Weider 8630 Canadian English Manual
Weider 8630 Manual
 |
View all Weider 8630 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 8630 manual content summary:
- Weider 8630 | Canadian English Manual - Page 1
SERVICE DEPARTMENT DIRECTLY. CALL TOLL-FREE: 1-888-936-4266 Mon.-Fri., 8:00 until 17:00 EST (excluding holidays) OR E-MAIL US: [email protected] CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL - Weider 8630 | Canadian English Manual - Page 2
BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the - Weider 8630 | Canadian English Manual - Page 3
plate when performing an exercise that could cause the weight system to tip. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using - Weider 8630 | Canadian English Manual - Page 4
on a decal attached to the weight system (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. High Pulley Station Lat Bar Ab Pulley Station Backrests Decal Assembled Dimensions: Height: 78 in./198 - Weider 8630 | Canadian English Manual - Page 5
for the Weight System How to Identify Parts To help you identify the small parts used in assembly, we have included a PART IDENTIFICATION CHART in the center of this manual. Place the chart on the floor and use it to easily identify parts during each assembly step. Note: Some small parts may have - Weider 8630 | Canadian English Manual - Page 6
on page 5. Refer to the PART IDENTIFICATION CHART in the center of this manual for help identifying small parts. 1 55 20 14 Locate and open the parts bags labeled 49 "FRAME ASSEMBLY." Insert six M8 x 63mm Carriage Bolts (49) up through the Press Base (13) and the Weight Base 2 (14). Attach the - Weider 8630 | Canadian English Manual - Page 7
M8 Nylon Locknuts (40). Do not tighten the Locknuts yet. 4 55 20 40 8 4 40 13 49 5. Insert two Weight Guides (23) into one of the 5 brackets on the Weight Base (14). Make sure the Weight Guides are oriented with the tall holes near the top (see the inset drawing). Attach the lower ends of - Weider 8630 | Canadian English Manual - Page 8
20 3 M8 Washers (20), and two M8 Nylon Locknuts 2 (40). Do not tighten the Locknuts yet. 10. Attach the upper ends of one set of Weight Guides (23) to the Top Frame (2) with an M8 x 152mm Bolt (67), two 13mm x 19mm Spacers (69), and an M8 Nylon Locknut (40). Attach the upper - Weider 8630 | Canadian English Manual - Page 9
11. Locate and open the parts bag labeled "ARM ASSEMBLY." Attach the Leg Press Plate (11) to the Adjustment Tube (10) with an M8 x 60mm Bolt (62), two M8 Washers (20), and an M8 Nylon Locknut (40). Make sure that the Leg Press Plate and Adjustment Tube are oriented as shown. 10 20 40 - Weider 8630 | Canadian English Manual - Page 10
Fly Arm is behind the indicated bracket on the Butterfly Frame (3). IMPORTANT NOTE: Before assembling the 25mm Retainers (45) used in this step, make sure that you thoroughly understand the step. The Retainers can be assembled only once. If they must be removed, you will need to order new Retainers - Weider 8630 | Canadian English Manual - Page 11
with the Right Fly Arm (5). 6 5 CABLE ASSEMBLY 18 18. Locate and open the parts bags labeled "CABLE ASSEMBLY," "CABLES," and "PULLEYS." During steps 19 through 49, refer to the CABLE DIAGRAMS on pages 26 and 27 of this manual to verify proper cable routing. Before beginning this section, fully - Weider 8630 | Canadian English Manual - Page 12
Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). Make sure that the Cable Trap is positioned to hold the Cable in place. 22. Wrap the Butterfly Cable Fly Arm (6) is shown removed for easier part identification. 23 Attach the Butterfly Cable (89) to the Left Fly Arm (6) - Weider 8630 | Canadian English Manual - Page 13
an M10 Nylon Locknut (42). The Cable must be routed from the direction shown. 2 42 40 50 82 87 27. Attach the Rear Cable (87) to a Small "U"-bracket the Cable so that two threads show past 68 the Locknut (see the inset drawing). Attach the Small "U"-bracket (32) to the indicated Weight Tube - Weider 8630 | Canadian English Manual - Page 14
an M8 Nylon Locknut (40) and an M8 Washer (20). Do not completely tighten the Locknut. It should be threaded onto the end of the Cable so that two threads are showing above the Locknut, as shown in the inset drawing. 40 20 84 40 20 88 88 84 29. Wrap - Weider 8630 | Canadian English Manual - Page 15
hole in the Pulley Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). The Cable must be routed from the direction shown. Make sure that the Cable Trap is positioned to hold the Cable in place. 31 31 42 50 80 82 88 32. Route the Press Cable (88) under a 90mm Pulley - Weider 8630 | Canadian English Manual - Page 16
. Route the Press Cable (88) over a 90mm Pulley 35 (82). Attach the Pulley and a Cable Trap (80) to the indicated hole in the Press Frame (12) with an M10 x 82mm Bolt (66), an M10 Washer (38), and an M10 Nylon Locknut (42). 66 88 38 12 82 42 80 36. Wrap the Press Cable - Weider 8630 | Canadian English Manual - Page 17
90mm Pulley (82) used in this step 39 was attached in step 38. It is shown removed for easier part identification. Route the Press Cable (88) around the 90mm Pulley (82). Make sure that the Cable Trap (80) is turned to hold the Cable in place and that the Cable is routed as shown. Tighten the - Weider 8630 | Canadian English Manual - Page 18
. Route the High Cable (85) under a 90mm Pulley (82). Attach the Pulley and a Cable Trap (80) to the single hole end of the Pulley Plates (31) with an M10 x 48mm Bolt (50) and the M10 Nylon Locknut (42). Make sure that the Cable Trap is positioned to hold the Cable in place. 44. Wrap the High Cable - Weider 8630 | Canadian English Manual - Page 19
(80) to 48 the lowest hole in the set of Pulley Plates (31) with an M10 x 48mm Bolt (50) and an M10 Nylon Locknut (42). Make sure that the Cable Trap is turned to hold the Cable in place. 49. Wrap the Low Cable (86) under a 90mm Pulley 49 (82). Attach the Pulley to - Weider 8630 | Canadian English Manual - Page 20
50. Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach the Small Backrest (18) to the Ab Upright (1) with two M6 x 63mm Machine Screws (64) and two M6 Washers (37). 18 1 37 64 51. Insert an M6 x 52mm Carriage Bolt (61) through the center hole in a Seat Plate (41). Attach the Seat - Weider 8630 | Canadian English Manual - Page 21
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in - Weider 8630 | Canadian English Manual - Page 22
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments - Weider 8630 | Canadian English Manual - Page 23
77) and the Seat Knob (30). For some exercises, the Seat (17) must be removed. First LEVER TO THE LOW PULLEY STATION To use the Leg Lever (15), the seat must Cable (86) with a Cable Clip (33). Attach the other end of the Chain to the Eyebolt (79) with another Cable Clip. ADJUSTING THE LEG PRESS PLATE - Weider 8630 | Canadian English Manual - Page 24
12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES PRESS ARM - Weider 8630 | Canadian English Manual - Page 25
and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch - Weider 8630 | Canadian English Manual - Page 26
the Butterfly Cable (89). Use the diagrams to be sure that the cables have been assembled correctly. The starting and ending points of each cable have been labeled. The numbers show the proper route for each cable. IMPORTANT: If the cables have not been correctly routed, the weight system will not - Weider 8630 | Canadian English Manual - Page 27
High Cable (85) High Pulley-1 4 2 3 Weight Stack-5 Rear Cable (87) 1-Top Frame 3 2 4-Weight Stack 27 - Weider 8630 | Canadian English Manual - Page 28
chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part from the PART LIST in the center of this manual. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part - Weider 8630 | Canadian English Manual - Page 29
PART IDENTIFICATION CHART-Model No. WESY8630C.5 R0606A M6 Nylon Locknut (44) M8 Nylon Locknut (40) M10 Nylon Locknut (42) M6 Washer (37) M8 Washer (20) M10 Washer (38) M6 x 16mm Screw (59) M5 x 25mm Tap Screw (72) M6 x 63mm Machine Screw (64) M6 x 63mm Carriage Bolt (60) M8 x 63mm Bolt (39) M10 x - Weider 8630 | Canadian English Manual - Page 30
M10 x 195mm Bolt (52) M8 x 67mm Bolt (55) M8 x 63mm Carriage Bolt (49) M8 x 70mm Carriage Bolt (77) M8 x 69mm Shoulder Bolt (43) M10 x 80mm Bolt (71) M10 x 82mm Bolt (66) M10 x 92mm Bolt (76) M10 x 97mm Bolt (95) M10 x 120mm Bolt (74) M8 x 152mm Bolt (67) - Weider 8630 | Canadian English Manual - Page 31
RREEMMOOVVEETTHHIISS PPAARRTT LLIISSTT//EEXXPPLLOODDEEDD DRADWRIANWGINFGROFMROTMHETHMEAMNUAANLU.ASLA!VE THE PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE. 81 - Weider 8630 | Canadian English Manual - Page 32
Cable 88 1 Press Cable 89 1 Butterfly Cable 90 16 Weight 91 2 M10 x 57mm Bolt 92 2 25mm Inner Cap 93 2 Weight Pin 94 2 Pulley Cover 95 1 M10 x 97mm Bolt 96 1 Handle # 1 User's Manual # 1 Exercise Guide # 2 Grease Packet Note: "#" indicates a non-illustrated part - Weider 8630 | Canadian English Manual - Page 33
EXPLODED DRAWING-Model No. WESY8630C.5 55 56 55 40 55 20 55 43 87 42 20 69 20 56 89 51 47 42 76 40 3 51 42 38 38 2 50 56 82 85 76 50 40 82 69 80 42 40 56 67 40 50 92 89 50 82 80 82 80 82 42 50 42 40 42 47 48 45 40 45 46 6 67 40 4 64 37 40 46 80 23 87 32 40 - Weider 8630 | Canadian English Manual - Page 34
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. When ordering parts, please be prepared to give the following information: • the MODEL NUMBER of the product (WESY8630C.5) • the NAME of the product (WEIDER 8630 weight system) • the SERIAL NUMBER of
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 8:00 until 17:00 EST
(excluding holidays)
OR E-MAIL US:
Model No. WESY8630C.5
Serial No.
Write the serial number in the space
above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal (Under Seat)
www.weiderfitness.com
Visit our website at