Uniden SC150B English Owners Manual - Page 10

Setup, Charging the Battery Pack, Mounting the Flexible Antenna - power supply

Get Uniden SC150B PDF manuals and user guides View all Uniden SC150B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Setup The SportCat comes with a rechargeable Nickel-Cadmium Battery Pack. When fully charged, this Battery Pack will supply up to 12 hours of dependable use. (With the Squelch control in "closed" position.) Before using the SportCat for the first time, or whenever the LOW BATTERY Indicator appears on the LCD display, you should fully charge the Battery Pack. Note: When the Battery Pack is low, the Low Battery Indicator will start to blink. After about 10 minutes, the scanner will shut itself off to prevent the battery from becoming completely discharged. Before charging, you must first install the Battery Pack according to the steps below. Charging the Battery Pack 1. Plug the AC Adapter/Charger (AD-70U) into the Charging Jack located on the Left side of the SportCat. You can use the scanner while it is charging.) WARNING! Use only the supplied AC Adapter/ Charger. Any other AC adapter or external power plug having over-voltage or reversed polarity can cause overheating or damage to the circuitry. 2. Plug the AC Adapter/Charger into a standard AC outlet. To fully charge the battery, leave the Adapter/Charger connected for 14 to 16 hours. 3. When charging is complete, disconnect the Adapter/ Charger from the AC outlet and from the Battery Pack. Note: Disconnect the AC Adapter/Charger from the unit during a power failure. Mounting the Flexible Antenna Place the end of the antenna onto the BNC connector on top of the scanner and turn clockwise until tight. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
Setup
The SportCat comes with a rechargeable Nickel-Cadmium
Battery Pack. When fully charged, this Battery Pack will
supply up to 12 hours of dependable use. (With the
Squelch control in “closed” position.)
Before using the SportCat for the first time, or whenever
the LOW BATTERY Indicator appears on the LCD display,
you should fully charge the Battery Pack.
Note:
When the Battery Pack is low, the Low Battery
Indicator will start to blink. After about 10 minutes, the
scanner will shut itself off to prevent the battery from
becoming completely discharged.
Before charging, you must first install the Battery Pack
according to the steps below.
Charging the Battery Pack
1.
Plug the AC Adapter/Charger (AD-70U) into the
Charging Jack located on the Left side of the SportCat.
You can use the scanner while it is charging.)
WARNING!
Use only the supplied AC Adapter/
Charger. Any other AC adapter or external power
plug having over-voltage or reversed polarity can
cause overheating or damage to the circuitry.
2.
Plug the AC Adapter/Charger into a standard AC
outlet.
To fully charge the battery, leave the Adapter/Charger
connected for 14 to 16 hours.
3.
When charging is complete, disconnect the Adapter/
Charger from the AC outlet and from the Battery Pack.
Note:
Disconnect the AC Adapter/Charger from the unit
during a power failure.
Mounting the Flexible Antenna
Place the end of the antenna onto the BNC connector on
top of the scanner and turn clockwise until tight.
10