Troy-Bilt TB146 Operation Manual
Troy-Bilt TB146 Manual
 |
View all Troy-Bilt TB146 manuals
Add to My Manuals
Save this manual to your list of manuals |
Troy-Bilt TB146 manual content summary:
- Troy-Bilt TB146 | Operation Manual - Page 1
Handle Choke Lever Starter Rope Tine Shield Fuel Cap Primer Bulb Air Filter Cover Tines DIDN'T START? Repeat the starting instructions. If the unit still fails to start, refer to the operator's manual for additional starting and troubleshooting information. In cold weather (below 40°F), refer - Troy-Bilt TB146 | Operation Manual - Page 2
OF CONTENTS Service 2 Safety 2 Know Your Unit 3 Assembly 3 Oil and Fuel 3 Starting and Stopping 4 Operation 4 Maintenance 5 Cleaning and Storage 6 Optional Accessory 6 Troubleshooting 6 Specifications 6 Warranty 16 All information, illustrations, and specifications in this manual are - Troy-Bilt TB146 | Operation Manual - Page 3
Filter Cover OIL AND FUEL USING THE RIGHT OIL Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SJ. DO NOT use dirty oil. Failure to use clean oil of the correct type can cause premature engine wear and failure. Handlebar Oil Fill Plug Primer Bulb ADDING OIL - Troy-Bilt TB146 | Operation Manual - Page 4
hold down the cultivator. Pull the starter rope in a controlled motion until the unit starts. Primer Bulb Fig. 7 manual for more information about purchasing these accessories.) STARTING INSTRUCTIONS 1. Check the oil level. Refer to Checking the Oil Level. 2. Fill the fuel tank. Refer to Fueling - Troy-Bilt TB146 | Operation Manual - Page 5
be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures, take your unit to any non-road engine repair establishment, individual or authorized service dealer. NOTE: Maintenance, replacement, or repair of the - Troy-Bilt TB146 | Operation Manual - Page 6
cover before tightening the screws. Tighten the screws. Fig. 23 TROUBLESHOOTING PROBLEM THE ENGINE WILL NOT START, IDLE OR ACCELERATE SOLUTION The fuel tank is empty The primer bulb was not pressed enough The fuel is old (over 30 days) The spark plug is fouled The air filter is dirty The idle - Troy-Bilt TB146 | Operation Manual - Page 7
TB146 EC Cultivadora con motor de 4 tiempos con arranque eléctrico Manual del Operador English - Page 1 Cómo Repita las instrucciones de arranque. Si el motor todavía no arranca, consulte el manual del operador para obtener información adicional sobre cómo solucionar problemas en el arranque. SI - Troy-Bilt TB146 | Operation Manual - Page 8
ío. De no hacerlo, lleve la unidad a Troy-Bilt o a otro distribuidor de servicio calificado para un • No toque el motor ni el silenciador. Estas partes se ponen extremadamente calientes durante la operación y aún en la sección Lista de piezas de este manual. El uso de cualquier pieza o accesorio no - Troy-Bilt TB146 | Operation Manual - Page 9
SEGURIDAD SÍMBOLO SIGNIFICADO • ADVERTENCIA DE SUPERFICIE CALIENTE No toque un silenciador ni un cilindro caliente. Puede quemarse. Estas partes se calientan mucho con el uso. Luego de apagarse permanecen calientes durante un corto tiempo. • CULTIVADORES PARA JARDINES - LAS PUAS GIRATORIAS PUEDEN - Troy-Bilt TB146 | Operation Manual - Page 10
eléctrico o el accesorio de arranque eléctrico opcional en la parte trasera de la unidad. Consulte la sección de Operación del manual del operador del Arrancador Eléctrico o Accesorio de Arranque Eléctrico Opcional Power Start Bit™. 5. No apriete el acelerador, oprima y mantenga oprimido el botón ON - Troy-Bilt TB146 | Operation Manual - Page 11
. Línea de llenado NOTA: Use la botella vacía que guardó del uso inicial para medir la cantidad correcta de aceite. Llene la botella hasta la parte Fig. 15 superior de la etiqueta, aproximadamente hasta 3.04 onzas fluidas (90 ml) de aceite (Fig. 15). 6. Limpie todo el aceite que pueda haberse - Troy-Bilt TB146 | Operation Manual - Page 12
sin previo aviso. ACCESORIO OPCIONAL CARACTERÍSTICAS DEL ARRANCADOR ELÉCTRICO Y DEL ACCESORIO POWER BIT START™ Esta unidad está diseñada para usarse con un arrancador eléctrico o un accesorio Power Bit Start™ opcionales, los que se venden por separado. Si opta por arrancar la unidad utilizando uno - Troy-Bilt TB146 | Operation Manual - Page 13
NOTES 13 - Troy-Bilt TB146 | Operation Manual - Page 14
NOTES 14 - Troy-Bilt TB146 | Operation Manual - Page 15
NOTES 15 - Troy-Bilt TB146 | Operation Manual - Page 16
Troy-Bilt warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part Belts, Saw Chains, Guide Bars, Cultivator Tines. C. Troy-Bilt does not extend any
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
Set the unit on a flat, level
surface. Unscrew the oil fill
plug. Pour the entire bottle of
oil into the oil fill hole. Reinstall
the oil fill plug.
NOTE: DO NOT
overfill. Never
add oil directly into the fuel
tank.
DO NOT
mix oil with
gasoline.
6
Unpacking the Unit
Assembling the Unit
1
Remove all contents from the
carton.
Align the hole in the wheel
bracket with the desired hole
in the wheel assembly. Insert
the clevis pin through the
aligned holes. Insert the cotter
pin into the clevis pin.
Insert the wheel assembly into
the wheel bracket. The "J"
shape of the wheel assembly
should point away from the
unit.
3
Loosen the two handlebar
knobs. Swing the handlebars
up into the operating position.
NOTE:
Do not pinch the
throttle cable or switch wires.
4
Handlebar Knobs
2
Tighten the two handlebar
knobs to secure the
handlebars. Readjust the
throttle cable and switch wires.
NOTE:
Do not over tighten the
handlebar knobs.
5
Starting the Unit
11
Stand in starting position.
WARNING:
Tines
WILL
ROTATE
on
START
. Always stand
in starting position with foot on
wheel when starting the unit.
10
DO NOT
squeeze the throttle
control.
Pull
starter rope in controlled
motion until unit starts.
Wait
60 seconds.
DO NOT
Squeeze the throttle
control.
7
Place the unit on a level surface.
Remove the fuel cap. Fill the fuel
tank. Replace the fuel cap. Move
the unit at least 30 ft. (9.1 m)
from the fuel container and the
fueling site before starting the
engine.
NOTE:
Use fresh unleaded
gasoline (less than 30 days old).
8
Press
primer bulb
10 times
,
or until fuel is visible
1
9
Primer Bulb
10 X
IF THE ENGINE IS HOT
Go back to Step 9
Need Help?
Call 1-800-828-5500
NO ASSEMBLY TOOLS REQUIRED
Starter Rope
Fuel Cap
Lower Handle
Handle Knobs
Throttle Control
On/ Off Switch
Upper Handle
Tine Shield
Choke Lever
Tines
Air Filter
Cover
Primer Bulb
Electric Starter or
Power Start Bit Optional!
THESE OPTIONAL ACCESSORIES
ARE SOLD SEPARATELY!
This unit has an alternate starting method
that many find easier to use than pulling a
rope. Please contact a local retailer or call
1-800-828-5500
for more information.
Information may also be found at
www.troybilt.com
Then squeeze the throttle
control for an additional 30 to
60 seconds to let the engine
warm up further. The unit may
be used during this period.
12
Starting the Unit
DIDN’T START?
Repeat the starting instructions.
If the unit still fails to start,
refer to the operator’s manual
for additional starting and
troubleshooting information.
In cold weather (below 40°F),
refer to the operator's manual for
additional starting instructions.
Assembling the Unit
Wheel Bracket
Wheel
Assembly
Clevis Pin
Cotter Pin
Español — Page 7
English — Page 1
769-07453A P00
02/12
NEED HELP?
CALL 1-800-828-5500 IN U.S. OR 1-800–668–1238 IN CANADA
TB146 EC
4-Cycle
Electric Start Capable
Cultivator
Operator’s Manual