ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio |
ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio Manual
View all ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio manual content summary:
- ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 1
manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which las instrucciones en este manual" Model No. VS15877/VS15878/VS15947/VS15948/VS15879/ VS15880/VS15949/VS15950 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 2
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world's expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 3
. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 4
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 5
ventilation openings. Install the unit in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 6
Copyright Information Copyright © ViewSonic Corporation, 2017. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 7
product will best prepare you for future customer service needs. Please print this user guide and fill the information in the "For Your Records" section. For additional information, please see the "Customer Support" section in this guide. Product Name: Model Number: Document Number: Serial Number - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 8
Table of contents Important safety instructions 2 Introduction 4 Projector features 4 Shipping contents 5 Projector exterior view 6 Using the dust filter (optional accessory 57 Lamp information 59 Troubleshooting 63 Specifications 64 Projector specifications 64 Dimensions 66 Ceiling mount - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 9
the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. 3. Refer servicing to qualified service personnel. 4. Always open - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 10
the power supply's wall socket and call your local service center to have the projector serviced. 18. This product is capable of displaying inverted It should be used with a commercially available theft prevention cable. Safety instructions for ceiling mounting of the projector We want you to have a - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 11
of time. • Presentation timer for better control of time during presentations • LAN Settings allowing management of projector status from a remote computer • Supports 3D display • Color Management allowing color adjustments to your liking • Less than 0.5W power consumption when power saving mode is - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 12
. PJD6350/PJD6352 PJD6550Lw/PJD6552Lw PJD6351Ls/PJD6352Ls PJD6551Lws/PJD6552Lws Projector Power Cord VGA Cable Multi-language User Manual CD Quick Start Guide Remote Control & Batteries Cable management cover Optional accessories 1. Replacement lamp (RLC-092 for PJD6350/PJD6351Ls. RLC - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 13
Projector exterior view Front/upper side PJD6350/PJD6352 PJD6550Lw/PJD6552Lw 1 6 2 3 4 7 5 8 PJD6351Ls/PJD6352Ls PJD6551Lws/PJD6552Lws 1 6 2 3 4 7 5 8 9 Rear/lower side 10 11 12 13 14 15 16 17 18 19 20 21 22 1. External control panel (See "Projector" on page 7 for details.) 2. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 14
the projector is 4. / / / (Keystone keys) under operation. Manually corrects distorted images resulting from an angled projection. Left/ Right/ Up/ or flashes when the lamp has developed a Toggles the projector between standby problem. mode and Power ON. 12. Color Mode 6. Source Selects an - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 15
(Right mouse button) Performs the same function as the right mouse button when the mouse mode is activated. 4. / / / (Keystone keys) Manually corrects distorted images Only available when a PC input signal is selected. resulting from an angled projection. Left/ Right/ Up/ Down Selects the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 16
9. Mouse 18. Exit Switches between the normal and mouse modes. Goes back to previous OSD menu, exits and saves menu settings. PgUp, PgDn, , : active after pressing 19. PgUp (Page Up)/PgDn (Page Down) Mouse. An icon appears on the screen to Operates your display software program indicate the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 17
To switch the code for the remote control, press ID set and the number button corresponding to the remote control code set in the projector OSD together for 5 seconds or more. COMP1 COMP2 HDMI Auto Sync Source The initial code is set to 1. When the code is switched to 8, Enter the remote - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 18
• Replace only with the same or equivalent type recommended by the battery manufacturer. • Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • Never throw the batteries into a fire. There may be danger of an explosion. • If - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 19
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 20
mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. PJD6350/PJD6352/PJD6351Ls/PJD6352Ls • 4:3 image on a 4:3 screen (b) (a) (d) (c) (f) (e) (a) (c) (d) (e) (f) (b) • 16:9 image on a 4:3 screen (b) (a) (d) (a) (e) (f) (c) (e): Screen - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 21
PJD6351Ls/PJD6352Ls (a) Screen Size [inch (m)] 4:3 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] 16:9 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 22
PJD6550Lw/PJD6552Lw/PJD6551Lws/PJD6552Lws • 16:10 image on a 16:10 screen (b) (a) (d) (c) (f) (e) (a) (e) (f) (c) (d) (b) • 16:10 image on a 4:3 screen (a) (e): Screen (b) (d) (c) (f) (e) (f): Center of lens (a) (e) (f) (c) (d) (b) PJD6550Lw/PJD6552Lw (a) Screen Size [inch (m)] 16:10 image - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 23
PJD6551Lws/PJD6552Lws (a) Screen Size [inch (m)] 16:10 image on a 16:10 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] 16:10 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 24
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 25
the screen, you can connect the MONITOR OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below: 1. Connect the projector to a computer as described in "Connecting a computer" on page 18. 2. Take a suitable VGA cable (only one supplied) and - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 26
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 27
If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector. Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 28
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. 1. Take an S-Video cable and - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 29
About the microphone input • If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the projector. • You can use a wireless microphone as long as a wireless module is attached to the projector's microphone input jack and it works well with the associated devices. To ensure a - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 30
Ring Tone" on page 46 for details. 4. If the projector is activated for the first time, select your OSD language following the on-screen instructions. 5. Switch all of the connected equipment on. 6. The projector will start to search for input signals. The current input signal being scanned appears - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 31
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Sub-menu Current input - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 32
the message 'INPUT PASSWORD' follows. You can retry by entering another six-digit password, or if you did not record the password in this user manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 26 for - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 33
3 seconds. The projector will display a coded number on the screen. 2. Write down the number and turn off your projector. 3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 34
the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. Press Source - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 35
• Auto: Sets the projector to detect the color space setting of the input signal automatically. 4. Highlight HDMI Range and press / to select a suitable HDMI color range according to the color range setting of the output device connected. • Enhanced: Sets the HDMI color range as 0 - 255. • Normal: - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 36
, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control keystoning at the left side of the image. Adjusting 4 corners You can manually adjusts the shape and size of an image that is unevenly rectangular on all - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 37
3. Press the button that represents the corner you wish to adjust and press Enter. 4. Press / to select an adjustment method that suits your need and press Enter. 5. Press / / / to adjust its shape and size. During this process, you can press Menu or Exit to go back to a previous step. A long press - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 38
1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to 16:10 picture make most use of the screen without altering the image's aspect ratio. 15:9 picture 2. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 39
8. Anamorphic: Scales a 2.35:1 aspect image so that it fills the screen. 2.35:1 picture Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 40
Adjusting Brightness Go to the PICTURE > Brightness menu and press / . The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible. -30 50 +80 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 41
Go to the PICTURE > Color Temp. menu and press / . The options available for color temperature* settings vary according to the signal type selected. 1. Cool: With the highest color temperature, Cool makes the image appear the most bluish white than other settings. 2. Neutral: Makes images appear - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 42
Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. 5. Press to highlight - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 43
6. Press to highlight Timer Counting Direction and select your desired counting direction by pressing / . Selection Count Up Count Down Description Increases from 0 to the preset time. Decreases from the preset time to 0. 7. Press to highlight Sound Reminder and decide if you want to activate - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 44
Keys on the remote control are still functional when panel key lock is enabled. If you press Power to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on. Creating your own startup screen In addition to selecting the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 45
via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, projects images in 3D format automatically. In other cases, you may need to manually select a 3D Sync format for the projector to project 3D images correctly. problem. 38 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 46
Controlling the projector through a LAN environment The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 47
area network to control the projector. If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher. The screen shots in this manual are for reference only, and may differ from the actual design. 1. Enter the address of the projector in the address bar of your browser and - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 48
If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure Setting Email Alert SMTP Setting Alert Condition Input Length Maximum Number of Characters DHCP/Manual (N/A) IP Address XXX.XXX.XXX.XXX Subnet Mask XXX.XXX.XXX.XXX Gateway - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 49
on this projector. i ii iv iii v vi i. This section is only used with the Crestron Control System. Please contact Creston or refer to its user manual for setup information. 42 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 50
ii. You can name the projector, keep track of its location and the person in charge of it. iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v. Once set, access to the tools page has been password- - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 51
com/products/roomview_connected_embedded_projectors_devices/ resources.asp PJLink™, SNMP, AMX and Xpanel formats supported This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, please follow its user guide or website respectively to control and manage projectors. Using the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 52
Active VGA Out Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT sockets are correctly connected to devices. The projector outputs the signal received only from COMPUTER IN 1. Active Audio Out Selecting On outputs an audio signal when the AUDIO IN 1 socket is correctly - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 53
Adjusting the Audio In 2 setting 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio Settings > Audio In 2 menu. 2. Press / to decide the audio input source for the AUDIO IN 2/MIC port. This will affect the connection method for different devices, and where the sound is from. • When - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 54
Shutting down the projector 1. Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press Power a second time. 3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 55
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 56
Main menu Sub-menu Options 3. SOURCE 4. SYSTEM SETTING: BASIC Quick Auto Search Off/On 3D Settings 3D Sync Auto/Off/Frame Sequential/ Frame Packing/Top-Bottom/ Side-by-Side 3D Sync Invert Disable/Invert Standby Settings Active VGA Out Active Audio Out LAN Control Off/On Off/On Off/On - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 57
Main menu Sub-menu Options Pattern Off/1/2/3 Message On/Off 4. SYSTEM SETTING: BASIC Advanced Timer Period Timer Display Timer Position Presentation Timer Timer Counting Direction Sound Reminder Start Counting/Off High Altitude Mode On/Off DCR On/Off Audio Mode Standard/Speech/ - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 58
Description of each menu 1. DISPLAY menu Function Screen Color Aspect Ratio Keystone Corner Adj. Position Phase Description See "Using Screen Color" on page 32 for details. This function is only available when a PC input signal is selected. See "Selecting the aspect ratio" on page 30 for details. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 59
2. PICTURE menu Function Description Color See "Adjusting Color" on page 33 for details. Tint See "Adjusting Tint" on page 33 for details. The function is only available when Video or S-Video input with NTSC system is selected. Advanced Sharpness See "Adjusting Sharpness" on page 33 for details. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 60
3. SOURCE menu Function Description Auto Power Off Smart Restart Power Saving See "Setting Power Saving" on page 59 for details. Sleep Timer See "Setting Sleep Timer" on page 59 for details. Selecting Enable enables you to restart the projector immediately within 120 seconds after turning it off - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 61
4. SYSTEM SETTING: BASIC menu Function Splash Screen Screen Capture My Button Advanced High Altitude Mode DCR Description Allows you to select which logo screen will be displayed during projector start-up. See "Creating your own startup screen" on page 37 for details. Sets a hotkey on remote - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 62
Economic" on page 59 for details. Reset Lamp Hours Resets the lamp timer after new lamp is installed. For changing the lamp, please contact qualified service personnel. Lamp Hours See "Getting to know the lamp hour" on page 59 for details on how the total lamp hour is calculated. See "Using - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 63
6. INFORMATION menu Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. Color System Shows input system format. Current System Status Lamp Hours Displays the number of - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 64
detergents. These can damage the case. Storing the projector If you need to store the projector for an extended time, please follow the instructions below: • Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 65
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. As the arrows shown to the right, fit the filter by - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 66
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Lamp Settings menu. 2. Press - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 67
operate normally. Notice Replace Lamp Now Lamp > ____ Hours Lamp usage time exceeded OK Notice Out of Lamp Usage Time Replace lamp (refer to User Manual) Then reset lamp timer OK 60 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 68
Replacing the lamp Turn the power off and disconnect the projector from the power outlet. Please contact qualified service personnel for changing the lamp. Type number: • PJD6350/PJD6351Ls: RLC-092 • PJD6550Lw/PJD6551Lws: RLC-093 • PJD6352/PJD6352Ls: RLC-097 • PJD6552Lw/PJD6552Lws: RLC-098 61 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 69
Indicators Light Status & Description Power events Blue Flashing Off Blue Off Blue Off Blue Flashing Off Red Off Off Stand-by mode Off Powering up Off Normal operation Off Normal power-down cooling (3 sec) Off Downloading Lamp events Blue Flashing Off Off Off Blue Off Red First - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 70
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Attempting to turn the projector on again during the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 71
Specifications Projector specifications • All specifications are subject to change without notice. • Not all models can be purchased in your region. General Product name Optical DLP Projector Resolution PJD6350/PJD6351Ls/PJD6352/PJD6352Ls: 1024 x 768 XGA Display system Lamp PJD6550Lw/ - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 72
Output terminal RGB output Audio signal output Speaker D-Sub 15-pin (female) x 1 Audio jack x 1 10 watt x 1 Control terminal RS-232 serial control LAN USB serial control IR receiver 9 pin x 1 RJ45 x 1 Type mini B x 1 (Front) Environmental Requirements Operating temperature Operating relative - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 73
Dimensions 315.24 mm (W) x 97.7 mm (H) x 227.93 mm (D) (Excluding extrusions) 227.93 97.7 315.24 Ceiling mount installation Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 63.62 60.87 27.13 13.00 1.45 198.10 Unit: mm 66 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 74
Timing chart Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ UXGA WSXGA+ HD MAC 13" MAC 16" MAC 19" MAC 21" Analog RGB Resolution (dots) Aspect Ratio 640 x 480 4:3 800 x 600 4:3 1024 x 768 4:3 1152 x 864 4:3 1280 x 768 15:9 1280 x 800 16:10 1360 x 768 16:9 1280 x 960 4:3 1280 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 75
Signal VGA SVGA XGA WXGA Quad-VGA SXGA SXGA+ WXGA+ WSXGA+ HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV (480p) SDTV (576p) SDTV (480i) SDTV (576i) HDMI Resolution (dots) Aspect Ratio 640 x 480 4:3 800 x 600 4:3 1024 x 768 4:3 1280 x 768 15:9 1280 x 800 16:10 1360 x 768 16:9 1280 x 960 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 76
for Side-by-Side, Top-Bottom, and Frame Sequential formats. ** 120 Hz signals are supported for Frame Sequential format only. *** Video signal (SDTV 480i) is supported for Frame Sequential format only. In Frame packing format Signal 1080p 720p In Side by side format Signal 1080i In Top and - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 77
Signal HDTV (1080p) HDTV (1080i) HDTV (720p) SDTV (480p) SDTV (576p) SDTV (480i) SDTV (576i) Signal NTSC PAL PAL60 SECAM Component video Resolution (dots) Aspect Ratio 1920 x 1080 16:9 1920 x 1080 16:9 1280 x 720 16:9 720 x 480 4:3 / 16:9 720 x 576 4:3 / 16:9 720 x 480 4:3 / 16:9 720 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 78
or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic Corporation makes no representations or warranties, either - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 79
Appendix IR control table Key PgDn PgUp Blank Auto sync Up Down Left Right Color Mode Mute Enter Power ON Presentation Timer Exit D. ECO (Eco mode) Menu Mouse Mouse Left Mouse Right Source Pattern My button HDMI Volume+ VolumeMagnify + Magnify VGA1 VGA2 Format NEC NEC NEC NEC NEC NEC NEC NEC NEC - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 80
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin 1 3 5 7 9 Description NC TX GND RTSZ NC Baud Rate Data Length Parity Check Stop Bit Flow Control - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 81
Function Power Reset all settings Reset Color Settings Splash Screen Quick Power Off High Altitude Mode Lamp Mode Statu s Write Read Action Turn on Turn off Power status (on/off) Execute Execute Write Read Write Read Write Read Write Read Splash Screen Black Splash - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 82
Message Projector Position 3D Sync 3D Sync Invert Contrast Brightness Write Read Write Read Write Read Write Read Write Read Write Read Message Off Message On Message status Front Table Rear Table Rear Ceiling Front Ceiling projector position status OFF Auto Frame Sequential Frame Packing Top- - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 83
Aspect ratio Auto Adjust Horizontal position Vertical position Color temperature Aspect ratio Auto Aspect ratio 4:3 Aspect ratio 16:9 Write Aspect ratio 16:10 Aspect ratio Anamorphic Aspect ratio Wide Aspect ratio 2.35:1 Aspect ratio Panorama Read Aspect ratio Execute Write Horizontal - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 84
Blank Keystone- Vertical KeystoneHorizontal Color mode Primary Color Hue Write Read Write Read Write Read Write Read Write Read Write Read Blank on Blank off Blank status Decrease Increase Keystone status Decrease Increase Keystone status Brightest Movie Standard ViewMatch Dynamic Preset mode - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 85
Saturation Gain Freeze Source input Quick Auto Search Mute Volume Write Read Write Read Write Read Write Read Write Read Write Read Write Read Saturation decrease Saturation increase Saturation Gain decrease Gain increase Gain Freeze on Freeze off Freeze status Input source VGA Input source VGA2 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 86
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 87
HDMI Format HDMI Range CEC Error status Brilliant Color Write Read Write Read Write Read Read Write Read RGB YUV Auto HDMI Format status Enhanced Normal Auto HDMI Range status Off On CEC status Read error status Brilliant Color 0 Brilliant Color 1 Brilliant Color 2 Brilliant Color 3 Brilliant - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 88
Remote Control code Screen Color Over Scan Write Read Write Read Write Read code 1 code 2 code 3 code 4 code 5 code 6 code 7 code 8 Remote Control code status Screen color Off Blackboard Greenboard Whiteboard Screen Color status Overscan Off Overscan 1 Overscan 2 Overscan 3 Overscan 4 Overscan 5 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 89
Remote Key Write Menu Exit Up Down Left Right Source Enter Auto My Button 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E 0x02 0x14 0x00 0x04 0x00 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 90
New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 [email protected] Canada www.viewsonic.com T= 1-866-463-4775 [email protected] Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 91
acts of nature, improper maintenance, unauthorized product modification, or failure to follow instructions supplied with the product. b. Operation outside of product specifications. c. Operation defect. 3. Removal, installation, one way transportation, insurance, and set-up service charges. - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 92
ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial number. 2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 93
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product. b. Any damage of the service charges. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 94
39300 Acapulco, Guerrero Tel: 744-48-32627 Monterrey: Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico FOR USA SUPPORT: ViewSonic Corporation 14035 Pipeline Ave. Chino, CA 91710, USA Tel: 800-688 - ViewSonic PJD6352LS - 1024 x 768 Resolution 3 500 ANSI Lumens 0.61 Throw Ratio | - Page 95
PJD6350/PJD6351LS/PJD6352/
PJD6352LS/PJD6550LW/
PJD6551LWS/PJD6552LW/
PJD6552LWS
DLP Projector
User Guide
Model No.
VS15877/VS15878/VS15947/VS15948/VS15879/
VS15880/VS15949/VS15950
IMPORTANT:
Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service.
Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”