Home » Weed Eater Manuals » Lawn & Garden » Weed Eater WE EL-15TNE » Manual Viewer

Weed Eater WE EL-15TNE Owner Manual

Weed Eater WE EL-15TNE Manual

View all Weed Eater WE EL-15TNE manuals

Add to My Manuals
Save this manual to your list of manuals

Weed Eater WE EL-15TNE manual content summary:

Weed Eater WE EL-15TNE | Owner Manual - Page 1
produit en ligne à l'adresse : www.weedeater.com Instruction Manual Manual de Instrucciones 245157 Manuel d'Instructions WE EL-15TNE WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Read instructions carefully before assembling. Failure to do so
Weed Eater WE EL-15TNE | Owner Manual - Page 2
instructions in this manual and on the unit. Read entire instruction manual Trimmer line throws ob- jects violently. You and others can be blinded/ injured. Wear safety glasses, boots, and leg protection. Keep body parts clear of rotating line extension cord before use and replace if damaged. Do not
Weed Eater WE EL-15TNE | Owner Manual - Page 3
recommended trimmer line (see USER REPLACEABLE SERVICE PARTS in the SERVICE AND ADJUSTMENTS section). Never use wire, rope, string, etc. • Use specified trimmer spool. Make sure spool is properly installed and all parts are securely fastened. • Use only WEED EATER replacement parts and accessories
Weed Eater WE EL-15TNE | Owner Manual - Page 4
proper length while running. The line limiter blade (on underside of shield) is sharp and can cut you. NOTE: If shield is not properly installed, damage to unit (including motor failure) will result. 1. Insert edge guide into two holes in shield. NOTE: Edge guide must be positioned on shield prior
Weed Eater WE EL-15TNE | Owner Manual - Page 5
and adjustments. Save this manual for future reference. Trigger Switch Assist Handle Twist and Edge Button Motor Housing Cord Retainer Clamp Recessed Plug Locking Sleeve Assembly Air Vents Debris Shield Edge Guide Trimmer Head with 0.065 inch Trimmer Line RECESSED PLUG The RECESSED
Weed Eater WE EL-15TNE | Owner Manual - Page 6
position. 1. Push the Twist 'N Edge Button. 2. Adjust the trimmer to the desired height by moving the motor housing up or down the tube (four height positions available). 3. Release the button. The tube will lock in position. AUTOMATIC LINE FEED SYSTEM When the trimmer is initially started, a small
Weed Eater WE EL-15TNE | Owner Manual - Page 7
pressing the head into the ground as this can scalp the ground and damage the tool. Mowing EDGING POSITION While holding the trimmer in operating position, you can press this button and twist the lower portion 180° counterclockwise for edging. Button EDGING While edging allow the tip of the line to
Weed Eater WE EL-15TNE | Owner Manual - Page 8
-- 12 cm) unwound. Notches Hub Eyelet 4. Remove old spool. 5. Clean entire surface of hub and spool. 6. Replace with a pre--wound spool or cut a length of 26 feet (8 meters) of 0.065″ (1.65 mm) diameter WEED EATER brand line. Use of heavier lines could overload and damage unit. WARNING: Never use
Weed Eater WE EL-15TNE | Owner Manual - Page 9
USER REPLACEABLE SERVICE PARTS REPLACEMENT PART Spool with 0.065 inch Trimmer Line Assist Handle Bolt Carriage, M6 X 1 Knob Clamp Shield Assembly Edge Guide Spool cap Bolt PART NUMBER 952711920 574495601 574495901 574473101 574495801 574495401 574491601 574492201 574471601 STORAGE WARNING:
Weed Eater WE EL-15TNE | Owner Manual - Page 10
recommended by WEED EATER for this product. Additionally, this warranty does not cover parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover predelivery set-up or normal adjustments explained in the instruction manual. Should you