Uniden LIGHTCAM40HD English Owner Manual
Uniden LIGHTCAM40HD Manual
 |
View all Uniden LIGHTCAM40HD manuals
Add to My Manuals
Save this manual to your list of manuals |
Uniden LIGHTCAM40HD manual content summary:
- Uniden LIGHTCAM40HD | English Owner Manual - Page 1
LightCam 40HD Installation Guide © 2018 Uniden America Corporation Irving, Texas Issue 1, July 2018 Printed in China - Uniden LIGHTCAM40HD | English Owner Manual - Page 2
for warranty. Quickly find answers to your questions by: 1. Reading your owner's manual. 2. Visiting our customer support website at www. uniden.com. Images in this manual may differ slightly from your actual product. Uniden surveillance products are not manufactured and/ or sold with the intent to - Uniden LIGHTCAM40HD | English Owner Manual - Page 3
CONTENTS CUSTOMER CARE 2 OVERVIEW 5 REQUIREMENTS 5 WHAT'S IN THE BOX 5 PARTS OF THE LIGHTCAM 40HD..........6 INSTALL THE CAMERA 6 CONSIDERATIONS 6 PROCEDURES 6 FCC/INDUSTRY CANADA INFORMATION 9 FCC PART 15/IC COMPLIANCE 9 - Uniden LIGHTCAM40HD | English Owner Manual - Page 4
- Uniden LIGHTCAM40HD | English Owner Manual - Page 5
UNIDEN LIGHTCAM 40HD INSTALLATION MANUAL OVERVIEW Thanks for choosing Uniden LightCam 40 HD spotlight camera. This Installation Guide provides basic hardware installation and setup information so you can quickly get your system installed and for further setup. Download the Quick Start Guide from www - Uniden LIGHTCAM40HD | English Owner Manual - Page 6
IR Light Status Indicator LED Screw Locations Motion Sensor INSTALL THE CAMERA Install the LightCam 40HD in a verticle (from the ceiling or eaves) or horizontal (against a wall) position. Installation instructions are identical for either position. CONSIDERATIONS xx If there is no junction box - Uniden LIGHTCAM40HD | English Owner Manual - Page 7
WARNING: TURN POWER OFF AT THE CIRCUIT BREAKER OR FUSE BOX. DO NOT ASSUME TURNING POWER OFF AT A WALL SWITCH WILL TURN OFF ALL POWER TO THE AREA YOU NEED. 2. Pull wires from mounting location (ceiling/eaves, wall, etc). 3. Pull the camera wires through the gasket; press gasket flush to mounting base - Uniden LIGHTCAM40HD | English Owner Manual - Page 8
7. Position the camera roughly where you want it. Tighten the adjustment collar. 8. Loosen the small adjustment screw on the side of the stand. Fine-tune the camera position and then tighten the screw. Again, do not over-tighten. Adjustment Screw 9. Caulk edge of mounting base with silicone weather- - Uniden LIGHTCAM40HD | English Owner Manual - Page 9
an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product - Uniden LIGHTCAM40HD | English Owner Manual - Page 10
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the prepaid, by traceable means, to warrantor at: Uniden America Service C/O Saddle Creek 743 Henrietta Creek Rd. , Suite 100 Roanoke, TX 76262 - - Uniden LIGHTCAM40HD | English Owner Manual - Page 11
- Uniden LIGHTCAM40HD | English Owner Manual - Page 12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
LightCam 40HD
Installation Guide
© 2018 Uniden America Corporation
Irving, Texas
Issue 1, July 2018
Printed in China