ViewSonic PJ-WMK-304 Quick Start Guide
ViewSonic PJ-WMK-304 Manual
 |
View all ViewSonic PJ-WMK-304 manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic PJ-WMK-304 manual content summary:
- ViewSonic PJ-WMK-304 | Quick Start Guide - Page 1
PJ-WMK-304 Quick Start Guide Important Safety Informa�on 1. Please read this manual a qualified service personnel immediately. supports ViewSonic® projectors and models that are designated by ViewSonic. Use with non-ViewSonic branded projectors or exceeding the weight capacity is neither supported
-
1
 |
 |
PJ-WMK-304
Quick Start Guide
Important Safety Informa�on
中国
电话：
4008 988 188
香港
電話：
852 3102 2900
澳門
電話：
853 2833 8407
台灣
電話：
0800 899 880
한국
Phone: 080 333 2131
Singapore/Malaysia/Thailand
Phone: 65 6461 6044
India
Phone: 1800-419-0959
United States
Phone: 1-800-688-6688
Canada
Phone: 1-866-463-4775
Europe
Australia/New Zealand
Phone: 1800 880 818 (AUS)
0800 008 822 (NZ)
South Africa
Latin America (Chile)
Latin America (Mexico)
Latin America (Peru)
Latin America (Argentina)
Puerto Rico & Virgin Islands
Phone: 1-800-688-6688 (English)
PJ-WMK-304_QSG_Rev. 1c 12-10-20
Copyright © 2021 ViewSonic Corporation. All rights reserved.
1.
Please read this manual carefully and follow all safety rules before installa�on.
2. For safety reasons, please make sure the wall is strong enough to sustain the weight of the
projector & wall mount.
3. The total maximum weight of all items mounted should NEVER exceed the weight capacity: 55 lbs
(25kg).
4.
DO NOT a±empt to alter or modify any part of the wall mount or its a±achments.
5.
Do not install the projector wall mount on a structure that is prone to vibra�on, movement or
chance of impact.
6.
To avoid risk of fire, do not install the projector with the projector wall mount in a humid or
excessively dusty place.
7. Use the supplied accessories only. Use of accessories other than those supplied may result in
damage to the projector and/or projector wall mount.
8. Unplug the AC power cord and any other connected cables before dismounting the projector from
the projector wall mount.
9. Do not hit or hang any heavy objects on the projector wall mount. If the projector wall mount is
damaged, stop using immediately and contact a qualified service personnel immediately.
10. Only install the projector wall mount horizontally on the level surfaces.
* The manufacturer is not liable for any damages or injury caused by mishandling or improper
installa�on.
11. The projector or wall mount may fall and cause personal injury. Ensure screws are tightened to the
proper torque after installation and any adjustments. Do not overtighten screws as this may cause
screw deformation.
12. This wall mount kit ONLY supports ViewSonic® projectors and models that are designated by
ViewSonic. Use with non-ViewSonic branded projectors or exceeding the weight capacity is
neither supported nor recommended, may cause property damage or personal injury, and shall be
at the sole risk of users/installers.
Checking The Supplied Accessories
Setting The Projector Wall Mount On The Wall
• The bracket is suitable for concrete wall mounting or wooden stud wall.
• Concrete wall mounting thickness must be a minimum 4” (100mm). Anchor bolt and
screw (M6 × 55) are needed
to be used for concrete wall installation.
• Dry-wall wall
thickness must be a minimum 4.5” (114mm). Only screw (M6 × 55) is
needed to be used for installation, and gypsum board thickness less than 0.59"
(15mm).
If the wall is not strong enough, reinforce it sufficiently before installation.
• Please contact reseller if you have any questions about mounting surface issue.
Adjusting The Image Height
Adjusting The Horizontal Rotation
Adjusting The Vertical Tilt
Placing The Decorative Cover
Product Information
Adjusting The Horizontal Roll
Note:
When all adjustments are completed, the wall plate covers can be used to cover
the blank area on the top of wall plate. Finally, put the wall cover on.
1
2
3
5
4
7
8
6
Projector Mounting
Plate X 1
A
B
C
D
E
F
G
H
I
Projector Mounting
Arms x4
Fixed Support Arm x1
Wall Plate x1
Wall Cover x1
Wall Plate Cover x1
Loosen the screw
Take off the cap
A
A
B
B
Tighten the screw G when
the height is determined.
C
G
Slide the mounting plate
A
B
Slide the mount
Slide the mount to
adjust the image size
The cable
Loosen the screws with L3 allen wrench,
pull out the support arm around
4'' (100mm)
The cables can be got through the wall plate
The
cables
C
G
The
cables
C
>55mm
B
Concrete wall mounting
With anchor bolt
>55mm
Ø
3mm
Dry-wall mounting
Without anchor bolt
Ø10-11mm
(2.17")
(0.39"-0.43")
(2.17")
(0.12")
When installation on the
wood stud wall, Align the
center of the wall mount
plate with the center of
the stud.
screw central point
screw (M6 x55) are needed
for installation in dry-wall mounting
C
A
A
The arrows up
The arrows up
screw (M6 x55) are needed
for installation in concrete wall mounting
Installing The Projector On The Projector Wall Mount
A
Screen
Adjustment
Direction
B
A
B
A
Screen
B
Adjustment
Direction
to see the distance from
wall to the mounting plate
Check the scale plate
Screen Adjustment Direction
Vertical Tilt Knob
D
G
A
B
A
B
A
B
Screen Adjustment Direction
Screen Adjustment Direction
A
B
Horizontal Roll Knob
Horizontal Rotation Knob
1
2
3
4
or
1
1
2
1
2
3
9.9 lb (4.5 kg)
PJ-WMK-304
Model
Net Weight
Weight Capacity
Extendable Length
Adjustment Angle
55lb (25.0 kg)
14.4"-25"(365-635mm)
Vertical tilt, Horizontal roll, Horizontal rotation ±5°
Adjusting The Image Size
E
I
F
F
H
E
E
Use
Connecting
screws I
M6
M4
Screw E & I Tightening torque: 8kgf-cm (
≦
12kgf-cm)
Screw hole
on projector
(Optional for M6
hole on projector)