Toshiba SD-V296 Owner's Manual - English - Page 16

Satellite Link You can set the unit to start recording whenever it detects a video signal from the external tuner. Preparing for the Satellite Link Timer Recording: Preparation on the tuner • Satellite link accepts only the connection from L1 (rear) with the external tuner. (The connection from L2 cannot read any signals from the external tuner.) • The external tuner should be equipped with some kind of timer function. Using timer function of the tuner, set it to output audio/video signals when it comes to the time you want to start recording, and stop output audio/video signals when it comes to the time you want to finish recording. Refer to the tuner's manual on how to set the timer. • Make sure to turn off the tuner when you finish setting. VCR Preparation on this unit L1 DIGITAL AUDIO OUT DVD AUDIO OUT S-VIDEO OUT COMPONENT VIDEO OUT Y DVD/VCR VCR AUDIO OUT AUDIO IN L L L COAXIAL R CB/ PB R R VIDEO OUT VIDEO IN CR/ PR external tuner RCA audio/video cables Note: • Please purchase the necessary cables at your local store. (Refer to page 7.) 1 Press [SPEED] to select the desired tape speed. SPEED Tape speed Recording / playback time Type of tape T60 T120 T160 SP mode 1hour 2hours 2-2/3hours SP SLP mode 3hours 6hours 8hours 2 In stop mode, press [SETUP]. SETUP 5 Set the desired start minutes. If you wish to go back to the left, press [s]. or 6 Press [B] to set satellite link standby mode. SATELLITE LINK 0 1 : 0 0 PM SATELLITE LINK 0 1 : 3 0 PM [ON] 3 Select "SATELLITE LINK". Then press [B] to go to next step. or - M E N U - TIMER PROGRAMMING B SATELLITE LINK AUTO REPEAT [OFF] CLOCK SET LANGUAGE SELECT 4 Set the desired start hour. Then press [B] to go to next step. or SATELLITE LINK 1 2 : 0 0 AM • The hour can be selected from 1-12 with AM or PM. • When the external tuner signal is stopped, recording will be stopped. • TIMER REC indicator on this unit lights up and the unit goes to the DVD mode. If you do not use DVD function, turn off the unit. • Satellite unit must be turned on for VCR satellite link to start. If an external tuner is not set to output signals, satellite link will remain in standby mode. To cancel the satellite link function in standby mode: Press [T-SET] on the remote control or [ C/A (STOP/EJECT)] on this unit. To cancel the satellite link function while the satellite link recording is in progress: Press [ C/A (STOP/EJECT)] on this unit. Note: • You cannot stop the satellite link recording with [STOP C] on the remote control. Note: • If you have not set the clock, "CLOCK SET" menu will appear at step 2. Refer to "Clock Setting" on page 12. • You cannot set the ending time for the satellite link timer recording on this unit. • Recording picture will be distorted if the copy protection signal is being detected during satellite link timer recording. • When a regular timer recording and the satellite link timer recording are overlapped, those recordings are recorded as illustrated below. e.g.) In case of the satellite link timer recording is overlapped on the existing timer recording. e.g.) In case of the timer recording is programmed in the middle e.g.) In case of the timer recording is overlapped on the existing of the satellite link timer recording satellite link timer recording. timer recording timer recording timer recording satellite link satellite link satellite link recording result recording result recording result Copying a Cassette Tape Warning: Unauthorized recordings of copyrighted cassette tapes may be an infringement of copyright laws. 1) Insert a pre-recorded cassette tape into another external device for playback. 2) Insert a recordable cassette tape into this unit for recording. 3) Press [SPEED] on the remote control to select recording speed (SP or SLP). 4) Press [INPUT SELECT] on the remote control to select L1 or L2. Choose L1 if device is connected to rear input jacks, or L2 if connected to the front. Refer to "Front Panel" and "Rear Panel" on page 7 for more details. 5) Press [I REC] on the unit. 6) Press "PLAY" button on the external device. 7) To stop recording, press [ C/A (STOP/EJECT)] on this unit, then stop playback of the external device. output jacks of external device AUDIO OUT L or R VIDEO OUT L1 RCA audio/video cables DVD/VCR VCR AUDIO OUT AUDIO IN L L R R VIDEO OUT VIDEO IN rear of the unit You can use a video disc player, cable/satellite box or other audio/video component with audio/video output jacks. Note: • For best results during dubbing, use buttons on this unit whenever possible. The remote control might affect another device's operation. • Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. • L2 input jacks are on the front of this unit. • Please purchase the necessary cables at your local store. (Refer to page 7.) - 16 - EN E8EB5UD_SD-V296KU_EN_ES_v1.indd 16 2008/07/14 10:37:28