Vtech Four Handset Expandable Cordless Phone System with BLUETOOTH® Wireless Te

Vtech Four Handset Expandable Cordless Phone System with BLUETOOTH® Wireless Technology Manual

Get Vtech Four Handset Expandable Cordless Phone System with BLUETOOTH® Wireless Technology PDF manuals and user guides View all Vtech Four Handset Expandable Cordless Phone System with BLUETOOTH® Wireless Technology manuals
Add to My Manuals
Save this manual to your list of manuals

Vtech Four Handset Expandable Cordless Phone System with BLUETOOTH® Wireless Technology manual content summary:

  • 1
Duo
DECT
Cordless
Phone
with
Bluetooth
BLUETOOTH
SETUP
Bluetooth
setup
To
use
a
Bluetooth
enabled
mobile
phone
with
your
DDA200BT,
you
must
first
pair
and
connect
your
Bluetooth
device(s)
with
the
DDA200BT.
All
DDA200BT
handsets
can
be
used
to
make
or
answer
calls
on
the
mobile
phone
line.
Bluetooth
wireless
technology
operates
within
a
short
range.
When
you
pair
a
Bluetooth
mobile
phone
or
Bluetooth
headset
to
the
DDA200BT,
place
the
mobile
phone
next
to
the
DDA200BT
base
to
maintain
sufficient
signal
strength.
Pair
a
mobile
phone
Before
you
begin,
make
sure
that
you
have
mobile
coverage
and
your
Bluetooth
enabled
mobile
phone
is
not
connected
to
any
other
Bluetooth
device
To
pair
and
connect
a
mobile
phone
1.
In standby
mode,
press
MENU/SELECT
then
UP/DOWN
to
select
Bluetooth
(Figure
1)
2.
Press
MENU/SELECT
then
UP/DOWN
to
select
Add
cellular
(Figure
2)
3.
Press
MENU/SELECT.
The
display
shows
ADD
CELLULAR
Place
mobile
phone
next
to
base.
Press
OK
(Figure
3)
•
If
there
are
already
four
devices
on
the
paired
devices
list,
the
display
shows
Maximum
of
4
devices
can
be
paired
and
prompts
you
to
replace
an
existing
paired
device.
4.
Press
MENU/SELECT.
The
screen
displays
Please
set
your
mobile
phone
to
search
for
devices,
then
press
OK.
(Figure
4)
•
If
a
device
is
already
connected
to
the
DDA200BT,
the
screen
displays
Connected
device
will
be
temporarily
disconnected.
Press
OK.
Press
MENU/SELECT
to
temporarily
disconnect
the
device
and
continue
the
pairing
process.
5.
Press
MENU/SELECT
to
set
the
DDA200BT
to
discoverable
mode.
Then,
promptly
turn
on
the
Bluetooth
feature
of
your
mobile
phone,
make
sure
the
mobile
is
visible
to
other
Bluetooth
devices,
and
search
for
or
add
new
devices.
6.
Once
your
mobile
phone
finds
DDA200BT,
press
the
appropriate
key
on
your
mobile
phone
to
continue
the
pairing
process.
7.
Enter
the
PIN
of
the
DDA200BT
(the
default
PIN
is
0000)
into
your
mobile
phone
to
continue
the
pairing
process
(Figure
5)
8.
When
a
device
is
successfully
connected,
the
handset
displays
Paired
with
mobile
and
then
Mobile
setup
completed
Device
connected
(Figure
6).
The
corresponding
status
icon
(Mobilel
or
Mobile
2)
displays.
The
corresponding
device
light
on
the
DDA200BT
base
(DEVICE1
or
DEVICE2)
turns
on.
•
When
you
already
have
two
devices
on
the
active
devices
list,
the
handset
shows
Maximum
of
2
devices
can
be
connected.
You
are
prompted
to
replace
an
existing
device
on
the
active
devices
list.
Notes
•
The
pairing
process
may
take
up
to
one
minute.
If
the
pairing
process
fails,
try
again.
•
The
steps
for
the
pairing
process
may
vary
for
different
mobile
phones.
If
this
happens,
follow
the
prompts
on
your
mobile
phone
and
your
DDA200BT
to
complete
the
pairing
process.
•
If
you
put
the
handset
back
in
the
DDA200BT
base
or
charger
while
pairing,
the
process
terminates
and
the
handset
returns
to
idle
mode.
A
V
Figure
1
Figure
3
Figure
5
Products
Supplied
by
Sizwe
Broadband
www.sizwebroadband.co.za
A
V
Figure
2
A
V
Figure
4
izwe
BROADBAND
Figure
6
J
Global
No.1
Cordless
Phone
Manufacturer
J
1111
1111
III
I
1111
11
111111
II
1111
III
1
II
I
1111
1