ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio |
ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio Manual
View all ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio manual content summary:
- ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 1
a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found su equipo lea cu idadosamente las instrucciones en este manual" Model No. VS15875/VS15876 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 2
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world's expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 3
. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 4
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 5
ventilation openings. Install the unit in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 6
Copyright Information Copyright © ViewSonic Corporation, 2017. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 7
product will best prepare you for future customer service needs. Please print this user guide and fill the information in the "For Your Records" section. For additional information, please see the "Customer Support" section in this guide. Product Name: Model Number: Document Number: Serial Number - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 8
Table of contents Important safety instructions 2 Introduction 4 Projector features 4 Shipping contents 5 Projector exterior view 6 Using the dust filter (optional accessory 47 Lamp information 48 Troubleshooting 52 Specifications 53 Projector specifications 53 Dimensions 55 Ceiling mount - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 9
the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. 3. Refer servicing to qualified service personnel. 4. Always open - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 10
the power supply's wall socket and call your local service center to have the projector serviced. 18. This product is capable of displaying inverted It should be used with a commercially available theft prevention cable. Safety instructions for ceiling mounting of the projector We want you to have a - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 11
70% when no input signal can be detected for a set period of time. • Presentation timer for better control of time during presentations • Supports 3D display • Supports Blu-ray 3D display (for models with HDMI input) • Color Management allowing color adjustments to your liking • Less than 0.5W power - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 12
be suitable for your region, and may differ from those illustrated. Projector Power Cord VGA Cable Multi-language User Manual CD Quick Start Guide Remote Control & Batteries Optional accessories 1. Replacement lamp (RLC-092 for PJD5353LS. RLC-093 for PJD5553LWS.) 2. Soft carry case 3. VGA - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 13
Projector exterior view Front/upper side 1 6 2 3 4 5 7 8 Rear/lower side 9 10 11 12 13 14 15 16 17 18 19 20 1. External control panel (See "Projector" on page 7 for details.) 2. Lamp cover 3. Vent (heated air exhaust) 4. Front IR remote sensor 5. Adjuster foot 6. Focus ring 7. Projection - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 14
status of the lamp. Lights up or flashes when the lamp has developed a problem. 12. (Panel Key Lock) Activates or disables panel key lock by a keys are used as directional arrows to 7. / (Keystone keys) Manually corrects distorted images select the desired menu items and to make adjustments. - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 15
Performs the same function as the right mouse button when the mouse mode is activated. Only available when a PC input signal is selected. Manually corrects distorted images resulting from an angled projection. 5. Left/ Right/ Up/ Down Selects the desired menu items and makes adjustments. 8 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 16
10. Mouse 19. Exit Switches between the normal and mouse modes. Goes back to previous OSD menu, exits and saves menu settings. PgUp, PgDn, , : active after pressing 20. PgUp (Page Up)/PgDn (Page Down) Mouse. An icon appears on the screen to Operates your display software program indicate the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 17
Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer's mouse. See " - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 18
• Replace only with the same or equivalent type recommended by the battery manufacturer. • Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • Never throw the batteries into a fire. There may be danger of an explosion. • If - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 19
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 20
below refers to the projection screen usually consisting of a screen surface and a support structure. PJD5353LS • 4:3 image on a 4:3 screen (b) (a) (d) (c) (f) (e) (a) (c) (d) (e) (f) (b) • 16:9 image on a 4:3 screen (b) (a) (d) (a) (e) (f) (c) (e): Screen (c) (f) (e) (f): Center of - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 21
PJD5553LWS • 16:10 image on a 16:10 screen (b) (a) (d) (c) (f) (e) • 16:10 image on a 4:3 screen (b) (a) (d) (e): Screen (c) (f) (e) (f): Center of lens (a) (e) (f) (c) (d) (b) (a) (e) (f) (c) (d) (b) (a) Screen Size [inch (m)] 16:10 image on a 16:10 Screen (b) Projection distance [m (inch)] - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 22
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 23
the screen, you can connect the MONITOR OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below: 1. Connect the projector to a computer as described in "Connecting a computer" on page 16. 2. Take a suitable VGA cable (only one supplied) and - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 24
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 25
If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector. Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 26
If you have already made a Component Video connection between the projector and this SVideo source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 27
Ring Tone" on page 35 for details. 4. If the projector is activated for the first time, select your OSD language following the on-screen instructions. 5. Switch all of the connected equipment on. 6. The projector will start to search for input signals. The current input signal being scanned appears - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 28
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Sub-menu Current input - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 29
the message 'INPUT PASSWORD' follows. You can retry by entering another six-digit password, or if you did not record the password in this user manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 23 for - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 30
3 seconds. The projector will display a coded number on the screen. 2. Write down the number and turn off your projector. 3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 31
the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. Press - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 32
• Normal: Sets the HDMI color range as 15 - 235. • Auto: Sets the projector to detect the HDMI range of the input signal automatically. This function is only available when the HDMI input port is in use. Refer to the documentation of the device for information on the color space and HDMI range - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 33
when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / to display the Keystone correction page. Press to correct keystoning at - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 34
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 35
5. Wide (PJD5553LWS): Scales a 4:3 aspect image vertically and horizontally in a non-linear manner so that it fills the screen with a 16:10 aspect ratio. 4:3 picture 6. Panorama (PJD5353LS): Scales a 4:3 image vertically and horizontally in a non-linear manner so that it fills the screen.. 4:3 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 36
3. Standard mode: Is designed for presentations under daylight environment to match PC and notebook coloring. 4. ViewMatch mode: Switches between high brightness performance and accurate color performance. 5. Movie mode: Is appropriate for playing colorful movies, video clips from digital cameras or - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 37
Adjusting Brilliant Color Go to the PICTURE > Advanced > Brilliant Color menu and press / . This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in the projected picture. It enables a greater than - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 38
Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 39
3. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments. If the timer is already on, the timer will restart whenever the Timer Period is reset. 4. Press to highlight - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 40
Hiding the image In order to draw the audience's full attention to the presenter, you can press Blank to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden. You can - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 41
harsh or extreme conditions. Using the CEC function This projector supports CEC (Consumer Electronics Control) function for synchronized power on in 3D format automatically. In other cases, you may need to manually select a 3D Sync format for the projector to project 3D images correctly problem. 34 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 42
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure you have turned on the corresponding menus under SOURCE > Standby Settings, and the cable connections are correctly made. For the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 43
Shutting down the projector 1. Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press Power a second time. 3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 44
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 45
Main menu Sub-menu Options 3. SOURCE 4. SYSTEM SETTING: BASIC Quick Auto Search Off/On 3D Settings 3D Sync Auto/Off/Frame Sequential/ Frame Packing/Top-Bottom/ Side-By-Side 3D Sync Invert Disable/Invert Standby Settings Active VGA Out Active Audio Out Off/On Off/On Computer Disable/ - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 46
Main menu Sub-menu Options High Altitude Mode On/Off DCR On/Off Mute On/Off Audio Settings Audio Volume Power On/Off Ring Tone On/Off Closed Caption Off/CC1/CC2/CC3/CC4 5. SYSTEM SETTING: ADVANCED Lamp Settings Lamp Mode Reset Lamp Hours Lamp Hours Filter Mode Normal/Economic/ - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 47
Description of each menu 1. DISPLAY menu Function Screen Color Aspect Ratio Keystone Position Phase Description See "Using Screen Color" on page 29 for details. This function is only available when a PC input signal is selected. See "Selecting the aspect ratio" on page 27 for details. See " - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 48
2. PICTURE menu Function Description Color See "Adjusting Color" on page 29 for details. Tint See "Adjusting Tint" on page 29 for details. This function is only available when a Composite video or S-Video input signal with NTSC system is selected. Advanced Sharpness See "Adjusting Sharpness" - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 49
3. SOURCE menu Function Description Auto Power Off Smart Restart Power Saving See "Setting Power Saving" on page 48 for details. Sleep Timer See "Setting Sleep Timer" on page 48 for details. Selecting Enable enables you to restart the projector immediately within 120 seconds after turning it off - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 50
4. SYSTEM SETTING: BASIC menu Function Splash Screen My Button Advanced High Altitude Mode DCR Description Allows you to select which screen will be displayed during projector start-up. Sets a hotkey on remote control. Pattern The projector can display several test patterns. It helps you adjust - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 51
Economic" on page 48 for details. Reset Lamp Hours Resets the lamp timer after new lamp is installed. For changing the lamp, please contact qualified service personnel. Lamp Hours See "Getting to know the lamp hour" on page 48 for details on how the total lamp hour is calculated. See "Using - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 52
6. INFORMATION menu Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. Current System Color System Status Shows input system format. Lamp Hours Displays the number - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 53
detergents. These can damage the case. Storing the projector If you need to store the projector for an extended time, please follow the instructions below: • Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 54
Using the dust filter (optional accessory) CAUTION • It is important to clean the dust filter every 100 hours after the dust filter is installed. • Be sure to turn off the projector and unplug it from power source before installing or detaching the filter. • If your projector is ceiling-mounted or - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 55
8. Highlight Reset and press Enter. The lamp time will be reset to '0'. CAUTION Remember to set Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer. The timer will - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 56
operate normally. Notice Replace Lamp Now Lamp > ____ Hours Lamp usage time exceeded OK Notice Out of Lamp Usage Time Replace lamp (refer to User Manual) Then reset lamp timer OK 49 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 57
Replacing the lamp Turn the power off and disconnect the projector from the power outlet. Please contact qualified service personnel for changing the lamp. Type number for the replacement lamp: • PJD5353LS: RLC-092 • PJD5553LWS: RLC-093 50 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 58
Indicators Light Status & Description Power events Blue Flashing Off Blue Off Blue Off Blue Flashing Off Red Off Off Stand-by mode Off Powering up Off Normal operation Off Normal power-down cooling (3 sec) Off Downloading Lamp events Blue Flashing Off Off Off Blue Off Purple - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 59
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Attempting to turn the projector on again during the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 60
Specifications Projector specifications • All specifications are subject to change without notice. • Not all models can be purchased in your region. General Product name DLP Projector Optical Resolution PJD5353LS: 1024 x 768 XGA Display system Lamp PJD5553LWS: 1280 x 800 WXGA 1-CHIP DMD - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 61
Output terminal RGB output Audio signal output Speaker D-Sub 15-pin (female) x 1 Audio jack x 1 2 watt x 1 Control terminal RS-232 serial control LAN USB serial control IR receiver 9 pin x 1 N/A Type mini B x 1 (Front) Environmental Requirements Operating temperature Operating relative - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 62
Timing chart Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ UXGA WSXGA+ HD MAC 13" MAC 16" MAC 19" MAC 21" Analog RGB Resolution (dots) Aspect Ratio 640 x 480 4:3 800 x 600 4:3 1024 x 768 4:3 1152 x 864 4:3 1280 x 768 15:9 1280 x 800 16:10 1360 x 768 16:9 1280 x 960 4:3 1280 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 63
Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ WSXGA+ HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV (480p) SDTV (576p) SDTV (480i) SDTV (576i) HDMI Resolution (dots) Aspect Ratio 640 x 480 4:3 800 x 600 4:3 1024 x 768 4:3 1280 x 768 15:9 1280 x 800 16:10 1360 x 768 16:9 1280 x 960 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 64
for Side-By-Side, Top-Bottom, and Frame Sequential formats. ** 120 Hz signals are supported for Frame Sequential format only. *** Video signal (SDTV 480i) is supported for Frame Sequential format only. In Frame packing format Signal 1080p 720p In Side by side format Signal 1080i In Top and - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 65
Signal HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV (480p) SDTV (576p) SDTV (480i) SDTV (576i) Signal NTSC PAL PAL60 SECAM Component video Resolution (dots) Aspect Ratio 1920 x 1080 16:9 1920 x 1080 16:9 1280 x 720 16:9 720 x 480 4:3 / 16:9 720 x 576 4:3 / 16:9 720 x 480 4:3 / 16:9 720 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 66
or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic Corporation makes no representations or warranties, either - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 67
Appendix IR control table Key PgDn PgUp Blank Auto sync Up Down Left Right Color Mode Enter Power ON Magnify Presentation Timer Exit D. ECO (Eco mode) Menu Mouse Mouse Left Mouse Right Source Pattern My button HDMI Volume+ VolumeKey pad lock VGA1 VGA2 Help 3D Format NEC NEC NEC NEC NEC NEC NEC NEC - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 68
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin 1 3 5 7 9 Description NC TX GND RTSZ NC Baud Rate Data Length Parity Check Stop Bit Flow Control - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 69
Function Status Action Power Write Read Turn on Turn off Power status (on/off) Reset all settings Execute Reset Color Settings Execute Splash Screen Black Splash Screen Blue Splash Screen Write Splash Screen ViewSonic Splash Screen Screen Capture Splash Screen - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 70
Message Projector Position 3D Sync 3D Sync Invert Contrast Brightness Write Read Write Read Write Read Write Read Write Read Write Read Message Off Message On Message status Front Table Rear Table Rear Ceiling Front Ceiling projector position status OFF Auto Frame Sequential Frame Packing Top- - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 71
Aspect ratio Auto Adjust Horizontal position Vertical position Write Aspect ratio Auto Aspect ratio 4:3 Aspect ratio 16:9 Aspect ratio 16:10 Aspect ratio Anamorphic Aspect ratio Wide Aspect ratio 2.35:1 Aspect ratio Panorama Read Aspect ratio Execute Write Horizontal position shift right - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 72
Color temperature Write Read Blank Write Read KeystoneVertical Write Read KeystoneHorizontal Write Read Color mode Write Read color temperature Warm color temperature Normal color temperature Neutral color temperature Cool color temperature status Blank on Blank off Blank status Decrease - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 73
Primary Color Hue Saturation Gain Freeze Write Read Write Read Write Read Write Read Write Read Primary color R Primary color G Primary color B Primary color C Primary color M Primary color Y Primary color status Hue decrease Hue increase Hue Saturation decrease Saturation increase Saturation Gain - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 74
Source input Quick Auto Search Mute Volume Write Read Write Read Write Read Write Read Input source VGA Input source VGA2 Input source HDMI Input source Composite Input source SVIDEO Source Quick Auto Search on Quick Auto Search off Quick Auto Search status Mute on Mute off Mute status Increase - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 75
Language Write Read Lamp Time Write Read 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 76
HDMI Format HDMI Range CEC Error status Brilliant Color Write Read Write Read Write Read Read Write Read RGB YUV Auto HDMI Format status Enhanced Normal Auto HDMI Range status Off On CEC status Read error status Brilliant Color 0 Brilliant Color 1 Brilliant Color 2 Brilliant Color 3 Brilliant - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 77
Remote Control code Screen Color Over Scan Write Read Write Read Write Read code 1 code 2 code 3 code 4 code 5 code 6 code 7 code 8 Remote Control code status Screen color Off Blackboard Greenboard Whiteboard Screen Color status Overscan Off Overscan 1 Overscan 2 Overscan 3 Overscan 4 Overscan 5 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 78
Remote Key Write Menu Exit Up Down Left Right Source Enter Auto My Button 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E 0x02 0x14 0x00 0x04 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 79
New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 [email protected] Canada www.viewsonic.com T= 1-866-463-4775 [email protected] Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 80
acts of nature, improper maintenance, unauthorized product modification, or failure to follow instructions supplied with the product. b. Operation outside of product specifications. c. Operation of defect. 3. Removal, installation, one way transportation, insurance, and set-up service charges. - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 81
ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial number. 2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 82
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product. b. Any damage of the service charges. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 83
39300 Acapulco, Guerrero Tel: 744-48-32627 Monterrey: Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico FOR USA SUPPORT: ViewSonic Corporation 14035 Pipeline Ave. Chino, CA 91710, USA Tel: 800-688 - ViewSonic PJD5353LS - 1024 x 768 Resolution 3 200 ANSI Lumens 0.61 Throw Ratio | - Page 84
PJD5353LS/PJD5553LWS
DLP Projector
User Guide
Model No. VS15875/VS15876
IMPORTANT:
Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service.
Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
±±±²³´µ±¶·¸´¹²¹·º»´¸»¼¸½¾´¶¿À»·Á»´¸»¶Âµ¹´Ã¹»¾Ä¸½ÅĽµ¶»Å¶´¸½»Æ¿µ»Çµ½´·¸Ä¾»¶µ¾µ¹Æ´·¸»
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”