Vtech CS6429-2 User Manual (CS6429-2 User Manual) - Page 8

Battery charging, LOW BATTERY, Set date and time, CANCEL - battery for

Get Vtech CS6429-2 PDF manuals and user guides
UPC - 735078019998
View all Vtech CS6429-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Getting started Battery charging Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 10 hours of continuous charging. See the table on page 50 for battery operating times. If the screen is blank, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. When the battery is low, the handset plays four short beeps and shows LOW BATTERY along with a flashing icon. When you are on a call in low battery mode, the handset plays four short beeps every 50 seconds. The following table summarizes the battery charge indicators and actions to take. Battery indicators The screen is blank, or shows PLACE IN CHARGER and flashes. The screen shows LOW BATTERY and flashes. The screen shows HANDSET X. Battery status Battery has no charge or very little charge. The handset cannot be used. Action Charge without interruption (at least 30 minutes). Battery has enough charge to be used for a short time. Battery is charged. Charge without interruption (at least 30 minutes). To keep the battery charged, place it in the telephone base or charger when not in use. If you place the handset in the telephone base or charger without plugging in a battery, the screen displays NO BATTERY. After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time. For instructions, see Set date and time on page 14. To skip setting the date and time, press OFF/CANCEL. SET DATE --/--/-- 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
4
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). If necessary, place the handset in the telephone base or charger
to charge the battery. For best performance, keep the handset in the telephone
base or charger when not in use. The battery is fully charged after 10 hours of
continuous charging. See the table on page 50 for battery operating times.
If the screen is blank, you need to charge the handset without interruption for
at least 30 minutes to give the handset enough charge to use the telephone for
a short time. When the battery is low, the handset plays four short beeps and
shows
LOW BATTERY
along with a flashing
icon. When you are on a call in
low battery mode, the handset plays four short beeps every 50 seconds.
The following table summarizes the battery charge indicators and actions to take.
Battery indicators
Battery status
Action
The screen is blank,
or shows
PLACE IN
CHARGER
and
flashes.
Battery has no charge
or very little charge. The
handset cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows
LOW BATTERY
and
flashes.
Battery has enough
charge to be used for a
short time.
Charge without interruption (at
least 30 minutes).
The screen shows
HANDSET X
.
Battery is charged.
To keep the battery charged,
place it in the telephone base
or charger when not in use.
Getting started
If you place the handset in the telephone base or charger without plugging in a
battery, the screen displays
NO BATTERY
.
After you install your telephone or power returns following a power outage, the
handset will prompt you to set the date and time. For instructions, see
Set date and time
on page 14. To skip setting the date and
time, press
OFF
/CANCEL
.
SET DATE
--/--/--