Weber Summit S-470 LP Owner Manual - Page 32

Sideburner Maintenance, Rotisserie Troubleshooting

Get Weber Summit S-470 LP PDF manuals and user guides View all Weber Summit S-470 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

32 SIDEBURNER MAINTENANCE SIDE BURNER MAINTENANCE ƽ WARNING: All gas controls and supply valves should be in the "OFF" position. Make sure black wire is connected between the igniter and electrode. Make sure white wire is connected between the igniter and grounding clip. Spark should be a white/blue color, not yellow. 1) Igniter Wire 2) Ground wire 3) Burner Side Burner Grate Side Burner cap Side Burner Ring & Head Igniter Electrode Control Knob Igniter ROTISSERIE TROUBLESHOOTING PROBLEM CHECK CURE Rotisserie burner does not light. Did you hold the burner control knob in and hold in for 20 seconds until after burner ignited? Did you wait to see the entire ceramic surface become alight before counting 20 seconds? Did you repeatedly use the snap ignition until the burner ignited? Does the igniter work (Do you see a spark when you repeatedly use the snap igniter? Try to relight burner by holding burner control knob in and continue holding in until 20 seconds after burner has ignited. When relighting burner by holding burner control knob in, wait to see the entire ceramic surface become alight before counting 20 seconds? After waiting five minutes for gas to clear, try repeatedly using the snap igniter until the burner ignites (refer to "Lighting the Rotisserie Burner"). Try manually lighting the burner (refer to "Lighting the Rotisserie Burner"). Call customer service. General Symptoms: Burner does not light. -or- Burner has a small flickering flame The excess flow safety device, which is part of the barbecue to cylinder connection, may have activated. To reset the excess flow safety device turn all burner control knobs and the cylinder valve to "OFF". Disconnect the regulator from the cylinder. Turn burner control knobs to "START/HI". Wait at least 1 minute. Turn burner control knobs to "OFF". Reconnect the regulator to the cylinder. Turn cylinder valve on slowly. Refer to "Lighting Instructions". If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®. WWW.WEBER.COM®

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
32
WWW.WEBER.COM
®
SIDEBURNER MAINTENANCE
Side Burner Grate
Side Burner cap
Side Burner Ring & Head
Igniter Electrode
Control Knob
Igniter
SIDE BURNER MAINTENANCE
±
WARNING: All gas controls and supply valves should be in
the “OFF” position.
Make sure black wire is connected between the igniter and electrode.
Make sure white wire is connected between the igniter and grounding clip.
Spark should be a white/blue color, not yellow.
1)
Igniter Wire
2)
Ground wire
3)
Burner
PROBLEM
CHECK
CURE
Rotisserie burner does not light.
Did you hold the burner control knob in and
hold in for 20 seconds until after burner
ignited?
Try to relight burner by holding burner control knob in and continue holding in until
20 seconds after burner has ignited.
Did you wait to see the entire ceramic surface
become alight before counting 20 seconds?
When relighting burner by holding burner control knob in, wait to see the entire
ceramic surface become alight before counting 20 seconds?
Did you repeatedly use the snap ignition until
the burner ignited?
After waiting five minutes for gas to clear, try repeatedly using the snap igniter until
the burner ignites (refer to “Lighting the Rotisserie Burner”).
Does the igniter work (Do you see a spark
when you repeatedly use the snap igniter?
Try manually lighting the burner (refer to “Lighting the Rotisserie Burner”). Call
customer service.
General Symptoms:
Burner does not light. -or- Burner has
a small flickering flame
The excess flow safety device, which is part of
the barbecue to cylinder connection, may have
activated.
To reset the excess flow safety device turn all burner control knobs and the cylinder
valve to “OFF”. Disconnect the regulator from the cylinder. Turn burner control
knobs to “START/HI”. Wait at least 1 minute. Turn burner control knobs to “OFF”.
Reconnect the regulator to the cylinder. Turn cylinder valve on slowly. Refer to
“Lighting Instructions”.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
®
.
ROTISSERIE TROUBLESHOOTING