Vtech 3111-2 Quick Start Guide

Quick start guide

for model DS3111-2

NOTES:

1.

Use only the power adapters and batteries supplied with your VTech

telephone.

2.

For complete feature instructions, please refer to your user’s manual.

96-006499-030-100

issue 2

IMPORTANT!

If your product is not working properly:

Refer to the

Troubleshooting

section of the user’s manual.

Visit our website at www.vtechphones.com.

In Canada, go to www.vtechcanada.com.

Call our customer service at 1 (800) 595-9511.

In Canada, call 1 (800) 267-7377.

•

•

•

Telephone base installation

We recommend that you install the telephone base away from any electronic

equipment and appliances such as personal computers, computer routers,

television sets, microwave ovens or refrigerators. Avoid excessive heat,

cold, dust or moisture. When a location is selected, install the telephone

base and the charger as shown below. Make sure that the electrical outlet

is not controlled by a wall switch.

MANUFACTURED IN CHINA

COMPLIES WITH 47 CFR PART 68

REGISTRATION NO.: US:EW7W401B80-565600

RINGER EQUIVALENCE: 0.1B

USOC JACK: RJ11C/RJ11W

HAC

FCC ID: EW780-5656-00

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF

COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE.

DC 6V 300mA

CLASS 2 POWER SOURCE ONLY

TELEPHONE

EQUIPMENT

Telephone

wall jack

Electrical outlet

not controlled

by a wall switch

Power adapter

Charger adapter

Telephone

line cord

Handset battery installation

Install the handset battery by following these steps:

1. Align the two holes of the battery plug with the socket pins in the handset

battery compartment, matching the red and black wires to the color-

coded label.

2. Place the battery in the compartment with the wires in the lower right

corner.

3. Position the battery compartment cover and slide it towards the unit

until it clicks into place.

For optimal performance, we recommend that you charge the handset for

16 hours. You can keep the battery charged by returning the handset to the

telephone base after each use. When the battery power is fully depleted,

a full recharge takes about 16 hours.

IC:xxxxX-xxxxxxxx

IC:xxxxX-xxxxxxxx

IC:xxxxX-xxxxxxxx

IC:xxxxX-xxxxxxxx

Make, receive and end calls

Make a call

•

Press

/

FLASH

or

to ensure there is a dial tone, then dial the

telephone number.

-OR-

1. Dial the number (press

MUTE/REMOVE

to make corrections;

press and hold

REDIAL/PAUSE

to insert a dialing pause).

2. Press

/FLASH

or

to use the speakerphone.

Receive a call

• Press

/

FLASH

,

or any dialing keys (

0

-

9

,

*

or

#

) to answer an

incoming call.

End a call

• Press

OFF/CLEAR

or put the handset back in the telephone base

or charger.

Voicemail setup

This feature allows you to use the

VOICEMAIL

,

PLAY

,

SKIP

and

ERASE

buttons to access your voicemail (a subscription service available from

your local telephone company for a fee). Before completing these steps, be

sure to have your access number and password to access your voicemail

available. You will also need the key sequence to play, skip and delete your

messages. Contact your local telephone company for more information

about voicemail service.

To program the

ACCESS NUMBER

button:

1. Press

MENU/SELECT

from the idle mode.

2. Press

or

to select

VOICEMAIL SETUP

, then press

MENU/SELECT

.

3. Press

or

to select

ACCESS NUMBER

, then press

MENU/SELECT

.

4. Use the dial pad to enter the access number. Press

MUTE/REMOVE

to delete characters if necessary.

5. Press

MENU/SELECT

. You’ll hear a conﬁrmation tone.

To program the

PASSWORD

,

PLAY

,

SKIP

and

ERASE

buttons, follow

the above steps.

To program a pause:

1. Press

MENU/SELECT

from the idle mode.

2. Press

or

to select

VOICEMAIL SETUP

then press

MENU/SELECT

twice.

3. The blinking cursor should be at the end of your access number. Press

and hold the

REDIAL/PAUSE

button until a

P

appears.

4. Press

MENU/SELECT


To reset all codes:

1. Press

MENU/SELECT

from the idle mode.

2. Press

or

to select

VOICEMAIL SETUP

then press

MENU/SELECT

.

3. Press

or

to select

RESET ALL CODES

, then press

MENU/SELECT

.

4. The screen displays

RESET CODES?

5. Press

MENU/SELECT


NOTE:

You must program your voicemail buttons before you can access all of

the functions available with your voicemail.

QSG DS3111-2 071207.indd

1

7/28/2007

5:54:04 PM

Vtech 3111-2 Quick Start Guide

Vtech 3111-2 Manual

Vtech 3111-2 manual content summary: