Weider 20ct English Manual
Weider 20ct Manual
 |
View all Weider 20ct manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 20ct manual content summary:
- Weider 20ct | English Manual - Page 1
CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Patent Pending Visit our website at www.weiderfitness.com new products, prizes, fitness tips - Weider 20ct | English Manual - Page 2
ADJUSTMENTS 17 WEIGHT RESISTANCE CHART 19 TROUBLE-SHOOTING AND MAINTENANCE 20 CABLE DIAGRAM 21 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual - Weider 20ct | English Manual - Page 3
this manual. 2. It is the responsibility of the owner to ensure that all users of this weight system are adequately informed of all warnings and precautions. 3. The weight system is intended for home use only. Do not use the weight system in any commercial, rental, or institutional setting. 4. Use - Weider 20ct | English Manual - Page 4
and strength, or improve your cardiovascular system, the WEIDER® 20CT will help you to achieve the specific results you want. For your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Department toll-free at 1-800 - Weider 20ct | English Manual - Page 5
parts bag for that stage. Place all parts of the weight system in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after - Weider 20ct | English Manual - Page 6
FRAME ASSEMBLY 1. Before beginning assembly, be sure that you have read and understand the information in the box above. Press two 2" Outer Caps (51) onto the indicated locations on the Stabilizer (5). Press two 2" Inner Caps (27) into the indicated ends of the Stabilizer and the Base (4). Insert - Weider 20ct | English Manual - Page 7
(refer to step 4). Lubricate the inside of the holes in a Top Weight (65). Set the Top Weight onto the front stack of Weights (25). Insert both Long Weight Guides (62) into the stack of Weights. Be sure that the holes in the Weight Guides are at the top, as shown. 3 27 11 74 11 55 3 8 96 44 - Weider 20ct | English Manual - Page 8
to step 4). Lubricate the inside of the holes in the other Top Weight (65). Set the Top Weight onto the rear stack of Weights (25). Insert both Short Weight Guides (73) into the stack of Weights. Be sure that the holes in the Weight Guides are at the top, as shown. 6 Lubricate 65 Pin 63 64 Holes - Weider 20ct | English Manual - Page 9
9. Wet the handle of one Press Arm (46) with soapy 9 water. Slide a 5" Plastic Grip (83) onto the han- dle. Press a 1" Round Inner Cap (49) into the other end of the handle. Press a 1 3/4" Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two - Weider 20ct | English Manual - Page 10
8 3 Bracket 49 87 91 82 85 84 CABLE ASSEMBLY 13 During steps 13 to 25, refer to the CABLE DIAGRAM on page 21 of this manual. Identify the three cables by their lengths, and note the positions of the cable traps. IMPORTANT: Do not overtighten the bolts and nuts securing the - Weider 20ct | English Manual - Page 11
15. Route the Medium Cable (58) around the "V"Pulley (50) on the Right Arm (48). Be sure that the Cable is in the groove of the Pulley and that the Long Cable Trap (31) is positioned to hold the Cable in place. Tighten the 3/8" x 2 1/2" Bolt (86) and the 3/8" Nylon Locknut (not shown). Route the - Weider 20ct | English Manual - Page 12
threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing. Attach the Small "U"-Bracket (71) to the indicated Weight Tube (63) with a 5/16" x 1 3/4" Bolt (24) and a 5/16" Nylon Locknut (3). 58 71 24 3 63 58 10 71 2 2 12 - Weider 20ct | English Manual - Page 13
threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing. Attach the Small "U"-Bracket (71) to the indicated Weight Tube (63) with a 5/16" x 1 3/4" Bolt (24) and a 5/16" Nylon Locknut (3). 3 63 58 71 2 72 71 24 10 2 23. Route the Long Cable (72) around the - Weider 20ct | English Manual - Page 14
24. Wrap the Long Cable (72) around a 3 1/2" Pulley (15). Attach the Pulley and a Cable Trap (66) to the Squat Arm (84) with the 3/8" x 2 1/4" Bolt (94) and a 3/8" Jamnut (92). Be sure that the Jamnut is on the side shown and that the Cable Trap is positioned to hold the Cable in place. 24 94 66 - Weider 20ct | English Manual - Page 15
a 1/4" Washer (10) onto the Carriage Bolt. Attach the other end of the Seat (13) to the Seat Frame (36) with a 1/4" Washer (10) and a 1/4" x 2" Machine Screw (81). 28. Press a 1 1/2" Inner Cap (32) into the Leg Lever 28 (29). Lubricate the 5/16" x 2 1/4" Bolt (33). Attach the Leg Lever (29) to - Weider 20ct | English Manual - Page 16
the Right VKR Arm (80) with two 1/4" x 2" Machine Screws (81) and two 1/4" Washers (10). Attach a manual. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem - Weider 20ct | English Manual - Page 17
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments - Weider 20ct | English Manual - Page 18
THE SEAT To attach the Seat (13), set the bracket on the Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16" x 2 3/4" Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed - Weider 20ct | English Manual - Page 19
resistance at each station. "Top" refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEY SQUAT ARM PLATES (lbs.) (lbs - Weider 20ct | English Manual - Page 20
TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system on the weight system, can stretch the weight pin into the middle of the weight stack. weight will 21 be lifted off the weight - Weider 20ct | English Manual - Page 21
the diagram to be sure that the three cables and cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may occur. The insets show the proper positioning of the cable traps; the cable traps should be positioned - Weider 20ct | English Manual - Page 22
PART IDENTIFICATION CHART-Model No. WESY85311 R0802A 3/8" Washer (9) 5/16" Washer (8) 1/4" Washer (10) 3/8" Nylon Locknut (21) 1/4" x 2" Machine Screw (81) 3/8" Jamnut (92) 5/16" x 1 3/4" Bolt (24) 5/16" Nylon Locknut (3) 1/4" Nylon Locknut (2) 1/4" x 3/4" Screw (18) Cable Clip (53) 1" x - Weider 20ct | English Manual - Page 23
3/8" x 2 1/2" Bolt (86) 3/8" x 2 1/4" Bolt (94) 5/16" x 2 1/4" Bolt (33) 1/4" x 2 1/2" Screw (43) 1/4" x 2" Carriage Bolt (38) 3/8" x 2" Bolt (12) 5/16" x 2 1/2" Bolt (22) 5/16" x 2 1/2" Carriage Bolt (1) 5/16" x 2 3/4" Bolt (11) 5/16" x 2 3/4" Carriage Bolt (14) 5/16" x 3" Bolt (75) 3/8" x 3 1/2" - Weider 20ct | English Manual - Page 24
Round Inner Cap (96) 1/2" x 17/32" Spacer (91) 1" Round Inner Cap (49) 5/8" x 3/8" Spacer (76) 1/2" x 3/4" Spacer (61) 3/4" Round Inner Cap (34) 5/8" x 9/16" Spacer (7) 1" Round Cover Cap (70) 1" Inner Cap (6) 1 1/2" Inner Cap (32) 1" x 2" Inner Cap (87) 1 3/4" Inner Cap (44) 2" Inner Cap - Weider 20ct | English Manual - Page 25
Short Weight Guide VKR Upright 5/16" x 3" Bolt 5/8" x 3/8" Spacer VKR Backrest VKR Armrest Left VKR Arm Right VKR Arm 1/4" x 2" Machine Screw Handle x 2 1/4" Bolt 3 1/2" Low Pulley Round Inner Cap User's Manual Exercise Guide Note: "#" indicates a non-illustrated part. Specifications are subject - Weider 20ct | English Manual - Page 26
78 83 27 75 80 32 10 81 49 77 75 83 32 3 61 3 73 60 27 3 11 3 11 10 43 2 10 3 79 67 72 71 24 31 50 76 65 63 3 78 25 74 64 12 66 15 26 51 19 11 8 11 5 8 21 1 56 9 21 21 27 51 1 83 83 54 52 39 53 86 68 12 27 55 20 21 3 12 66 15 21 15 21 61 60 22 83 87 8 - Weider 20ct | English Manual - Page 27
product (WEIDER® 20CT weight system) 3. The SERIAL NUMBER of the product (see the front cover of this manual) 4. repairs not provided by an ICON authorized service center, products used for commercial or rental in its scope and duration to the terms set forth herein. Some states do not allow
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
 |
 |
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee you complete
satisfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY85311
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (Under Seat)
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Patent Pending