 EN 55022: 2010 + AC: 2011 EN 55024:
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
 |
 |
REV1.0.0
1910011363
Touch P5
User Guide
AC1900 Touch Screen Wi-Fi Gigabit
Router