Home » Viking Manuals » Dishwashers » Viking PDDP242SS » Manual Viewer

Viking PDDP242SS Installation Instructions

Viking PDDP242SS Manual

View all Viking PDDP242SS manuals

Add to My Manuals
Save this manual to your list of manuals

Viking PDDP242SS manual content summary:

Viking PDDP242SS | Installation Instructions - Page 1
Installation Guide Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 or visit our web site in the US at www.vikingrange.com or in Canada at www.brigade.ca F21043A EN (101513) 1 & 3 Series Built-In Dishwashers
Viking PDDP242SS | Installation Instructions - Page 2
20 Installing a Custom Panel 22 Installer Checklist 28 Final Instructions 28 Self-Help Hints 28 Service & Registration 29 IMPORTANT- Please Read and Follow • Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and
Viking PDDP242SS | Installation Instructions - Page 3
has missing or broken parts. • Also follow the safety instructions of the use and care guide. • To reduce the risk of electric shock, fire, or suffocation! • Remove the dishwasher door when removing an old dishwasher from service or discarding it. Ensure that the appliance presents no danger to
Viking PDDP242SS | Installation Instructions - Page 4
IMPORTANT- Please Read and Follow • Inspect the Dishwasher: After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. NOTICE • Do not discard any bags or items that come with the original
Viking PDDP242SS | Installation Instructions - Page 5
General Information Materials Which May Be Needed Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8" N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the
Viking PDDP242SS | Installation Instructions - Page 6
(B) in order to fix from sides (if necessary). Adjusting Height If the height of the enclosure is 33-7/8" to 35-7/8" (86.1cm-91.1cm), adjust supports as shown in the figure. Supplied (4) 10
Viking PDDP242SS | Installation Instructions - Page 7
Enclosure Preparation • Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. • Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. NOTICE • Make sure the dishwasher is plumb and
Viking PDDP242SS | Installation Instructions - Page 8
connection plug before attaching the drain hose from the dishwasher. • Every disposal has a hookup for a dishwasher; consult your disposer manual for correct connection (Figure C). C 13 Installation Preparation Steam Protection Foil Steam will form inside the dishwasher during operation. At the
Viking PDDP242SS | Installation Instructions - Page 9
Installation Placement of Dishwasher into the Opening Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked, and all slack is taken out as shown in
Viking PDDP242SS | Installation Instructions - Page 10
Installation • After installing one clip for each side, push the dishwasher into the cabinet (Figure E). • Note that while pushing the dishwasher into the cabinet, water supply hose must move in the channel to the front (Figure F). • Fix the second clip (Figure G). Installation Water supply may
Viking PDDP242SS | Installation Instructions - Page 11
to reduce the likelihood of damage to the power-supply cord. Grounding Instructions This appliance must be grounded. In the event of a malfunction or a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly
Viking PDDP242SS | Installation Instructions - Page 12
Installation o A B t s C If the enclosure height is below 33-1/16" (84.0cm), use only (o) labeled kickplate (kickplate without slots). Installation should be done following the steps illustrated in the Figures A, B, and C respectively. 1. Bend tabs on kickplate (o) inwards (A). 2. Secure kickplate
Viking PDDP242SS | Installation Instructions - Page 13
Installation 3. Mark the wooden door as shown in the drawing (Figure C). Min: 12.1 lb (5.5 kg) Max: 15.4 lb (7.0 kg) 4. Place the plastic mounting brackets over the marked holes. Align the bottom of the bracket with the horizontal line. Align the middle of the bracket with the center line using
Viking PDDP242SS | Installation Instructions - Page 14
Installation x4 Ø 3/16" (4mm) y 8. Using the four screws Ø 3/16"x1-11/16" (Ø 4mmx43mm) provided, attach the wooden door to the dishwasher at position 1 and 4 (Figure A). A 9. Check the position of the wooden door and make sure it is aligned properly (Figure B). Ø 3/16" (4mm) x4 y B 10. Tighten
Viking PDDP242SS | Installation Instructions - Page 15
hardness for your area. If the dishwasher drain is connected to a garbage disposal, make sure that the drain/hopper plug has been removed. Final Instructions • Press the On/Off button to turn the dishwasher on. • Power indicator light comes on. • Use the Program Select button to choose a washing
Viking PDDP242SS | Installation Instructions - Page 16
the manual. All servicing should be referred to a qualified technician. Contact Viking Range, LLC, 1-888-845-4641, for the nearest service parts service is ever required. Model number Serial number Date of purchase Date installed Dealer's name Address These installation instructions