Weber Summit S-470 LP Owner Manual - Page 33

Sear Burner Troubleshooting, Handle Light Troubleshooting

Get Weber Summit S-470 LP PDF manuals and user guides View all Weber Summit S-470 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

PROBLEM Burners burn with a yellow or orange flame, in conjunction with the smell of gas (This is normal for the burner lighting tube). Sear Station burner does not light. SEAR BURNER TROUBLESHOOTING 33 CHECK Inspect Spider/Insect Screens for possible 33 CURE Clean Spider/Insect Screens. (See Section "Annual Maintenance") obstructions. (Blockage of holes.) Did you ignite the two adjacent main burners (See Sear Station™ burner lighting instructions for safe lighting procedure) Does Burner light with a match? Does the igniter work (Do you see a spark when you repeatedly use the snap igniter? Verify adjacent main burner ignition by visual inspection of a flame. ƽ WARNING: If ignition does not occur in 5 seconds, turn burner control OFF, wait 5 minutes to let the gas clear before you try again If you can light Burner with a match, then check the Crossover® Channel on the sear burner. (See Maintenance for burner removal and cleaning procedure.) Try manually lighting the burner (refer to "Lighting the Rotisserie Burner"). Call customer service. General Symptoms: Burner does not light. -or- Burner has a small flickering flame The excess flow safety device, which is part of the barbecue to cylinder connection, may have activated. To reset the excess flow safety device turn all burner control knobs and the cylinder valve to "OFF". Disconnect the regulator from the cylinder. Turn burner control knobs to "START/HI". Wait at least 1 minute. Turn burner control knobs to "OFF". Reconnect the regulator to the cylinder. Turn cylinder valve on slowly. Refer to "Lighting Instructions". If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®. OPERATING THE HANDLE LIGHT The Weber Grill Out™ Handle Light has a built-in "Tilt Sensor." With the power button (a) activated, the light will come on when the grill lid is open. The light will turn off when the lid is closed. For daytime use, deactivate the sensor by pressing power button (a). HANDLE LIGHT TROUBLESHOOTING PROBLEM CHECK CURE Weber Grill Out™ Handle Light does not light. Are the batteries old? Are the batteries installed correctly? Is the lid in the up position with the power button ON? Replace batteries. See assembly illustration. Light will activate when lid is open. Is the Weber Grill Out™ Handle Light activated? Press the power button. Is the Weber Grill Out™ Handle Light positioned correctly on the handle? Adjust position (See assembly illustration). If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®. ƽ ATTENTION: This product has been safety tested and is only certified for use in a specific country. Refer to country designation located on outer carton. These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products Co., Customer Service Department for genuine WeberStephen Products Co. replacement part(s) information. ƽ WARNING: Do not attempt to make any repair to gas carrying or gas burning components without contacting Weber-Stephen Products Co., Customer Service Department. Your actions, if you fail to follow this product Warning, may cause a fire or an explosion resulting in serious personal injury or death and damage to property. WWW.WEBER.COM®

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
33
WWW.WEBER.COM
®
33
SEAR BURNER TROUBLESHOOTING
OPERATING THE HANDLE LIGHT
The Weber Grill Out™ Handle Light has a built-in “Tilt Sensor.” With the power button
(a)
activated, the light will come on when the grill lid is open. The light will turn off when the lid
is closed. For daytime use, deactivate the sensor by pressing power button
(a)
.
HANDLE LIGHT TROUBLESHOOTING
PROBLEM
CHECK
CURE
Weber Grill Out
™
Handle
Light does not light.
Are the batteries old?
Replace batteries.
Are the batteries installed correctly?
See assembly illustration.
Is the lid in the up position with the power button ON?
Light will activate when lid is open.
Is the Weber Grill Out
™
Handle Light activated?
Press the power button.
Is the Weber Grill Out
™
Handle Light positioned correctly on the handle?
Adjust position (See assembly illustration).
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com
®
.
PROBLEM
CHECK
CURE
Burners burn with a yellow or orange
flame, in conjunction with the smell
of gas (This is normal for the burner
lighting tube).
Inspect Spider/Insect Screens for possible
obstructions. (Blockage of holes.)
Clean Spider/Insect Screens. (See Section “Annual Maintenance”)
Sear Station burner does not light.
Did you ignite the two adjacent main burners
(See Sear Station
™
burner lighting instructions
for safe lighting procedure)
Verify adjacent main burner ignition by visual inspection of a flame.
±
WARNING: If ignition does not occur in 5 seconds, turn burner control
OFF, wait 5 minutes to let the gas clear before you try again
Does Burner light with a match?
If you can light Burner with a match, then check the Crossover
®
Channel on the sear
burner. (
See Maintenance for burner removal and cleaning procedure.)
Does the igniter work (Do you see a spark
when you repeatedly use the snap igniter?
Try manually lighting the burner (refer to “Lighting the Rotisserie Burner”). Call
customer service.
General Symptoms:
Burner does not light. -or- Burner has
a small flickering flame
The excess flow safety device, which is part of
the barbecue to cylinder connection, may have
activated.
To reset the excess flow safety device turn all burner control knobs and the cylinder
valve to “OFF”
. Disconnect the regulator from the cylinder. Turn burner control knobs
to “START/HI”
. Wait at least 1 minute. Turn burner control knobs to “OFF”
. Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly. Refer to “Lighting
Instructions”
.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com
®
.
±
ATTENTION: This product has been safety tested and is only certified for use in a specific country. Refer to country
designation located on outer carton.
These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products Co., Customer Service Department for genuine Weber-
Stephen Products Co. replacement part(s) information.
±
WARNING: Do not attempt to make any repair to gas carrying or gas burning components without contacting Weber-Stephen
Products Co., Customer Service Department. Your actions, if you fail to follow this product Warning, may cause a fire or an
explosion resulting in serious personal injury or death and damage to property.