Uniden ANA9610 English Owners Manual
Uniden ANA9610 Manual
 |
View all Uniden ANA9610 manuals
Add to My Manuals
Save this manual to your list of manuals |
Uniden ANA9610 manual content summary:
- Uniden ANA9610 | English Owners Manual - Page 1
® ANA 9610 900 MHz Analog PBX Cordless Telephone Operating Guide - Uniden ANA9610 | English Owners Manual - Page 2
than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the Operating Guide for this - Uniden ANA9610 | English Owners Manual - Page 3
Covered under one or more of the following U.S. patents: 4,511,761 4,523,058 4,595,795, 4,597,104 4,797,916 4,803,491 5,157,686 5,253,268 and other patents pending. ® OMANA9610 ©1997 Uniden America Corporation. Printed in the USA. All rights reserved. - Uniden ANA9610 | English Owners Manual - Page 4
contains a Rechargeable Sealed Lead-Acid Battery. n Do not short circuit the battery. n Do not charge the Rechargeable Sealed Lead-Acid Battery used in this equipment in any charger other than the one designed to charge this battery as specified in this Guide . Using another charger may damage - Uniden ANA9610 | English Owners Manual - Page 5
Handset Controls & Functions 1 9 2 talk bat low lock msg talk chan vol 15 14 16 3 10 4 11 hold xfer conf flash redial pause search memo 5 12 6 1 2abc 3def 13 4ghi 5 jkl 6mno 7 7 8 9 pqrs tuv wxyz # 0oper 8 1. Ringer ON/OFF switch 2. Message Display 3. Transfer (xfer) Key - Uniden ANA9610 | English Owners Manual - Page 6
Base Unit Controls & Functions hold Key status Indicator page/find Key Tone Pulse Tone/Pulse slide Switch - Uniden ANA9610 | English Owners Manual - Page 7
OF CONTENTS Important Safety Instructions 2 About Your ANA 9610 4 Important Electrical Considerations 5 Range 5 Telephone Line Problems 5 Radio Interference 6 More Than One Cordless Telephone 6 Privacy 6 ANA 9610 Features 7 Installing Your ANA 9610 8 Selecting the Installation Location - Uniden ANA9610 | English Owners Manual - Page 8
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked - Uniden ANA9610 | English Owners Manual - Page 9
. 13. Do not use the telephone to report a gas leak in the vicinity of the leak. CAUTION: To reduce the risk of fire or injury to persons by the battery, read and follow these instructions: 1. Use only the appropriate type and size Battery Pack specified in this Operating Guide. 2. Do not dispose of - Uniden ANA9610 | English Owners Manual - Page 10
purchase of the Uniden ANA 9610 Cordless Telephone. The ANA 9610 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. It is designed to work with a PBX system. To get the most from your ANA 9610, please read this Operating Guide thoroughly. To - Uniden ANA9610 | English Owners Manual - Page 11
to such actions to allow you time for making necessary arrangements to continue uninterrupted service. If you are having trouble with your telephone service, you must first disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it - Uniden ANA9610 | English Owners Manual - Page 12
please check around your office to see what appliances may be causing the problem. In addition, we recommend that the Base not be plugged into a . Privacy Note: Cordless phones are radio devices. Communications between the Handset and Base Unit of your cordless telephone are accomplished by - Uniden ANA9610 | English Owners Manual - Page 13
ANA 9610 Features n Super Long Range 900MHz Digital n 2-line, 16-digit LCD Display n Headset Jack n Stand with Spare Battery Charging Capability n Second Spare Battery n AutoStandby n AutoTalk n Vibrator Ringer Alert n Easy Installation n Out of Range Protection n Low Battery Protection System n - Uniden ANA9610 | English Owners Manual - Page 14
Mount Adapter. If you will use the ANA 9610 with a Standard 2500 type Telephone Desk Unit, place the ANA 9610 near that phone. Keep the Base Unit and Handset (making color-coded connections). Note: Your Uniden Telephone Dealer or a telephone supply store can advise you on the proper adapter or - Uniden ANA9610 | English Owners Manual - Page 15
or terminals unless the telephone line has been disconnected at the network interface. n Use caution when installing or modifying telephone lines. Line in From Telephone Jack You can also connect a standard 2500-type desk phone to the ANA 9610: To Optional 2500-type Telephone Connect to the LINE - Uniden ANA9610 | English Owners Manual - Page 16
you are not sure whether your system is Tone or Pulse dialing. Applying Power to the Base and Charger Units AC Adapter Line in From Telephone Jack Line out to Standard 2500 type Desk Phone Use only the supplied AC Adapter: AD-9500 - Uniden ANA9610 | English Owners Manual - Page 17
The AC Adapter furnished with this phone may be equipped with a polarized ANA 9610 allows you to place the Handset in the Charging Unit with or without the Belt Clip attached. The Charging Unit also has the ability to charge a second battery with or without the Handset being charged. The Battery - Uniden ANA9610 | English Owners Manual - Page 18
channel of the Wall Mount stand. 4. Plug one end of the short telephone cord into the LINE jack on the Base Unit. Optionally, plug one end of a standard 2500 type desk phone into the PHONE jack. Then place the telephone cord(s) inside the molded channel(s) on the bottom of the Wall Mount stand - Uniden ANA9610 | English Owners Manual - Page 19
a wall. Before mounting your phone, consider the following: n Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. n Make sure the wall material is capable of supporting the weight of the Base - Uniden ANA9610 | English Owners Manual - Page 20
cord into the LINE jack on the Base Unit. Optionally, plug one end of a standard 2500 type desk phone into the PHONE jack. Then place the telephone cord(s) inside the molded channel(s) on the bottom of the Wall Mount stand. 4. Place the Base Unit on the posts of the wall screws and - Uniden ANA9610 | English Owners Manual - Page 21
telephone cord into a telephone wall jack. 6. Plug the AC Adapter into a standard 120V AC wall outlet by following step 7 of the Standard Wall Plate Mounting. Charging Unit Wall Mounting The Charging Unit is also designed to be wall mounted. you can mount your phone capable of supporting the weight - Uniden ANA9610 | English Owners Manual - Page 22
3. Place the Charging Unit on the posts of the wall screws and push down until it's firmly seated. Strain Relief 3/16" 1 1/2" 4. Plug the AC Adapter into a standard 120V AC wall outlet. AC Adapter - Uniden ANA9610 | English Owners Manual - Page 23
Attaching the Belt Clip to the Handset You can use the Belt Clip to attach the Handset to your belt or pocket for convenient portability. 1. Snap the tab out of the Belt Clip notch on the top of the Handset. 2. Slide the clip into the tab slot. (CAUTION: The Belt Clip is designed to fit snugly onto - Uniden ANA9610 | English Owners Manual - Page 24
and slide the clip up at the same time. Once the Belt Clip is removed remember to re-install the cover tab. Installing the Handset Battery Pack 1. Remove the battery cover by pressing the latch and sliding the cover down and off of the Handset. 2. Slide the - Uniden ANA9610 | English Owners Manual - Page 25
the cover up until it latches into the Handset. Charging the Handset Battery Pack The Rechargeable Sealed Lead-Acid Battery Pack must be fully charged before using your ANA 9610 for the first time. (Note: Charge the Battery Pack without interruption for 5 hours.) 1. Place the Handset in the front - Uniden ANA9610 | English Owners Manual - Page 26
Packs The Charger Unit of your ANA 9610 is equipped to charge the Spare Battery Pack with or without the Handset in the front slot. 1. Slide the Spare Battery Pack into the second slot in the Charging Unit until the retaining clip snaps over the top of the pack. 2. Make sure the CHARGE 2 indicator - Uniden ANA9610 | English Owners Manual - Page 27
Cleaning the Battery and Charging Unit Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset, Spare Battery Pack and Charging Unit about once a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. - Uniden ANA9610 | English Owners Manual - Page 28
Using Your ANA 9610 Handset Before using your ANA 9610, be sure to raise the antenna to the vertical position. Note: Operation of the ANA 9610 is performed using the Handset out of the Charging Unit. - Uniden ANA9610 | English Owners Manual - Page 29
ANA 9610 Handset Controls talk chan vol Condition Handset Earpiece Volume (During a Call) Ringer Select (Standby Mode) Action LCD Display Press vol on the front of the - Uniden ANA9610 | English Owners Manual - Page 30
is at the range limit of the ANA 9610, or no power is going to the Base Unit, you may see: Take the following action: CHANNEL BUSY LINE IN USE NO SERVICE Condition Action During a Call In Standby Mode Warning Tone Can't make or answer calls (Phone may ring intermittently) Move back in range - Uniden ANA9610 | English Owners Manual - Page 31
immediately. Press talk When you finish the call, place the Handset back in the Charging Unit. AutoStandby automatically hangs up the phone. -OR- Press talk to hang up the phone Making a Call Press talk. The talk Icon will illuminate after the Handset/Base are connected, and you'll see: talk - Uniden ANA9610 | English Owners Manual - Page 32
Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. Contact your PBX Administrator for more information. Placing a call "on hold" Press hold. You'll hear a "beep" and see: HOLD talk To resume the call, press hold or talk. Transferring a - Uniden ANA9610 | English Owners Manual - Page 33
- to program the xfer key for "Hook Flash" and 9 for outside transfers only: Press memo. PHONE NO.? Press flash. Press 9. Press memo. F F9 LOCATION? Press xfer. STORING Note: For the ANA 9610, conference and transfer keys are operated by the Flash Hook function. Please, program you system - Uniden ANA9610 | English Owners Manual - Page 34
while on a call. Press once to program a "Hook Flash" in a Feature Button. REDIAL To dial the last number called, press talk, then redial. The phone will redial the last number called. PAUSE Press once to program a Pause while storing a number in Memory. SEARCH Press to begin Memory Search. (See the - Uniden ANA9610 | English Owners Manual - Page 35
Memory Use these buttons to operate the ANA 9610 Memory hold xfer conf flash redial pause search memo Storing a Number 1. Press memo. You will hear a beep, and see the message: PHONE NO.? 2. Enter the number (up to 16 digits) you want to store. a. To program a Pause in the dialing sequence - Uniden ANA9610 | English Owners Manual - Page 36
beeps. This is confirmation that you have programmed 5551234 into memory location 12 and you see: LOCATION? 12 The phone then returns to Standby. Erasing a Stored Number 1. Press memo. PHONE NO.? 2. Press memo. 3. Enter the memory location number (01) to (20) you want to clear. You will hear - Uniden ANA9610 | English Owners Manual - Page 37
already established a connection between Handset and Base Unit. 1. Press talk. 2. Press memo. 02 talk 3. Enter the Memory Location (01 - 20). talk The phone automatically dials the number shown. 8159620 Memory Search You can search all 20 Memory Locations to find the number you need. Once you - Uniden ANA9610 | English Owners Manual - Page 38
Press vol or chan until you reach the desired Memory Location. 4. Once you have the desired number, press talk. The talk icon appears. The phone will then automatically dial the number. MEMORY NO.20> 9876543210 9876543210 talk Chain Dialing You can dial any stored number while you are on a call - Uniden ANA9610 | English Owners Manual - Page 39
Handset is connected to a call. 1 2 3 Using the Hold The hold button (1) is used in conjunction with a desk top phone to switch from the Handset to a desk top phone. 1. If you need to use a desk top phone which the ANA 9610 is connected to, press hold on the Base unit then pick up the desk top - Uniden ANA9610 | English Owners Manual - Page 40
The optional Head Set provides a "Hands-Free" Option for the ANA 9610. With the Head Set installed, you can use the Belt Clip Jack and plug the Head Set in. No other settings are needed. Operation of the ANA 9610 using the Head Set is exactly the same as using the Handset. However, you will - Uniden ANA9610 | English Owners Manual - Page 41
in case of AC Power failure. The Backup Adapter contains a Battery Pack that provides enough power for you to complete the call and hang up. To install the Backup Adapter: 1. Disconnect the Standard AC Adapter from the Base Unit of the ANA 9610. 2. Plug the AC Adapter into the jack of the EXP9505 - Uniden ANA9610 | English Owners Manual - Page 42
be used with the ANA 9610. Calls can then be answered with the Desk phone and transferred to the ANA 9610. Note:A special Security Feature disconnects the Desk phone whenever the ANA 9610 Handset is in use. Connecting the Desk Telephone. Connect a telephone cord from the Desk phone to the LINE OUT - Uniden ANA9610 | English Owners Manual - Page 43
You can have your PBX system programmed so the following sequence occurs: 1. Your PBX telephone rings first. 2. If you don't answer the PBX telephone after a set number of rings, the call is automatically transferred to the ANA 9610. 3. If you don't answer the call after a set number of rings, it is - Uniden ANA9610 | English Owners Manual - Page 44
Optional Accessories and Replacement Parts contact your PBX Administrator. AC Adapter Telephone Cord Belt Clip EXP9602 Operating R Guide Backup AC Adapter EXP9505 500 mAh Battery BT-9000 Operating Guide OMANA 9610 Base Unit Wall Mount EXP9660 Head Set EXP9530 Charger and AC Adapter - Uniden ANA9610 | English Owners Manual - Page 45
Troubleshooting If your ANA 9610 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your PBX Administrator. Note: Do not attempt to service this unit yourself. All service must be done by qualified - Uniden ANA9610 | English Owners Manual - Page 46
Specifications General: The ANA 9610 complies with FCC and IC parts 15 and 68. Frequency Control Requirements : Rechargeable Sealed Lead Acid Battery Pack Size : 2 1/4 in. W x 1 1/2 in. D x 8 1/2 in. H with antenna Weight : Approx. 8.8 oz. with battery Battery : Capacity 500 mAH, 4.0V
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
 |
 |
ANA 9610
900 MHz Analog
PBX
Cordless Telephone
Operating Guide
®