Uniden SCP1 Owner s Manual

Uniden SCP1 Manual

Get Uniden SCP1 PDF manuals and user guides View all Uniden SCP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Uniden SCP1 manual content summary:

  • Uniden SCP1 | Owner s Manual - Page 1
    AppCam Solo Quick Start Guide
  • Uniden SCP1 | Owner s Manual - Page 2
    What's in the Box AppCam Solo Camera x1 Reset Needle x1 Magnetic Mount x1 Screw Mount x1 CR123A CR 123A Batteries Screws (in pack) x4 x1 Opener x1 2 General Introduction Micro SD Card Slot Reset Button Daylight Sensor Lens Status LED Built-in Mic Built-in PIR Motion Sensor Speaker
  • Uniden SCP1 | Owner s Manual - Page 3
    remove the batteries from camera to avoid corrosion. Uniden AppCam Solo Supports • 3V CR123A non-rechargeable batteries • 3.6V~4.2V CR123A rechargeable new set of 4 batteries (the standard batteries we provide) will support up to 180 days in standby mode, or 800 minutes (IR LEDs off in daytime
  • Uniden SCP1 | Owner s Manual - Page 4
    . Set up the Camera Please follow the prompt tone to configure the camera Please run App. Click the "Add New Device" button, and follow the instructions to set up the camera. 1. Please click the " '' button in the top right corner to add the camera. 6 2. Scan QR code on the camera. 3. Click
  • Uniden SCP1 | Owner s Manual - Page 5
    4. Click the button "I have heard the voice prompt" to enter the next page. If you did not hear the voice prompt, please press "I did not hear the voice prompt" for help. 5. Enter the Wi-Fi password of the selected Wi-Fi network and press "I have entered the correct information" to enter the next
  • Uniden SCP1 | Owner s Manual - Page 6
    Wi-Fi connection failed! Please check the Wi-Fi settings and try again. 7. If you hear the above voice prompt, please press "I heard 'Wi-Fi connection failed' " for help. Wi-Fi connection succeeds! 8. If you hear the above voice prompt, please press "I heard 'Wi-Fi connection succeeds' " to finish
  • Uniden SCP1 | Owner s Manual - Page 7
    Device Menu 10. Please tap the camera and follow the steps to sync the time, and then start live view or go to "Device Settings" for more configurations. Menu Add New Device Enable/Disable PIR Motion Sensor (in default, the PIR sensor is enabled). Device Settings Access the Live View Battery Status
  • Uniden SCP1 | Owner s Manual - Page 8
    ! Important Notes for Reducing False Alarms For reducing false alarms, please note: • Do not install the camera facing any objects with bright lights, including sunshine, bright lamplights, etc. • Do not install the camera in a place within 15 meters where there are frequently moving vehicles. •
  • Uniden SCP1 | Owner s Manual - Page 9
    How to Install How to Install (using screw moun(uts)ing screw mount) Wall Mount Wall Mount 1 Front 2 Back Tree Mount Tree Mount How to Remove Step 1: Step 1: Step 2: Step 2: Step 1: Step 1: Screw the security mounStcprelawtethe seLcautcrihtytmheousnetcpulraittey mounLtaotnchittshe security
  • Uniden SCP1 | Owner s Manual - Page 10
    the owner's manual for this product. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are the defective unit & return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by warrantor
  • Uniden SCP1 | Owner s Manual - Page 11
    uniden.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
AppCam Solo
Quick Start Guide