ViewSonic N3251W User Manual - Page 22

ENTER, Cancel, Channel Lock, Change Password, Clear All, Color Temperature, Back Light, Aspect Ratio - menu locked

Get ViewSonic N3251W PDF manuals and user guides View all ViewSonic N3251W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

When you enter this control, the screen below will be displayed. The factory default of the password is "0000". To enable parental control, input the password, press ▼ button to focus on "ok" key, and press ENTER. (select Cancel if you want to exit) After entering, the following screen will be shown. ENGLISH Channel Lock: To lock channels. Use ◄► to select the channel you want to lock, and then press ENTER to lock or unlock it. Change Password: To change the password, press ENTER and enter the password again. Press ENTER, and the following screen appears. Enter the new password, use ▼ to move the cursor down, and then enter the new password again, press OK to confirm or Cancel to exit. Note: Please make sure you remember your new password after changing, because you cannot recall the default setting of the password by any selection. Clear All: To clear all the locks set before, press ENTER. Press MENU to return to the previous page. • Color Temperature: To select the color temperature from Warm, Cold, Normal or User. (If you select User, you can adjust the degree of R, G, B in Color Temp. to suit your personal preference.) • Back Light: To adjust the luminance of the back light. • Aspect Ratio: To select image size between Normal, Full, Wide1, Wide2, Wide3, 4:3, 16:9, and No scale. • OSD Timeout: To setup the display time of OSD. (5, 15, 45, and 60 seconds) • Memory Recall: To restore the factory default settings. ViewSonic 20 N3251w

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
ViewSonic
N3251w
20
ENGLISH
When you enter this control, the screen below will be displayed.
The factory default of the password is “0000”.
To enable parental control, input the password, press ▼ button to focus on “ok” key, and
press
ENTER
. (select
Cancel
if you want to exit)
After entering, the following screen will be shown.
Channel Lock:
To lock channels. Use ◄► to select the channel you want to lock, and
then press
ENTER
to lock or unlock it.
Change Password:
To change the password, press
ENTER
and enter the password again.
Press
ENTER
, and the following screen appears.
Enter the new password, use ▼ to move the cursor down, and then enter the new
password again, press
OK
to confirm or
Cancel
to exit.
Note:
Please make sure you remember your new password after changing, because you
cannot recall the default setting of the password by any selection.
Clear All:
To clear all the locks set before, press
ENTER
.
Press
MENU
to return to the previous page.
•
Color Temperature:
To select the color temperature from Warm, Cold, Normal or User.
(If you select User, you can adjust the degree of R, G, B in Color Temp. to suit your
personal preference.)
•
Back Light:
To adjust the luminance of the back light.
•
Aspect Ratio:
To select image size between Normal, Full, Wide1, Wide2, Wide3, 4:3,
16:9, and No scale.
•
OSD Timeout:
To setup the display time of OSD. (5, 15, 45, and 60 seconds)
•
Memory Recall:
To restore the factory default settings.