Weider 8950 Uk Manual
Weider 8950 Manual
 |
View all Weider 8950 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 8950 manual content summary:
- Weider 8950 | Uk Manual - Page 1
& Fitness, Ltd. Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds, LS118JG UK email: [email protected] CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.iconeurope.com - Weider 8950 | Uk Manual - Page 2
BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 15 WEIGHT RESISTANCE CHART 16 CABLE DIAGRAM 17 TROUBLESHOOTING AND MAINTENANCE 18 ORDERING REPLACEMENT PARTS Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the centre of this manual. Remove the PART IDENTIFICATION - Weider 8950 | Uk Manual - Page 3
the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 12. Make sure that the cables remain on the pulleys at all times. If the cables bind whilst you are exercising, stop - Weider 8950 | Uk Manual - Page 4
strength, or improve your cardiovascular system, the WEIDER® 8950 weight system will help you to achieve the results you want. For your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Department at 08457 089 009 - Weider 8950 | Uk Manual - Page 5
manual is designed to ensure that the weight system can be assembled successfully by anyone. However, it is important to realise that the versatile weight system all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented - Weider 8950 | Uk Manual - Page 6
must be able to pivot easily. 39 66 71 69 25 71 3 69 1 3. Set two Weight Bumpers (17) over the indicated 3 holes in the Stabiliser (2). Insert two Weight Guides (10) into the same holes. Secure the Weight Guides in place with two M10 x 70mm Bolts (57), two M10 Washers (70), two M10 x 12 - Weider 8950 | Uk Manual - Page 7
Upright (3) with two M8 x 68mm Bolts (63) and two M8 Nylon Locknuts (69). Do not tighten the Locknuts yet. Attach the Top Frame (4) between the Weight Guides (10) with an M10 x 155mm Bolt (62), two M10 Washers (70), and an M10 Nylon Locknut (68). Tighten the Nylon Locknuts (68, 69) used in - Weider 8950 | Uk Manual - Page 8
ARM ASSEMBLY 7. Press two 45mm Square Inner Caps (24) into the Leg Lever (9). Lubricate an M10 x 73mm Bolt (74) with grease. Attach the Leg Lever (9) to the Seat Frame (8) with the Bolt and an M10 Nylon Locknut (68). Make sure the warning decal is in the indicated position. Do not overtighten the - Weider 8950 | Uk Manual - Page 9
10. Insert the post on the Left Arm (7) through the hole in the Press Frame (5). Be sure the Arm is behind the indicated bracket on the Press Frame. Slide a 25mm Washer (29) over the post on the Left Arm (7). Attach an M6 x 43mm Bolt (61) to the post with an M6 Nylon Locknut (72). Be sure the - Weider 8950 | Uk Manual - Page 10
inset 69 drawing. Attach the Small "U"-bracket (11) to the Weight Tube (12) with an M8 x 45mm Bolt (60) and an M8 Nylon Locknut (69). Do not overtighten the Locknut; the Weight Tube must be able to pivot in the Small "U"-bracket. 16. Locate the Press - Weider 8950 | Uk Manual - Page 11
18. Wrap the Press Cable (49) under a 90mm Pulley 18 (34). Attach the Pulley and a pair of Pulley Covers (35) to the Offset Double "U"-bracket (42) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure the small tabs on the Pulley Covers are on top. 19. Attach the Pulley Arm ( - Weider 8950 | Uk Manual - Page 12
22. Wrap the Short Cable (47) over a 90mm Pulley (34). Attach the Pulley and a pair of Pulley 22 Covers (35) to the Offset Double "U"-bracket (42) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure the small tabs on the Pulley Covers are on bottom. 52 42 35 68 34 47 35 - Weider 8950 | Uk Manual - Page 13
26. Wrap the Low Cable (48) under a 90mm Pulley 26 (34). Attach the Pulley and a pair of Pulley Covers (35) to the bracket on the Base (1) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure the small tabs on the Pulley Covers are on top. 35 48 34 52 35 68 1 27. Route - Weider 8950 | Uk Manual - Page 14
the problem. IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 17 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TROUBLESHOOTING AND - Weider 8950 | Uk Manual - Page 15
section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned with a damp cloth - Weider 8950 | Uk Manual - Page 16
weight resistance at each exercise station. "Top" refers to the 6-lb. top weight. The other numbers refer to the 12.5-lb. weight plates. Weight station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. WEIGHT Top 1 2 3 4 5 6 7 - Weider 8950 | Uk Manual - Page 17
Cable (50). Use the diagrams to make sure that the cables have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may occur. The numbers show the correct route for each cable. Press Cable (49) 5 2 4 1 High Cable (50 - Weider 8950 | Uk Manual - Page 18
TROUBLESHOOTING AND MAINTENANCE TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack . Make sure that the cables are not too tight, or the Top Weight (14) will be lifted. 44 52 68 35 43 52 47 71 69 68 35 18 - Weider 8950 | Uk Manual - Page 19
NOTES 19 - Weider 8950 | Uk Manual - Page 20
ordering replacement parts: • The MODEL NUMBER of the product (WEEMSY18220) • The NAME of the product (WEIDER® 8950 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached - Weider 8950 | Uk Manual - Page 21
assembly. The number in parenthesis below each part refers to the key number of the part from the PART LIST in the centre of this manual. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it - Weider 8950 | Uk Manual - Page 22
PART IDENTIFICATION CHART-Model No. WEEMSY18220 R0504A M10 Nylon Locknut (68) M8 Nylon Locknut (69) 19mm Round Inner Cap (22) M10 x 22mm Spacer (51) 25mm Round Inner Cap (23) M6 Nylon Locknut (72) 25mm Round Outer Cap (27) M10 x 12.5mm Spacer (37) 25mm x 50mm Inner Cap (25) 38mm x 50mm - Weider 8950 | Uk Manual - Page 23
M6 x 63mm Screw (67) M6 x 58mm Bolt (65) M10 x 52mm Bolt (52) M10 x 50mm Bolt (53) M8 x 45mm Bolt (60) M6 x 43mm Bolt (61) M6 x 16mm Screw (40) M8 x 63mm Bolt (66) M8 x 64mm Shoulder Bolt (56) M6 Washer (73) M10 x 65mm Bolt (55) M8 x 63mm Carriage Bolt (58) M8 Washer (71) M8 x 68mm Bolt (63) - Weider 8950 | Uk Manual - Page 24
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL. SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE 81 - Weider 8950 | Uk Manual - Page 25
73 6 M6 Washer 74 1 M10 x 73mm Bolt # 1 User's Manual # 1 Exercise Guide # 1 Grease Packet Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user's manual for information about ordering replacement parts. - Weider 8950 | Uk Manual - Page 26
EXPLODED DRAWING-Model No. WEEMSY18220 R0504A 64 70 25 27 29 26 49 5 28 61 6 72 70 68 27 30 29 26 28 72 36 34 53 34 55 37 52 26 68 4 68 70 68 52 32 31 33 37 70 50 35 34 35 38 54 63 39 35 52 34 35 44 35 34 68 35 44 35 34 35 73 65 73 23 24 20 24 61 23 73 49 7 20 35
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No. WEEMSY18220
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, please call:
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
www.iconeurope.com
Visit our website at
08457 089 009