Toshiba 52HM84 Owner's Manual - English - Page 24

Adding channels to the TV's memory

Get Toshiba 52HM84 - 52inch Rear Projection TV PDF manuals and user guides
UPC - 022265262122
View all Toshiba 52HM84 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Introduction Connecting your TV Using the Remote Control Adding channels to the TV's memory When you press Channel y or z, your TV will stop only on the channels stored in the TV's channel memory. Follow the steps below and on the next page to program all active channels into the TV's memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 25). To program channels automatically: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z until the TV/CABLE is highlighted, and then press ENTER to display the pull-down menu. 3. Press y or z to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE. LANGUAGE CLOCK SET ANT 1 / 2 TV / CABLE CH PROGRAM ADD / ERASE SET UP : SELECT ENTER : SET TV CABLE 4. Press ENTER. 5. Press z to select CH PROGRAM. Note: To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. TOP AR E ENT TV/VIDEO RECALL POWER INFO 123 456 78 +10 100 0 MFAEVNOURITE FAV 9 CHRTN ENT PIC GUID SIZE MENU DVDMENU ENTER ER FAV EXIT CLE TV CBL/SAT CH VCR DVD VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE STOP PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP REC POP CH LIGHT MENU yzx • ENTER Channel yz LANGUAGE CLOCK SET ANT 1 / 2 TV / CABLE CH PROGRAM ADD / ERASE SET UP ENGLISH 00:00 ANT1 CABLE ADD : MOVE ENTER : START 6. Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory. While the TV is cycling through the channels, the message "Programming Now-Please Wait" appears. 7. When channel programming is complete, the message "Completed" appears. 8. Press Channel y or z to view the programmed channels. Setting up your TV Using the TV's Features Appendix Index 24 #01E22-25_46,52,62HM84 24 Black (E) 46HM84, 52HM84, 62HM84 5/31/04, 12:20 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Introduction
Connecting
y
our TV
Using the
Remote Control
Setting up
y
our TV
Using the TV’s
F
eatures
Appendix
Index
24
(
E
) 46HM84, 52HM84, 62HM84
Adding channels to the TV’s memory
When you press Channel
y
or
z
, your TV will stop only on the
channels stored in the TV’s channel memory.
Follow the steps below and on the next page to program all active
channels into the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in its memory. After the channels are stored automatically,
you can manually add or erase individual channels (see page 25).
To program channels automatically:
1.
Press MENU, and then press
x
or
•
until the SET UP menu
appears.
2. Press
y
or
z
until the TV/CABLE is highlighted, and then press
ENTER to display the pull-down menu.
3. Press
y
or
z
to highlight either TV or CABLE, depending on
which you use. If you use an antenna, highlight TV; if you use
cable, highlight CABLE.
LANGUAGE
SET
UP
CLOCK
SET
TV
CABLE
ANT
1 / 2
TV / CABLE
CH
PROGRAM
ADD / ERASE
SELECT
:
:
SET
ENTER
4.
Press ENTER.
5. Press
z
to select CH PROGRAM.
LANGUAGE
SET
UP
CLOCK
SET
00:00
ENGLISH
ANT
1 / 2
ANT1
TV / CABLE
CABLE
ADD
CH
PROGRAM
ADD / ERASE
MOVE
:
:
START
ENTER
6.
Press ENTER to start channel programming. The TV will
automatically cycle through all the TV or Cable channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
“Programming Now—Please Wait” appears.
7.
When channel programming is complete, the message
“Completed” appears.
8.
Press Channel
y
or
z
to view the programmed channels.
1
2
3
4
5
6
7
8
9
ENT
100
0
POWER
RECALL
CHRTN
FAV
FAV
TV
/
VIDEO
+10
PIC SIZE
EXIT
INFO
STOP
POP DIRECT CH
MUTE
SLEEP
TV/VCR
PAUSE
FF
REW
SKIP
/
SEARCH
SPLIT
SWAP
POP CH
LIGHT
REC
CH SCAN
FREEZE
SOURCE
PLAY
TV
CBL/SAT
VCR
DVD
VOL
CH
FAVORITE
ENTER
DVDMENU
MENU
T
O
P
M
E
N
U
G
U
I
D
E
C
L
E
A
R
E
N
T
E
R
MENU
yzx
•
Channel
yz
Note:
To tune the TV to a channel not programmed
in the channel memory, you must use the
Channel Number buttons on the remote
control.
ENTER
#01E22-25_46,52,62HM84
5/31/04, 12:20 PM
24
Black