Weider 900 Uk Manual
Weider 900 Manual
 |
View all Weider 900 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 900 manual content summary:
- Weider 900 | Uk Manual - Page 1
& Fitness, Ltd. Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds, LS118JG UK email: [email protected] CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.iconeurope.com - Weider 900 | Uk Manual - Page 2
ADJUSTMENT 16 WEIGHT RESISTANCE CHART 17 CABLE DIAGRAM 18 TROUBLESHOOTING AND MAINTENANCE 19 PART LIST 21 EXPLODED DRAWING 22 is missing or illegible, call the telephone number on the front cover of this manual and order a free replacement decal. Apply the decal in the location shown. VERTICAL - Weider 900 | Uk Manual - Page 3
the weight system only as described in this manual. 6. Inspect and properly tighten all parts regularly from moving parts. 10. The weight system is designed to support a maximum user weight of 300 lbs (135 kg). 4. with pre-existing health problems. Read all instructions before using. ICON assumes - Weider 900 | Uk Manual - Page 4
The model number is WEEVSY1326.0. The serial number can be found on a decal attached to the weight system (see the front cover of this manual for the location of the decal). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. High Pulley - Weider 900 | Uk Manual - Page 5
PART IDENTIFICATION CHART M6 x 16mm Screw (40) M6 Washer (73) M6 x 63mm Screw (67) M6 x 58mm Screw (65) M10 x 52mm Bolt (52) M8 Washer (71) M10 x 46mm Bolt (53) M8 x 45mm Bolt (60) M10 Washer (70) M6 x 43mm Bolt (61) M6 Nylon Locknut (72) M8 Nylon Locknut (69) 25mm Washer (29) M10 Nylon - Weider 900 | Uk Manual - Page 6
Make Things Easier for Yourself Everything in this manual is designed to ensure that the weight system the packing materials until assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented - Weider 900 | Uk Manual - Page 7
71 71 69 3 3. Set the two Weight Bumpers (17) over the indi- 3 cated holes in the Stabilizer (2). Orient the two Weight Guides (10) so that the indicated holes are near the lower ends. Insert the Weight Guides into the Weight Bumpers (17) and the holes in the Stabilizer (2). Attach the Weight - Weider 900 | Uk Manual - Page 8
holes in a Weight (15) with grease. Slide the Weight onto the Weight Guides (10). 10 Lubricate 15 3 12 15 5. Attach the Top Frame (4) to Do not tighten the Nylon Locknuts yet. Attach the Top Frame (4) between the Weight Guides (10) with an M10 x 155mm Bolt (62), two M10 Washers (70), and - Weider 900 | Uk Manual - Page 9
ARM ASSEMBLY 7 7. Apply grease to an M10 x 125mm Bolt (64). Orient the Press Frame (5) with the bracket on the side shown. Attach the Press Frame to the Top Frame (4) with the Bolt, two M10 Washers (70), and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the Press Frame must - Weider 900 | Uk Manual - Page 10
CABLE ASSEMBLY 10 10. See the CABLE DIAGRAM on page 18 for proper cable routing. Identify the High Cable (50). Route the threaded shaft end of the Cable up through the Top Frame (4) and over a 90mm Pulley (34). Attach the Pulley inside the Top Frame with an M10 x 65mm Bolt (55), two M10 Washers ( - Weider 900 | Uk Manual - Page 11
14. Attach the end of the High Cable (50) to the 14 Small "U"-bracket (11) with an M8 Washer (71) and an M8 Nylon Locknut (69). Note: Do not completely tighten the Nylon Locknut; it should be threaded onto the Cable so that two threads show past the Nylon Locknut, as shown in the inset - Weider 900 | Uk Manual - Page 12
18. Apply grease to an M10 x 78mm Bolt (54). 18 Attach a Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the Pulley Arm must pivot easily. Route the Press Cable (49) over a 90mm Pulley (34). Attach the Pulley, a Cable Trap ( - Weider 900 | Uk Manual - Page 13
21. Route the Short Cable (47) over a 90mm Pulley 21 (34). Attach the Pulley and two Finger Guards (35) to the Double "U"-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 53 35 35 42 68 47 34 22. Attach the end of the Short Cable (47) to the "U"-bracket (43) with an M8 - Weider 900 | Uk Manual - Page 14
25. Route the Low Cable (48) under a 90mm Pulley 25 (34). Attach the Pulley and two Finger Guards (35) to the bracket on the Base (1) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 26. Route the Low Cable (48) over a 90mm Pulley 26 (34). Attach the Pulley, a Cable Trap (36), and - Weider 900 | Uk Manual - Page 15
smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used will need to remove it by tightening the cables; see TROUBLESHOOTING AND MAINTENANCE on page 19. 15 - Weider 900 | Uk Manual - Page 16
ADJUSTMENT This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time you use the weight system. Replace any worn - Weider 900 | Uk Manual - Page 17
: The actual resistance at each station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. WEIGHT 1 2 3 4 5 6 7 8 9 Note: 1 lb. = 0.454 kg PRESS ARM (lbs.) 35 50 66 81 94 111 132 155 170 BUTTERFLY ARM (lbs.) 19 28 36 45 55 - Weider 900 | Uk Manual - Page 18
CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (47), the Low Cable (48), the Press Cable (49), and the High Cable (50). Use the diagrams to make sure that the cables have been assembled correctly. If the cables have not been correctly routed, the weight system will - Weider 900 | Uk Manual - Page 19
TROUBLESHOOTING AND MAINTENANCE TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If - Weider 900 | Uk Manual - Page 20
NOTES 20 - Weider 900 | Uk Manual - Page 21
70 15 M10 Washer 71 4 M8 Washer 72 2 M6 Nylon Locknut 73 6 M6 Washer 74 2 25mm Round Thin Cap # - User's Manual # - Exercise Guide # - Grease Packet Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user - Weider 900 | Uk Manual - Page 22
EXPLODED DRAWING A-Model No. WEEVSY1326.0 R0906A 70 25 64 27 29 26 49 5 28 61 70 68 27 29 26 6 72 28 72 73 49 24 61 7 65 20 73 24 74 23 73 34 36 53 34 26 55 68 4 70 37 50 53 68 37 70 68 35 34 35 20 65 45 73 24 74 45 35 52 36 34 35 35 44 36 34 44 68 35 19 56 - Weider 900 | Uk Manual - Page 23
EXPLODED DRAWING B-Model No. WEEVSY1326.0 R0906A 32 31 33 62 70 70 68 52 38 35 36 34 35 68 54 63 68 39 66 71 70 25 71 69 18 69 54 35 36 38 68 70 34 35 52 68 67 73 73 67 35 34 35 53 68 42 3 68 53 68 70 69 48 35 69 34 35 14 70 34 14 46 36 70 51 55 35 34 68 53 48 51 70 35 - Weider 900 | Uk Manual - Page 24
of the product (WEEVSY1326.0) • the NAME of the product (WEIDER 900 weight system) • the SERIAL NUMBER of the product (see the front cover of this manual) • the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on pages 21 to 23) Part No. 242331 R0906A
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No. WEEVSY1326.0
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
www.iconeurope.com
Visit our website at
08457 089 009