TRENDnet TEW-412APBO User's Guide

TRENDnet TEW-412APBO Manual

Get TRENDnet TEW-412APBO PDF manuals and user guides View all TRENDnet TEW-412APBO manuals
Add to My Manuals
Save this manual to your list of manuals

TRENDnet TEW-412APBO manual content summary:

  • TRENDnet TEW-412APBO | User's Guide - Page 1
    User's Guide 1
  • TRENDnet TEW-412APBO | User's Guide - Page 2
    Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. JUL. 2004 User's Guide 2
  • TRENDnet TEW-412APBO | User's Guide - Page 3
    Settings 7 4.1. Primary Setup 8 4.2. System 12 4.3. Operating Mode 13 4.4. Status 15 4.5 Traffic Log 16 4.6 Access Control 17 4.7 Advanced Wireless 18 4.8. SNMP INFO 20 4.9. Upgrade Firmware 21 5. Troubleshooting ...23 User's Guide 3
  • TRENDnet TEW-412APBO | User's Guide - Page 4
    Thank you for purchasing TRENDnet's Wireless 802.11g Outdoor AP Bridge. This user guide will assist you with the installation procedure. The package you have received should contain the following items: For TEW-412APBO TEW-412APBO User's Guide CD-ROM Quick Installation Guide POE Host & Power Cord
  • TRENDnet TEW-412APBO | User's Guide - Page 5
    proper operation, please keep the unit away from water and other damaging elements. Please read the user manual thoroughly before you install the device. The device should only be repaired by authorized and qualified personnel. may be damaged by direct sunlight or heat sources. User's Guide 5
  • TRENDnet TEW-412APBO | User's Guide - Page 6
    3. AP Default Settings The default settings are shown following. User admin Password admin AP IP Address 192.168.1.250 AP Subnet Mask 255.255.255.0 RF ESSID ap11g 11g RF Channel 6 Mode 11b+g Encryption Disabled User's Guide 6
  • TRENDnet TEW-412APBO | User's Guide - Page 7
    Wireless 11g AP, you must use your web browser and manually input http://192.168.1.250 into the Address box and press Enter. The Main Page will appear. Wireless 11g AP. The Security Settings section described later in this manual describes how to change the password. Once you have input the
  • TRENDnet TEW-412APBO | User's Guide - Page 8
    AP and get it working properly using the settings on this screen. LAN IP Address and Subnet Mask: This is the AP's IP Address and Subnet Mask as seen on the internal LAN. The default value is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask. Wireless: This section provide the Wireless
  • TRENDnet TEW-412APBO | User's Guide - Page 9
    Wireless Settings SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must not exceed 32 characters, which may be any using the same encryption level and key. WEP keys must consist of the letters "A" through "F" and the numbers "0" through "9." User's Guide 9
  • TRENDnet TEW-412APBO | User's Guide - Page 10
    WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft's OS family, only Windows XP has incorporated this by default. . Please input the period of renewal time. The default selection is 300 seconds. User's Guide 10
  • TRENDnet TEW-412APBO | User's Guide - Page 11
    choose your algorithms method. You can select between TKIP or AES. Please input your RADIUS Server IP address. Please input the Authentication port of your RADIUS server. The default port being used is 1812 default selection is 300 seconds. * Click Apply to save your settings. User's Guide 11
  • TRENDnet TEW-412APBO | User's Guide - Page 12
    your local PC. Click Restore to restore Access Point's configuration from your local PC * Check all the settings and click Apply to save them. User's Guide 12
  • TRENDnet TEW-412APBO | User's Guide - Page 13
    4.3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. User's Guide 13
  • TRENDnet TEW-412APBO | User's Guide - Page 14
    link communication. The remote AP MAC address to be filled at this selection should be the LAN MAC address that is displaying at the Operating your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature. Wireless Bridge: This mode allows the connection
  • TRENDnet TEW-412APBO | User's Guide - Page 15
    re-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and the current configuration type. Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and
  • TRENDnet TEW-412APBO | User's Guide - Page 16
    of activity logs as a file on your PC's hard drive, Log viewer software must be used. In the Send Log to field, enter the fixed IP address of the PC running the Log viewer software. The AP will send updated logs to that PC. To see a temporary log of the AP's most
  • TRENDnet TEW-412APBO | User's Guide - Page 17
    This function will allow administrator to have access control by enter MAC address of client stations. When Enable this function, two new options will up to 40 different MAC addresses. Please follow the format that it required when an address is input. * Click Apply to save your settings. User
  • TRENDnet TEW-412APBO | User's Guide - Page 18
    client. Shared Key: Shared Key is only available if the WEP option is implemented. Shared Key authentication supports authentication of clients as either a member of those who know a shared secret key or a member the AP to synchronize the wireless network. The default value is 100. User's Guide 18
  • TRENDnet TEW-412APBO | User's Guide - Page 19
    a DTIM Interval value. Access Point Clients hear the beacons and awaken to receive the broadcast and multicast messages. * Click Apply to save your settings. User's Guide 19
  • TRENDnet TEW-412APBO | User's Guide - Page 20
    settings. SNMP is a popular network monitoring and management protocol. SNMPv2c To enable the SNMP support feature, select Enable. Otherwise, select Disable. Identification Contact In the contact field, enter either Read-Only or Read-Write. Click Apply to save your settings. User's Guide 20
  • TRENDnet TEW-412APBO | User's Guide - Page 21
    the firmware upgrade file. 3. Click the Firmware Upgrade button. 4. On the Firmware Upgrade screen, click the Browse button to find the firmware upgrade file. User's Guide 21
  • TRENDnet TEW-412APBO | User's Guide - Page 22
    5. Double-click the firmware upgrade file. 6. Click the Upgrade button, and follow the on-screen instructions. Note: Do not power off the AP or press the Reset button while the firmware is being upgraded. User's Guide 22
  • TRENDnet TEW-412APBO | User's Guide - Page 23
    Troubleshooting Problems I can't access my AP. Cause: The unit is not powered on. There is not a network connection. The computer you are using does not have a compatible IP Address IP address of your computer to 192.168.1.15 or another unique IP Address IP Addresses unique IP Address. And the IP must
  • TRENDnet TEW-412APBO | User's Guide - Page 24
    Wireless Troubleshooting I can't access the Wireless AP from a wireless network card Cause: Out of range. IP Address is not set correctly. Resolution: Make sure that devices that may cause interference. Check your IP Address to make sure that it is compatible with the Wireless AP. User's Guide 24
  • TRENDnet TEW-412APBO | User's Guide - Page 25
    severe than those specified in the manual. Warranty service may be obtained by contacting TRENDware support for all customers for the duration of the warranty period on this product. TRENDware Technical Support Tel: +1-310-626-6252 Fax: +1-310-626-6267 E-mail: [email protected] www.TRENDnet
  • TRENDnet TEW-412APBO | User's Guide - Page 26
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
User’s Guide
1